Membrane-based osmotic heat engine with organic solvent for enhanced power generation from low-grade heat

Thermally regenerative electrochemically cycled flow batteries with pH neutral electrolytes for harvesting low-grade heat

Harvesting waste heat with temperatures lower than 100 °C can improve the system efficiency and reduce greenhouse gas emissions, yet it has been a longstanding and challenging task. Electrochemical methods for harvesting low-grade heat have aroused research interest in recent years due to the relatively high effective temperature coefficient of the electrolytes (>1 mV K^-1) compared with the thermopower of traditional thermoelectric devices. Compared with other electrochemical devices such as the temperature-variation based thermally regenerative electrochemical cycle and temperature-difference based thermogalvanic cells, the thermally regenerative electrochemically cycled flow battery (TREC-FB) has the advantages of providing a continuous power output, decoupling the heat source and heat sink, and recuperating heat, and compatible with stacking for scaling up. However, the TREC-FB suffers from the issue of stable operation due to the challenge of pH matching between catholyte and anolyte solutions with desirable temperature coefficients. In this work, we demonstrate a pH-neutral TREC-FB based on KI/KI₃ and K₃Fe(CN)₆/K₄Fe(CN)₆ as the catholyte and anolyte, respectively, with a cell temperature coefficient of 1.9 mV K^-1 and a power density of 9 μW cm^-2. This work also presents a comprehensive model with a coupled analysis of mass transfer and reaction kinetics in a porous electrode that can accurately capture the flow rate dependence of the power density and energy conversion efficiency. We estimate that the efficiency of the pH-neutral TREC-FB can reach nearly 9% of the Carnot efficiency at the maximum power output with a temperature difference of 37 K. Via analysis, we identify that the mass transfer overpotential inside the porous electrode and the resistance of the ion exchange membrane are the two major factors limiting the efficiency and power density, pointing to directions for future improvements.

Thermal associated pressure-retarded osmosis processes for energy production: A review

Climate change is an existential threat to global environments and human life. To achieve global mean temperature rise of below 1.5 °C, increasing utilization of renewable energy and minimizing CO₂ emission from fossil fuel industries have been emphasized by the United Nations. Pressure-retarded osmosis (PRO) has displayed its technical feasibility in capturing renewable energy from the salinity gradient of two streams through a semipermeable membrane. Towards achieving economic feasible PRO, process optimization, waste stream/heat utilization, and hybrid PRO processes have been attempted by theoretically modelling and experimental examination. Among these efforts, the thermal associated PRO processes have received great attention due to their improved power generation. In this paper, we aim to provide a comprehensive review on thermal associated PRO processes, focusing on the role of thermal behaviour in both stand-alone PRO and hybrid PRO processes (e.g. PRO-membrane distillation, PRO-thermosiphon, PRO-solar pond). Meanwhile, thermal associated draw solution development has been highlighted. Finally, a combination of PRO with high temperature/high pressure geothermal waste gas as draw solution is proposed and its technical and economic feasibility is discussed, especially under Icelandic scenario.

Robust Membrane for Osmotic Energy Harvesting from Organic Solutions

Using particulate nanochannels for desired ions transport is a potential technology for nanofluidic osmotic energy harvesting. However, the finite fresh water as an essential part of this harvesting system limits its development. Therefore, developing a robust membrane for harvesting energy from other solutions such as waste organic solutions is attractive. Here, we develop bioinspired membrane based on boron nitride flakes and aramid nanofibers with nanochannels via a layer-by-layer assembly technique for harvesting nanofluidic energy from organic solutions directly. Enhancement of the synergistic effect of the boron nitride flakes and aramid nanofibers endows the aramid-boron nitride (ABN) membrane with a superstrong mechanical performance (360 MPa). The ABN membrane showed a pressured-induced current in LiCl-methanol solution and NaCl-ethanol solution, respectively. More importantly, the ABN membrane exhibited outstanding stable and high-energy harvesting with salinity gradient dependence in LiCl-methanol, LiCl-ethanol, and NaCl-ethanol solutions, respectively. Impressively, the voltage produced from the organic solutions (LiCl-methanol, C_h/C_l = 1000) can power the transistor and it works well for 1 h as a gate voltage. The design of bioinspired membrane enables a robust and efficient harvesting of osmotic energy from organic solutions.

The Power and Efficiency Analyses of the Cylindrical Cavity Receiver on the Solar Stirling Engine

The technique of solar dish and Stirling engine combination is the most challenging and promising one. For the efficient conversion of the externally concentrated heat to the usable power, we studied the influences of the wall temperature, inclination angle, and open area ratio of the receiver on the Stirling engine power and efficiency. The theoretical analysis of the heat exchange element of the solar Stirling engine was performed, and the simulation model of the cavity absorber was built and analyzed. The temperature cloud and heat loss trends of the receiver under different wall temperatures, inclination angles, and opening ratios were illustrated. When the wall temperature of the absorber changes from 700 to 1000 K, the efficiency of the engine has increased by 8.8% from 21.34% to 30.11%. The higher the temperature, the higher the efficiency. As the inclination angle of the absorber increases from 0° to 60°, the efficiency of the engine is increased by 7.7% from 21.1% to 28.8%. With the increases of the aperture ratio, the engine output and efficiency reduced. The engine efficiency at the aperture ratio of 0.5 is 4% larger than that at the aperture ratio of 1.

Low-Grade Waste Heat Recovery via an Osmotic Heat Engine by Using a Freestanding Graphene Oxide Membrane

The osmotic heat engine represents a new and promising technology for the harvesting of low-grade waste heat from various sources. However, the lack of an adequate semipermeable membrane hinders the technology's advancement. In this study, we investigated the application of a freestanding graphene oxide membrane (GOM) for energy generation in an osmotic heat engine. The synthesized GOM has a water permeability coefficient of 4.4 L m^-2 h^-1 bar^-1 (LMH-bar). The internal concentration polarization in the osmosis filtration system can be minimized because no membrane support layer is needed for the freestanding GOM. As a result, high water flux and high power density are obtained. For example, under an applied hydraulic pressure of 6.90 bar, with a 2 M draw solution of ammonium bicarbonate solution, a power density of 20.0 W/m² is achieved. This study shows that the freestanding GOM is promising for application in the osmotic heat engine. Future research regarding improving the mechanical properties and water stability of the GOM is beneficial for further advancing the technology.

Salinity Gradients for Sustainable Energy: Primer, Progress, and Prospects

Combining two solutions of different composition releases the Gibbs free energy of mixing. By using engineered processes to control the mixing, chemical energy stored in salinity gradients can be harnessed for useful work. In this critical review, we present an overview of the current progress in salinity gradient power generation, discuss the prospects and challenges of the foremost technologies - pressure retarded osmosis (PRO), reverse electrodialysis (RED), and capacitive mixing (CapMix) and provide perspectives on the outlook of salinity gradient power generation. Momentous strides have been made in technical development of salinity gradient technologies and field demonstrations with natural and anthropogenic salinity gradients (for example, seawater-river water and desalination brine-wastewater, respectively), but fouling persists to be a pivotal operational challenge that can significantly ebb away cost-competitiveness. Natural hypersaline sources (e.g., hypersaline lakes and salt domes) can achieve greater concentration difference and, thus, offer opportunities to overcome some of the limitations inherent to seawater-river water. Technological advances needed to fully exploit the larger salinity gradients are identified. While seawater desalination brine is a seemingly attractive high salinity anthropogenic stream that is otherwise wasted, actual feasibility hinges on the appropriate pairing with a suitable low salinity stream. Engineered solutions are foulant-free and can be thermally regenerative for application in low-temperature heat utilization. Alternatively, PRO, RED, and CapMix can be coupled with their analog separation process (reverse osmosis, electrodialysis, and capacitive deionization, respectively) in salinity gradient flow batteries for energy storage in chemical potential of the engineered solutions. Rigorous techno-economic assessments can more clearly identify the prospects of low-grade heat conversion and large-scale energy storage. While research attention is squarely focused on efficiency and power improvements, efforts to mitigate fouling and lower membrane and electrode cost will be equally important to reduce levelized cost of salinity gradient energy production and, thus, boost PRO, RED, and CapMix power generation to be competitive with other renewable technologies. Cognizance of the recent key developments and technical progress on the different technological fronts can help steer the strategic advancement of salinity gradient as a sustainable energy source.

Engineering Surface Energy and Nanostructure of Microporous Films for Expanded Membrane Distillation Applications

We investigated the factors that determine surface omniphobicity of microporous membranes and evaluated the potential application of these membranes in desalination of low surface tension wastewaters by membrane distillation (MD). Specifically, the effects of surface morphology and surface energy on membrane surface omniphobicity were systematically investigated by evaluating wetting resistance to low surface tension liquids. Single and multilevel re-entrant structures were achieved by using cylindrical glass fibers as a membrane substrate and grafting silica nanoparticles (SiNPs) on the fibers. Surface energy of the membrane was tuned by functionalizing the fiber substrate with fluoroalkylsilane (FAS) having two different lengths of fluoroalkyl chains. Results show that surface omniphobicity of the modified fibrous membrane increased with higher level of re-entrant structure and with lower surface energy. The secondary re-entrant structure achieved by SiNP coating on the cylindrical fibers was found to play a critical role in enhancing the surface omniphobicity. Membranes coated with SiNPs and chemically modified by the FAS with a longer fluoroalkyl chain (or lower surface energy) exhibited excellent surface omniphobicity and showed wetting resistance to low surface tension liquids such as ethanol (22.1 mN m(-1)). We further evaluated performance of the membranes in desalination of saline feed solutions with varying surface tensions by membrane distillation (MD). The engineered membranes exhibited stable MD performance with low surface tension feed waters, demonstrating the potential application omniphobic membranes in desalinating complex, high salinity industrial wastewaters.