Deciphering Metal–Oxide and Metal–Metal Interplay via Surface Organometallic Chemistry: A Case Study with CO2 Hydrogenation to Methanol

Reactivity Switch of Platinum with Gallium: From Reverse Water Gas Shift to Methanol Synthesis

The development of efficient catalysts for the hydrogenation of CO2 to methanol using "green" H2 is foreseen to be a key step to close the carbon cycle. In this study, we show that small and narrowly distributed alloyed PtGa nanoparticles supported on silica, prepared via a surface organometallic chemistry (SOMC) approach, display notable activity for the hydrogenation of CO2 to methanol, reaching a 7.2 molCH3OH h-1 molPt-1 methanol formation rate with a 54% intrinsic CH3OH selectivity. This reactivity sharply contrasts with what is expected for Pt, which favors the reverse water gas shift reaction, albeit with poor activity (2.6 molCO2 h-1 molPt-1). In situ XAS studies indicate that ca. 50% of Ga is reduced to Ga0 yielding alloyed PtGa nanoparticles, while the remaining 50% persist as isolated GaIII sites. The PtGa catalyst slightly dealloys under CO2 hydrogenation conditions and displays redox dynamics with PtGa-GaOx interfaces responsible for promoting both the CO2 hydrogenation activity and methanol selectivity. Further tailoring the catalyst interface by using a carbon support in place of silica enables to improve the methanol formation rate by a factor of ∼5.

Cu(dppf) complexes can be synthesized from Cu-exchanged solids and enable a quantification of the Cu-accessibility by 31P MAS NMR spectroscopy

Herein, we apply three different copper-exchanged materials (Na-[Al]SBA-15, silica, Na-MCM-22) as hosts for a direct synthesis of CuI(1,1'-bis(diphenylphosphino)ferrocene = dppf) complexes in cationic ion exchange position. Using 31P MAS NMR spectroscopy, we show that identical complexes as after ion exchange are generated if the solids are applied as reactants directly. The homogeneity of copper exchanges is evaluated by EDX spectroscopy. Both CuI and CuII result in the formation of complexes, thereby oxidizing dppf. Cu-particles were not reactive. Optimized conditions for a maximized complex formation are identified applying quantitative 31P MAS NMR spectroscopy and ICP-OES. Only accessible copper in cationic position of the solids forms the complexes. This enables a quantification of the amount of copper in mesopores vs. the total copper amount. Thus, besides a new synthesis of the complex a suitable method for quantitative elucidation of the location of copper cations is demonstrated herein.

Tuning Catalytic Activity of CO2 Hydrogenation to C1 Product via Metal Support Interaction Over Metal/Metal Oxide Supported Catalysts

The metal supported catalysts are emerging catalysts that are receiving a lot of attention in CO2 hydrogenation to C1 products. Numerous experiments have demonstrated that the support (usually an oxide) is crucial for the catalytic performance. The support metal oxides are used to aid in the homogeneous dispersion of metal particles, prevent agglomeration, and control morphology owing to the metal support interaction (MSI). MSI can efficiently optimize the structural and electronic properties of catalysts and tune the conversion of key reaction intermediates involved in CO2 hydrogenation, thereby enhancing the catalytic performance. There is an increasing attention is being paid to the promotion effects in the catalytic CO2 hydrogenation process. However, a systematically understanding about the effects of MSI on CO2 hydrogenation to C1 products catalytic performance has not been fully studied yet due to the diversities in catalysts and reaction conditions. Hence, the characteristics and modes of MSI in CO2 hydrogenation to C1 products are elaborated in detail in our work.

Water-Mediated Selectivity Control of CH3 OH versus CO/CH4 in CO2 Photoreduction on Single-Atom Implanted Nanotube Arrays

Controllable methanol production in artificial photosynthesis is highly desirable due to its high energy density and ease of storage. Herein, single atom Fe is implanted into TiO2 /SrTiO3 (TSr) nanotube arrays by two-step anodization and Sr-induced crystallization. The resulting Fe-TSr with both single Fe reduction centers and dominant oxidation facets (001) contributes to efficient CO2 photoreduction and water oxidation for controlled production of CH3 OH and CO/CH4 . The methanol yield can reach to 154.20 µmol gcat -1 h-1 with 98.90% selectivity by immersing all the catalyst in pure water, and the yield of CO/CH4 is 147.48 µmol gcat -1 h-1 with >99.99% selectivity when the catalyst completely outside water. This CH3 OH yield is 50 and 3 times higher than that of TiO2 and TSr and stands among all the state-of-the-art catalysts. The facile gas-solid and gas-liquid-solid phase switch can selectively control CH3 OH production from ≈0% (above H2 O) to 98.90% (in H2 O) via slowly immersing the catalyst into water, where abundant •OH and H2 O around Fe sites play important role in selective CH3 OH production. This work highlights a new insight for water-mediated CO2 photoreduction to controllably produce CH3 OH.

Materials Genes of CO2 Hydrogenation on Supported Cobalt Catalysts: An Artificial Intelligence Approach Integrating Theoretical and Experimental Data

Designing materials for catalysis is challenging because the performance is governed by an intricate interplay of various multiscale phenomena, such as the chemical reactions on surfaces and the materials' restructuring during the catalytic process. In the case of supported catalysts, the role of the support material can be also crucial. Here, we address this intricacy challenge by a symbolic-regression artificial intelligence (AI) approach. We identify the key physicochemical parameters correlated with the measured performance, out of many offered candidate parameters characterizing the materials, reaction environment, and possibly relevant underlying phenomena. Importantly, these parameters are obtained by both experiments and ab initio simulations. The identified key parameters might be called "materials genes", in analogy to genes in biology: they correlate with the property or function of interest, but the explicit physical relationship is not (necessarily) known. To demonstrate the approach, we investigate the CO2 hydrogenation catalyzed by cobalt nanoparticles supported on silica. Crucially, the silica support is modified with the additive metals magnesium, calcium, titanium, aluminum, or zirconium, which results in six materials with significantly different performances. These systems mimic hydrothermal vents, which might have produced the first organic molecules on Earth. The key parameters correlated with the CH3OH selectivity reflect the reducibility of cobalt species, the adsorption strength of reaction intermediates, and the chemical nature of the additive metal. By using an AI model trained on basic elemental properties of the additive metals (e.g., ionization potential) as physicochemical parameters, new additives are suggested. The predicted CH3OH selectivity of cobalt catalysts supported on silica modified with vanadium and zinc is confirmed by new experiments.

Exploiting Organometallic Chemistry to Functionalize Small Cuprous Oxide Colloidal Nanocrystals

The ligand chemistry of colloidal semiconductor nanocrystals mediates their solubility, band gap, and surface facets. Here, selective organometallic chemistry is used to prepare small, colloidal cuprous oxide nanocrystals and to control their surface chemistry by decorating them with metal complexes. The strategy is demonstrated using small (3-6 nm) cuprous oxide (Cu2O) colloidal nanocrystals (NC), soluble in organic solvents. Organometallic complexes are coordinated by reacting the surface Cu-OH bonds with organometallic reagents, M(C6F5)2, M = Zn(II) and Co(II), at room temperature. These reactions do not disrupt the Cu2O crystallinity or nanoparticle size; rather, they allow for the selective coordination of a specific metal complex at the surface. Subsequently, the surface-coordinated organometallic complex is reacted with three different carboxylic acids to deliver Cu-O-Zn(O2CR') complexes. Selective nanocrystal surface functionalization is established using spectroscopy (IR, 19F NMR), thermal gravimetric analyses (TGA), transmission electron microscopy (TEM, EELS), and X-ray photoelectron spectroscopy (XPS). Photoluminescence efficiency increases dramatically upon organometallic surface functionalization relative to that of the parent Cu2O NC, with the effect being most pronounced for Zn(II) decoration. The nanocrystal surfaces are selectively functionalized by both organic ligands and well-defined organometallic complexes; this synthetic strategy may be applicable to many other metal oxides, hydroxides, and semiconductors. In the future, it should allow NC properties to be designed for applications including catalysis, sensing, electronics, and quantum technologies.

Water and Cu+ Synergy in Selective CO2 Hydrogenation to Methanol over Cu-MgO-Al2O3 Catalysts

The CO2 hydrogenation reaction to produce methanol holds great significance as it contributes to achieving a CO2-neutral economy. Previous research identified isolated Cu+ species doping the oxide surface of a Cu-MgO-Al2O3-mixed oxide derived from a hydrotalcite precursor as the active site in CO2 hydrogenation, stabilizing monodentate formate species as a crucial intermediate in methanol synthesis. In this work, we present a molecular-level understanding of how surface water and hydroxyl groups play a crucial role in facilitating spontaneous CO2 activation at Cu+ sites and the formation of monodentate formate species. Computational evidence has been experimentally validated by comparing the catalytic performance of the Cu-MgO-Al2O3 catalyst with hydroxyl groups against that of its hydrophobic counterpart, where hydroxyl groups are blocked using an esterification method. Our work highlights the synergistic effect between doped Cu+ ions and adjacent hydroxyl groups, both of which serve as key parameters in regulating methanol production via CO2 hydrogenation. By elucidating the specific roles of these components, we contribute to advancing our understanding of the underlying mechanisms and provide valuable insights for optimizing methanol synthesis processes.

Unlocking a Dual-Channel Pathway in CO2 Hydrogenation to Methanol over Single-Site Zirconium on Amorphous Silica

Converting CO2 into methanol on a large scale is of great significance in the sustainable methanol economy. Zirconia species are considered to be an essential support in Cu-based catalysts due to their excellent properties for CO2 adsorption and activation. However, the evolution of Zr species during the reaction and the effect of their structure on the reaction pathways remain unclear. Herein, single-site Zr species in an amorphous SiO2 matrix are created by enhancing the Zr-Si interaction in Cu/ZrO2 -SiO2 catalysts. In situ X-ray absorption spectroscopy (XAS) reveals that the coordination environment of single-site Zr is sensitive to the atmosphere and reaction conditions. We demonstrate that the CO2 adsorption occurs preferably on the interface of Cu and single-site Zr rather than on ZrO2 nanoparticles. Methanol synthesis in reverse water-gas-shift (RWGS)+CO-hydro pathway is verified only over single-dispersed Zr sites, whereas the ordinary formate pathway occurs on ZrO2 nanoparticles. Thus, it expands a non-competitive parallel pathway as a supplement to the dominant formate pathway, resulting in the enhancement of Cu activity sixfold and twofold based on Cu/SiO2 and Cu/ZrO2 catalysts, respectively. The establishment of this dual-channel pathway by single-site Zr species in this work opens new horizons for understanding the role of atomically dispersed oxides in catalysis science.

Structure and Role of a Ga-Promoter in Ni-Based Catalysts for the Selective Hydrogenation of CO2 to Methanol

Supported, bimetallic catalysts have shown great promise for the selective hydrogenation of CO2 to methanol. In this study, we decipher the catalytically active structure of Ni-Ga-based catalysts. To this end, model Ni-Ga-based catalysts, with varying Ni:Ga ratios, were prepared by a surface organometallic chemistry approach. In situ differential pair distribution function (d-PDF) analysis revealed that catalyst activation in H2 leads to the formation of nanoparticles based on a Ni-Ga face-centered cubic (fcc) alloy along with a small quantity of GaOx. Structure refinements of the d-PDF data enabled us to determine the amount of both alloyed Ga and GaOx species. In situ X-ray absorption spectroscopy experiments confirmed the presence of alloyed Ga and GaOx and indicated that alloying with Ga affects the electronic structure of metallic Ni (viz., Niδ-). Both the Ni:Ga ratio in the alloy and the quantity of GaOx are found to minimize methanation and to determine the methanol formation rate and the resulting methanol selectivity. The highest formation rate and methanol selectivity are found for a Ni-Ga alloy having a Ni:Ga ratio of ∼75:25 along with a small quantity of oxidized Ga species (0.14 molNi-1). Furthermore, operando infrared spectroscopy experiments indicate that GaOx species play a role in the stabilization of formate surface intermediates, which are subsequently further hydrogenated to methoxy species and ultimately to methanol. Notably, operando XAS shows that alloying between Ni and Ga is maintained under reaction conditions and is key to attaining a high methanol selectivity (by minimizing CO and CH4 formation), while oxidized Ga species enhance the methanol formation rate.

Implications of Ga promotion and metal-oxide interface from tailored PtGa propane dehydrogenation catalysts supported on carbon

Propane Dehydrogenation is a key technology, where Pt-based catalysts have widely been investigated in industry and academia, with development exploring the use of promoters (Sn, Zn, Ga, etc.) and additives (Na, K, Ca, Si, etc.) towards improved catalytic performances. Recent studies have focused on the role of Ga promotion: while computations suggest that Ga plays a key role in enhancing catalytic selectivity and stability of PtGa catalysts through Pt-site isolation as well as morphological changes, experimental evidence are lacking because of the use of oxide supports that prevent more detailed investigation. Here, we develop a methodology to generate Pt and PtGa nanoparticles with tailored interfaces on carbon supports by combining surface organometallic chemistry (SOMC) and specific thermolytic molecular precursors containing or not siloxide ligands. This approach enables the preparation of supported nanoparticles, exhibiting or not an oxide interface, suitable for state-of-the art electron microscopy and XANES characterization. We show that the introduction of Ga enables the formation of homogenously alloyed, amorphous PtGa nanoparticles, in sharp contrast to highly crystalline monometallic Pt nanoparticles. Furthermore, the presence of an oxide interface is shown to stabilize the formation of small particles, at the expense of propene selectivity loss (formation of cracking side-products, methane/ethene), explaining the use of additives such as Na, K and Ca in industrial catalysts.

In-Situ-Formed Potassium-Modified Nickel-Zinc Carbide Boosts Production of Higher Alcohols beyond CH4 in CO2 Hydrogenation

Ni-based catalysts have been widely studied in the hydrogenation of CO2 to CH4 , but selective and efficient synthesis of higher alcohols (C2+ OH) from CO2 hydrogenation over Ni-based catalyst is still challenging due to successive hydrogenation of C1 intermediates leading to methanation. Herein, we report an unprecedented synthesis of C2+ OH from CO2 hydrogenation over K-modified Ni-Zn bimetal catalyst with promising activity and selectivity. Systematic experiments (including XRD, in situ spectroscopic characterization) and computational studies reveal the in situ generation of an active K-modified Ni-Zn carbide (K-Ni3 Zn1 C0.7 ) by carburization of Zn-incorporated Ni0 , which can significantly enhance CO2 adsorption and the surface coverage of alkyl intermediates, and boost the C-C coupling to C2+ OH rather than conventional CH4 . This work opens a new catalytic avenue toward CO2 hydrogenation to C2+ OH, and also provides an insightful example for the rational design of selective and efficient Ni-based catalysts for CO2 hydrogenation to multiple carbon products.

Combining Atomic Layer Deposition with Surface Organometallic Chemistry to Enhance Atomic-Scale Interactions and Improve the Activity and Selectivity of Cu-Zn/SiO2 Catalysts for the Hydrogenation of CO2 to Methanol

The direct synthesis of methanol via the hydrogenation of CO2, if performed efficiently and selectively, is potentially a powerful technology for CO2 mitigation. Here, we develop an active and selective Cu-Zn/SiO2 catalyst for the hydrogenation of CO2 by introducing copper and zinc onto dehydroxylated silica via surface organometallic chemistry and atomic layer deposition, respectively. At 230 °C and 25 bar, the optimized catalyst shows an intrinsic methanol formation rate of 4.3 g h-1 gCu-1 and selectivity to methanol of 83%, with a space-time yield of 0.073 g h-1 gcat-1 at a contact time of 0.06 s g mL-1. X-ray absorption spectroscopy at the Cu and Zn K-edges and X-ray photoelectron spectroscopy studies reveal that the CuZn alloy displays reactive metal support interactions; that is, it is stable under H2 atmosphere and unstable under conditions of CO2 hydrogenation, indicating that the dealloyed structure contains the sites promoting methanol synthesis. While solid-state nuclear magnetic resonance studies identify methoxy species as the main stable surface adsorbate, transient operando diffuse reflectance infrared Fourier transform spectroscopy indicates that μ-HCOO*(ZnOx) species that form on the Cu-Zn/SiO2 catalyst are hydrogenated to methanol faster than the μ-HCOO*(Cu) species that are found in the Zn-free Cu/SiO2 catalyst, supporting the role of Zn in providing a higher activity in the Cu-Zn system.

Group 10 Metal Allyl Amidinates: A Family of Readily Accessible and Stable Molecular Precursors to Generate Supported Nanoparticles

The synthesis of well-defined materials as model systems for catalysis and related fields is an important pillar in the understanding of catalytic processes at a molecular level. Various approaches employing organometallic precursors have been developed and established to make monodispersed supported nanoparticles, nanocrystals, and films. Using rational design principles, a new family of precursors based on group 10 metals suitable for the generation of small and monodispersed nanoparticles on metal oxides has been developed. Particle formation on SiO2 and Al2O3 supports is demonstrated, as well as the potential in the synthesis of bimetallic catalyst materials, exemplified by a PdGa/SiO2 system capable of hydrogenation of CO2 to methanol. In addition to surface organometallic chemistry (SOMC), it is envisioned that these precursors could also be employed in related applications, such as atomic layer deposition, due to their inherent volatility and relative thermal stability.

Surface Redox Dynamics in Gold-Zinc CO2 Hydrogenation Catalysts

Au-Zn catalysts have previously been shown to promote the hydrogenation of CO₂ to methanol, but their active state is poorly understood. Here, silica-supported bimetallic Au-Zn alloys, prepared by surface organometallic chemistry (SOMC), are shown to be proficient catalysts for hydrogenation of CO₂ to methanol. In situ X-ray absorption spectroscopy (XAS), in conjunction with gas-switching experiments, is used to amplify subtle changes occurring at the surface of this tailored catalyst during reaction. Consequently, an Au-Zn alloy is identified and is shown to undergo subsequent reversible redox changes under reaction conditions according to multivariate curve resolution alternating least-squares (MCR-ALS) analysis. These results highlight the role of alloying and dealloying in Au-based CO₂ hydrogenation catalysts and illustrate the role of these reversible processes in driving reactivity.

The promotional role of Mn in CO2 hydrogenation over Rh-based catalysts from a surface organometallic chemistry approach

Rh-based catalysts modified by transition metals have been intensively studied for CO₂ hydrogenation due to their high activity. However, understanding the role of promoters at the molecular level remains challenging due to the ill-defined structure of heterogeneous catalysts. Here, we constructed well-defined RhMn@SiO₂ and Rh@SiO₂ model catalysts via surface organometallic chemistry combined with thermolytic molecular precursor (SOMC/TMP) approach to rationalize the promotional effect of Mn in CO₂ hydrogenation. We show that the addition of Mn shifts the products from almost pure CH₄ to a mixture of methane and oxygenates (CO, CH₃OH, and CH₃CH₂OH) upon going from Rh@SiO₂ to RhMn@SiO₂. In situ X-ray absorption spectroscopy (XAS) confirms that the Mn^II is atomically dispersed in the vicinity of metallic Rh nanoparticles and enables to induce the oxidation of Rh to form the Mn-O-Rh interface under reaction conditions. The formed interface is proposed to be key to maintaining Rh⁺ sites, which is related to suppressing the methanation reaction and stabilizing the formate species as evidenced by in situ DRIFTS to promote the formation of CO and alcohols.

Bimetallic Sites for Catalysis: From Binuclear Metal Sites to Bimetallic Nanoclusters and Nanoparticles

Heterogeneous bimetallic catalysts have broad applications in industrial processes, but achieving a fundamental understanding on the nature of the active sites in bimetallic catalysts at the atomic and molecular level is very challenging due to the structural complexity of the bimetallic catalysts. Comparing the structural features and the catalytic performances of different bimetallic entities will favor the formation of a unified understanding of the structure-reactivity relationships in heterogeneous bimetallic catalysts and thereby facilitate the upgrading of the current bimetallic catalysts. In this review, we will discuss the geometric and electronic structures of three representative types of bimetallic catalysts (bimetallic binuclear sites, bimetallic nanoclusters, and nanoparticles) and then summarize the synthesis methodologies and characterization techniques for different bimetallic entities, with emphasis on the recent progress made in the past decade. The catalytic applications of supported bimetallic binuclear sites, bimetallic nanoclusters, and nanoparticles for a series of important reactions are discussed. Finally, we will discuss the future research directions of catalysis based on supported bimetallic catalysts and, more generally, the prospective developments of heterogeneous catalysis in both fundamental research and practical applications.

Probing the Nature of Zinc in Copper-Zinc-Zirconium Catalysts by Operando Spectroscopies for CO2 Hydrogenation to Methanol

Active Zn species in Cu-based methanol synthesis catalysts have not been clearly identified yet due to their complex nature and dynamic structural changes during reactions. Herein, atomically dispersed Zn on ZrO₂ support is established in Cu-based catalysts by separating Zn and Zr components from Cu (Cu-ZnZr) via the double-nozzle flame spray pyrolysis (DFSP) method. It exhibits superiority in methanol selectivity and yield compared to those with Cu-ZnO interface and isolated ZnO nanoparticles. Operando X-ray absorption spectroscopy (XAS) reveals that the atomically dispersed Zn species are induced during the reaction due to the strengthened Zn-Zr interaction. They can suppress formate decomposition to CO and decrease the H₂ dissociation energy, shifting the reaction to methanol production. This work enlightens the rational design of unique Zn species by regulating coordination environments and offers a new perspective for exploring complex interactions in multi-component catalysts.

Data-Centric Heterogeneous Catalysis: Identifying Rules and Materials Genes of Alkane Selective Oxidation

Artificial intelligence (AI) can accelerate catalyst design by identifying key physicochemical descriptive parameters correlated with the underlying processes triggering, favoring, or hindering the performance. In analogy to genes in biology, these parameters might be called "materials genes" of heterogeneous catalysis. However, widely used AI methods require big data, and only the smallest part of the available data meets the quality requirement for data-efficient AI. Here, we use rigorous experimental procedures, designed to consistently take into account the kinetics of the catalyst active states formation, to measure 55 physicochemical parameters as well as the reactivity of 12 catalysts toward ethane, propane, and n-butane oxidation reactions. These materials are based on vanadium or manganese redox-active elements and present diverse phase compositions, crystallinities, and catalytic behaviors. By applying the sure-independence-screening-and-sparsifying-operator symbolic-regression approach to the consistent data set, we identify nonlinear property-function relationships depending on several key parameters and reflecting the intricate interplay of processes that govern the formation of olefins and oxygenates: local transport, site isolation, surface redox activity, adsorption, and the material dynamical restructuring under reaction conditions. These processes are captured by parameters derived from N₂ adsorption, X-ray photoelectron spectroscopy (XPS), and near-ambient-pressure in situ XPS. The data-centric approach indicates the most relevant characterization techniques to be used for catalyst design and provides "rules" on how the catalyst properties may be tuned in order to achieve the desired performance.

Illustrating new understanding of adsorbed water on silica for inducing tetrahedral cobalt(II) for propane dehydrogenation

Highly dispersed metal sites on the surface of silica, achieved from immobilization of metal precursor within hydroxyl groups, has gained increasing attention in the field of heterogeneous catalyst. However, the special role of adsorbed water derived by hydroxyl groups on the silica is generally ignored. Herein, a new understanding of adsorbed water on the formation of highly dispersed tetrahedral Co(II) (T_d-cobalt(II)) sites is illustrated. It is indicated that sufficient adsorbed water induces the transformation of precursor of Co(NO₃)₂ into intermediate of [Co(H₂O)₆]²⁺. Subsequently, [Co(H₂O)₆]²⁺ makes the highly dispersed T_d-cobalt(II) sites to be available during direct H₂-reduction process. A systematic characterization and DFT calculation prove the existence of the adsorbed water and the importance of the intermediate of [Co(H₂O)₆]²⁺, respectively. The as-synthesized catalyst is attempted to the propane dehydrogenation, which shows better reactivity when compared with other reported Co based catalysts.

Ga and Zn increase the oxygen affinity of Cu-based catalysts for the CO x hydrogenation according to ab initio atomistic thermodynamics

The direct hydrogenation of CO or CO₂ to methanol, a highly vivid research area in the context of sustainable development, is typically carried out with Cu-based catalysts. Specific elements (so-called promoters) improve the catalytic performance of these systems under a broad range of reaction conditions (from pure CO to pure CO₂). Some of these promoters, such as Ga and Zn, can alloy with Cu and their role remains a matter of debate. In that context, we used periodic DFT calculations on slab models and ab initio thermodynamics to evaluate both metal alloying and surface formation by considering multiple surface facets, different promoter concentrations and spatial distributions as well as adsorption of several species (O*, H*, CO* and ) for different gas phase compositions. Both Ga and Zn form an fcc-alloy with Cu due to the stronger interaction of the promoters with Cu than with themselves. While the Cu-Ga-alloy is more stable than the Cu-Zn-alloy at low promoter concentrations (<25%), further increasing the promoter concentration reverses this trend, due to the unfavoured Ga-Ga-interactions. Under CO₂ hydrogenation conditions, a substantial amount of O* can adsorb onto the alloy surfaces, resulting in partial dealloying and oxidation of the promoters. Therefore, the CO₂ hydrogenation conditions are actually rather oxidising for both Ga and Zn despite the large amount of H₂ present in the feedstock. Thus, the growth of a GaO _x /ZnO _x overlayer is thermodynamically preferred under reaction conditions, enhancing CO₂ adsorption, and this effect is more pronounced for the Cu-Ga-system than for the Cu-Zn-system. In contrast, under CO hydrogenation conditions, fully reduced and alloyed surfaces partially covered with H* and CO* are expected, with mixed CO/CO₂ hydrogenation conditions resulting in a mixture of reduced and oxidised states. This shows that the active atmosphere tunes the preferred state of the catalyst, influencing the catalytic activity and stability, indicating that the still widespread image of a static catalyst under reaction conditions is insufficient to understand the complex interplay of processes taking place on a catalyst surface under reaction conditions, and that dynamic effects must be considered.

Flame-made Cu/ZrO2 catalysts with metastable phase and strengthened interactions for CO2 hydrogenation to methanol

Facile synthesis of a highly efficient Cu/ZrO2 catalyst by a flame spray pyrolysis (FSP) method was developed for methanol production from CO2 hydrogenation. The instantaneous quenching process from extremely high temperature in FSP was used for rational design of a Cu/ZrO2 catalyst, not only producing the metastable tetragonal phase ZrO2, but also strengthening the metal-support interaction. The methanol yield of one-step synthesized FSP-Cu/ZrO2 was 3 times higher than the one made by the traditional method. This strategy is anticipated to pave the way for strengthening metal-support interactions of supported catalysts.