Efficient Metal-Free Electrocatalysts for Oxygen Reduction: Polyaniline-Derived N- and O-Doped Mesoporous Carbons

Probing Electrocatalytic Synergy in Graphene/MoS2/Nickel Networks for Water Splitting through a Combined Experimental and Theoretical Lens

The development of low-cost and active electrocatalysts signifies an important effort toward accelerating economical water electrolysis and overcoming the sluggish hydrogen or oxygen evolution reaction (HER or OER) kinetics. Herein, we report a scalable and rapid synthesis of inexpensive Ni and MoS2 electrocatalysts on N-doped graphene/carbon cloth substrate to address these challenges. Mesoporous N-doped graphene is synthesized by using electrochemical polymerization of polyaniline (PANI), followed by a rapid one-step photothermal pyrolysis process. The N-doped graphene/carbon cloth substrate improves the interconnection between the electrocatalyst and substrate. Consequently, Ni species deposited on an N-doped graphene OER electrocatalyst shows a low Tafel slope value of 35 mV/decade at an overpotential of 130 mV at 10 mA/cm2 current density in 1 M KOH electrolytes. In addition, Ni-doped MoS2 on N-doped graphene HER electrocatalyst shows Tafel slopes of 37 and 42 mV/decade and overpotentials of 159 and 175 mV, respectively, in acidic and alkaline electrolytes at 10 mA/cm2 current density. Both these values are lower than recently reported nonplatinum-group-metal-based OER and HER electrocatalysts. These excellent electrochemical performances are due to the high electrochemical surface area, a porous structure that improves the charge transfer between electrode and electrolytes, and the synergistic effect between the substrate and electrocatalyst. Raman spectroscopy, X-ray photoelectron spectroscopy, and density functional theory (DFT) calculations demonstrate that the Ni hydroxide species and Ni-doped MoS2 edge sites serve as active sites for OER and HER, respectively. Finally, we also evaluate the performance of the HER electrocatalyst in commercial alkaline electrolyzers.

A Fabric-Based Strain Sensor with a Microbridge Structure and the Supercapacitor-Powered Integrated Sensing System

Developing fabric-based strain sensors with high sensitivity and stability is in high demand for wearable electronics. Herein, carbon nanotubes (CNTs) and polypyrrole (PPy) are coated on a thermoplastic polyurethane (TPU) fabric as strain sensors. A microbridge structure, in which CNT bridges the stretching-induced cracks, has been designed for the TPU-CNT-PPy strain sensor. The microbridge structure can significantly enhance the electrical resilience, ensuring the improved sensitivity and stability of strain sensors. As a result, our TPU-CNT-PPy strain sensors deliver high sensitivity (GF = 231.5) with a broad working range (150%) and fast response and recovery time (166/195 ms). In addition, our TPU-CNT-PPy could also be used as flexible electrodes of the microsupercapacitors (MSCs) as a power supplier for the integrated sensing system. The TPU-CNT-PPy-based MSCs exhibit a high specific capacitance (460.3 mF cm-2 at 0.5 mA cm-2) and excellent cycling stability (96.69% capacitance retention for 10,000 charge/discharge cycles). Finally, we demonstrated an integrated sensing system using TPU-CNT-PPy as both MSCs and strain sensors, where the current signals of the sensors could be well detected via Bluetooth. This study offers a microbridge strategy to fabricate strain sensors with high sensitivity and stability and develops an integrated sensing system for the actual applications of wearable electronics.

Metal-Free Nitrogen-Doped Mesoporous Carbons for the Mild and Selective Synthesis of Pyrroles from Nitroarenes via Cascade Reaction

The cascade synthesis of pyrroles from nitroarenes is an attractive alternative strategy. However, metal catalysts and relatively high temperatures cover the existing reported catalytic systems for this strategy. The development of nonmetallic heterogeneous catalytic systems for the one-pot synthesis of pyrrole from nitroarenes under mild conditions is both worthwhile and challenging. Herein, we describe an exceptionally efficient method for the synthesis of N-substituted pyrroles by the reductive coupling of nitroarenes and diketones over heterogeneous metal-free catalysts under mild conditions. Nonmetallic NC-X catalysts with high activity were prepared from the pyrolysis of well-defined ligands via simple sacrificing hard template methods. Hydrazine hydrate, formic acid, and molecular hydrogen can all be used as reducing agents in the hydrogenation/Paal-Knorr reaction sequence to efficiently synthesize various N-substituted pyrroles, including drugs and bioactive molecules. The catalytic system was featured with good tolerance to sensitive functional groups and no side reactions such as dehalogenation and aromatics hydrogenation. Hammett correlation studies have shown that the electron-donating substituents are beneficial for the one-pot synthesis of N-substituted pyrroles. The results established that the outstanding performance of the catalyst is mainly attributed to the contribution of graphitic N in the catalyst as well as the promotion effect of the mesoporous structure on the reaction.

Silica-Derived Nanostructured Electrode Materials for ORR, OER, HER, CO2RR Electrocatalysis, and Energy Storage Applications: A Review

Silica-derived nanostructured catalysts (SDNCs) are a class of materials synthesized using nanocasting and templating techniques, which involve the sacrificial removal of a silica template to generate highly porous nanostructured materials. The surface of these nanostructures is functionalized with a variety of electrocatalytically active metal and non-metal atoms. SDNCs have attracted considerable attention due to their unique physicochemical properties, tunable electronic configuration, and microstructure. These properties make them highly efficient catalysts and promising electrode materials for next generation electrocatalysis, energy conversion, and energy storage technologies. The continued development of SDNCs is likely to lead to new and improved electrocatalysts and electrode materials. This review article provides a comprehensive overview of the recent advances in the development of SDNCs for electrocatalysis and energy storage applications. It analyzes 337,061 research articles published in the Web of Science (WoS) database up to December 2022 using the keywords "silica", "electrocatalysts", "ORR", "OER", "HER", "HOR", "CO2RR", "batteries", and "supercapacitors". The review discusses the application of SDNCs for oxygen reduction reaction (ORR), oxygen evolution reaction (OER), hydrogen evolution reaction (HER), carbon dioxide reduction reaction (CO2RR), supercapacitors, lithium-ion batteries, and thermal energy storage applications. It concludes by discussing the advantages and limitations of SDNCs for energy applications.

Nitrogen sites prevail over textural properties in N-doped carbons for the oxygen reduction reaction

Nitrogen-doped carbon-based electrodes are among the most promising alternatives to platinum-based electrodes in the cathode of fuel cells and metal-air batteries, where the oxygen reduction reaction (ORR) takes place. Among the approaches for improving ORR activity, nitrogen functionalities and well-developed textural properties have proved very effective. Nonetheless, the question of which between nitrogen active sites or textural properties are more crucial in N-doped carbon materials remains unanswered. This work proposes a comparative and critical approach through the selective functionalization of four commercial activated carbons with different textural properties. This study highlights the greater importance of N-doping in relation to the textural properties of carbon materials, and provides fundamental insights for conclusively addressing the ongoing debate within the carbon community about the significance of these two factors in the context of ORR.

Probiotic potential and immunomodulatory properties in Enterococcus faecium GMB24 and Enterococcus hirae SMB16 isolated from goat and sheep milk

Probiotic attributes of lactic acid bacteria isolated from goat and sheep milk samples were analysed by culturing them on an MRS agar medium. The most potential isolates, GMB24 and SMB16, were identified by biochemical tests which had ability to tolerate different concentrations of acid and bile and phenol resistance. They were further identified as Enterococcus faecium GMB24 and Enterococcus hirae SMB16 by 16S rRNA gene sequencing approach. The probiotic potential of the isolates GMB24 and SMB16 were recorded including antimicrobial activity against pathogenic bacteria viz., Escherichia coli (MTCC118), Staphylococcus aureus (MTCC7443), Pseudomonas aeruginosa (MTCC424), Listeria monocytogens (MTCC657) and Salmonella typhimurium (MTCC733), and antibiotic susceptibility test. The isolates SMB16 and GMB24 exhibited a higher zone of inhibition against P. aeruginosa (19.00 ± 0.57 mm) and S. aureus (25.66 ± 0.88 mm), respectively. The data from these experiments were used for the principal component analysis (PCA) to assess the survivability of the isolates under different factors. The heatmap generated in this study clustered the bacterial isolates based on their phenotype properties. Further, immunomodulating activities of these probiotic bacteria were tested on neutrophil adhesion test, haemagglutinating antibody titer and delayed-type hypersensitivity. Probiotic E. faecium GMB24 and E. hirae SMB16, at 10⁹ cells/mL doses per day, increased the neutrophil adhesion, haemagglutinating antibody titer and DTH in comparison to the untreated control group. The isolates showed negative test for haemolytic and gelatinase activities and hence were considered safe. E. faecium GMB24 and E. hirae SMB16 were shown to have high probiotic potential and immune-stimulant action.

Exploring the structural dependence of metal-free carbon electrocatalysts on zinc-based metal-organic framework types

Metal-organic frameworks (MOFs) have been widely used as precursors to derive carbon-based electrocatalysts for the oxygen reduction reaction (ORR) due to their high porosity and tunable chemical composition/structure. However, the influence of MOF type on the structure and further ORR activity of derived metal-free carbon catalysts is still elusive. In the present work, a series of different Zn-based MOFs were employed as precursors to explore this issue. Meanwhile, prepare N-doped metal-free carbon catalysts were prepared for the ORR under the activation of sacrificial urea (which is effective to enhance the ORR activity of carbon-based catalysts). By analyzing the intermediates during pyrolysis, it is found that the decisive role of MOF types on the doped N and the morphology of derived carbon catalysts was played by the Zn coordination environment of MOFs and its reactivity with the decomposition intermediate of urea. Although the structure and porosity of derived carbon catalysts from different MOFs are very different, they all showed superior ORR activity and Zn-air battery performance up to 20 wt% Pt/C benchmark catalysts. From the above analyses, the combination of urea and compounded Zn is also a promising activation method for the preparation of highly-efficient metal-free carbon electrocatalysts.

Hierarchically Ordered Nanoporous Carbon with Exclusively Surface-Anchored Cobalt as Efficient Electrocatalyst

A hierarchically ordered porous carbon electrocatalyst with exclusively surface-anchored cobalt species, dubbed Co@HOPC, is synthesized from polyaniline and cobalt-functionalized silica microparticles templates, and its high electrocatalytic activity for the oxygen evolution reaction (OER) is demonstrated. The material requires a small potential (320 mV) to drive the reaction with a current density of 10 mA cm^-2 and a small Tafel slope of 31.2 mV dec^-1 . Moreover, Co@HOPC shows better catalytic activity for OER than in situ cobalt-doped and surface cobalt-loaded hierarchically ordered porous carbon materials synthesized by traditional methods. This is due to the abundant surface cobalt species present in Co@HOPC and the material's good electrical conductivity. This work provides a new strategy to utilize functionalized silica microparticles as templates to synthesize hierarchically ordered porous carbon materials with metal-rich surfaces and efficient electrocatalytic activities.

Activation of H2O Tailored by Interfacial Electronic States at a Nanoscale Interface for Enhanced Electrocatalytic Hydrogen Evolution

Despite the fundamental and practical significance of the hydrogen evolution reaction (HER), the reaction kinetics at the molecular level are not well-understood, especially in basic media. Here, with ZIF-67-derived Co-based carbon frameworks (Co/NCs) as model catalysts, we systematically investigated the effects of different reaction parameters on the HER kinetics and discovered that the HER activity was directly dependent not on the type of nitrogen in the carbon framework but on the relative content of surface hydroxyl and water (OH^-/H₂O) adsorbed on Co active sites embedded in carbon frameworks. When the ratio of the OH^-/H₂O was close to 1:1, the Co/NC nanocatalyst showed the best reaction performance under the condition of high-pH electrolytes, e.g., an overpotential of only 232 mV at a current density of 10 mA cm^-2 in the 1 M KOH electrolyte. We unambiguously identified that the structural water molecules (SWs) in the form of hydrous hydroxyl complexes absorbed on metal centers {OH_ad·H₂O@M⁺} were catalytic active sites for the enhanced HER, where M⁺ could be transition or alkaline metal cations. Different from the traditional hydrogen bonding of water, the hydroxyl (hydroxide) groups and water molecules in the SWs were mainly bonded together via the spatial interaction between the p orbitals of O atoms, exhibiting features of a delocalized π-bond with a metastable state. These newly formed surface bonds or transitory states could be new weak interactions that synergistically promote both interfacial electron transfer and the activation of water (dissociation of O-H bonds) at the electrode surface, i.e., the formation of activated H adducts (H*). The capture of new surface states not only explains pH-, cation-, and transition-metal-dependent hydrogen evolution kinetics but also provides completely new insights into the understanding of other electrocatalytic reductions involving other small molecules, including CO₂, CO, and N₂.

Microstructure Evolution and Its Correlation with Performance in Nitrogen-Containing Porous Carbon Prepared by Polypyrrole Carbonization: Insights from Hybrid Calculations

The preparation of nitrogen-containing porous carbon (NCPC) materials by controlled carbonization is an exciting topic due to their high surface area and good conductivity for use in the fields of electrochemical energy storage and conversion. However, the poor controllability of amorphous porous carbon prepared by carbonization has always been a tough problem due to the unclear carbonation mechanism, which thus makes it hard to reveal the microstructure–performance relationship. To address this, here, we comprehensively employed reactive molecular dynamics (ReaxFF-MD) simulations and first-principles calculations, together with machine learning technologies, to clarify the carbonation process of polypyrrole, including the deprotonation and formation of pore structures with temperature, as well as the relationship between microstructure, conductance, and pore size. This work constructed ring expressions for PPy thermal conversion at the atomic level. It revealed the structural factors that determine the conductivity and pore size of carbonized products. More significantly, physically interpretable machine learning models were determined to quantitatively express structure factors and performance structure–activity relationships. Our study also confirmed that deprotonation preferentially occurred by desorbing the dihydrogen atom on nitrogen atoms during the carbonization of PPy. This theoretical work clearly reproduces the microstructure evolution of polypyrrole on an atomic scale that is hard to do via experimentation, thus paving a new way to the design and development of nitrogen-containing porous carbon materials with controllable morphology and performance.

Synergetic Effects of Mixed-Metal Polyoxometalates@Carbon-Based Composites as Electrocatalysts for the Oxygen Reduction and the Oxygen Evolution Reactions

The smart choice of polyoxometalates (POMs) and the design of POM@carbon-based composites are promising tools for producing active electrocatalysts for both the oxygen reduction (ORR) and the oxygen evolution reactions (OER). Hence, herein, we report the preparation, characterization and application of three composites based on doped, multi-walled carbon nanotubes (MWCNT_N6) and three different POMs (Na12[(FeOH2)2Fe2(As2W15O56)2]·54H2O, Na12[(NiOH2)2Ni2(As2W15O56)2]·54H2O and Na14[(FeOH2)2Ni2(As2W15O56)2]·55H2O) as ORR and OER electrocatalysts in alkaline medium (pH = 13). Overall, the three POM@MWCNT_N6 composites showed good ORR performance with onset potentials between 0.80 and 0.81 V vs. RHE and diffusion-limiting current densities ranging from −3.19 to −3.66 mA cm−2. Fe4@MWCNT_N6 and Fe2Ni2@MWCNT_N6 also showed good stability after 12 h (84% and 80% of initial current). The number of electrons transferred per O2 molecule was close to three, suggesting a mixed regime. Moreover, the Fe2Ni2@MWCNT_N6 presented remarkable OER performance with an overpotential of 0.36 V vs. RHE (for j = 10 mA cm−2), a jmax close to 135 mA cm−2 and fast kinetics with a Tafel slope of 45 mV dec−1. More importantly, this electrocatalyst outperformed not only most POM@carbon-based composites reported so far but also the state-of-the-art RuO2 electrocatalyst. Thus, this work represents a step forward towards bifunctional electrocatalysts using less expensive materials.

NiCo Alloy Nanoparticles on a N/C Dual-Doped Matrix as a Cathode Catalyst for Improved Microbial Fuel Cell Performance

The cathode material properties of the microbial fuel cell (MFC) have a quite important effect on their power generation capacity. Excellent oxygen reduction reaction (ORR) performance is the key to obtaining the remarkable capability of MFC. In this study, a series of catalysts are successfully prepared by a simple step-by-step hydrothermal, in situ growth, solution polymerization, and pyrolysis procedure. Here, the NiCo nanoparticles loading on nitrogen/carbon dual-doped matrix annealing at 800 °C (NiCo@DNC-800) under Ar shows good ORR activity with a maximum power density of 2325.60 ± 41.96 mW m^-2 in the case of the 2 mg cm^-2 minimal catalyst loading, and which is about 2.16 times more than that achieved by 20% Pt/C (1074.21 ± 39.36 mW m^-2 ). The unique N/C duel-doped matrix provides more graphitic-N and pyridinic-N that can reduce the resistance of electron diffusion and transport, together with the synergistic catalysis of NiCo active sites improving the oxygen reduction reaction performance of MFC greatly. In addition, the NiCo@DNC-800 cathode catalyst demonstrates that composite materials have great application potential in water pollution treatment and new green energy strategies.

N, O-codoped hierarchical porous graphitic carbon for electrochemical immunosensing of Lactobacillus rhamnosus GG

An ultrasensitive label-free electrochemical immunosensor was fabricated for quantitative detection of Lactobacillus rhamnosus GG (LGG). The N/O co-doped three-dimensional hierarchical porous graphitic (THPG) carbon was synthesized by a one-step synthesis of polyaniline hydrogel, and followed by simple carbonization and chemical activation procedures. Because of the unique structure design, the obtained THPG carbon networks possess an ultra-large specific surface area of 4859 m² g^-1 along with a class of highly graphitic carbons. The results offer an enormous surface area and excellent electrical conductivity for label-free electrochemical immunosensing of probiotic L. rhamnosus strain. Under optimal conditions, the immunosensor showed a good linear relationship between peak current and concentration of LGG (R² = 0.9976), with a detection limit of 2 CFU mL^-1. Furthermore, this label-free immunosensor also shows good specificity, long-term stability, and reliability, and could be applied to detect probiotic LGG in dairy products and drinks with satisfactory results. The present protocol was shown to be quite promising for practical screening and functional evaluation of probiotic products containing LGG. A ultrasensitive label-free electrochemical immunosensor based on THPG carbon was fabricated for detection of Lactobacillus rhamnosus GG.

N- and O-doped hollow carbons constructed by self- and extrinsic activation for the oxygen reduction reaction and flexible zinc-air Batteries

Zinc-air batteries (ZAB), especially those assembled on flexible substrates, have attracted great research attention in electronics and wearable electronics. However, the air-cathode reaction-oxygen reduction reaction (ORR) has limited the development of ZAB technology. In this study, a hollow carbon catalyst, NOC-1000-1, was prepared by pyrolysis of a mixture of a N-enriched Zn/bispyrozolate-based metal-organic framework and urea to replace the labile Pt-based catalysts for ORR. The employment of sacrifical urea eliminated the requirement for complicated post-treatment compared to the template method. Combined with self-activation (Zn evaporation), the obtained carbon showed a micro- and mesopore-dominant hierarchical structure coexisting with some macropores. Moreover, the doped N and O species were also tailored in a preferable configuration for ORR by simply screening the pyrolysis conditions. Under the synergistic effect of the preferable N and O configurations and pore structure, the derived carbon catalyst displayed superior ORR activity of 0.977 V onset potential and 0.867 V half-wave potential; these values are slightly better than those of the 20% Pt/C benchmark catalyst (0.985 and 0.861 V, respectively). Flexible solid-state ZABs were further assembled by employing the derived carbon catalyst as an air-cathode, and they exhibited a higher peak power density of 100.92 mW cm^-2 than a 20% Pt/C-RuO₂ battery as well as previously reported similar batteries and very high stability for up to 30 h. The flexible solid-state ZABs could drive a red light-emitting diode and run a 130-type motor for hours, which indicates their promising applications in real-world technologies.

High-performance electrocatalyst based on polyazine derived mesoporous nitrogen-doped carbon for oxygen reduction reaction

Nitrogen-doped porous carbon materials have high potential in metal-free electrocatalysts, which is essential for several renewable energy conversion systems. Herein, we report a convenient and environment-friendly method to fabricate a nitrogen doped mesoporous carbon (NMC) using a nonionic surfactant of Pluronic F127 micelles as the template and a Schiff-base polymer (polyazine) as the precursor. The synthesized NMCs were of spheric morphology and mesoporous structures with surface area up to 1174 m² g⁻¹ and high level of nitrogen (2.9–19 at%) and oxygen (4.9–7.4 at%) simultaneously doped. The electrochemical data of NMCs were analyzed in the context of the BET and XPS information. A correlation between ORR activity and the pyridinic-N was found. The NMC-700 demonstrate the highest electrocatalytic activity for ORR among the studied materials, which can be ascribed to the reasonable surface area and mesoporous structure, as well as the most abundant touchable pyridinic-N, thus providing more effective active sites for the oxygen reduction. In comparsion to the control sample, the NMC-700 provides the ORR electrocatalytic activity approximate to that of commercial Pt/C catalyst with a highly long-term stability.

Nitrogen-doped porous carbon materials have high potential in metal-free electrocatalysts, which is essential for several renewable energy conversion systems.

Plasma-Assisted Synthesis of Defect-Rich O and N Codoped Carbon Nanofibers Loaded with Manganese Oxides as an Efficient Oxygen Reduction Electrocatalyst for Aluminum-Air Batteries

The oxygen reduction reaction (ORR) with sluggish kinetics on the cathode of aluminum-air (Al-air) batteries greatly limits their further development. Here, a new strategy is proposed to synthesize oxygen and nitrogen codoped carbon nanofibers loaded with manganese oxides (MnO/Mn₂O₃/ONCNF-n) as an efficient electrocatalyst for ORR by using oxygen plasma surface etching. The MnO/Mn₂O₃/ONCNF-3 exhibit superior ORR performance in an alkaline electrolyte, which is attributed to various active sites including N and O heteroatoms, vacancies, and manganese oxides. Additionally, the fabricated homemade Al-air battery (AAB) with MnO/Mn₂O₃/ONCNF-3 exhibits a maximum power density of 129.7 mW cm^-2, demonstrating comparable performance to AABs based on the commercial Pt/C catalyst. This work provides a new approach of using O₂ plasma for enhancing the ORR catalytic activities of carbon materials.

Nanoarchitectured Porous Conducting Polymers: From Controlled Synthesis to Advanced Applications

Conductive polymers (CPs) integrate the inherent characteristics of conventional polymers and the unique electrical properties of metals. They have aroused tremendous interest over the last decade owing to their high conductivity, robust and flexible properties, facile fabrication, and cost-effectiveness. Compared to bulk CPs, porous CPs with well-defined nano- or microstructures possess open porous architectures, high specific surface areas, more exposed reactive sites, and remarkably enhanced activities. These attractive features have led to their applications in sensors, energy storage and conversion devices, biomedical devices, and so on. In this review article, the different strategies for synthesizing porous CPs, including template-free and template-based methods, are summarized, and the importance of tuning the morphology and pore structure of porous CPs to optimize their functional performance is highlighted. Moreover, their representative applications (energy storage devices, sensors, biomedical devices, etc.) are also discussed. The review is concluded by discussing the current challenges and future development trend in this field.

Para-substituted sulfonic acid-doped protonated emeraldine salt nanobuds: a potent neural interface targeting PC12 cell interactions and promotes neuronal cell differentiation

Structural parameters, such as metal-like semiconductor and electrochemical properties of functionalized polyaniline, hold great potential especially for the development of the cell-substrate interface due to its ion/electron transfer ability. We report the one-step synthesis of sulfonic acid-doped polyaniline nanobuds (s-PANINbs) with controlled shape/size under various oxidation potentials. The different oxidation states of s-PANINbs are used to investigate the cell-specific platform for the induction of neuronal networks in PC12 cells, including the growth, proliferation, and differentiation of cells. The unique structure of one-dimensional (1-D) s-PANINbs enhances its intrinsic conductive properties, and facilitates the dispersibility and electrochemical activity via covalent bonding with dopants. The protonated emeraldine salt nanobuds of s-PANINbs synthesized at 0.18 V anodic potential demonstrated low resistivity (∼81.18 mΩ) and charge transfer resistance (∼3253 Ω). The most biologically compatible protonated emeraldine salt was used in vitro to induce PC12 cells associated with neurite outgrowth, contributing to the electrophysiology of neuronal cells under an external electrical stimulation. The western blotting analysis and qRT-PCR results show that β-III Tubulin, synapsin I, and TREK-1 are highly expressed in PC12 cells, confirming their successful differentiation into neural-specific cells. Our approach demonstrates the promising role of the self-standing framework based on the s-PANINbs of the protonated emeraldine salt in peripheral nerve repair for the future in vivo cell-interface.

Design Strategies of Non-Noble Metal-Based Electrocatalysts for Two-Electron Oxygen Reduction to Hydrogen Peroxide

Hydrogen peroxide (H₂ O₂ ) is a highly value-added and environmentally friendly chemical with various applications. The production of H₂ O₂ by electrocatalytic 2e^- oxygen reduction reaction (ORR) has drawn considerable research attention, with a view to replacing the currently established anthraquinone process. Electrocatalysts with low cost, high activity, high selectivity, and superior stability are in high demand to realize precise control over electrochemical H₂ O₂ synthesis by 2e^- ORR and the feasible commercialization of this system. This Review introduces a comprehensive overview of non-noble metal-based catalysts for electrochemical oxygen reduction to afford H₂ O₂ , providing an insight into catalyst design and corresponding reaction mechanisms. It starts with an in-depth discussion on the origins of 2e^- /4e^- selectivity towards ORR for catalysts. Recent advances in design strategies for non-noble metal-based catalysts, including carbon nanomaterials and transition metal-based materials, for electrochemical oxygen reduction to H₂ O₂ are then discussed, with an emphasis on the effects of electronic structure, nanostructure, and surface properties on catalytic performance. Finally, future challenges and opportunities are proposed for the further development of H₂ O₂ electrogeneration through 2e^- ORR, from the standpoints of mechanistic studies and practical application.

Ultrafine self-N-doped porous carbon nanofibers with hierarchical pore structure utilizing a biobased chitosan precursor

Ultrafine porous carbon nanofiber network with ~40 nm fiber diameter is realized for the first time utilizing a biobased polymer as carbon precursor. A simple one-step carbonization procedure is applied to convert the electrospun chitosan/poly(ethylene oxide) nanofibers to self-N-doped ultrafine hierarchically porous carbon nanofiber interconnected web. The pore formation process is governed by the immiscible nature of the two polymers and the sacrificial character of poly(ethylene oxide) with low carbon yield at the carbonization temperature (800 °C). The obtained porous scaffold has a high specific surface area (564 m² g^-1), high micro (0.22 cm³ g^-1) as well as meso/macropore volume (0.28 cm³ g^-1). Structural analysis indicates high graphitic content and the existence of turbostratic carbon typical for carbon fibers derived from otherwise synthetic polymer precursors. X-ray photoelectron spectroscopy confirms the presence of an N-doped structure with dominating graphitic N, together with a smaller amount of pyridinic N. The prepared electrode exhibits good electrochemical performance as a supercapacitor device. The excellent charge storage characteristics are attributed to the unique ultrafine hierarchical nanoarchitecture and the interconnected N-doped carbon structure. This green material holds great promise for the realization of more sustainable high-performance energy storage devices.

N-doped honeycomb-like porous carbon derived from biomass as an efficient carbocatalyst for H2S selective oxidation

3D interconnected porous N-doped carbocatalyst derived from the waste air-laid paper plays as an efficient metal-free catalyst for H₂S removal in super-Claus reaction. The honeycomb-like porous nitrogen-doped carbons are fabricated through a facile impregnation of alkaline solution and NH₃ post-treatment method. The experiments prove that NH₃ post-treatment is an efficient way to improve the catalytic performance, which resulting in outstanding reactivity and stability with highest sulfur formation rate of 496.6 g_sulfurkg_cat.^-1 h^-1 and sulfur yield of 86.7 % in feed gas with high concentration (ca. 10,000 ppm) of H₂S for selective oxidation. Significantly, the optimized pyridinic-N content and defect degree endow the N-doped porous carbon (NPC700) with highest catalytic activity according to the Raman and XPS results. The high surface area and abundant porous structure also contribute to the high catalytic performance by increasing the exposure degree of active site and offering additional active surface. Based on the XPS, SEM, TEM and EDS mapping results, the N-doped porous carbon are proved to be stable catalysts since the morphology and surface chemical environment remain similar after the oxidative desulfurization process.

Development of a highly stable Pt-based ORR catalyst over Mn-modified polyaniline-based carbon nanofibers

A highly stable Pt-based ORR catalyst was developed over Mn-modified polyaniline-based carbon nanofibers with a high degree of graphitization.

Graphene-based frustrated Lewis pairs as bifunctional catalysts for CO2 reduction via the dissociative chemisorption of molecular H2: a periodic density functional perspective

Nanocarbon-based frustrated Lewis pair (FLP) bifunctional catalysts, on account of their unquenched electron transfer property, are becoming increasingly attractive as catalysts for the CO₂ reduction reaction via the dissociative chemisorption of H₂.

Investigation of polymer-derived Si-(B)-C-N ceramic/reduced graphene oxide composite systems as active catalysts towards the hydrogen evolution reaction

Hydrogen Evolution Reaction (HER) is an attractive technology for chemical conversion of energy. Replacement of platinum with inexpensive and stable electrocatalysts remains a major bottleneck hampering large-scale hydrogen production by using clean and renewable energy sources. Here, we report electrocatalytically active and ultra-stable Polymer-Derived Ceramics towards HER. We successfully prepared ultrathin silicon and carbon (Si–C) based ceramic systems supported on electrically conducting 2D reduced graphene oxide (rGO) nanosheets with promising HER activity by varying the nature and the composition of the ceramic with the inclusion of nitrogen, boron and oxygen. Our results suggest that oxygen-enriched Si-B-C-N/rGO composites (O-SiBCN/rGO) display the strongest catalytic activity leading to an onset potential and a Tafel slope of − 340 mV and ~ 120 mV dec⁻¹ respectively. O-SiBCN/rGO electrodes display stability over 170 h with minimal increase of 14% of the overpotential compared to ~ 1700% for commercial platinum nanoparticles. Our study provides new insights on the performance of ceramics as affordable and robust HER catalysts calling for further exploration of the electrocatalytic activity of such unconventional materials.

Active Site Engineering in Porous Electrocatalysts

Electrocatalysis is at the center of many sustainable energy conversion technologies that are being developed to reduce the dependence on fossil fuels. The past decade has witnessed significant progresses in the exploitation of advanced electrocatalysts for diverse electrochemical reactions involved in electrolyzers and fuel cells, such as the hydrogen evolution reaction (HER), the oxygen reduction reaction (ORR), the CO₂ reduction reaction (CO₂ RR), the nitrogen reduction reaction (NRR), and the oxygen evolution reaction (OER). Herein, the recent research advances made in porous electrocatalysts for these five important reactions are reviewed. In the discussions, an attempt is made to highlight the advantages of porous electrocatalysts in multiobjective optimization of surface active sites including not only their density and accessibility but also their intrinsic activity. First, the current knowledge about electrocatalytic active sites is briefly summarized. Then, the electrocatalytic mechanisms of the five above-mentioned reactions (HER, ORR, CO₂ RR, NRR, and OER), the current challenges faced by these reactions, and the recent efforts to meet these challenges using porous electrocatalysts are examined. Finally, the future research directions on porous electrocatalysts including synthetic strategies leading to these materials, insights into their active sites, and the standardized tests and the performance requirements involved are discussed.

Polyaniline-Derived N-Doped Ordered Mesoporous Carbon Thin Films: Efficient Catalysts towards Oxygen Reduction Reaction

One of the most challenging targets in oxygen reduction reaction (ORR) electrocatalysts based on N-doped carbon materials is the control of the pore structure and obtaining nanostructured thin films that can easily be incorporated on the current collector. The carbonization of nitrogen-containing polymers and the heat treatment of a mixture of carbon materials and nitrogen precursor are the most common methods for obtaining N-doped carbon materials. However, in this synthetic protocols, the surface area and pore distribution are not controlled. This work enables the preparation of 2D-ordered N-doped carbon materials through the carbonization of 2D polyaniline. For that purpose, aniline has been electropolymerized within the porous structure of two different templates (ordered mesoporous Silica and ordered mesoporous Titania thin films). Thus, aniline has been impregnated into the porous structure and subsequently electropolymerized by means of chronoamperometry at constant potential. The resultant samples were heat-treated at 900 °C with the aim of obtaining 2D N-doped carbon materials within the template structures. Polyaniline and polyaniline-derived carbon materials have been analyzed via XPS and TEM and characterized by electrochemical measurements. It is worth noting that the obtained 2D-ordered mesoporous N-doped carbon materials have proved to be highly active electrocatalysts for the ORR because of the formation of quaternary nitrogen species during the heat treatment.

Co-doped carbon materials synthesized with polymeric precursors as bifunctional electrocatalysts

The design of stable and high performance metal free bifunctional electrocatalysts is a necessity in alkaline zinc–air batteries for oxygen reduction and evolution reaction. In the present work co-doped carbon materials have been developed from polymeric precursors with abundant active sites to achieve bifunctional activity. A 3-dimensional microporous nitrogen–carbon (NC) and co-doped nitrogen–sulfur–carbon (NSC) and nitrogen–phosphorus–carbon (NPC) were synthesized using poly(2,5-benzimidazole) as an N containing precursor. The obtained sheet like structure shows outstanding ORR and OER performance in alkaline systems with excellent stability compared to Pt/C catalyst. The doped heteroatom in the carbon is expected to have redistributed the charge around heteroatom dopants lowering the ORR potential and modifying the oxygen chemisorption mode thereby weakening the O–O bonding and improving the ORR activity and overall catalytic performance. The bifunctional activity (ΔE = E_j=10 − E_1/2) of an air electrode for NPC, NSC, NC and Pt/C is 0.82 V, 0.87 V, 1.06 V and 1.03 V respectively, and the NPC value is smaller than most of the reported metal and non-metal based electrocatalysts. The ORR (from onset potential) and OER (10 mA cm⁻²) overpotential for NPC, NSC, and NC is (290 mV, 410 mV), (310 mV, 450 mV) and (340 mV, 600 mV) respectively. In the prepared catalyst the NPC exhibited higher ORR and OER activity (NPC > NSC > NC). The doping of P in NPC is found to have a great influence on the microstructure and therefore on the ORR and OER activity.

Metal free bifunctional catalysts based on co-doped carbon materials synthesized from polymeric precursors via a simple pyrolysis route with high cyclic stability and low polarization for Zn–air batteries.

Performance improvement of N-doped carbon ORR catalyst via large through-hole structure

N-doped carbon-based materials are crucial electrically conductive additives and non-metal electrocatalysts for the oxygen reduction reaction. At present, many pieces of research are focused on the effects of micropore, mesopore and hierarchical pore structure on the catalytic activity, however, there are few works concerning the role of large-dimension through-hole structure. Hence, in this work, we prepare two kinds of carbon materials with large through-hole structure, i.e. N-doped carbon hollow-spheres and hollow-tubes, as the oxygen reduction catalysts. The synthesis follows template-free morphology-controlled pyrolysis, which is more convenient than the preparation of conventional N-doped nanotubes and graphene. The resultant N-doped carbon hollow-spheres and hollow-tubes evidently enhanced their ORR catalytic activity, remarkable long-term stability and methanol resistance. The large-dimension through-hole structure is found to account for the increase in mass transfer.

Nitrogen-rich graphitic-carbon@graphene as a metal-free electrocatalyst for oxygen reduction reaction

The metal-free nitrogen-doped graphitic-carbon@graphene (Ng-C@G) is prepared from a composite of polyaniline and graphene by a facile polymerization following by pyrolysis for electrochemical oxygen reduction reaction (ORR). Pyrolysis creates a sponge-like with ant-cave-architecture in the polyaniline derived nitrogenous graphitic-carbon on graphene. The nitrogenous carbon is highly graphitized and most of the nitrogen atoms are in graphitic and pyridinic forms with less oxygenated is found when pyrolyzed at 800 °C. The electrocatalytic activity of Ng-C@G-800 is even better than the benchmarked Pt/C catalyst resulting in the higher half-wave potential (8 mV) and limiting current density (0.74 mA cm^-2) for ORR in alkaline medium. Higher catalytic performance is originated from the special porous structure at microscale level and the abundant graphitic- and pyridinic-N active sites at the nanoscale level on carbon-graphene matrix which are beneficial to the high O₂-mass transportation to those accessible sites. Also, it possesses a higher cycle stability resulting in the negligible potential shift and slight oxidation of pyridinic-N with better tolerance to the methanol.

Ultrasound-assisted transformation from waste biomass to efficient carbon-based metal-free pH-universal oxygen reduction reaction electrocatalysts

Efficient carbon-based nitrogen-doped electrocatalysts derived from waste biomass are regarded as a promising alternative to noble metal catalysts for oxygen reduction reaction (ORR), which is crucial to fuel cell performance. Here, coconut palm leaves are employed as the carbon source and a series of nitrogen-doped porous carbons were prepared by virtue of a facile and mild ultrasound-assisted method. The obtained carbon material (ANDC-900-10) conveys excellent pH-universal catalytic activity with onset potentials (E_onset) of 1.01, 0.91 and 0.84 V vs. RHE, half-wave potentials (E_1/2) of 0.87, 0.74 and 0.66 V vs. RHE and limiting current densities (J_L) of 5.50, 5.45 and 4.97 mA cm^-2 in alkaline, neutral and acidic electrolytes, respectively, prevailing over the commercial Pt/C catalyst and, what's more, ANDC-900-10 displays preeminent methanol crossover resistance and long-term stability in the broad pH range (0-13), thanks to its abundant hierarchical nanopores as well as effective nitrogen doping with high-density pyridinic-N and graphitic-N. This work provides sonochemical insight for underpinning the eco-friendly approach to rationally designing versatile metal-free carbon-based catalysts toward the ORR at various pH levels.

Plasma-Treated Ultrathin Ternary FePSe3 Nanosheets as a Bifunctional Electrocatalyst for Efficient Zinc-Air Batteries

Developing novel bifunctional electrocatalysts with advanced oxygen electrocatalytic activity is pivotal for next-generation energy-storage devices. Herein, we present ultrathin oxygen-doped FePSe₃ (FePSe₃-O) nanosheets by Ar/O₂ plasma treatment, with remarkable surface atom reorganization. Such surface atom reorganization generates multiple crystalline-amorphous interfaces that benefit the kinetics of oxygen evolution reaction, achieving a low overpotential of only 261 mV at 10 mA cm^-2 with a small Tafel slope of 41.13 mV dec^-1. Density functional theory calculation indicates that oxygen doping can also modulate the electrical states at the Fermi level with a decreased band gap responsible for the enhanced electrocatalytic performance. Such unique FePSe₃-O nanosheets can be further fabricated as the air cathode in rechargeable liquid zinc-air batteries (ZABs), which deliver a high open circuit potential of 1.47 V, a small charge-discharge voltage gap of 0.80 V, and good cycling stability for more than 800 circles. As a proof of concept, the flexible solid-state ZABs assembled with FePSe₃-O nanosheets as cathode also display a favorable charge-discharge performance, durable stability, and good bendability. This work sheds new insights into the rational design of defect-rich ternary thiophosphate nanosheets by plasma treatment toward enhanced oxygen electrocatalysts in metal-air batteries.

Nanostructured Carbon-Nitrogen-Sulfur-Nickel Networks Derived From Polyaniline as Bifunctional Catalysts for Water Splitting

The development of reliable production routes for sustainable hydrogen (H₂), which is an essential feedstock for industrial processes and energy carrier for fuel cells, is needed. It appears to be an unavoidable alternative to significantly reduce the dependence on conventional energy sources based on fossil fuels without increasing the atmospheric CO₂ levels. Among the different power-to-X scenarios to access high purity H₂, the electrochemical approach based on electrolysis looks to be a promising sustainable solution at both the small and large industrial scales. However, the practical realization of this important opportunity faces several challenges, including the efficient design of cost-effective catalytic materials to be used as a cathode with improved intrinsic and durable activity. In this contribution, we report the design and development of efficient nanostructured catalysts for the electrocatalytic hydrogen evolution reaction (HER) and oxygen evolution reaction (OER) in aqueous media, whereby noble metal-free elements are embedded in a matrix of a conducting polymer, polyaniline (PANI). To increase the electrical conductivity and further the electrocatalytic ability toward HER of the chemically polymerized PANI in the presence of nickel (II) salt (nitrate), the PANI-based materials have first been stabilized at a mild temperature of 250-350°C in air and then carbonized at 800-1,000°C under nitrogen gas to convert the chemical species into nitrogen, sulfur, nickel, and carbon nanostructured networks (CNNs). Different physicochemical (TGA-DSC, Raman spectroscopy, XRD, SEM, EDX, ICP, CHNS, BET, and XPS) and electrochemical (voltammetry and electrochemical impedance spectrometry) methods have been integrated to characterize the as-synthesized CNNs materials and interrogate the relationship of material-to-performance. It has been found that those synthesis conditions allow for the substantial increase of the electrocatalytic performance toward HER and OER in alkaline media in terms of the onset potential and charge transfer resistance and overpotential at the specific activity of 10 milliamps per square centimeter, thus ranking the present materials among the most efficient noble metal-free catalysts and making them possible candidates for integration in practical low-energy consumption alkaline electrolyzers.