Preparation of a novel TiO2-based p-n junction nanotube photocatalyst

The role of solution temperature in characteristics of TiO2 nanotube arrays prepared on Ti foil in acid solution

The characteristics of TiO2 nanotube arrays (TNTs) prepared on Ti foil in sulfuric acid solution that contains Cl- under different temperatures are investigated by field emission scanning electron microscopy (FESEM), electrochemical impedance spectroscopy (EIS), Mott-Schottky measurement and Raman spectra. The solution temperature significantly affects the morphologies of TNTs, i.e., when solution temperature rises from -10 °C to 90 °C, the inner diameter of the nanotube increases and the barrier layer thickness decreases, and, as TNTs display n-type semiconductive properties, the donor density (ND) and corrosion protection decrease. Two types (types I and II) of pulse temperature are used to fabricate TNTs, in which type I is firstly anodized at a low temperature for time t, and then increases to a high temperature. While for type II, the solution temperature order is opposite to that of type I. The ND of TNTs in the case of type I is lower than ND of TNTs in the case of type II. ND decreases with the increased pulse step time for type I, while ND increases with the increased pulse step time for type II.

Metal-organic frameworks incorporated with C3N4: A visible light enhanced platform for degradation of polybromodiphenyl ethers

A series of nano-photocatalysts metal-organic frameworks (MOFs)/graphitic carbon nitride (CN) (named MOFCN-x) with high activity have been synthesized by in-situ growth method. Under visible light irradiation, MOFCN-x hybrids show enhanced photocatalytic activity for the debromination of polybromodiphenyl ethers (PBDEs) compared with CN. Among all the hybrids, MOFCN-2 shows the highest reaction rate, which is 3.3 times as high as that in CN. MOFCN-x photocatalysts own stable visible light activity after recycled experiment. It indicates that a moderate amount of MOFs in MOFCN-x can largely enhance the photocatalytic ability by improved visible light absorption, larger specific surface area and better photo-generated charge carriers separation and transfer capabilities. More interestingly, the debromination pathway of PBDEs by MOFCN-x shows obvious selectivity compared with pure CN that bromines at meta-positions are much more susceptible than those at the para- and ortho-positions. The possible photoreductive mechanism has been proposed. This study shows that nanocomposite MOFCN can be an excellent candidate for dealing with halogen pollutants by solar-driven.

Multidimensional applications and potential health implications of nanocomposites

This study reviews the concept, classifications, and techniques involved in the synthesis of nanocomposites. The environmental and health implications of nanoparticles and composite materials were detailed, as well as the applications of nanocomposites in water remediation, antibacterial application, and printed circuit boards. The study gave insights into the challenges of water pollution treatment and provided a broad list of nanocomposites that have been explored for water remediation. Moreover, the emergence of multi-drug resistance to many antibiotics has made current antibiotics inadequate in the treatment of disease. This has engineered the development of alternative strategies in the drug industries for the production of effective therapeutic agents, comprising nanocomposites with antibacterial agents. The new therapeutic agents known as nanoantibiotics are more efficient and have paved the way to handle the challenges of antibiotic resistance. In printed circuit boards, nanocomposites have shown promising applications because of their distinct mechanical, thermal, and electrical characteristics. The uniqueness of the write-up is that it provides a broad explanation of the concept, synthesis, application, toxicity, and harmful effects of nanocomposites. Thus, it will provide all-inclusive awareness to readers to identify research gaps and motivate researchers to synthesize novel nanocomposites for use in various fields.

Silver-Loaded Carbon and Phosphorous Co-Doped Boron Nitride Quantum Dots (Ag@CP-BNQDs) for Efficient Organic Waste Removal: Theoretical and Experimental Investigations

In this paper, silver-loaded phosphorous and carbon co-doped boron nitride quantum dot (Ag@CP-BNQD) nanocomposites were synthesized using a co-precipitation method followed by a hydrothermal approach. The nanocomposites of Ag@CP-BNQDs were characterized by scanning electron microscopy, energy-dispersive spectroscopy, Fourier transform infrared spectroscopy, X-ray diffraction, and ultraviolet-visible spectrophotometry. The as-prepared Ag@CP-BNQDs were used for photocatalytic degradation of 10 common organic pollutants, including dyes, pharmaceuticals, and pesticides in aqueous solution under visible light irradiation. The high-performance photocatalysis of Ag@CP-BNQDs proved that Ag@CP-BNQDs is plasmonic and the n-p junction photocatalyst. Theoretical calculations were done to measure the crystals and electronic structures of Ag@CP-BNQDs. Theoretical results showed that loading of Ag behaves as plasmonic sensitizers and co-catalysts and provides extra bands, which make electron movement easier between valance and conduction bands. The mechanism of the charge separation enhancement was postulated. Our findings might deepen our understanding of how sensitizer surface modification works in photodegradation applications.

Enhanced photocatalytic degradation of Acid Blue dye using CdS/TiO2 nanocomposite

Photocatalytic degradation is essential for the successful removal of organic contaminants from wastewater, which is important for ecological and environmental safety. The advanced oxidation process of photocatalysis has become a hot topic in recent years for the remediation of water. Cadmium sulphide (CdS) nanostructures doped with Titanium oxide (CdS/TiO₂) nanocomposites has manufactured under ambient conditions using a simple and modified Chemical Precipitation technique. The nanocomposites crystal structure, thermal stability, recombination of photo-generated charge carriers, bandgap, surface morphology, particle size, molar ratio, and charge transfer properties are determined. The production of nanocomposites (CdS-TiO₂) and their efficient photocatalytic capabilities are observed. The goal of the experiment is to improve the photocatalytic efficiency of TiO₂ in the visible region by doping CdS nanocomposites. The results showed that as-prepared CdS-TiO₂ nanocomposites has exhibited the highest photocatalytic activity in the process of photocatalytic degradation of AB-29 dye, and its degradation efficiency is 84%. After 1 h 30 min of visible light irradiation, while CdS and TiO₂ showed only 68% and 09%, respectively. The observed decolorization rate of AB-29 is also higher in the case of CdS-TiO₂ photocatalyst ~ 5.8 × 10⁻⁴mol L⁻¹ min⁻¹) as compared to the reported decolorization rate of CdS ~ 4.5 × 10⁻⁴mol L⁻¹ min⁻¹ and TiO₂ ~ 0.67 × 10⁻⁴mol L⁻¹ min⁻¹. This increased photocatalytic effectiveness of CdS-TiO₂ has been accomplished by reduced charge carrier recombination as a result of improved charge separation and extension of TiO₂ in response to visible light.

Remediation of noxious wastewater using nanohybrid adsorbent for preventing water pollution

Removal of toxic elements from wastewater effluent has got a lot of attention because of their severe negative effects on human and environmental health. In the past few years, rapid urbanization and industrial activities in developing countries have exacerbated the destruction of the environment. Most of the wastewater effluents are discharged untreated or inadequately treated, which has become a major concern due to its impact on sustainability and the environment. This is imperative to implement, innovative and resourceful wastewater treatment technologies requiring low investment. Among the various treatment technologies, cutting-edge processes in nano-material sciences have recently piqued the interest of scientists. Nanohybrid absorbents have the potential in improving wastewater treatment and increase water supply by utilizing unconventional water resources. Carbon nanotubes, titanium oxide, manganese oxide, activated carbon (AC), magnesium oxide, graphene, ferric oxides, and zinc oxide are examples of nano-adsorbents that are used to eliminate pollutants. This also demonstrated the effective removal of contaminants along with the harmful effects of chemicals, colorants, and metals found in wastewater. The present manuscript examines potential advances in nanotechnology in wastewater treatment for the prevention of water and soil pollution. This systematic review aims to highlight the importance of nanohybrid absorbents treatment technology for wastewater treatment and to explain how nanohybrid absorbents have the potential to revolutionize industrial pollution. There are also other published review articles on this topic but the present review covers an in-depth information on nano-adsorbents and their targeted contaminants.

Studies on Electron Escape Condition in Semiconductor Nanomaterials via Photodeposition Reaction

In semiconductor material-driven photocatalysis systems, the generation and migration of charge carriers are core research contents. Among these, the separation of electron-hole pairs and the transfer of electrons to a material’s surface played a crucial role. In this work, photodeposition, a photocatalysis reaction, was used as a “tool” to point out the electron escaping sites on a material’s surface. This “tool” could be used to visually indicate the active particles in photocatalyst materials. Photoproduced electrons need to be transferred to the surface, and they will only participate in reactions at the surface. By reacting with escaped electrons, metal ions could be reduced to nanoparticles immediately and deposited at electron come-out sites. Based on this, the electron escaping conditions of photocatalyst materials have been investigated and surveyed through the photodeposition of platinum. Our results indicate that, first, in monodispersed nanocrystal materials, platinum nanoparticles deposited randomly on a particle’s surface. This can be attributed to the abundant surface defects, which provide driving forces for electron escaping. Second, platinum nanoparticles were found to be deposited, preferentially, on one side in heterostructured nanocrystals. This is considered to be a combination result of work function difference and existence of heterojunction structure.

MXenes based nano-heterojunctions and composites for advanced photocatalytic environmental detoxification and energy conversion: A review

Extensive research is being done to develop multifunctional advanced new materials for high performance photocatalytic applications in the field of energy production and environmental detoxification, MXenes have emerged as promising materials for enhancing photocatalytic performance owing to their excellent mechanical properties, appropriate Fermi levels, and adjustability of chemical composition. Numerous experimental and theoretical research works implied that the dimensions of MXenes have a significant impact on their performance. For photocatalysis to thrive in the future, we must understand the current state of the art for MXene in different dimensions. Using MXene co-catalysts in widely used in photocatalytic applications such as CO₂ reduction, hydrogen production and organic pollutant oxidation, this study focuses on the most recent developments in MXenes based materials, structural modifications, innovations in reaction and material engineering. It has been reported that using 5 mg of CdS-MoS₂-MXene researchers were able to generate as high as 9679 μmol/g/h hydrogen under visible light. The MXenes based heterojunction photocatalyst Co₃O₄/MXene was utilized to degrade 95% bisphenol A micro-pollutant in just 7 min. Numerous novel materials, their preparations and performances have been discussed. Depending upon the nature of MXene-based materials, the synthesis techniques and photocatalytic mechanism of MXenes as co-catalyst are also summarized. Finally, some final thoughts and prospects for developing highly efficient MXene-based photocatalysts are provided which will indeed motivate researchers to design novel hybrid materials based on MXenes for sustainable solutions to energy and pollution issues.

Bimetal (Fe/Zn) doped BiOI photocatalyst: An effective photodegradation of tetracycline and bacteria

Tetracycline (TC) is one of the most commonly used broad-spectrum antibiotics to treat the bacterial infection. TC antibiotics enter into the environment because of partial metabolism in the humans and animals, thereby increasing the environmental toxicity. Therefore, it is highly needed to treat TC antibiotics from the water system. In this aspect, the present work focus on the synthesis of Fe and Zn (bimetal) incorporated with different concentrations into the bismuth-oxy-iodide (Fe/Zn-BiOI) based photocatalyst materials. The synthesized Fe/Zn-BiOI was tested against photocatalytic degradation of TC antibiotics and bacteria. The band gap value of the synthesized Fe/Zn-BiOI was calculated ~2.19 eV. The incorporation of the Fe and Zn metals within the BiOI aided advantages that increased the reactive sites, oxygen defects, photon adsorption, production of hydroxyl radicals, and decrease the recombination rate, thereby high photo-degradation ability. The maximum degradation of ~83% was observed using Fe/Zn-BiOI-1-1 at 10 mg/L of TC antibiotics concentration. Moreover, ~98% of degradation was observed at pH~10 of the TC antibiotics. The photo-activity against bacteria of the Fe/Zn-BiOI was also determined. The data suggested that the synthesized Fe/Zn-BiOI based photocatalyst materials effectively inhibited the bacterial strains. Therefore, Fe/Zn-BiOI based photocatalyst materials might be promising materials that effectively degrade TC antibiotics as well as bacteria.

Electrochemical oxidation of triclosan using Ti/TiO2 NTs/Al-PbO2 electrode: reaction mechanism and toxicity evaluation

5-Chloro-2-(2,4-dichlorophenoxy) phenol (triclosan, TCS) is a potential threat to the environment and human health, and it needs appropriate approaches for its removal. A new modified PbO₂ electrode, Al-PbO₂ based on TiO₂ nanotubes (NTs), was successfully prepared for TCS electrochemical oxidation. Scanning electron microscopy indicated a compact coating layer on the anode. TCS removal on Ti/TiO₂ NTs/Al-PbO₂ anode followed a pseudo-first-order kinetics. The electrical efficiency per log order (EE/O) for oxidation was decreased from 14.79 to 12.90 kWh m^-3 order^-1 after TiO₂ NTs on Ti material and decreased to 8.27 kWh m^-3 order^-1 after Al³⁺ doping. The effects of current density, pH value, and electrolyte concentration were investigated. Intermediate organo-chlorinated compounds were detected by gas chromatography coupled with mass spectrometry, high-performance liquid chromatography, and ion chromatography. Finally, ecotoxicity assessment revealed that the degradation of TCS by electrooxidation system with Ti/TiO₂ NTs/Al-PbO₂ anode could yield a smaller toxicity compared with parent compounds.

Excellent optoelectronic applications and electrical transport behavior of the n-WO3nanostructures/p-diamond heterojunction: a new perspective

Nanostructured n-type metal oxides/p-type boron-doped diamond heterojunctions have demonstrated a typical rectification feature and/or negative differential resistance (NDR) potentially applied in wide fields. Recently, the fabrication and electronic transport behavior of n-WO₃nanorods/p-diamond heterojunction at high temperatures were studied by Wanget al(2017Appl. Phys. Lett.110052106), which opened the door for optoelectronic applications that can operate at high-temperatures, high-power, and in various harsh environments. In this perspective, an overview was presented on the future directions, challenges and opportunities for the optoelectronic applications based on the n-WO₃nanostructures/p-diamond heterojunction. We focus, in particular, on the prospects for its high temperature NDR, UV photodetector, field emission emitters, photocatalyst and optical information storage for a wide range of new optoelectronic applications.

Assemble of Bi-doped TiO2 onto 2D MoS2: an efficient p-n heterojunction for photocatalytic H2 generation under visible light

Fabrication of noble-metal-free, efficient and stable hybrid photocatalyst is essential to address the rapidly growing energy crisis and environmental pollution. Here, MoS₂ has been used as the co-catalyst on Bi-doped TiO₂ to form a novel heterostructure to increase the utilization of the photogenerated charge carriers for improving photocatalytic H₂ evolution activity through water reduction. Significantly increased photocatalytic H₂ generation has been achieved on the optimized MoS₂/Bi-TiO₂ nanocomposite (∼512 μmol g^-1) after 4 h of visible light illumination, which is nine times higher than that of the pristine TiO₂ (∼57 μmol g^-1). The measurements of photocurrent, charge transfer resistance and photo-stability of MoS₂/Bi-TiO₂ photoanode imply that charge separation efficiency has been improved in comparison to the pure MoS₂ and TiO₂ photoanodes. Further, the Mott-Schottky study confirmed that a p-n heterojunction has been formed between n-type MoS₂ and p-type Bi-doped TiO₂, which provides a potential gradient to increase charge separation and transfer efficiency. On the basis of these experimental results, this enhanced photocatalytic activity of MoS₂/Bi-TiO₂ heterostructures could be ascribed to the significant visible light absorption and the efficient charge carrier separation. Thus, this work demonstrates the effect of p-n junction for achieving high H₂ evolution activity and photoelectrochemical water oxidation under visible light illumination.

Enhanced Photocatalytic Activity of TiO2 Modified with GaI toward Environmental Application

Gallium (Ga) ion-doped TiO₂ (Ga-TiO₂) nanocomposite with small particle size (9-10 nm) and high surface area (104 m²/g) has been easily synthesized via sol-gel method at low temperature by using low-valent GaI as a doping precursor. The structural and morphological characterization of Ga-TiO₂ was carried out with standard analytical and spectroscopic techniques. Ga doping into the TiO₂ matrix inhibited a phase transformation from anatase to rutile (photocatalytically inactive) form, even at a higher temperature of 750 °C. Finally, Ga-TiO₂ nanocomposite showed high photocatalytic activity and exhibited 97% degradation of acid violet 63 dye within 60 min. The dye degradation rate constant was calculated as 1.6 × 10^-1 and 1.4 × 10^-1 min^-1 under UV and white light irradiation, respectively, which is higher, as compared to the previously reported Ga-TiO₂ composites to date.

Strategies to improve the photocatalytic activity of TiO2: 3D nanostructuring and heterostructuring with graphitic carbon nanomaterials

TiO2-based photocatalysis has been considered to be one of the most promising avenues for environmental remediation including water purification. However, several technical issues such as the limited surface area of bulk TiO2, the large band gap of TiO2, and rapid charge recombination still limit the practical application of TiO2 photocatalysts. Therefore, here we focus on two structural design strategies: (i) monolithic three-dimensional (3D) nanostructuring, and (ii) heterostructuring with graphitic carbon nanomaterials. A monolithic 3D nanostructure enables maximal surface area in a given volume and efficient reuse of the photocatalyst without recollection. Heterostructuring with carbon nanomaterials helps achieve maximal utilization of the solar spectrum and charge separation and provides efficient TiO2 photocatalysts. In this review, recent progress on TiO2 photocatalysts toward the abovementioned strategies will be summarized. Further discussion and direction will provide insights into the rational design of highly efficient TiO2 photocatalysts, and help develop advanced photocatalyst models.

Ultrasonic Synthesis of Carbon Nanotube-Titanium Dioxide Composites: Process Optimization via Response Surface Methodology

In this study, the central composite design of response surface methodology was applied to optimize the ultrasonic synthesis of multiwalled carbon nanotube-titanium dioxide (MWNT-TiO₂) composites. Twenty composites were prepared by adjusting three parameters (MWNT concentration in water, sonication to disperse/exfoliate MWNTs in water, and sonication to attach TiO₂ onto MWNTs) at five levels. On the basis of the experimental design, semiempirical expressions were developed, analyzed, statistically assessed, and subsequently applied to predict the impact of the studied parameters on composite synthesis. The composite synthesis process was optimized to capture the experimental conditions favoring the highest productivity (i.e., MWNT-TiO₂ formation or percent TiO₂ attachment) utilizing minimal resources. The synthesis process optimization results showed that, to make a MWNT-TiO₂ composite in 10 mL of water, 23.2 mg (∼99% of 23.4 mg) of TiO₂ can be attached to 2.6 mg of MWNTs. This process requires only 727 J sonication energy, of which 592 J is invested to exfoliate MWNTs (Sonication 1) and 135 J to attach TiO₂ (Sonication 2) to MWNTs. Finally, the optimally synthesized composite was extensively characterized using SEM, surface area and porosity analysis, TGA, and ζ-potential analysis/DLS. Also, this composite was tested for stability under variable pH and solvent polarity. The approach developed in this study could be used to optimize the synthesis process of other similar composites.

Synthesis, characterization and computational study of an ilmenite-structured Ni3Mn3Ti6O18 thin film photoanode for solar water splitting

Thin films of a Ni₃Mn₃Ti₆O₁₈ solid solution photoanode have been deposited on an FTO coated glass substrate and experimental results are supported by DFT studies.

Photovoltaic and photocatalytic properties of bismuth oxyiodide-graphene nanocomposites

In this study, we evaluate the photovoltaic and photocatalytic properties of chemical vapor deposited bismuth oxyiodide (BiOI) and bismuth oxyiodide-graphene (BiOI-GR) nanocomposite thin films. The BiOI thin film has an average thickness of 574 nm and a bandgap of around 2 eV. The BiOI and BiOI-GR thin films exhibited nanoflake morphology. It was found that addition of graphene increases absorbance by causing vertical growth of nanoflakes, imparting anti-reflectance and light trapping properties. The photocatalytic activities of the thin films were evaluated by examining methylene blue (MB) degradation under visible light irradiation. BiOI-GR degraded 56.42% of MB in two hours while BiOI degraded 44.16%. Afterwards, FTO|BiOI|graphite|Al and FTO|BiOI-GR|graphite|Al solar cell devices were fabricated with photocurrent density values of 2.0 μA cm-2 and 2.7 μA cm-2, respectively. The improved properties of BiOI-GR are attributed to the anti-reflecting and light trapping properties of vertical BiOI-GR nanoflakes and the enhanced carrier separation due to graphene as an electron acceptor.

Spatial distribution of active sites on a ferroelectric PbTiO3 photocatalyst for photocatalytic hydrogen production

The separation of photogenerated charge carries is a challenging issue in artificial photocatalyst systems for solar energy conversion. It has been reported that spatial charge separation can take place between different facets of semiconductor-based crystals with regular morphology and facets, which could be used to rationally deposit cocatalysts on the right facets. However, the spatial separation of photogenerated electrons and holes is still a big challenge for a particulate photocatalyst without regular morphology and specific facets. In this work, we demonstrated that photogenerated electrons and holes can be regularly separated on ferroelectric PbTiO₃ photocatalyst even without regular morphology and facets. The reduction cocatalyst and oxidation cocatalyst could be selectively formed on different sites via an in situ photochemical deposition method. It is found that the photoactivity and hydrogen production for PbTiO₃ with spatially separated dual-cocatalysts is remarkably enhanced to more than 100 times greater compared to native PbTiO₃, which is much higher than that the case of dual-cocatalysts with a random distribution. The intrinsic electric fields and spontaneous electric polarization in the bulk of PbTiO₃ are proposed to play important roles in the spatial distribution of active sites on irregular PbTiO₃ particles. Our work emphasizes the essential roles of two important factors, efficient charge separation strategy and the location of dual-cocatalysts on the right sites, to construct integrated artificial photocatalyst systems for solar energy conversion.

Stannous oxide promoted charge separation in rationally designed heterojunction photocatalysts with a controllable mechanism

Due to the sluggish mobility of holes, the low charge-separation rate remains an intrinsic issue that limits further increase of the photocatalytic conversion efficiency. Herein, we proposed an in situ hydrothermal method to expedite the charge transfer with enhanced photocatalytic H2 evolution rate and photodegradation activities via introducing SnO microplates into TiO2. As compared to bare TiO2, the SnO/TiO2 heterojunction achieves remarkable 470% and 150% higher efficiency for the photocatalytic H2 evolution rate and photodegradation of rhodamine B, respectively. In particular, it is demonstrated that the charge transfer mechanism of SnO/TiO2 can be switched from the Z-scheme to type II by Pt loading, leading to a significant enhancement of photocatalytic performances. Furthermore, the photocatalytic H2 evolution activities of ZnO and C3N4 can also be improved by introducing SnO via simple mechanical mixing. This work provides not only a new versatile stimulant for enhancing photocatalytic activities but also in-depth understanding of the charge transfer mechanism of heterointerfaces of semiconductors.

Enhanced photocatalytic activity of Se-doped TiO2 under visible light irradiation

Anatase TiO₂ is a typical photocatalyst, and its excellent performance is limited in ultraviolet light range due to its wide band gap of 3.2 eV. A series of Se-doped TiO₂ nanoparticles in anatase structure with various Se concentrations up to 17.1 at.% were prepared using sol-gel method. The doped Se ions are confirmed to be mainly in the valence state of + 4, which provides extra electronic states in the band gap of TiO₂. The band gap is effectively narrowed with the smallest gap energy of 2.17 eV, and the photocatalytic activity is effectively improved due to the extended absorption range. The photocatalytic activity was evaluated by the degradation of Rhodamine B (RhB) in aqueous solution under visible light irradiation. The results show that Se doping significantly improves the photocatalytic activity of TiO₂ and 13.63 at.% Se-doped TiO₂ has the best performance.

The recent development of efficient Earth-abundant transition-metal nanocatalysts

Whereas noble metal compounds have long been central in catalysis, Earth-abundant metal-based catalysts have in the same time remained undeveloped. Yet the efficacy of Earth-abundant metal catalysts was already shown at the very beginning of the 20th century with the Fe-catalyzed Haber-Bosch process of ammonia synthesis and later in the Fischer-Tropsch reaction. Nanoscience has revolutionized the world of catalysis since it was observed that very small Au nanoparticles (NPs) and other noble metal NPs are extraordinarily efficient. Therefore the development of Earth-abundant metals NPs is more recent, but it has appeared necessary due to their "greenness". This review highlights catalysis by NPs of Earth-abundant transition metals that include Mn, Fe, Co, Ni, Cu, early transition metals (Ti, V, Cr, Zr, Nb and W) and their nanocomposites with emphasis on basic principles and literature reported during the last 5 years. A very large spectrum of catalytic reactions has been successfully disclosed, and catalysis has been examined for each metal starting with zero-valent metal NPs followed by oxides and other nanocomposites. The last section highlights the catalytic activities of bi- and trimetallic NPs. Indeed this later family is very promising and simultaneously benefits from increased stability, efficiency and selectivity, compared to monometallic NPs, due to synergistic substrate activation.

Enhanced photoreduction degradation of polybromodiphenyl ethers with Fe3O4-g-C3N4 under visible light irradiation

As typical persistent organic pollutants, polybrominated diphenyl ethers (PBDEs) have aroused high environmental concern due to their toxicity and recalcitrant degradation. Herein, we report the enhanced photoreduction degradation of polybromodiphenyl ethers with Fe₃O₄-g-C₃N₄ under visible light irradiation (>420 nm). A series of high activity photocatalysts Fe₃O₄-g-C₃N₄ (named FeOCN-x) have been synthesized by an in situ growth method. The characterization of the prepared FeOCN-x nanocomposites has been examined by SEM, TEM, ultraviolet-visible diffuse reflectance spectroscopy, a vibrating sample magnetometer, X-ray diffraction, X-ray photoelectron spectroscopy and Brunauer–Emmer–Teller surface area analysis. FeOCN-x hybrids all exhibit good magnetic separation properties with the saturation magnetization at 300 K varying from 0.4 to 6.3 emu g⁻¹. Under visible light irradiation, FeOCN-x hybrids show enhanced photocatalytic activity for the debromination of PBDEs compared with g-C₃N₄. Among all the hybrids, FeOCN-4 with a 4 wt% Fe₃O₄ content gives the highest reaction rate, which is 6.7 times as high as that in pure g-C₃N_4. The FeOCN-x nanocomposites not only exhibit good photostability, but could also be easily recovered by magnetism. The results of the kinetic isotope effects (KIE) and the trapping agent experiments show that the rate determining step in the degradation reaction of PBDEs with FeOCN-x is the rate of electron accumulation in the conductive band. A possible photoreductive mechanism has been proposed. This study shows that the easily magnetically separable recycled photocatalyst FeOCN-x, with high visible light activity, could be an excellent candidate for dealing with halogen pollutants.

The enhanced photoreduction degradation of polybrominated diphenyl ethers with magnetic separable Fe₃O₄-g-C₃N₄ under visible light irradiation is reported.

Metal-Free Photocatalyst with Visible-Light-Driven Post-Illumination Catalytic Memory

A novel metal-free photocatalyst with post-illumination catalytic memory was fabricated by the graphitic carbon nitride (g-C₃N₄), carbon nanotubes (CNTs), and graphene (Gr), in which g-C₃N₄ acts as an efficient photocatalyst and the CNTs and Gr act as supercapacitors. The removal of phenol was achieved in the dark by post-illumination catalytic memory because the photocatalyst could store a portion of its photoactivity via photogenerated electrons in the CNTs and Gr under visible-light illumination and then release the electrons again in the dark. Therefore, this metal-free photocatalyst is capable of operation in the dark for a broad range of applications.

Heterojunction Photocatalysts

Semiconductor-based photocatalysis attracts wide attention because of its ability to directly utilize solar energy for production of solar fuels, such as hydrogen and hydrocarbon fuels and for degradation of various pollutants. However, the efficiency of photocatalytic reactions remains low due to the fast electron-hole recombination and low light utilization. Therefore, enormous efforts have been undertaken to solve these problems. Particularly, properly engineered heterojunction photocatalysts are shown to be able to possess higher photocatalytic activity because of spatial separation of photogenerated electron-hole pairs. Here, the basic principles of various heterojunction photocatalysts are systematically discussed. Recent efforts toward the development of heterojunction photocatalysts for various photocatalytic applications are also presented and appraised. Finally, a brief summary and perspectives on the challenges and future directions in the area of heterojunction photocatalysts are also provided.

Highly Enhanced Photoreductive Degradation of Polybromodiphenyl Ethers with g-C3N4/TiO2 under Visible Light Irradiation

A series of high activity photocatalysts g-C₃N₄-TiO₂ were synthesized by simple one-pot thermal transformation method and characterized by transmission electron microscopy (TEM), scanning electron microscopy (SEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy, Brunauer–Emmett–Teller (BET) surface area, and ultraviolet–visible diffuse reflectance spectroscopy (UV-Vis-DRS). The g-C₃N₄-TiO₂ samples show highly improved photoreductive capability for the degradation of polybromodiphenyl ethers compared with g-C₃N₄ under visible light irradiation. Among all the hybrids, 0.02-C₃N₄-TiO₂ with 2 wt % g-C₃N₄ loaded shows the highest reaction rate, which is 15 times as high as that in bare g-C₃N₄. The well_-matched band gaps in heterojunction g-C₃N₄-TiO₂ not only strengthen the absorption intensity, but also show more effective charge carrier separation, which results in the highly enhanced photoreductive performance under visible light irradiation. The trapping experiments show that holetrapping agents largely affect the reaction rate. The rate of electron accumulation in the conductive band is the rate-determining step in the degradation reaction. A possible photoreductive mechanism has been proposed.

The recent development of efficient Earth-abundant transition-metal nanocatalysts

This review presents the recent remarkable developments of efficient Earth-abundant transition-metal nanocatalysts.

Synergetic effect of CuS@ZnS nanostructures on photocatalytic degradation of organic pollutant under visible light irradiation

Ultrafast visible light active CuS/ZnS nanostructured photocatalysts were synthesized by a hydrothermal method.

Charge Separation in TiO2/BDD Heterojunction Thin Film for Enhanced Photoelectrochemical Performance

Semiconductor photocatalysis driven by electron/hole has begun a new era in the field of solar energy conversion and storage. Here we report the fabrication and optimization of TiO2/BDD p-n heterojunction photoelectrode using p-type boron doped diamond (BDD) and n-type TiO2 which shows enhanced photoelectrochemical activity. A p-type BDD was first deposited on Si substrate by microwave plasma chemical vapor deposition (MPCVD) method and then n-type TiO2 was sputter coated on top of BDD grains for different durations. The microstructural studies reveal a uniform disposition of anatase TiO2 and its thickness can be tuned by varying the sputtering time. The formation of p-n heterojunction was confirmed through I-V measurement. A remarkable rectification property of 63773 at 5 V with very small leakage current indicates achieving a superior, uniform and precise p-n junction at TiO2 sputtering time of 90 min. This suitably formed p-n heterojunction electrode is found to show 1.6 fold higher photoelectrochemical activity than bare n-type TiO2 electrode at an applied potential of +1.5 V vs SHE. The enhanced photoelectrochemical performance of this TiO2/BDD electrode is ascribed to the injection of hole from p-type BDD to n-type TiO2, which increases carrier separation and thereby enhances the photoelectrochemical performance.

Facile fabrication of heterostructured cubic-CuFe2O4/ZnO nanofibers (c-CFZs) with enhanced visible-light photocatalytic activity and magnetic separation

Photocatalytic mechanism of a c-CuFe₂O₄/ZnO nanofibers (c-CFZs) p–n heterojunction.

ZnS/CuS nanotubes for visible light-driven photocatalytic hydrogen generation

ZnS/CuS nanotubes exhibit visible-light photocatalytic activity for H₂ evolution without cocatalysts, resulting from the heterojunctions between ZnS and CuS nanoparticles.

In situ synthesis of N-doped carbon nanotubes–BiOCl nanocomposites and their synergistic photocatalytic performance

N-Doped carbon nanotube–BiOCl (NCB) nanocomposites were prepared by an in situ growth strategy. The NCB nanocomposites possessed enhanced photocatalytic efficiency, compared with CN_xNTs, BiOCl 3D flower-like hierarchitectures, and P25.

Synthesis of Zn-doped In2O3nano sphere architectures as a triethylamine gas sensor and photocatalytic properties

Zn-doped In₂O₃nano spheres (ZIO NSs) were synthesized by calcining the precipitates prepared through a facile one-step hydrothermal synthesis method.

Synthesis of Carbon Nanotube-Nanotubular Titania Composites by Catalyst-Free CVD Process: Insights into the Formation Mechanism and Photocatalytic Properties

This work presents the synthesis of carbon nanotubes (CNTs) inside titania nanotube (TNTs) templates by a catalyst-free chemical vapor deposition (CVD) approach as composite platforms for photocatalytic applications. The nanotubular structure of TNTs prepared by electrochemical anodization provides a unique platform to grow CNTs with precisely controlled geometric features. The formation mechanism of carbon nanotubes inside nanotubular titania without using metal catalysts is explored and explained. The structural features, crystalline structures, and chemical composition of the resulting CNTs-TNTs composites were systematically characterized using scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Raman spectroscopy. The deposition time during CVD process was used to determine the formation mechanism of CNTs inside TNTs template. The photocatalytic properties of CNTs-TNTs composites were evaluated via the degradation of rhodamine B, an organic model molecule, in aqueous solution under mercury-xenon Hg (Xe) lamp irradiation monitored by UV-visible spectroscopy. The obtained results reveal that CNTs induces a synergestic effect on the photocatalytic activity of TNTs for rhodamine B degradation, opening new opportunities to develop advanced photocatalysts for environmental and energy applications.

Cobalt and sulfur co-doped nano-size TiO2 for photodegradation of various dyes and phenol

Various compositions of cobalt and sulfur co-doped titania nano-photocatalyst are synthesized via sol-gel method. A number of techniques including X-ray diffraction (XRD), ultraviolet-visible (UV-Vis), Rutherford backscattering spectrometry (RBS), thermal gravimetric analysis (TGA), Raman, N2 sorption, electron microscopy are used to examine composition, crystalline phase, morphology, distribution of dopants, surface area and optical properties of synthesized materials. The synthesized materials consisted of quasispherical nanoparticles of anatase phase exhibiting a high surface area and homogeneous distribution of dopants. Cobalt and sulfur co-doped titania demonstrated remarkable structural and optical properties leading to an efficient photocatalytic activity for degradation of dyes and phenol under visible light irradiations. Moreover, the effect of dye concentration, catalyst dose and pH on photodegradation behavior of environmental pollutants and recyclability of the catalyst is also examined to optimize the activity of nano-photocatalyst and gain a better understanding of the process.

Graphene-Based Photocatalysts for Solar-Fuel Generation

The production of solar fuel through photocatalytic water splitting and CO2 reduction using photocatalysts has attracted considerable attention owing to the global energy shortage and growing environmental problems. During the past few years, many studies have demonstrated that graphene can markedly enhance the efficiency of photocatalysts for solar-fuel generation because of its unique 2D conjugated structure and electronic properties. Herein we summarize the recent advances in the application of graphene-based photocatalysts for solar-fuel production, including CO2 reduction to hydrocarbon fuel and water splitting to H2. A brief overview of the fundamental principles for splitting of water and reduction of CO2 is given. The different roles of graphene in these graphene-based photocatalysts for improving photocatalytic performance are discussed. Finally, the perspectives on the challenges and opportunities for future research in this promising area are also presented.

Synthesis of novel Zn0.5Mg0.5Fe2O4@TiO2 nanotube arrays with enhanced photoelectrocatalytic properties

Zn_0.5Mg_0.5Fe₂O₄ nanoparticles contribute to widening of the spectral response range and reducing the charge recombination of TiO₂ nanotube arrays.

Zinc oxide based photocatalysis: tailoring surface-bulk structure and related interfacial charge carrier dynamics for better environmental applications

Surface-bulk modification of zinc oxide for efficient photocatalysis.