Highly selective optical fluoride ion sensor with submicromolar detection limit based on aluminum(III) octaethylporphyrin in thin polymeric film

Near-Infrared Fluoride Sensing Nano-Optodes and Distance-Based Hydrogels Containing Aluminum-Phthalocyanine

Fluoride ions are highly relevant in environmental and biological sciences, and there is a very limited number of established fluoride chemical sensors. Previous fluoride-selective optodes were demonstrated with metal-porphyrin as the ionophore and required a chromoionophore for optical signal transduction. We demonstrate here novel optical fluoride sensing with nano-optodes containing an aluminum-phthalocyanine complex (AlClPc) as the single active sensing component, simplifying the conventional ion-selective optodes approach. The fluoride nano-optodes were interrogated in the absorbance and fluorescence modes in the near-infrared region, with absorption around 725 nm and emission peaks at 720 and 800 nm, respectively. The nano-optodes exhibited a lower detection limit around 0.1 μM and good selectivity over a range of common anions including ClO4-, Cl-, Br-, I-, SO42-, NO3-, and AcO-. Furthermore, the nano-optodes were physically entrapped in agarose hydrogels to allow distance-based point-of-care testing (POCT) applications. The 3D networks of the agarose hydrogel were able to filter off large particulates in the samples without stopping fluoride ions to reach the nano-optodes. The fluoride concentrations in real samples including river water, mineral water, and groundwater were successfully determined with the distance-based sensing hydrogel, and the results agreed well with those from commercial fluoride electrodes. Therefore, the results in this work lay the groundwork for the optical detection of fluoride in environmental samples without very sophisticated sample manipulation.

Development of ratiometric fluorescent probes based on peptides for sensing Pb2+ in aquatic environments and human serum

The detection of Pb²⁺ ions in aquatic environments and biofluid samples is crucial for assessment of human health. Herein, we synthesized two fluorescent probes (1 and 2) consisting of the peptide receptor for Pb²⁺ and a benzothiazolyl-cyanovinylene fluorophore that exhibited excimer-like emission when it aggregated. The peptide-based probes sensitively detected Pb²⁺ in purely aqueous solution (1% DMF) through ratiometric fluorescent response with a decrease in monomer emission at 520 nm and an increase in excimer emission at 570 nm. Specially, probe 2 showed remarkable detection features such as high selectivity for Pb²⁺over 15 metal ions, high binding affinity (K_d = 5.83 × 10^-7 M) for Pb²⁺, significant emission intensity changes, low detection limit (3.8 nM) of Pb²⁺, high water solubility, and visible light excitation (450 nm). Probe 2 was successfully used to quantify nanomolar concentration (0 ∼ 800 nM) of Pb²⁺ in real water samples (ground water and tap water). Specially, 2 was successfully applied for the quantification of Pb²⁺ in human serum by combination of microwave-assisted human serum digestion and filtration of digested serum by anion exchange cartridge. We clearly investigated the binding mode of 2 with Pb²⁺ using ¹H NMR, IR spectroscopy, pH titration, confocal microscopy, and size analysis. The peptide-based fluorescent probe might have great application potential for sensing Pb²⁺ in aquatic environments and biofluid samples.

Novel (E)−2-((1-(thiophen-2-yl)ethylidene)-amino) phenol Manganese(II) as an Ionophore Based on Thiocyanate-Selective Electrodes and Its Applications

Novel highly selective potentiometric sensor based on aquadichloro(E)−2-((1-(thiophen-2-yl)ethylidene)-amino)phenol manganese(II)trihydrate as an anion carrier. The thiocayanate electrode displayed a very high selectivity compared with others inorganic anions. Different sensors with plasticized PVC membranes have been investigated. The sensors construction containing different amounts of ionophore with and without additives. The pH over 3.5–6.5 range has been studied. Optimized membrane electrode included 66 mg PVC, 132 mg o-nitrophenyloctylether, 10 mol % tetrakis(trifluoromethyl)phenyl borate and 2% [Mn(C12H11NOS)(Cl2)(H2O)]· 3H2O. The optimized sensors exhibit Nernstian response for thiocyanate through a linear concentration ranging from (5 × 10−8 to 9.06 × 10−1 M) with a detection limit of 3 × 10−8 M and a slope of −57.7 mV decade−1, the measurement carried out in acetate buffer pH 4.7. The response time of electrode <10 s and the lifetime of the sensor more than 6 weeks. The proposed electrode was effectively utilized to estimation of thiocyanate in saliva sample, the results revealed a valid agreement with reference colorimetric method.

Highly Selective Potentiometric Sensing of Biologically Relevant Pyrophosphate and Lysophosphatidic Acid Using N-Alkyl/Aryl Ammonium Resorcinarenes/Extended-Resorcinarenes as Ionophores

The ionophore properties of four kinds of N-alkyl/aryl ammonium resorcinarenes and extended-resorcinarenes were inspected for the first time to fabricate polymeric membrane electrodes for determination of biologically relevant pyrophosphate (PPi) and lysophosphatidic acid (LPA). The proposed ion selective electrodes (ISEs) showed significant preference for PPi and LPA with significant selectivity pattern differences from the Hofmeister series. To gain further insight into the performances of the developed ISEs, the binding constants of ionophore-anion complexes in the plasticized membrane phase were investigated, along with the optimized geometries and calculated electrostatic potential. Nernstian potential responses with good reversibility to target anions can be observed when shifting the optimized membranes in aqueous solutions in the concentration range from 10^-6.5 to 10^-2.3/10^-2.2 M. Moreover, potentiometric sensings of PPi and LPA in mineral water and artificial serum were achieved in low μM concentration range, demonstrating their promising real-world applications. These results provide a promising avenue for the development of polymeric membrane electrodes for biological relevant anions and will broaden the scope of potentiometric sensing.

Anchoring H-Bond Donating/Accepting Pyrrolic Derivatives on Preorganized Scaffolds: Conformationally Switchable Bipedal/Tripodal and Locked Molecular Cage Ionophores for Potentiometric Sensing of Phosphate and Fluoride

The ionophore properties of a myriad of conformationally switchable bipedal/tripodal receptors and locked molecular cages were evaluated here for the first time to fabricate potentiometric sensors for the determination of environmentally important phosphate and fluoride. Owing to the competent ionophore properties such as high binding selectivity and affinity, the developed ion-selective electrodes displayed response preference for phosphate and fluoride with a selectivity pattern that differs distinctly from traditional Hofmeister series. Binding constants of the ionophore-anion complexes are determined to underscore how modifications in the preorganization and H-bond donating/accepting ability of a given series of ionophores can be exploited to improve the performance for potentiometric sensing. While conformationally switchable bipedal/tripodal ionophores prefer tetrahedral oxyanions, locked molecular cages shift their preference to spherical halides gradually. Nernstian potential responses with good reversibility to target anions can be observed when shifting the optimized membrane electrodes in aqueous solutions within the concentration range of 10^-6.5-10^-2.0 M. Moreover, potentiometric determination of phosphate and fluoride in mineral water, soil, and tap water samples was achieved in a low μM concentration range with high accuracy, confirming their promising utility in real world applications.

Embedding of Functionalized Coordination Cages and a Molecular Knot in a Polymeric Membrane for Potentiometric Sensing of Environmentally Important Oxyanions and Halides

Three kinds of coordination cages and a molecular knot with inductively activated ⁺P-H, N-H, or C-H hydrogen bond donors anchoring in the functionalized cavities were inspected as ionophores to develop polymeric membrane ISEs for potentiometric sensing of environmentally important oxyanions and halides. The proposed ISEs displayed significant preference for perrhenate, phosphate, or chloride with a selectivity pattern distinctively different from the sequence depending on the Gibbs free energy of hydration owing to the high degree of shape, charge, and size selectivity originating from the rigidity and complementarity of the binding cavities. To gain further insight into the response characters of the proposed ISEs, the binding constants of ionophore-anion complexes in the membrane phase were investigated, and the binding affinity, together with the Hofmeister series, correlates well with the determined selectivity pattern of the proposed ISEs. Optimizing the composition of the membrane such as lipophilic additives and plasticizers produced ISEs displaying Nernstian/near-Nernstian potentiometric responses to primary anions with a wide linear range, improved detection limits, good reversibility, and satisfying lifetime. Potentiometric determination of perrhenate, phosphate, and chloride in river water, mineral water, and artificial serum samples was achieved with good recovery and accuracy using the proposed ISEs, demonstrating their potential for real-life applications. These results will shed new light on how novel ionophores could be designed for potentiometric sensing and broaden the scope of host-guest chemistry of coordination cages and molecular knots.

Interpretation of the adsorption of metals on quartz crystal based-macromolecule via advanced modeling of equilibrium isotherms

In this article, new insights about the metals-porphyrin complexes are proved by analyzing the zinc, nickel and chromium adsorption process over the well-known porphyrin macromolecule. The use of the quartz crystal microbalance (QCM) apparatus allows the control of the complexation systems' experimental adsorption data operating at four temperatures. The experimental results and the physical models reveal that the zinc and nickel complexation processes are to be examined using the mono layer adsorption model. While, the double layer model describes the interaction between the chromium compound and the porphyrin. Actually, the three metals are shown to be adsorbed by a multi-docking process in the physicochemical description. The endothermic character of the investigated processes is shown through the appropriate data of the principal parameter adsorbent sites' density. Hence, several porphyrin sites are exclusively stimulated at high temperature. The parameters of van del Waals, depicting the influences of the lateral interactions, explain the nickel isotherms down trend. The chemical bonds are shown to be carried out between the zinc and the porphyrin through the calculated adsorption energies. Considering the thermodynamic study, and referring to the configurational entropy and the free enthalpy, it is to be noted that the disorder peak of the three mechanisms is reached when the equilibrium concentration is equal to the energetic parameters' values for each system. The nickel enthalpy revealed for high concentration that the adsorbates' lateral interactions disapproved the nickel chloride adsorption. The free enthalpy trends, that observed two stability states of the chromium compound, confirmed the chromium double layer mechanism.

Effect of solvent on the electronic absorption spectral properties of mixed β-octasubstituted free base tetraphenylporphyrins

A near planar macrocycle containing 2,3,12,13-tetraphenylethynyl-5,10,15,20-tetrakis-(4[Formula: see text]-[Formula: see text]-butylphenyl)porphyrin, H2T(4[Formula: see text]-[Formula: see text]-Bu Ph)P(PE)4 and a series of antipodally mixed substituted nonplanar porphyrins, 2,3,5,10,12,13,15,20-octaphenyl-7,8,17,18-tetra(2[Formula: see text]-thienyl/phenylethynyl, PE)porphyrin, H2OPP(2[Formula: see text]-Th/PE)4 and 2,3,12,13-tetramethyl-7,8,17,18-tetra(2[Formula: see text]-thienyl/PE)-5,10,15,20-tetraphenylporphyrin, H2TPP(CH[Formula: see text](2[Formula: see text]-Th/PE)4were examined by electronic absorption spectroscopy in twenty different solvents. The presence of push-pull substituents at the antipodal [Formula: see text]-pyrrole positions of the nonplanar macrocycle induces varying degrees of orthogonal dipole moments to the porphyrin ring. The influence of different solvents on the degree of nonplanarity and electronic nature of the macrocycle on their electronic absorption spectral properties were examined. Generally, free base porphyrins showed dramatic solvent dependent absorption spectral band shifts and follow the order: H2OPP(PE)4 > H2OPP(2[Formula: see text]-Th)[Formula: see text] H2TPP(CH[Formula: see text](2[Formula: see text]-Th)4 >[Formula: see text]H2TPP(CH[Formula: see text](PE)4 > H2T(4[Formula: see text]-[Formula: see text]Bu Ph)P(PE)4. Absorption spectral data in different solvents was analyzed using selected solvatochromic parameters, ([Formula: see text] – 1)/(2[Formula: see text] + 1), [Formula: see text] (30),[Formula: see text], and [Formula: see text]*. The enhanced red-shift of the absorption bands of the mixed substituted porphyrins in polar solvents was influenced by solvent-core (porphyrin) interaction and is reflected from the 1H NMR chemical shift of the core imino-hydrogens in polar solvents relative that observed in less polar solvents. The magnitude of the difference in chemical shift ([Formula: see text], ppm) of imino-hydrogens in DMSO-d6 relative to that in CDCl3 follow the order: H2TPP(CH[Formula: see text](2[Formula: see text]-Th)4 (1.37 ppm) > H2OPP(PE)4 (1.17 ppm) > H2TPP(CH[Formula: see text](PE)4 (0.57 ppm). The large red-shift in B and Q bands in polar solvents relative to apolar (or less polar) solvents has been possible due to the combined effect of the electronic nature of the macrocycle, its nonplanarity, and solvent-porphyrin core interactions.

Statistical Physics Modeling of Sorption Isotherms of Aluminum, Iron, and Indium on Tetraphenylporphyrin (H2TPP) and Tetrakis(4-tolylphenyl)porphyrin (H2TTPP): Phenomenological Investigation of Metalloporphyrins at the Molecular Level

A quartz crystal adsorbent functionalized with two promising porphyrins (the 5,10,15,20-tetrakis(4-tolylphenyl)porphyrin and the 5,10,15,20-tetraphenylporphyrin) was applied for the investigation of the adsorption phenomenon of aluminum chloride, iron chloride, and indium chloride. The aim is to prove new insights about the appropriate adsorption materials for metalloporphyrin fabrication. The equilibrium isotherms were measured at five adsorption temperatures (from 290 to 330 K) through the microbalance (QCM) method. The discussion of the experimental observations indicated that the adsorption of the aluminum chloride and the iron chloride was performed via a monolayer process. On contrary, the participation of the chloride ions in the double-layer adsorption of the indium chloride was explained by the layer-by-layer process. Overall, the statistical physics modeling of the experimental curves indicated that the number of ions per adsorbent site $n$ was found inferior to 1 for all the adsorption systems (multi-interaction process for the three ions). Interestingly, the physicochemical investigation of the three adopted models showed that the complexation mechanism of the tested porphyrins was an endothermic process since the two steric parameters ( $n$ and $P_M$ ) increased with the rise of the temperature. The FeCl3 curves were discussed via a monolayer adsorption model which includes the parameters $a$ and $b$ (lateral interaction description), indicating the lowest stability of the formed iron-porphyrin complex. The energetic study showed that the adsorption energies $\mid -\Delta E_{1/2}\mid$ of AlCl3 on H2TTPP and H2TPP are superior to 40 kJ/mol (chemical adsorption mechanism), whereas the adsorption mechanisms of FeCl3 and InCl3 took place via a physical process since they presented adsorption energy values lower than 40 kJ/mol.

Polymeric Membrane Fluoride-Selective Electrodes Using Lewis Acidic Organo-Antimony(V) Compounds as Ionophores

Four Lewis acidic organo-antimony(V) compounds with strong binding affinity to fluoride were used for the first time as ionophores to fabricate polymeric membrane fluoride-selective electrodes. Improved detection limits and significant anti-Hofmeister selectivity could be achieved by optimizing ionophores, lipophilic additives, and plasticizers. Membrane electrodes fabricated with tetrakis-(pentafluorophenyl)stibonium (ionophore 2) performed best in detection limit, sensitivity, and selectivity. Optimal performance was obtained by fluoride with a slope of -59.5 mV/decade in the linear range of 1 × 10^-5 to 4 × 10^-2 M and a detection limit of 5 × 10^-6 M. Studies on the influence of sample solution pH demonstrate that the best pH for fluoride determination is pH 3.0. All of the electrodes studied respond rapidly (in 1 min) in different concentrations of fluoride solutions. The anion-ionophore complex constants in the membrane phase determined using the segmented sandwich membrane method correlate well with the solution-phase binding data and determined selectivity sequence of the ion-selective electrodes. The possibility of real life application of the optimized electrodes was assessed by determination of fluoride concentrations in tap water.

Reusable colorimetric and fluorescent chemosensors based on 1,8-naphthalimide derivatives for fluoride ion detection

Two 1, 8-naphthalimide derivatives, 2-(2-ethylhexyl)-6-(2-(4-(5-phenyl-1,3,4-oxadiazol-2-yl)benzylidene)hydrazinyl)-1H-benzo[de]isoquinoline-1,3(2H)-dione (named as NAOZ) and 2-(2-ethylhexyl)-6-(2-(4-(5-phenyl-1,3,4-thiadiazol-2-yl)benzylidene)hydrazinyl)-1H-benzo[de]isoquinoline-1,3(2H)-dione (named as NATZ), containing hydrazone and thiadiazole/oxadiazole, were successfully synthesized. Compounds NAOZ and NATZ were further served as efficient reversible colorimetric and fluorescent chemosensors for fluoride ion over a wide range of other anions (Cl^-, Br^-, I^-, NO₃^-, ClO₄^-, HSO₄^-, BF₄^-, and PF₆^- as their (C₄H₉)₄N⁺ salts) because fluoride ion can deprotonate the hydrazone moiety, leading to the observed long-wavelength color change. Interestingly, CO₂ can recover the charge transfer (CT) absorption and photoluminescence intensities of compound NAOZ/NATZ + F^-, because CO₂ can react with a small amount of water to form acids, which can provide protons.

Fluorescence detection of fluorine ions in biological fluids based on aggregation-induced emission

Traditional chemical and biological sensors developed through aggregation-induced emission (AIE) are mainly based on “Turning on” pattern of fluorescence enhancement, which often has poor selectivity and can be easily interfered with by other substances. On this basis, an AIE-based tetraphenyl ethylene (TPE) derivative (TPE-COOH) was prepared in this study and aggregated by adding Al³⁺, so as to form the TPE-COOH/Al³⁺ polymer. TPE-COOH fluorescence was enhanced through AIE principle, thus realizing the “Turning on” state. F⁻ could bind to Al³⁺ after the addition of F⁻ ions which would result in the decomposition of TPE-COOH/Al³⁺ aggregate, dissolved state of TPE-COOH and gradual reduction of fluorescence intensity of the system, thus realizing “Turning off” state. Moreover, F⁻ ions in biological fluid were analyzed and detected through such AIE-based “Turning on-off” pattern. The linear range of this method for F⁻ detection was 3–12 μM and the detection limit was 0.9 μM.

Schematic diagram of fluorescence detection of F⁻ ions in biological fluids based on TPE-COOH/Al³⁺ polymer Aggregation-Induced Emission (AIE) “Turning on–off” mode.

Depolymerization-Induced Electrochemiluminescence of Insoluble Porphyrin in Aqueous Phase

Exploring efficient and robust electrochemiluminescence (ECL) performance of liposoluble porphyrins in aqueous phase for analytical purposes especially for important biological targets is still very challenging. In this work, a novel depolymerization-induced electrochemiluminescence (DIECL) of porphyrin and β-cyclodextrin (β-CD) self-assembly through a coreactant route was discovered. Among the studied meso-tetrasubstituted porphyrins, self-assembly of 5,10,15,20-tetrakis(4-hydroxyphenyl) porphyrin (THPP) and β-CD (THPP@β-CD) exhibits the best DIECL behavior with high efficiency (21.8%) as well as good reproducibility and stability. A mechanistic study suggests that the facile complexation of porphyrins with amphiphilic β-CD via hydrogen bonding interaction greatly improves the water insolubility and the aggregation-caused deficient ECL of liposoluble porphyrins in aqueous solution. Furthermore, because of the strong hydrogen bonding between the hydroxyl groups on THPP@β-CD and a highly electronegative substrate, such THPP@β-CD is found to serve as an efficient luminophore for recognition of most electronegative fluoride (F^-) in the aqueous phase with high sensitivity and selectivity, together with a low limit of detection (0.74 μΜ). The simplicity of this THPP@β-CD and its unique DIECL property in current work provides a new guide for the ECL applications of liposoluble porphyrins in aqueous phase.

Naked-Eye Heterogeneous Sensing of Fluoride Ions by Co-Polymeric Nanosponge Systems Comprising Aromatic-Imide-Functionalized Nanocellulose and Branched Polyethyleneimine

Heterogeneous colorimetric sensors for fluoride ions were obtained by cross-linking TEMPO-oxidized cellulose nanofibers (TOCNF) with chemically modified branched polyethyleneimine 25 kDa (bPEI). Functionalization of bPEI primary amino groups with aromatic anhydrides led to the formation of the corresponding mono- and bis-imides on the grafted polymers (f-bPEI). A microwave-assisted procedure allowed the optimization of the synthetic protocol by reducing reaction time from 17 h to 30 minutes. Hydrogels obtained by mixing different ratios of TOCNF, bPEI and f-bPEI were lyophilized and thermally treated at about 100 °C to promote the formation of amide bonds between the amino groups of poly-cationic polymers and the carboxylic groups of cellulose nanofibers. This approach generated a series of cellulose nanosponges S1-S3 which were characterized by FT-IR and by solid state ¹³ C CPMAS NMR. These sponge materials can act as colorimetric sensors for the selective naked-eye recognition of fluoride ions over chloride, phosphate and acetate ions at concentrations of up to 0.05 M in DMSO. Moreover, when the sponges were functionalized with perylene tetracarboxylic diimide, successful naked-eye detection was achieved with only 0.02 % w/w of chromophore units per gram of material.

Miniaturization overcomes macro sample analysis limitations: Salicylate-selective polystyrene nanoparticle-modified optical sensor

Salicylate-selective polystyrene micro-optode is engineered using a mixed solvent method. The size of the particles (200-400 nm) and the distribution of the recognition components onto their surface were elucidated by transmission electron microscope and confocal fluorescence microscope. The polystyrene micro/nanoparticles are modified with thiourea derivative as ionophore, ETH 7075 as chromoionophore, and tridodecylmethyl ammonium chloride (TDMAC) as ion-exchanger. The response mechanism depends on the selective binding of the ionophore at the surface of the particles to salicylate. A concomitant protonation of the chromoionophore results in a decrease in the absorbance at the maximum wavelength, 535 nm. Enabling this sensing interaction at the micro-scale decreases the response time of the optode to be lower than 10 s the concentration range of 3-70 µM, with a detection limit of 2.1 μM. This microsphere sensing platform demonstrated excellent performance in the determination of salicylate in spiked urine samples and in pharmaceutical formulations. Further miniaturization of these micro-optodes promises in-vivo analysis of intracellular analytes.

Revisiting the fluoride binding behaviour of dipyrrolylquinoxaline in aqueous medium: a copper ion mediated approach

An ion detection methodology employing synergistic interaction between copper(ii) ions and fluoride with 2,3-dipyrrol-2′-yl-quinoxaline (SR1) is investigated with a particular target to detect fluoride in an aqueous environment.

A newly developed highly selective Zn2+-AcO- ion-pair sensor through partner preference: equal efficiency under solitary and colonial situation

Unusual self-sorting of an ion-pair under highly crowded conditions driven by a synthesized intelligent molecule 2-((E)-(3-((E)-2-hydroxy-3-methoxybenzylideneamino)-2-hydroxypropyl imino)methyl)-6-methoxyphenol, hereafter HBP, is described. When a mixture of various metal salts was allowed to react with HBP, only a specific ion-pair Zn^II/AcO^- in the solution simultaneously reacted, resulting in high-fidelity ion-pair recognition of HBP. This phenomenon was evidenced by significant changes in the absorption spectra and huge enhancement in emission intensity of HBP. The property that one molecule preferring one particular cation-anion pair over others is a rare but interesting phenomenon. Thus, the potential to interact selectively with the targeted ion-pair resulting in the formation of a specific complex recognized HBP as a new class of molecule that might find future applications in real time and on-site monitoring and separation of new molecules.

A Cu(ii) mediated approach for colorimetric detection of aqueous fluoride in ppm level with a Schiff base receptor

Inspired by the importance of fluoride detection in aqueous environment, a new methodology is demonstrated by employing the synergistic reaction of fluoride and Cu(ii) salts with a designed Schiff base receptor.

Mopping up the Oil, Metal, and Fluoride Ions from Water

The recycle, cleaning, and reuse of water are highly important for environmental remediation. This issue is addressed by creating a fluorescent zwitterionic spirocyclic Meisenheimer complex with high chelating propensity for toxic metals using low-cost starting materials and a one-pot synthesis technique. The resulting material is able to detect fluoride up to 12.8 ppb level and remove 82% aqueous fluoride from 1000 mL of 100 ppm fluoride solution in a single contact. The material demonstrates rapid kinetics and is capable of dropping the toxic metal ion (Pb/Hg/Cd) concentration below 0.2 ppb within 10 min. A resin-free, precipitation-free, and reusable technique has been developed for the removal of toxic metal ions and fluoride from extremely polluted water. Moreover, utilizing its extreme hydrophobicity, polystyrene sponges have been coated with the Meisenheimer complex to mop up oil spill and organic solvents from a biphasic mixture.

An Ionophore-Based Anion-Selective Optode Printed on Cellulose Paper

A general anion-sensing platform is reported based on a portable and cost-effective ion-selective optode and a smartphone detector equipped with a color analysis app. In contrast to traditional anion-selective optodes using a hydrophobic polymer and/or plasticizer to dissolve hydrophobic sensing elements, the new optode relies on hydrophilic cellulose paper. The anion ionophore and a lipophilic pH indicator are inkjet-printed and adsorbed on paper and form a "dry" hydrophobic sensing layer. Porous cellulose sheets also allow the sensing site to be modified with dried buffer that prevents any sample pH dependence of the observed color change. A highly selective fluoride optode using an Al^III -porphyrin ionophore is examined as an initial example of this new anion sensing platform for measurements of fluoride levels in drinking water samples. Apart from Lewis acid-base recognition, hydrogen bonding recognition is also compatible with this sensing platform.

Multi-ion detection and molecular switching behaviour of reversible dual fluorescent sensor

The selective chemosensing behaviour of imidazole bisthiocarbohydrazone (IBTC) towards F^- and Cu²⁺ are studied via colorimetric, UV-Visible, fluorescence spectra studies, and binding constants were calculated. The ¹H NMR titration study strongly support that the deprotonation of IBTC followed by the hydrogen bond formation via N1H1 and N2H2 protons with fluoride ion. The fluorescence inactive IBTC-Cu complex became fluorescence active in the presence of perchlorate (ClO₄^-) ion. The selective detection of perchlorate ion was also explained. The F^- sensing mechanism of IBTC has been investigated by Density Functional Theory (DFT) and Time-Dependent Density Functional Theory (TDDFT) methods. The theoretical outcomes well reproduce the experimental results. And it concluded the NH protons, nearby the imine group was first captured by the added F^- ion and then deprotonation happened followed by the formation of hydrogen bond. The IBTC found good reversibility character with the alternative addition of Ca²⁺ and F^-. The multi-ion detection of IBTC was used to construct the NOR, OR and INHIBITION molecular logic gates.

Highly selective and sensitive sensing for Al3+ and F− based on green photoluminescent carbon dots

A novel sensor for metal ions by mean of CDs with a PL enhancement response, which shows high sensitivity and selectivity. Furthermore, the CDs-Al³⁺ ions system could be employed to probe F⁻ anions based on a PL “on–off” model.

Label-free polymerization amplified potentiometric sensing platform for radical reactions using polyion sensitive membrane electrodes as transducers

Based on the cascade amplification abilities of radical polymerization reactions, an amplified potentiometric sensing platform for radical reactions was developed.

Visual detection of Al(3+) ions using conjugated copolymer-ATP supramolecular complex

A colorimetric Al(3+) sensor based on fluorescence recovery of a conjugated copolymer-ATP complex is proposed. An optimized ratio of two polythiophene (PT) monomers is utilized to synthesize copolymer (CP) that yielded maximized colorimetric response for Al(3+) in deionized (DI) and tap water. The electrostatic disassembly of CP-ATP upon addition of Al(3+) led to an evident visual color change. The lowest concentration of Al(3+) for naked eye observation is around 4 μM, which is below the threshold levels in drinking water according to European Economic Community (EEC) standard. Besides, the proposed assay showed a similar response to Al(3+) in tap water. The proposed methodology showed selective and sensitive detection for Al(3+) in analytically relevant concentration ranges without involving sophisticated instrumentation, illustrating the applicability for on-site drinking water monitoring.

The Detection of Helicobacter hepaticus Using Whispering-Gallery Mode Microcavity Optical Sensors

Current bacterial detection techniques are relatively slow, require bulky instrumentation, and usually require some form of specialized training. The gold standard for bacterial detection is culture testing, which can take several days to receive a viable result. Therefore, simpler detection techniques that are both fast and sensitive could greatly improve bacterial detection and identification. Here, we present a new method for the detection of the bacteria Helicobacter hepaticus using whispering-gallery mode (WGM) optical microcavity-based sensors. Due to minimal reflection losses and low material adsorption, WGM-based sensors have ultra-high quality factors, resulting in high-sensitivity sensor devices. In this study, we have shown that bacteria can be non-specifically detected using WGM optical microcavity-based sensors. The minimum detection for the device was 1 × 10⁴ cells/mL, and the minimum time of detection was found to be 750 s. Given that a cell density as low as 1 × 10³ cells/mL for Helicobacter hepaticus can cause infection, the limit of detection shown here would be useful for most levels where Helicobacter hepaticus is biologically relevant. This study suggests a new approach for H. hepaticus detection using label-free optical sensors that is faster than, and potentially as sensitive as, standard techniques.

Dip in colorimetric fluoride sensing by a chemically engineered polymeric cellulose/bPEI conjugate in the solid state

A novel heterogeneous, selective dip-in sensor for fluoride has been developed by cross-linking oxidized cellulose with branched PEI functionalized with pNO₂-phenyl urea units.

Auto-reusable receptors for selective colorimetric recognition of fluoride

Two auto-reusable colorimetric receptors for selective recognition of fluoride in polar medium are reported.