Patterning Phase Separation in Polymer Films with Dip-Pen Nanolithography

Directed ordering of phase separated domains and dewetting of thin polymer blend films on a topographically patterned substrate

Substrate pattern guided self-organization of ultrathin and confined polymeric films on a topographically patterned substrate is a useful approach for obtaining ordered meso and nano structures over large areas, particularly if the ordering is achieved during film preparation itself, eliminating any post-processing such as thermal or solvent vapor annealing. By casting a dilute solution of two immiscible polymers, polystyrene (PS) and polymethylmethacrylate (PMMA), from a common solvent (toluene) on a topographically patterned substrate with a grating geometry, we show the formation of self-organized meso patterns with various degrees of ordering. The morphology depends on both the concentration of the dispensed solution (C_n) and the blend composition (R_B). Depending on the extent of dewetting during spin coating, the final morphologies can be classified into three distinct categories. At a very low C_n the solution dewets fully, resulting in isolated polymer droplets aligned along substrate grooves (Type 1). Type 2 structures comprising isolated threads with aligned phase separated domains along each substrate groove are observed at intermediate C_n. A continuous film (Type 3) is obtained above a critical concentration (C_n*) that depends on R_B. While the extent of ordering of the domains gradually diminishes with an increase in film thickness for Type 3 patterns, the size of the domains remains much smaller than that on a flat substrate, resulting in significant downsizing of the features due to the lateral confinement imposed on the phase separation process by the topographic patterns. Finally, we show that some of these structures exhibit excellent broadband anti-reflection (AR) properties.

Thermally induced phase separation in levitated polymer droplets

We report thermally induced rapid phase separation in PS/PVME polymer blends using a unique contact free droplet based architecture. De-mixing of homogeneous blends due to inter component dynamic asymmetry is aggravated by the externally supplied heat. Separation of polymer blends is usually investigated in the bulk which is a tedious process and requires several hours for completion. Alternatively, separation in droplet configuration reduces the process timescale by about 3-5 orders due to a constrained micron-sized domain [fast processing and high throughput] while maintaining similar separation morphologies as in the bulk. We observed the effect of heating rates on the phase separation length and timescales. Furthermore, the separation length scale can be precisely controlled across one order by simply tuning the heating rate. The methodology can be scaled up for applications ranging from surface patterning to pharmaceutics.

Enhanced solid-state order and field-effect hole mobility through control of nanoscale polymer aggregation

Efficient charge carrier transport in organic field-effect transistors (OFETs) often requires thin films that display long-range order and close π-π packing that is oriented in-plane with the substrate. Although some polymers have achieved high field-effect mobility with such solid-state properties, there are currently few general strategies for controlling the orientation of π-stacking within polymer films. In order to probe structural effects on polymer-packing alignment, furan-containing diketopyrrolopyrrole (DPP) polymers with similar optoelectronic properties were synthesized with either linear hexadecyl or branched 2-butyloctyl side chains. Differences in polymer solubility were observed and attributed to variation in side-chain shape and polymer backbone curvature. Averaged field-effect hole mobilities of the polymers range from 0.19 to 1.82 cm(2)/V·s, where PDPP3F-C16 is the least soluble polymer and provides the highest maximum mobility of 2.25 cm(2)/V·s. Analysis of the films by AFM and GIXD reveal that less soluble polymers with linear side chains exhibit larger crystalline domains, pack considerably more closely, and align with a greater preference for in-plane π-π packing. Characterization of the polymer solutions prior to spin-coating shows a correlation between early onset nanoscale aggregation and the formation of films with highly oriented in-plane π-stacking. This effect is further observed when nonsolvent is added to PDPP3F-BO solutions to induce aggregation, which results in films with increased nanostructural order, in-plane π-π orientation, and field-effect hole mobilities. Since nearly all π-conjugated materials may be coaxed to aggregate, this strategy for enhancing solid-state properties and OFET performance has applicability to a wide variety of organic electronic materials.

Directed assembly of P3HT:PCBM blend films using a chemical template with sub-300 nm features

Surface energy has been demonstrated as a means to direct interfacial-layer composition in polymer:fullerene blends utilized as active layers in organic photovoltaic devices. Combined with recent materials advances in the preparation of nanoscale chemical patterns, surface energy control of nanophase separation presents an opportunity to employ patterned surface energy templates to control the 3D blend morphology of polymer:fullerene blends. This report details the directed assembly of poly(3-hexylthiophene):phenyl-C61-butyric acid methyl ester (P3HT:PCBM) blends atop linear grating patterns with domains of alternating high and low surface energy of 50 to 600 nm in width prepared by nanoscale oxidative lithography of alkyl-terminated self-assembled monolayers on SiO2 and SiH surfaces. Tapping-, contact-, and current-sensing AFM studies demonstrated that chemical patterns were effective at directing the 3D morphology of P3HT:PCBM blends at dimensions of >200 nm. As the dimensionality of domains approached 100 nm, the chemical patterns were no longer able to direct phase segregation, evidence that a directed spinodal decomposition mechanism was responsible for the observed morphology. Surprisingly, the low surface energy component (P3HT) was found to be atop the high surface energy domains of the template, in conflict with current understanding of the role of surface energy directed assembly in polymer blends. These results suggest that the directed spinodal decomposition mechanism applies to conjugated polymer:fullerene blends, but that additional parameters unique to these types of systems will require refinement of the theory to adequately describe and predict the behavior of these scientifically and industrially interesting materials.

Spectroscopic imaging of photopotentials and photoinduced potential fluctuations in a bulk heterojunction solar cell film

We present spatially resolved photovoltage spectra of a bulk heterojunction solar cell film composed of phase-separated poly(9,9'-dioctylfluorene-co-benzothiadiazole) (F8BT) and poly(9,9'-dioctylfluorene-co-bis-N,N'-(4-butylphenyl)-bis-N,N'-phenyl-1,4-phenylenediamine) (PFB) polymers prepared on ITO/PEDOT:PSS and aluminum substrates. Over both PFB- and F8BT-rich domains, the photopotential spectra were found to be proportional to a linear combination of the polymers' absorption spectra. Charge trapping in the film was studied using photopotential fluctuation spectroscopy, in which low-frequency photoinduced electrostatic potential fluctuations were measured by observing noise in the oscillation frequency of a nearby charged atomic force microscope cantilever. Over both F8BT- and PFB-rich regions, the magnitude, distance dependence, frequency dependence, and illumination wavelength dependence of the observed cantilever frequency noise are consistent with photopotential fluctuations arising from stochastic light-driven trapping and detrapping of charges in F8BT. Taken together, our findings suggest a microscopic mechanism by which intermixing of phases leads to charge trapping and thereby to suppressed open-circuit voltage and decreased efficiency in this prototypical bulk heterojunction solar cell film.

Precise pattern replication of polymer blends into nonuniform geometries via reducing interfacial tension between two polymers

Patterned polymer structures with different functionalities have many potential applications. Directed assembly of polymer blends using chemically functionalized patterns during spin-coating has been used to fabricate the patterned polymer structures. For bridging the gap between laboratorial experiments and manufacturing of nanodevices, the polymer blends structures are required to be precisely patterned into nonuniform geometries in a high-rate process, which still is a challenge. In this Article, we demonstrated for the first time that by decreasing the interfacial tension between two polymers polystyrene and poly(acrylic acid) via adding a compatibilizer (polystyrene-b-poly(acrylic acid) ), a polystyrene/poly(acrylic acid) blend was precisely patterned into nonuniform geometries in a high-rate fashion. The patterned nonuniform geometries included angled lines with angles varied from 30° to 150°, T-junctions, square arrays, circle arrays, and arbitrary letter-shaped geometries. The reduction in the interfacial tension improved the line edge roughness and the patterning efficiency of the patterned polymer blends. In addition, the commensurability between characteristic length and pattern periodicity for well-ordered morphologies was also expanded with decreasing interfacial tension. This approach can be easily extended to other functional polymers in a blend and facilitate the applications of patterned polymer structures in biosensors, organic thin-film electronics, and polymer solar cells.

Spatially modulating interfacial properties of transparent conductive oxides: patterning work function with phosphonic Acid self-assembled monolayers

The interface between an organic semiconductor and a transparent conducting oxide is crucial to the performance of organic optoelectronics. We use microcontact printing to pattern pentafluorobenzyl phosphonic acid self-assembled monolayers (SAMs) on indium tin oxide (ITO). We obtain high-fidelity patterns with sharply defined edges and with large work function contrast (comparable to that obtained from phosphonic acid SAMs deposited from solution).

Preparation and microcosmic structural analysis of recording coating on inkjet printing media

Preparation of recording coating on inkjet printing (RC-IJP) media was proposed. The microstructure and roughness of RC-IJP was analyzed by scanning electron microscopy (SEM) and atomic force microscope (AFM). The surface infiltration process of RC-IJP was studied by a liquid infiltration instrument. The distribution of C, O and Si composites on recording coating surface is analyzed by energy dispersive spectrum (EDS). The transmission electron microscopy (TEM) analysis showed that the nanoscale silica could be dissolved uniformly in water. Finally, the print color is shown clearly by the preparative recording coating.

Chemically functionalized surface patterning

Patterning substrates with versatile chemical functionalities from micro- to nanometer scale is a long-standing and interesting topic. This review provides an overview of a range of techniques commonly used for surface patterning. The first section briefly introduces conventional micropatterning tools, such as photolithography and microcontact printing. The second section focuses on the currently used nanolithographic techniques, for example, scanning probe lithography (SPL), and their applications in surface patterning. Their advantages and disadvantages are also demonstrated. In the last section, dip-pen nanolithography (DPN) is emphatically illustrated, with a particular stress on the patterning and applications of biomolecules.

Ordered polymeric microhole array made by selective wetting and applications for electrochemical microelectrode array

In this paper, we report the microelectrode array fabrication using selective wetting/dewetting of polymers on a chemical pattern which is a simple and convenient method capable of creating negative polymeric replicas using polyethylene glycol (PEG) as a clean and nontoxic sacrificial layer. The fabricated hole-patterned polypropylene film on gold demonstrated enhanced electrochemical properties. The chemical pattern is fabricated by microcontact printing using octadecanethiol (ODT) as an ink on gold substrate. When PEG is spin-cast on the chemical pattern, PEG solution selectively dewets the ODT patterned areas and wets the remaining bare gold areas, leading to the formation of arrayed PEG dots. A negative replicas of the PEG dot array is obtained by spin-coating of polypropylene (PP) solution in hexane which preferentially interacts with the hydrophobic ODT region on the patterned gold surface. The arrayed PEG dots are not affected the during PP spin-coating step because of their intrinsic immiscibility. Consequently, the hole-patterned PP film is obtained after PEG removal. The electrochemical signal of the PP film demonstrates the negligible leakage current by high dielectric and self-healing of defects on the chemical pattern by the polymer. This method is applicable to fabrication of microelectrode arrays and possibly can be employed to fabricate a variety of functional polymeric structures, such as photomasks, arrays of biomolecules, cell arrays, and arrays of nanomaterials.

Surface characterization of polythiophene:fullerene blends on different electrodes using near edge X-ray absorption fine structure

We study the top surface composition of blends of the conjugated polymer regioregular poly-3-hexylthiophene (P3HT) with the fullerene (6,6)-phenyl-C(61)-butyric acid methyl ester (PCBM), an important model system for organic photovoltaics (OPVs), using near-edge X-ray absorption fine structure spectroscopy (NEXAFS). We compare the ratio of P3HT to PCBM near the air/film interface that results from preparing blend films on two sets of substrates: (1) poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS) coated indium tin oxide (ITO) as is commonly used in conventional OPV structures and (2) ZnO substrates that are either unmodified or modified with a C(60)-like self-assembled monolayer, similar to those that have been recently reported in inverted OPV structures. We find that the top surface (the film/air interface) is enriched in P3HT compared to the bulk, regardless of substrate or annealing conditions, indicating that changes in device performance due to substrate modification treatments should be attributed to the buried substrate/film interface and the bulk of the film rather than the exposed film/air interface.

Biomimetic nanopatterns as enabling tools for analysis and control of live cells

It is becoming increasingly evident that cell biology research can be considerably advanced through the use of bioengineered tools enabled by nanoscale technologies. Recent advances in nanopatterning techniques pave the way for engineering biomaterial surfaces that control cellular interactions from the nano- to the microscale, allowing more precise quantitative experimentation capturing multi-scale aspects of complex tissue physiology in vitro. The spatially and temporally controlled display of extracellular signaling cues on nanopatterned surfaces (e. g., cues in the form of chemical ligands, controlled stiffness, texture, etc.) that can now be achieved on biologically relevant length scales is particularly attractive enabling experimental platform for investigating fundamental mechanisms of adhesion-mediated cell signaling. Here, we present an overview of bio-nanopatterning methods, with the particular focus on the recent advances on the use of nanofabrication techniques as enabling tools for studying the effects of cell adhesion and signaling on cell function. We also highlight the impact of nanoscale engineering in controlling cell-material interfaces, which can have profound implications for future development of tissue engineering and regenerative medicine.

Engineering 3D ordered molecular thin films by nanoscale control

This perspective aims to report on experimental preparation and investigation tools for engineering molecular thin films with a three-dimensional (3D) nanoscale control that is of relevant interest for different emerging applications as well as for the development of calibration standards. Such thin films may be obtained by man-made methods, self-assembly or spatio-temporal self-organization and/or by the combination of these last approaches with external tools. Understanding the main features and the physical-chemistry underlying the related ordering phenomena is in due course and a theoretical framework is under development. In this respect it is of fundamental importance to achieve the ability to get 3D structural images with a nanoscale detail. This issue is at the early stage and novel techniques like electron tomography and scanning transmission X-ray microscopy are very promising.

Heterogeneity in polymer solar cells: local morphology and performance in organic photovoltaics studied with scanning probe microscopy

The use of organic photovoltaics (OPVs) could reduce production costs for solar cells because these materials are solution processable and can be manufactured by roll-to-roll printing. The nanoscale texture, or film morphology, of the donor/acceptor blends used in most OPVs is a critical variable that can dominate both the performance of new materials being optimized in the lab and efforts to move from laboratory-scale to factory-scale production. Although efficiencies of organic solar cells have improved significantly in recent years, progress in morphology optimization still occurs largely by trial and error, in part because much of our basic understanding of how nanoscale morphology affects the optoelectronic properties of these heterogeneous organic semiconductor films has to be inferred indirectly from macroscopic measurements. In this Account, we review the importance of nanoscale morphology in organic semiconductors and the use of electrical scanning probe microscopy techniques to directly probe the local optoelectronic properties of OPV devices. We have observed local heterogeneity of electronic properties and performance in a wide range of systems, including model polymer-fullerene blends such as poly(3-hexylthiophene) (P3HT) and [6,6]-phenyl-C(61)-butyric acid methyl ester (PCBM), newer polyfluorene copolymer-PCBM blends, and even all polymer donor-acceptor blends. The observed heterogeneity in local photocurrent poses important questions, chiefly what information is contained and what is lost when using average values obtained from conventional measurements on macroscopic devices and bulk samples? We show that in many cases OPVs are best thought of as a collection of nanoscopic photodiodes connected in parallel, each with their own morphological and therefore electronic and optical properties. This local heterogeneity forces us to carefully consider the adequacy of describing OPVs solely by "average" properties such as the bulk carrier mobility. Characterizing this local heterogeneity in the morphology of an OPV and the consequent variations in local performance is vital to understanding OPV operation.

Temperature controlled dip-pen nanolithography

Dip-pen nanolithography (DPN) has emerged as a powerful tool for creating sophisticated micron- and nanoscale features of various molecules, such as small organic molecules, on a variety of substrates. Despite significant advances in recent years, the influence of temperature on molecular transport for nanostructure fabrication has not been fully explored. Herein, it is shown how the dimensions of patterned organic nanostructures can be controlled by using a cooling/heating module. This method allows nanometer-sized feature fabrication of a variety of small organic molecules, including 'inks' that have been deemed very difficult to write under ambient conditions. Features with dimensions as small as 30 nm have been successfully reproduced using the newly developed temperature control device in conjunction with DPN.

Uniform patterning of sub-50-nm-scale Au nanostructures on insulating solid substrate via dip-pen nanolithography

We report a direct deposition strategy for sub-50-nm-scale uniform Au patterns on virtually any general insulating substrate via dip-pen nanolithography (DPN). In that process, HAuCl(4) molecules were deposited onto bare insulating substrates via a molecular diffusion process, in the absence of electrochemical reactions. Subsequently, the generated HAuCl(4) molecular patterns were decomposed to leave Au-only patterns using a thermal annealing process. Uniform Au patterns with a mean diameter of 47.9 +/- 3.1 nm were achieved after the annealing process. The strategy allowed us to generate Au patterns on virtually any general insulating substrate (e.g., SiO(2), Al(2)O(3), polyimide, etc) without the need for surface functionalization or additional electrode structures. This versatile and reliable patterning method is expected to be useful in the future development of various novel industrial applications (e.g., mask or nanocircuit repair, nanosensors, etc.).

Imaging the evolution of nanoscale photocurrent collection and transport networks during annealing of polythiophene/fullerene solar cells

We use photoconductive atomic force microscopy to image nanoscale spatial variations in photocurrent across the surfaces of photovoltaic cells made from blends of the conjugated polymer regioregular poly(3-hexylthiopene) (P3HT) with phenyl-C(61)-butyric acid methyl ester (PCBM). We study how the spatial variations in photocurrent evolve with thermal annealing, and we correlate these changes with the evolution of macroscopic film and device properties such as external quantum efficiency and carrier mobility. We use conductive atomic force microscopy to examine the development of injection and transport networks for both electrons and holes as a function of annealing. We find that the hole transport, electron transport, and photocurrent collection networks become increasingly heterogeneous with thermal annealing and remain heterogeneous on the 10-100 nm length scale even in the most efficient P3HT/PCBM devices. After annealing, the regions of the greatest dark hole currents, greatest dark electron currents, and greatest photocurrents are each associated with different regions of the nanostructured films. These results suggest spatial heterogeneity can contribute to the imperfect internal quantum efficiency even in relatively efficient organic photovoltaics and that fully 3D modeling is needed to describe the devices physics of polymer blend solar cells.

Controlling film morphology in conjugated polymer:fullerene blends with surface patterning

We study the effects of patterned surface chemistry on the microscale and nanoscale morphology of solution-processed donor/acceptor polymer-blend films. Focusing on combinations of interest in polymer solar cells, we demonstrate that patterned surface chemistry can be used to tailor the film morphology of blends of semiconducting polymers such as poly-[2-(3,7-dimethyloctyloxy)-5-methoxy-p-phenylenevinylene] (MDMO-PPV), poly-3-hexylthiophene (P3HT), poly[(9,9-dioctylflorenyl-2,7-diyl)-co-benzothiadiazole)] (F8BT), and poly(9,9-dioctylfluorene-co-bis-N,N'-(4-butylphenyl)-bis-N,N'-phenyl-1,4-phenylendiamine) (PFB) with the fullerene derivative, [6,6]-phenyl-C(61)-butyric acid methyl ester (PCBM). We present a method for generating patterned, fullerene-terminated monolayers on gold surfaces and use microcontact printing and Dip-Pen Nanolithography (DPN) to pattern alkanethiols with both micro- and nanoscale features. After patterning with fullerenes and other functional groups, we backfill the rest of the surface with a variety of thiols to prepare substrates with periodic variations in surface chemistry. Spin coating polymer:PCBM films onto these substrates, followed by thermal annealing under nitrogen, leads to the formation of structured polymer films. We characterize these films with Atomic Force Microscopy (AFM), Raman spectroscopy, and fluorescence microscopy. The surface patterns are effective in guiding phase separation in all of the polymer:PCBM systems investigated and lead to a rich variety of film morphologies that are inaccessible with unpatterned substrates. We demonstrate our ability to guide pattern formation in films thick enough to be of interest for actual device applications (up to 200 nm in thickness) using feature sizes as small as 100 nm. Finally, we show that the surface chemistry can lead to variations in film morphology on length scales significantly smaller than those used in generating the original surface patterns. The variety of behaviors observed and the wide range of control over polymer morphology achieved at a variety of different length scales have important implications for the development of bulk heterojunction solar cells.

The role of mesoscopic PCBM crystallites in solvent vapor annealed copolymer solar cells

Solution processable methanofullerene-based solar cells are the most widely studied class of organic photovoltaics (OPVs). The evolution of the electronic properties with solvent vapor annealing (SVA) in polyfluorene-copolymer and [6,6]phenyl-C61-butyric acid methyl ester (PCBM) blended OPVs is studied using various scanning probe techniques: light beam induced current spectroscopy (LBIC), conductive atomic force microscopy (c-AFM), and photoconductive AFM (pc-AFM). We demonstrate that SVA improves the power conversion efficiency by 40% while forming mesoscopic PCBM crystallites and a approximately 3 nm copolymer-rich overlayer at the cathode interface. We find that the large crystallites created during annealing do not directly improve the local performance of the device, but instead attribute the performance improvement to the ripened blend morphology and an increase in the hole mobility of the copolymer in comparison to the unannealed blend. The PCBM-rich aggregates act as a sink for excess PCBM, although excess PCBM is initially required to form the appropriate structural features prior to the annealing process.

Formation of regular structures in the process of phase separation

Phase separation under directional quenching has been studied in a Cahn-Hilliard model. In distinct contrast to the disordered patterns which develop under a homogeneous quench, periodic stripe patterns are generated behind the quench front. Their wavelength is uniquely defined by the velocity of the quench interface in a wide range. Numerical simulations match perfectly analytical results obtained in the limit of small and large velocities of the quench interface. Additional periodic modulation of the quench interface may lead to cellular patterns. The quenching protocols analyzed are expected to be an effective tool in technological applications to design nanostructured materials.

Space charge limited current measurements on conjugated polymer films using conductive atomic force microscopy

We describe local (~150 nm resolution), quantitative measurements of charge carrier mobility in conjugated polymer films that are commonly used in thin-film transistors and nanostructured solar cells. We measure space charge limited currents (SCLC) through these films using conductive atomic force microscopy (c-AFM) and in macroscopic diodes. The current densities we measure with c-AFM are substantially higher than those observed in planar devices at the same bias. This leads to an overestimation of carrier mobility by up to 3 orders of magnitude when using the standard Mott-Gurney law to fit the c-AFM data. We reconcile this apparent discrepancy between c-AFM and planar device measurements by accounting for the proper tip-sample geometry using finite element simulations of tip-sample currents. We show that a semiempirical scaling factor based on the ratio of the tip contact area diameter to the sample thickness can be used to correct c-AFM current-voltage curves and thus extract mobilities that are in good agreement with values measured in the conventional planar device geometry.

Selective assembly and guiding of actomyosin using carbon nanotube network monolayer patterns

We report a new method for the selective assembly and guiding of actomyosin using carbon nanotube patterns. In this method, monolayer patterns of the single-walled carbon nanotube (swCNT) network were prepared via the self-limiting mechanism during the directed assembly process, and they were used to block the adsorption of both myosin and actin filaments on specific substrate regions. The swCNT network patterns were also used as an efficient barrier for the guiding experiments of actomyosin. This is the first result showing that inorganic nanostructures such as carbon nanotubes can be used to control the adsorption and activity of actomyosin. This strategy is advantageous over previous methods because it does not require complicated biomolecular linking processes and nonbiological nanostructures are usually more stable than biomolecular linkers.

Mapping local photocurrents in polymer/fullerene solar cells with photoconductive atomic force microscopy

The performance of organic solar cells is highly dependent on film morphology. However, directly correlating local film structures with device performance remains challenging. We demonstrate that photoconductive atomic force microscopy (pcAFM) can be used to map local photocurrents with 20 nm resolution in donor/acceptor blend solar cells of the conjugated polymer poly[2-methoxy-5-(3',7'-dimethyloctyl-oxy)-1,4-phenylene vinylene] (MDMO-PPV) with the fullerene (6,6)-phenyl-C61-butyric acid methyl ester (PCBM) spin-coated from various solvents. We present photocurrent maps under short-circuit conditions (zero applied bias) as well as under various applied voltages. We find significant variation in the short-circuit current between regions that appear identical in AFM topography. These variations occur from one domain to another as well as on larger length scales incorporating multiple domains. These results suggest that the performance of polymer-fullerene blends can still be improved through better control of morphology.

Applications of dip-pen nanolithography

The ability to tailor the chemical composition and structure of a surface at the sub-100-nm length scale is important for studying topics ranging from molecular electronics to materials assembly, and for investigating biological recognition at the single biomolecule level. Dip-pen nanolithography (DPN) is a scanning probe microscopy-based nanofabrication technique that uniquely combines direct-write soft-matter compatibility with the high resolution and registry of atomic force microscopy (AFM), which makes it a powerful tool for depositing soft and hard materials, in the form of stable and functional architectures, on a variety of surfaces. The technology is accessible to any researcher who can operate an AFM instrument and is now used by more than 200 laboratories throughout the world. This article introduces DPN and reviews the rapid growth of the field of DPN-enabled research and applications over the past several years.

Relative humidity effects in dip-pen nanolithography of alkanethiol mixtures

In the dip-pen nanolithography of a binary alkanethiol mixture of mercaptohexadecanoic acid (MHA) and 1-octadecanethiol (ODT) at a relative humidity (RH) of less than 80%, two distinct phases of MHA and ODT were patterned. However, on ramping up the RH to greater than 80%, only MHA was observed to pattern. This effect was reversible, as shown by the fact that two distinct thiol regions were again patterned on lowering the RH. This segregation could be exploited for generating exclusive MHA (hydrophilic) templates for subsequent architectures from a mixture of alkanethiols driven solely by the RH.