Supported Cobalt Oxide Nanoparticles As Catalyst for Aerobic Oxidation of Alcohols in Liquid Phase

Unprecedented selectivity behavior in the direct dehydrogenation of n-butane to n-butenes with similar active Pt nanoparticle size: unveiling structural and electronic characteristics of supported monometallic catalysts

In this work, supported Pt monometallic catalysts were prepared using oxide and carbon supports by conventional impregnation methods. Similar Pt metallic nanoparticle sizes (mean sizes about 1.8-2 nm) have been obtained using different Pt precursor loadings (0.3 to 5 wt%). For comparison, catalysts with larger nanoparticle sizes were prepared using the liquid phase reduction method. Characterization results indicate different electronic and structural characteristics for the Pt nanoparticles, comparing nanoparticles with similar and different sizes, implying that both the Pt loading and the preparation method affect the formation of different metallic phases. We used the direct dehydrogenation of n-butane to n-butenes reaction as a test reaction to study the catalytic behavior of the Pt nanoparticles obtained at different Pt atomic concentrations. Surprisingly, Pt catalysts with the lowest metallic loading show the highest selectivities to olefins. Besides, Pt catalysts supported on carbon materials showed higher selectivity to butenes than those supported on oxide materials, this was attributed to a higher electron density in the Pt active sites. Likewise, at low Pt loadings, the CNP-supported Pt nanoparticles could be confined at the defect in the nanotube structure as crystalline agglomerates of atoms with few layers or monolayers with very few surface adatom or stepped adatom nanostructures or simply as a group of atoms, thus creating active Pt sites that favor the dehydrogenation reaction over secondary reactions.

Radical-driven selective oxidation of benzyl alcohol on MnCoOx catalysts with no oxidant other than air in reactor

Mn reinforced Co3O4 catalysts (MnCoOx) were prepared by a facile solid phase mixed foaming method with an in-situ heating enhancement for the formation of spinel phase mixed oxide species, and studied in the selective oxidation of benzyl alcohol just the air in reactor as oxygen donor. It was found that the MnCoOx catalysts are composed of relatively minimal spinel MnCo2O4 mixed oxide and massive Co3O4 to form MnCo2O4-Co3O4 oxide pair. The micro-domains of MnCo2O4-Co3O4 oxide pair present two redox couples of Mn3+/Mn2+ and Co3+/Co2+ instead of the single one of Co3+/Co2+ in Co3O4, and then dramatically enhance the formation of superoxide radicals (•O2-) species from the O2 in air, which can efficiently initiate the conversion of benzyl alcohol to benzaldehyde in a Fenton-like processes. With no oxidant other than air in reactor, the interaction between MnCo2O4 and Co3O4 in MnCoOx catalysts leads to a benzyl alcohol conversion up to 98 % with a 100 % benzaldehyde selectivity at atmospheric pressure while single component Co3O4 can only present a benzyl alcohol conversion at 37 %. This embodiment of highly efficient heterogeneous selective oxidation just with air as oxidant provides a probability for developing a low-cost and super-facile radical-induced selective oxidation process for alcohols.

Schiff Base Functionalized Cellulose: Towards Strong Support-Cobalt Nanoparticles Interactions for High Catalytic Performances

A new hybrid catalyst consisting of cobalt nanoparticles immobilized onto cellulose was developed. The cellulosic matrix is derived from date palm biomass waste, which was oxidized by sodium periodate to yield dialdehyde and was further derivatized by grafting orthoaminophenol as a metal ion complexing agent. The new hybrid catalyst was characterized by FT-IR, solid-state NMR, XRD, SEM, TEM, ICP, and XPS. The catalytic potential of the nanocatalyst was then evaluated in the catalytic hydrogenation of 4-nitrophenol to 4-aminophenol under mild experimental conditions in aqueous medium in the presence of NaBH4 at room temperature. The reaction achieved complete conversion within a short period of 7 min. The rate constant was calculated to be K = 8.7 × 10-3 s-1. The catalyst was recycled for eight cycles. Furthermore, we explored the application of the same catalyst for the hydrogenation of cinnamaldehyde using dihydrogen under different reaction conditions. The results obtained were highly promising, exhibiting both high conversion and excellent selectivity in cinnamyl alcohol.

Electrocatalytic Oxidation of Methanol and Ethanol with 3d-Metal Based Anodic Electrocatalysts in Alkaline Media Using Carbon Based Electrode Assembly

Homogeneous electrocatalytic systems based on readily available, earth-abundant, inexpensive base metals Ni, Co, and Cr have been formulated for the electro-oxidation of alcohols (methanol and ethanol) that constitute a key half-cell component of direct alcohol fuel cells (DAFCs). Notably, excellent results were obtained for both methanol as well as ethanol electro-oxidation while operating with a half-cell assembly based on all-non-noble working and counter electrode systems consisting of glassy carbon and graphite rod, respectively. Using NaOH as the supporting electrolyte, Ni/Co/Cr metal salts and their bis(iminopyridine) complexes have been used as anodic electrocatalysts for the alcohol half-cell reactions, and among them, catalytic systems based on Co outperformed the corresponding systems based on Ni and Cr. The system comprising CoCl2.·6H2O [10 mM] + NaOH [6 M] at room temperature emerged as the best electrocatalyst for both methanol [5 M] electro-oxidation (ca. 522.5 ± 13.5 mA cm-2 at 1.4 V) and ethanol [5 M] electro-oxidation (ca. 209 ± 25 mA cm-2 at 1.34 V). It was observed that regardless of the starting alcohol, the end product is carbon dioxide, all of which gets trapped as sodium carbonate (up to 97% yield), thereby mitigating any possible hazards of greenhouse gas emission. Inferences obtained from FETEM, FESEM, and EDS analysis of both the electrolyte solution and residues deposited on the electrode surface provide evidence for the mostly homogeneous nature of the reaction mixture with the molecular catalyst being the major contributor toward the electrocatalytic activity apart from the minor role played by trace heterogeneous particles. The current cell assembly operating with non-noble working and counter electrodes utilizing a catalytic system based on an earth-abundant, base metal salt/complex that not only results in good half-cell current densities for high-energy power-source DAFCs but also generates high-value sodium carbonate offers an exciting avenue.

Cobalt oxide nanoparticles: An effective growth promoter of Arabidopsis plants and nano-pesticide against bacterial leaf blight pathogen in rice

Recently, the application of cobalt oxide nanoparticles (Co₃O₄NPs) has gained popularity owing to its magnetic, catalytic, optical, antimicrobial, and biomedical properties. However, studies on its use as a crop protection agent and its effect on photosynthetic apparatus are yet to be reported. Here, Co₃O₄NPs were first green synthesized using Hibiscus rosa-sinensis flower extract and were characterized using UV-Vis spectroscopy, Fourier transform infrared spectroscopy, X-ray diffraction (XRD), transmission/scanning electron microscopy methods. Formation of the Co₃O₄NPs was attested based on surface plasmon resonance at 210 nm. XRD assay showed that the samples were crystalline having a mean size of 34.9 nm. The Co₃O₄NPs at 200 µg/ml inhibited the growth (OD₆₀₀ = 1.28) and biofilm formation (OD₅₇₀ = 1.37) of Xanthomonas oryzae pv. oryzae (Xoo) respectively, by 72.87% and 79.65%. Rice plants inoculated with Xoo had disease leaf area percentage (DLA %) of 57.25% which was significantly reduced to 11.09% on infected plants treated with 200 µg/ml Co₃O₄NPs. Also, plants treated with 200 µg/ml Co₃O₄NPs only had significant increment in shoot length, root length, fresh weight, and dry weight in comparison to plants treated with double distilled water. The application of 200 µg/ml Co₃O₄NPs on the Arabidopsis plant significantly increased the photochemical efficacy of PSII (ΦPSII) and photochemical quenching (qP) respectively, by 149.10% and 125.00% compared to the control while the non-photochemical energy dissipation (ΦNPQ) was significantly lowered in comparison to control. In summary, it can be inferred that Co₃O₄NPs can be a useful agent in the management of bacterial phytopathogen diseases.

Co-Doped Mn3 O4 Nanocubes via Galvanic Replacement Reactions for Photocatalytic Reduction of CO2 with High Turnover Number

The synthesis of Co-doped Mn₃ O₄ nanocubes was achieved via galvanic replacement reactions for photo-reduction of CO₂ . Co@Mn₃ O₄ nanocubes could efficiently photo-reduce CO₂ to CO with a remarkable turnover number of 581.8 using [Ru(bpy)₃ ]Cl₂  ⋅ 6H₂ O as photosensitizer and triethanolamine as sacrificial agent in acetonitrile and water. The galvanic replaced Co species are homogeneously distributed at the outer surface of Mn₃ O₄ , providing catalytic active sites during CO₂ reduction reactions, which facilitate the separation and migration of photogenerated charge carriers, further benefiting the outstanding photocatalytic performance of CO₂ reduction. Density functional theory calculations revealed that the decreasing of conduction band maximum in Co@Mn₃ O₄ was beneficial to the electron attachment from the excited sensitized molecule, which promoted photocatalytic reduction of CO₂ .

Photocatalytic cascade reactions and dye degradation over CdS-metal-organic framework hybrids

Two bifunctional CdS–MOF composites have been designed and fabricated. The hybrids exhibited synergistic photocatalytic performance toward two cascade reactions under visible light integrating photooxidation activity of CdS and Lewis acids/bases of the MOF. The composite further promoted the photodegradation of dyes benefiting from effective electron transfer between the MOF and CdS.

Two bifunctional CdS–MOF composites have been successfully fabricated and exhibited synergistic photocatalytic performance toward two-step cascade reactions and dye photodegradation.

Oxidation of Benzyl Alcohol Using Cobalt Oxide Supported Inside and Outside Hollow Carbon Spheres

Cobalt oxide nanoparticles (6 nm) supported both inside and outside of hollow carbon spheres (HCSs) were synthesized by using two different polymer templates. The oxidation of benzyl alcohol was used as a model reaction to evaluate the catalysts. PXRD studies indicated that the Co oxidation state varied for the different catalysts due to reduction of the Co by the carbon, and a metal oxidation step prior to the benzyl alcohol oxidation enhanced the catalytic activity. The metal loading influenced the catalytic efficiency, and the activity decreased with increasing metal loading, possibly due to pore filling effects. The catalysts showed similar activity and selectivity (to benzaldehyde) whether placed inside or outside the HCS (63 % selectivity at 50 % conversion). No poisoning was observed due to product build up in the HCS.

Controlled Thermal Conversion Strategy to Provide Metal-Organic Framework-Supported Composite Catalysts

Metal-organic framework (MOF)-supported metal/metal compound nanoparticles (NPs) have emerged as a new class of composite catalysts. However, huge challenges prevail in placing such NPs in the MOF pores because of the poor solubility of metal/metal oxides, limited availability of suitable precursors, metastable attribute of given metal ions, and lower thermal stability of MOFs compared to conventional porous materials. Based on the difference between the thermal stability of the precursor and MOFs, we successfully developed a controlled thermal conversion (CTC) method to load cobalt(II) oxide (CoO) NPs into the framework of MOF (MIL-101) to conveniently obtain a composite catalyst, CoO@MIL-101, which is a very rare example of pure CoO NP-loaded composite catalyst that shows excellent catalytic activity in the selective oxidation of benzyl alcohol. This CTC strategy opens up a pathway for impregnating MOF supports with specific NPs, which is further confirmed by preparing the first CuBr@MOF-type composite catalyst.

Cobalt Single Atoms Embedded in Nitrogen-Doped Graphene for Selective Oxidation of Benzyl Alcohol by Activated Peroxymonosulfate

The development of novel single atom catalyst (SAC) is highly desirable in organic synthesis to achieve the maximized atomic efficiency. Here, a Co-based SAC on nitrogen-doped graphene (SACo@NG) with high Co content of 4.1 wt% is reported. Various characterization results suggest that the monodispersed Co atoms are coordinated with N atoms to form robust and highly effective catalytic centers to activate peroxymonosulfate (PMS) for organic selective oxidation. The catalytic performance of the SACo@NG/PMS system is conducted on the selective oxidation of benzyl alcohol (BzOH) showing high efficiency with over 90% conversion and benzaldehyde selectivity within 180 min under mild conditions. Both radical and non-radical processes occurred in the selective oxidation of BzOH, but the non-radical oxidation plays the dominant role which is accomplished by the adsorption of BzOH/PMS on the surface of SACo@NG and the subsequent electron transfer through the carbon matrix. This work provides new insights to the preparation of efficient transition metal-based single atom catalysts and their potential applications in PMS mediated selective oxidation of alcohols.

Improved Oxygen Activation over a Carbon/Co3O4 Nanocomposite for Efficient Catalytic Oxidation of Formaldehyde at Room Temperature

Oxygen activation is a key step in the catalytic oxidation of formaldehyde (HCHO) at room temperature. In this study, we synthesized a carbon/Co₃O₄ nanocomposite (C-Co₃O₄) as a solution to the insufficient capability of pristine Co₃O₄ (P-Co₃O₄) to activate oxygen for the first time. Oxygen activation was improved via carbon preventing the agglomeration of Co₃O₄ nanoparticles, resulting in small particles (approximately 7.7 nm) and more exposed active sites (oxygen vacancies and Co³⁺). The removal efficiency of C-Co₃O₄ for 1 ppm of HCHO remained above 90%, whereas P-Co₃O₄ was rapidly deactivated. In static tests, the CO₂ selectivity of C-Co₃O₄ was close to 100%, far exceeding that of P-Co₃O₄ (42%). Various microscopic analyses indicated the formation and interaction of a composite structure between the C and Co₃O₄ interface. The carbon composite caused a disorder on the surface lattice of Co₃O₄, constructing more oxygen vacancies than P-Co₃O₄. Consequently, the surface reducibility of C-Co₃O₄ was improved, as was its ability to continuously activate oxygen and H₂O into reactive oxygen species (ROS). We speculate that accelerated production of ROS helped rapidly degrade intermediates such as dioxymethylene, formate, and carbonate into CO₂. In contrast, carbonate accumulation on P-Co₃O₄ surfaces containing less ROS may have caused P-Co₃O₄ inactivation. Compared with noble nanoparticles, this study provides a transition metal-based nanocomposite for HCHO oxidation with high efficiency, high selectivity, and low cost, which is meaningful for indoor air purification.

Green Procedure for Aerobic Oxidation of Benzylic Alcohols with Palladium Supported on Iota-Carrageenan in Ethanol

The search for selective heterogeneous catalysts for the aerobic oxidation of alcohols to ketones and aldehydes has drawn much attention in the last decade. To that end, different palladium-based catalysts have been proposed that use various organic and inorganic supports. In addition, supports that originate from a biological and renewable source that is also nontoxic and biodegradable were found to be superior. We heterogenized palladium chloride or acetate complexes with triphenylphosphine trisulfonate on iota-carrageenan xerogel by simple mixing of the complex and the polysaccharide in water. The resulting polysaccharide-catalyst mixture then underwent deep freeze and lyophilization, after which the catalyst was characterized by TEM, XPS and SEM-EDS and tested in aerobic oxidation. The new heterogeneous catalysts were successfully used for the first time in the aerobic oxidation of benzylic alcohols. Moreover, they were easily removed from the reaction mixture and recycled, yielding an increase in activity with each subsequent reuse. As determined by TEM and XPS, the reduction in palladium and the formation of nanoparticles during the reaction in ethanol yielded more active species and, therefore, higher conversion rates. A SEM-EDS analysis indicated that the palladium was thoroughly dispersed in the xerogel catalysts. Moreover, the xerogel catalyst was observed to undergo a structural change during the reaction. To conclude, the new heterogeneous catalyst was prepared by a simple and straightforward method that used a non-toxic, renewable and biodegradable support to yield an active, selective and recyclable heterogeneous system.

MOF-derived Co3O4-C@FeOOH as an efficient catalyst for catalytic ozonation of norfloxacin

Metal-organic frameworks (MOFs) ZIF-67-derived Co₃O₄-C@FeOOH composite was prepared, characterized and used as an efficinet catalyst for ozonation of norfloxacin (NOF). Results showed that ZIF-67-derived Co₃O₄-C composite maintained the polyhedral structure of ZIF-67. After modification, abundant amorphous FeOOH nanowire attached on the surface of Co₃O₄-C composite, resulting in Co₃O₄-C@FeOOH interwoven polyhedrons. Furthermore, the specific surface area of the formed composite was about 2.5 times that of Co₃O₄-C composite, which might provide more active sites for catalytic reaction. Compared with single ozonation system, the catalytic ozonation process (Co₃O₄-C@FeOOH/O₃) had better performance in NOF mineralization under the same operating conditions. Moreover, in the presence of Co₃O₄-C@FeOOH, faster O₃ decomposition and higher •OH concentration were observed, which could explain the significant enhancement of TOC removal. The co-existence of Fe and Co in various valence states in catalyst might improve the conversion of Co(III)/Co(II) and Fe(III)/Fe(II), which would increase the catalytic activity in catalytic ozonation process. Besides, several main intermediate products were detected and possible NOF degradation pathway was proposed.

Synthesis and Characterization of CoxOy–MnCO3 and CoxOy–Mn2O3 Catalysts: A Comparative Catalytic Assessment Towards the Aerial Oxidation of Various Kinds of Alcohols

CoxOy–manganese carbonate (X%)(CoxOy–MnCO3 catalysts (X = 1–7)) were synthesized via a straightforward co-precipitation strategy followed by calcination at 300 °C. Upon calcination at 500 °C, these were transformed to CoxOy–dimanganese trioxide i.e., (X%)CoxOy–Mn2O3. A relative catalytic evaluation was conducted to compare the catalytic efficiency of the two prepared catalysts for aerial oxidation of benzyl alcohol (BzOH) to benzaldehyde (BzH) using O2 molecule as a clean oxidant without utilizing any additives or alkalis. Amongst the different percentages of doping with CoxOy (0–7% wt./wt.) on MnCO3 support, the (1%)CoxOy–MnCO3 catalyst exhibited the highest catalytic activity. The influence of catalyst loading, calcination temperature, reaction time, and temperature and catalyst dosage was thoroughly assessed to find the optimum conditions of oxidation of benzyl alcohol (BzOH) for getting the highest catalytic efficiency. The (1%)CoxOy–MnCO3 catalyst which calcined at 300 °C displayed the best effectiveness and possessed the largest specific surface area i.e., 108.4 m2/g, which suggested that the calcination process and specific surface area play a vital role in this transformation. A 100% conversion of BzOH along with BzH selectivity >99% was achieved after just 20 min. Notably, the attained specific activity was found to be considerably larger than the previously-reported cobalt-containing catalysts for this transformation. The scope of this oxidation reaction was expanded to various alcohols containing aromatic, aliphatic, allylic, and heterocyclic alcohols without any further oxidation i.e., carboxylic acid formation. The scanning electron microscope (SEM), energy-dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and Brunauer–Emmett–Teller (BET) specific surface area analytical techniques were used to characterize the prepared catalysts. The obtained catalyst could be easily regenerated and reused for six consecutive runs without substantial decline in its efficiency.

A Highly Efficient Bifunctional Catalyst CoOx/tri-g-C3N4 for One-Pot Aerobic Oxidation–Knoevenagel Condensation Reaction

A highly efficient bifunctional catalyst of an s-triazine-based carbon-nitride-supported cobalt oxide is developed for the aerobic oxidation–Knoevenagel condensation tandem reaction of benzyl alcohol and malononitrile, whereby 96.4% benzyl alcohol conversion with nearly 100% selectivity towards benzylmalononitrile can be obtained in 6 h at 80 °C. The excellent catalytic performance derives from the high basicity of carbon nitride and strong redox ability of Co species induced by carbon nitride. The catalyst is also quite stable and can be reused without any regeneration treatment, whose product yield is only an 11.5% reduction after four runs.

Noncovalent immobilization of Co(ii)porphyrin through axial coordination as an enhanced electrocatalyst on carbon electrodes for oxygen reduction and evolution

Noncovalent immobilization of Co(ii)porphyrin on carbon nanotubes through axial coordination provides significantly enhanced electrochemically catalyzed oxygen reduction and oxygen evolution.

Synthesis of new Mn19 analogues and their structural, electrochemical and catalytic properties

We report the synthesis and structural characterisation of new Mn19 and Mn18M analogues, [MnIII12MnII7(μ4-O)8(μ3-OCH3)2(μ3-Br)6(HLMe)12(MeOH)6]Br2 (2) and [MnIII12MnII6Sr(μ4-O8(μ3-Cl)8(HLMe)12(MeCN)6]Cl2 cluster (3), where H3LMe is 2,6-bis(hydroxymethyl)-p-cresol. The electrochemistry of 2 and 3 has been investigated and their activity as catalysts in the oxidation of benzyl alcohol has been evaluated. Selective oxidation of benzyl alcohol to benzaldehyde by O2 was achieved using 1 mol% of catalyst with conversions of 74% (2) and 60% (3) at 140 °C using TEMPO as a co-catalyst. No partial conversion of benzaldehyde to benzoic acid was observed. The results obtained revealed that different operative parameters - such as catalyst loading, temperature, time, solvent and the presence of molecular oxygen - played an important role in the selective oxidation of benzyl alcohol.

"Traditional" Sol-Gel Chemistry as a Powerful Tool for the Preparation of Supported Metal and Metal Oxide Catalysts

The sol-gel method is an attractive synthetic approach in the design of advanced catalytic formulations that are based on metal and metal oxide with high degree of structural and compositional homogeneity. Nowadays, though it originated with the hydrolysis and condensation of metal alkoxides, sol-gel chemistry gathers plenty of fascinating strategies to prepare materials from solution state precursors. Low temperature chemistry, reproducibility, and high surface to volume ratios of obtained products are features that add merit to this technology. The development of different and fascinating procedure was fostered by the availability of new molecular precursors, chelating agents and templates, with the great advantage of tailoring the physico-chemical properties of the materials through the manipulation of the synthesis conditions. The aim of this review is to present an overview of the “traditional” sol-gel synthesis of tailored and multifunctional inorganic materials and their application in the main domain of heterogeneous catalysis. One of the main achievements is to stress the versatility of sol-gel preparation by highlighting its advantage over other preparation methods through some specific examples of the synthesis of catalysts.

Efficient aerobic oxidative desulfurization over Co–Mo–O bimetallic oxide catalysts

Co–Mo–O bimetallic oxides were prepared as efficient catalysts for aerobic oxidative desulfurization with oxygen in air as the oxidant.

Design and synthesis of a highly efficient heterogeneous MnCo2O4 oxide catalyst for alcohol oxidation: DFT insight into the synergistic effect between oxygen deficiencies and bimetal species

We report the design and synthesis of an oxygen vacancy-abundant spinel-structured MnCo₂O₄ oxide as a highly efficient catalyst for alcohol oxidation.

Synthesis and characterization of MgF2–CoF2 binary fluorides. Influence of the treatment atmosphere and temperature on the structure and surface properties

Research was carried out on the incorporation of divalent cobalt cations into the crystalline structure of MgF₂ to form Mg_xCo_1−xF₂ binary fluorides, which had not been investigated before. The above fluorides were obtained by the precipitation from aqueous solution of magnesium and cobalt nitrates with ammonium fluoride. Binary fluorides containing 0.6, 7.5 and 37.7 mol% CoF₂ were prepared. The effects of treatment temperature (300, 400 °C) and atmosphere (oxidizing or reducing) on the structure (XRD, TPR-H₂, UV-Vis), texture (low-temperature N₂ adsorption), surface composition (XPS) and surface acidity (NH₃-TPD) of the binary fluorides were determined. It has been found that in Mg_xCo_1−xF₂ an isomorphic substitution occurs of Mg²⁺ cations by Co²⁺ cations which results in the formation of a rutile-type solid solution. The obtained binary fluorides are characterized by a mesoporous structure and relatively large surface area. It has been found that thermal treatment of the binary fluorides in oxidizing conditions results in the oxidation of CoF₂ to Co₃O₄ even at 300 °C; therefore it is not possible to obtain pure Mg_xCo_1−xF₂ binary fluorides in the presence of air. The preparation of the latter requires reducing conditions, namely thermal treatment of dry precipitate at 300 °C in an atmosphere of hydrogen. If the treatment is conducted at a higher temperature (400 °C), CoF₂ undergoes a partial reduction to metallic cobalt. An XPS study has shown the presence of hydroxyl groups in the investigated samples. However, these are solely surface groups because their presence was not detected by XRD measurements. The binary fluorides obtained by our method are characterized by a very narrow optical energy gap (5.31–3.50 eV), considerably narrower than that recorded for bulk fluorides. Measurements of temperature-programmed desorption of ammonia have shown that the incorporation of cobalt cations into the crystal structure of MgF₂ results in a decrease in the surface acidity of the binary fluorides.

Results of the first research on structural and surface properties of binary fluorides MgF₂–CoF₂ are presented.

Flexible Waterproof Rechargeable Hybrid Zinc Batteries Initiated by Multifunctional Oxygen Vacancies-Rich Cobalt Oxide

Although both are based on Zn, Zn-air batteries and Zn-ion batteries are good at energy density and power density, respectively. Here, we adopted Ar-plasma to engrave a cobalt oxide with abundant oxygen vacancies (denoted as Co₃O_{4- x}). The introduction of oxygen vacancies to cobalt oxide not only promotes its reversible Co-O ↔ Co-O-OH redox reaction but also leads to good oxygen reduction reaction and oxygen evolution (ORR/OER) performance (a half-wave potential of 0.84 V, four-electron transfer process for ORR, and 330 mV overpotential, 58 mV·dec^-1 Tafel slope for OER). We then constructed a battery system based on both Zn-Co₃O_{4- x} and Zn-air electrochemical reactions. The hybrid battery reveals both a high-power density of 3200 W·kg^-1 and high-energy density of 1060 Wh·kg^-1. Furthermore, the developed flexible solid-state hybrid batterydemonstrates good waterproof and washable ability (99.2% capacity retention of after 20 h water soaking test and 93.2% capacity retention after 1 h washing test). Interestingly, the fabricated flexible battery can work under water, and after the power is exhausted, the battery can automatically recover electricity output as long as it is exposed to air. The developed device is suitable for wearable applications considering its electrochemical performances, great environmental adaptation, and "air recoverability". In addition, this study underscores the approach to develop hybrid energy-storage technologies through modification of electrode materials.

Selective Oxidation of Biomass-Derived Alcohols and Aromatic and Aliphatic Alcohols to Aldehydes with O2/Air Using a RuO2-Supported Mn3O4 Catalyst

Selective catalytic oxidation of carbohydrate-derived 5-hydroxymethylfurfural, furfuryl alcohol, and various aromatic and aliphatic compounds to the corresponding aldehyde is a challenging task. The development of a sustainable heterogeneous catalyst is crucial in achieving high selectivity for the desired aldehyde, especially using O2 or air. In this study, a RuO2-supported Mn3O4 catalyst is reported for the selective oxidation reaction. Treatment of MnO2 molecular sieves with RuCl3 in aqueous formaldehyde solution gives a new type of RuO2-supported Mn3O4 catalyst. Detailed catalyst characterization using powder X-ray diffraction, N2 adsorption, scanning and transmission electron microscopes, diffuse reflectance UV-visible spectrometer, and X-ray photoelectron spectroscopy proves that the RuO2 species are dispersed on the highly crystalline Mn3O4 surface. This catalytic conversion process involves molecular oxygen or air (flow, 10 mL/min) as an oxidant. No external oxidizing reagent, additive, or cocatalyst is required to carry out this transformation. This oxidation protocol affords 2,5-diformylfuran, 2-formylfuran, and other aromatic and aliphatic aldehydes in good to excellent yield (70-99%). Moreover, the catalyst is easily recycled and reused without any loss in the catalytic activity.