Sub-4 nm PtZn Intermetallic Nanoparticles for Enhanced Mass and Specific Activities in Catalytic Electrooxidation Reaction

Ligand Effect of PdRu on Pt-Enriched Surface for Glucose Complete Electro-Oxidation to Carbon Dioxide and Abiotic Direct Glucose Fuel Cells

The development of advanced electrocatalysts for the abiotic direct glucose fuel cells (ADGFCs) is critical in the implantable devices in living organisms. The ligand effect in the Pt shell-alloy core nanocatalysts is known to influence the electrocatalytic reaction in interfacial structure. Herein, we reported the synthesis of ternary Pt@PdRu nanoalloy aerogels with ligand effect of PdRu on Pt-enriched surface through electrochemical cycling. Pt@PdRu aerogels with optimized Pt surface electronic structure exhibited high mass activity and specific activity of Pt@PdRu about 450 mA mgPt -1 and 1.09 mA cm-2, which were 1.4 and 1.6 times than that of commercial Pt/C. Meanwhile, Pt@PdRu aerogels have higher electrochemical stability comparable to commercial Pt/C. In-situ FTIR spectra results proved that the glucose oxidation reaction on Pt@PdRu aerogels followed the CO-free direct pathway reaction mechanism and part of the products are CO2 by completed oxidation. Furthermore, the ADGFC with Pt@PdRu ultrathin anode catalyst layer showed a much higher power density of 6.2 mW cm-2 than commercial Pt/C (3.8 Mw cm-2). To simulate the blood fuel cell, the Pt@PdRu integrated membrane electrode assembly was exposed to glucose solution and a steady-state open circuit of approximately 0.6 V was achieved by optimizing the glucose concentration in cell system.

Anion-Exchange Membranes' Characteristics and Catalysts for Alkaline Anion-Exchange Membrane Fuel Cells

This work aims at the effects of anion-exchange membranes (AEMs) and ionomer binders on the catalyst electrodes for anion-exchange membrane fuel cells (AEMFCs). In the experiments, four metal catalysts (nano-grade Pt, PtRu, PdNi and Ag), four AEMs (aQAPS-S8, AT-1, X37-50T and X37-50RT) and two alkaline ionomers (aQAPS-S14 and XB-7) were used. They were verified through several technical parameters examination and cell performance comparison for the optimal selection of AMEs. The bimetallic PdNi nanoparticles (PdNi/C) loaded with Vulcan XC-72R carbon black were used as anode electrodes by using the wet impregnation method, and Ag nanoparticles (Ag/C) were used as the catalyst cathode. It was found that the power density and current density of the X37-50RT are higher than the other three membranes. Also, alkaline ionomers of XB-7 had better performance than aQAPS-S14. The efficiency was improved by 32%, 155% and 27%, respectively, when compared to other membranes by using the same catalyst of PdNi/C, Ag/C and Pt/C. The results are consistent with the membrane ion conductivity measurements, which showed that the conductivity of the X37-50RT membrane is the highest among them. The conductivity values for hydroxide ions (OH-) and bromide ions (Br-) are 131 mS/cm and 91 mS/cm, respectively. These findings suggest that the properties (water uptake, swelling rate and mechanical) of the anion-exchange membrane (AEM) can serve as a key reference for AEM fuel cell applications.

Modification Strategies for Development of 2D Material-Based Electrocatalysts for Alcohol Oxidation Reaction

2D materials, such as graphene, MXenes (metal carbides and nitrides), graphdiyne (GDY), layered double hydroxides, and black phosphorus, are widely used as electrocatalyst supports for alcohol oxidation reactions (AORs) owing to their large surface area and unique 2D charge transport channels. Furthermore, the development of highly efficient electrocatalysts for AORs via tuning the structure of 2D support materials has recently become a hot area. This article provides a critical review on modification strategies to develop 2D material-based electrocatalysts for AOR. First, the principles and influencing factors of electrocatalytic oxidation of alcohols (such as methanol and ethanol) are introduced. Second, surface molecular functionalization, heteroatom doping, and composite hybridization are deeply discussed as the modification strategies to improve 2D material catalyst supports for AORs. Finally, the challenges and perspectives of 2D material-based electrocatalysts for AORs are outlined. This review will promote further efforts in the development of electrocatalysts for AORs.

Edge-Rich Pt-O-Ce Sites in CeO2 Supported Patchy Atomic-Layer Pt Enable a Non-CO Pathway for Efficient Methanol Oxidation

Rational design of efficient methanol oxidation reaction (MOR) catalyst that undergo non-CO pathway is essential to resolve the long-standing poisoning issue. However, it remains a huge challenge due to the rather difficulty in maximizing the non-CO pathway by the selective coupling between the key *CHO and *OH intermediates. Here, we report a high-performance electrocatalyst of patchy atomic-layer Pt epitaxial growth on CeO2 nanocube (Pt ALs/CeO2) with maximum electronic metal-support interaction for enhancing the coupling selectively. The small-size monolayer material achieves an optimal geometrical distance between edge Pt-O-Ce sites and *OH absorbed on CeO2, which well restrains the dehydrogenation of *CHO, resulting in the non-CO pathway. Meanwhile, the *CHO/*CO intermediate generated at inner Pt-O-Ce sites can migrate to edge, inducing the subsequent coupling reaction, thus avoiding poisoning while promoting reaction efficiency. Consequently, Pt ALs/CeO2 exhibits exceptionally catalytic stability with negligible degradation even under 1000 s pure CO poisoning operation and high mass activity (14.87 A/mgPt), enabling it one of the best-performing alkali-stable MOR catalysts.

Metal bond strength regulation enables large-scale synthesis of intermetallic nanocrystals for practical fuel cells

Structurally ordered L10-PtM (M = Fe, Co, Ni and so on) intermetallic nanocrystals, benefiting from the chemically ordered structure and higher stability, are one of the best electrocatalysts used for fuel cells. However, their practical development is greatly plagued by the challenge that the high-temperature (>600 °C) annealing treatment necessary for realizing the ordered structure usually leads to severe particle sintering, morphology change and low ordering degree, which makes it very difficult for the gram-scale preparation of desirable PtM intermetallic nanocrystals with high Pt content for practical fuel cell applications. Here we report a new concept involving the low-melting-point-metal (M' = Sn, Ga, In)-induced bond strength weakening strategy to reduce Ea and promote the ordering process of PtM (M = Ni, Co, Fe, Cu and Zn) alloy catalysts for a higher ordering degree. We demonstrate that the introduction of M' can reduce the ordering temperature to extremely low temperatures (≤450 °C) and thus enable the preparation of high-Pt-content (≥40 wt%) L10-Pt-M-M' intermetallic nanocrystals as well as ten-gram-scale production. X-ray spectroscopy studies, in situ electron microscopy and theoretical calculations reveal the fundamental mechanism of the Sn-facilitated ordering process at low temperatures, which involves weakened bond strength and consequently reduced Ea via Sn doping, the formation and fast diffusion of low-coordinated surface free atoms, and subsequent L10 nucleation. The developed L10-Ga-PtNi/C catalysts display outstanding performance in H2-air fuel cells under both light- and heavy-duty vehicle conditions. Under the latter condition, the 40% L10-Pt50Ni35Ga15/C catalyst delivers a high current density of 1.67 A cm-2 at 0.7 V and retains 80% of the current density after extended 90,000 cycles, which exceeds the United States Department of Energy performance metrics and represents among the best cathodic electrocatalysts for practical proton-exchange membrane fuel cells.

In-situ atomic tracking of intermetallic compound formation during thermal annealing

Intermetallic compounds (IMCs) with ordered atomic structure have gained great attention as nanocatalysts for its enhanced activity and stability. Although the reliance of IMC preparation on high-temperature annealing is well known, a comprehensive understanding of the formation mechanisms of IMCs in this process is currently lacking. Here, we employ aberration-corrected high-angle annular dark-field scanning transmission electron microscopy (AC-HAADF-STEM) to track the formation process of IMCs on carbon supports during in-situ annealing, by taking PtFe as a case study within an industry-relevant impregnation synthesis framework. We directly discern five different stages at the atomic level: initial atomic precursors; Pt cluster formation; Pt-Fe disordered alloying; structurally ordered Pt3Fe formation, and final Pt3Fe-PtFe IMC conversion. In particular, we find that the crucial role of high-temperature annealing resides in facilitating the diffusion of Fe towards Pt, enabling the creation of alloys with the targeted stoichiometric ratio, which in turn provides the thermodynamic driving force for the disorder-to-order transition.

PtRu mesoporous nanospheres as electrocatalysts with enhanced performance for oxidation of methanol

Composition and morphology are crucial factors in the design of Pt-based catalysts with high performance, particularly in direct methanol fuel cells (DMFCs). Herein, PtRu mesoporous nanospheres (PtRu MNs) with tunable compositions were synthesized via a facile method and then deposited on a carbon support to act as electrocatalyst materials for the methanol oxidation reaction (MOR). Superior catalytic activity, better catalytic stability, and good tolerance to CO were achieved by the optimum PtRu (2 : 1) MNs/C catalyst compared with Pt MNs/C. The mass activity on PtRu (2 : 1) MNs/C reached 111.77 mA mgPt -1, which was approximately 6.45-fold higher than that of Pt MNs/C (17.33 mA mgPt -1). Meanwhile, PtRu (2 : 1) MNs/C retained much more current density (84.7%) than Pt MNs/C (17.7%) after 500 cycles. The improved catalytic performance is due to several factors, including the formation of a mesoporous nanostructure with abundant active sites and the favorable effects of the Ru species. This work provides guidance toward designing and fabricating effective Pt-based electrocatalysts for DMFC applications.

Designing the framework structure of noble-metal based nanoalloy catalysts driving redox electrocatalysis

Noble metal-based nanoalloys (NAs) with different entropies have great potential in the field of energy and catalysis. However, it is still very difficult for the reported synthesis strategies to achieve the universal synthesis of small-sized alloys with controllable morphology. Here we develop a general synthesis strategy that combined cation exchange and spatial confinement (CESC). We used this method to construct a library with 21 NAs having low to high entropies. Importantly, we also demonstrate that the method can controllably achieve framing of almost all the NAs obtained, which can be realized by adjusting the amount of non-precious metals, despite the differences in the number of elements. Moreover, the CESC method showed outstanding ability to suppress the sintering of NAs and regulate the particle size of NAs. In the NA library, the framed PtCu/HCN as a redox electrocatalyst shows superior properties. For the methanol oxidation reaction (MOR), the specific and mass activities (7.02 mA cm-2 and 2.81 A mgPt -1) of PtCu/HCN show 28.1- and 13.4-fold enhancement compared to those of commercial Pt/C, and the peak current density is only attenuated by 5% after 50k seconds of chronoamperometry. For the hydrogen evolution reaction (HER), it can operate at ultralow overpotential (23.5 mV and 10 mA cm-2) for 150 h, far exceeding most of the reported catalysts. Moreover, the catalyst is capable of long-term hydrogen evolution at ultra-low overpotentials. Our work offers opportunities for synthesizing framed superfine noble metal-based NAs with different entropies.

VOx Matrix Confinement Approach to Generate Sub-3 nm L10-Pt-Based Intermetallic Catalysts for Fuel Cell Cathode

Pt-based intermetallic compounds (IMCs) are considered as a class of promising fuel cell electrocatalysts, owing to their outstanding intrinsic activity and durability. However, the synthesis of uniformly dispersed IMCs with small sizes presents a formidable challenge during the essential high-temperature annealing process. Herein, a facile and generally applicable VOx matrix confinement strategy is demonstrated for the controllable synthesis of ordered L10-PtM (M = Fe, Co, and Mn) nanoparticles, which not only enhances the dispersion of intermetallic nanocrystals, even at high loading (40 wt%), but also simplifies the oxide removal and acid-washing procedures. Taking intermetallic PtCo as an example, the as-prepared catalyst displays a high-performance oxygen reduction activity (mass activity of 1.52 A mgPt -1) and excellent stability in the membrane electrode assemblies (MEAs) (the ECSA has just 7% decay after durability test). This strategy provides an economical and scalable route for the controlled synthesis of Pt-based intermetallic catalysts, which can pave a way for the commercialization of fuel cell technologies.

Pt1.8Pd0.2CuGa Intermetallic Nanocatalysts with Enhanced Methanol Oxidation Performance for Efficient Hybrid Seawater Electrolysis

Seawater electrolysis is a potentially cost-effective approach to green hydrogen production, but it currently faces substantial challenges for its high energy consumption and the interference of chlorine evolution reaction (ClER). Replacing the energy-demanding oxygen evolution reaction with methanol oxidation reaction (MOR) represents a promising alternative, as MOR occurs at a significantly low anodic potential, which cannot only reduce the voltage needed for electrolysis but also completely circumvents ClER. To this end, developing high-performance MOR catalysts is a key. Herein, a novel quaternary Pt1.8Pd0.2CuGa/C intermetallic nanoparticle (i-NP) catalyst is reported, which shows a high mass activity (11.13 A mgPGM -1), a large specific activity (18.13 mA cmPGM -2), and outstanding stability toward alkaline MOR. Advanced characterization and density functional theory calculations reveal that the introduction of atomically distributed Pd in Pt2CuGa intermetallic markedly promotes the oxidation of key reaction intermediates by enriching electron concentration around Pt sites, resulting in weak adsorption of carbon-containing intermediates and favorable adsorption of synergistic OH- groups near Pd sites. MOR-assisted seawater electrolysis is demonstrated, which continuously operates under 1.23 V for 240 h in simulated seawater and 120 h in natural seawater without notable degradation.

Pt3Sn0.5Mn0.5 Intermetallic Electrocatalyst with Superior Stability for CO-Resilient Methanol Oxidation

The sluggish kinetics of methanol oxidation reaction (MOR) and poor long-term durability of catalysts are the main restrictions of the large-scale applications of direct methanol fuel cells (DMFCs). Herein, we demonstrated an inspirational ternary Pt3Sn0.5Mn0.5/DMC intermetallic catalyst that reached 4.78 mA cm-2 and 2.39 A mg-1Pt for methanol oxidation, which were 2.50/2.44 and 5.62/5.31 times that of commercial PtRu/C and Pt/C. After the durability test, Pt3Sn0.5Mn0.5/DMC presented a very low current density attenuation (38.5%), which was significantly lower than those for commercial PtRu/C catalyst (84.2%) and Pt/C (93.1%). Density functional theory (DFT) calculations revealed that the coregulation of Sn and Mn altered the surface electronic structure and endowed Pt3Sn0.5Mn0.5 with selective adsorption of Pt for CO and Sn for OH, which optimized the adsorption strength for intermediates and improved the reaction kinetics of MOR. Beyond offering an advanced electrocatalyst, this study provided a new point of view for the rational design of superior methanol oxidation catalysts for DMFC.

Gram-scale synthesis of small-sized PtM intermetallics as high-performance catalysts for the hydrogen evolution reaction

Pt-based intermetallics exhibit excellent activity in electrocatalysis. However, their controlled syntheses remain difficult. Herein, carbon-supported PtM (M = Fe, Co, Ni, Zn and Mn) intermetallics with small size (3 nm) were prepared at the gramscale and applied as a highly effective electrocatalyst for the hydrogen evolution reaction.

Site-selective sulfur anchoring produces sintering-resistant intermetallic ORR electrocatalysts for membrane electrode assemblies

Intermetallic compounds are emerging as promising oxygen reduction reaction (ORR) catalysts for fuel cells due to their typically higher activity and durability compared to disordered alloys. However, the preparation of intermetallic catalysts often requires high-temperature annealing, which unfortunately leads to adverse sintering of the metal nanoparticles. Herein, we develop a scalable site-selective sulfur anchoring strategy that effectively suppresses alloy sintering, ensuring the formation of efficient intermetallic electrocatalysts with small sizes and high ordering degrees. The alloy-support interactions are precisely modulated by selectively modifying the alloy-support interfaces with oxidized sulfur species, thus simultaneously blocking both the nanoparticle migration and Oswald ripening pathways for sintering. Using this strategy, sub-5 nm PtCo intermetallic electrocatalysts enclosed by two atomic layers of Pt shells have been successfully prepared even at a metal loading higher than 30 wt%. The intermetallic catalysts exhibit excellent ORR performances in both rotating disk electrode and membrane electrode assembly conditions with a mass activity of 1.28 A mgPt-1 at 0.9 V (vs. RHE) and a power density of 1.0 W cm-2 at a current density of 1.5 A cm-2. The improved performances result from the enhanced Pt-Co electronic interactions and compressive surface strain generated by the highly ordering structure, while the atomic Pt shells prevent the dissolution of Co under highly acidic conditions. This work provides new insights to inhibit the sintering of nanoalloys and would promote the scalable synthesis and applications of platinum-based intermetallic catalysts.

Engineering a High-Loading Sub-4 nm Intermetallic Platinum-Cobalt Alloy on Atomically Dispersed Cobalt-Nitrogen-Carbon for Efficient Oxygen Reduction in Fuel Cells

Developing a high-performance membrane electrode assembly (MEA) poses a formidable challenge for fuel cells, which lies in achieving both high metal loading and efficient catalytic activity concurrently for MEA catalysts. Here, we introduce a porous Co@NC carrier to synthesize sub-4 nm PtCo intermetallic nanocrystals, achieving an impressive Pt loading of 27 wt %. The PtCo-CoNC catalyst demonstrates exceptional catalytic activity and remarkable stability for the oxygen reduction reaction. Advanced characterization techniques and theoretical calculations emphasize the synergistic effect between PtCo alloys and single Co atoms, which enhances the desorption of the OH* intermediate. Furthermore, the PtCo-CoNC-based cathode delivers a high power density of 1.22 W cm-2 in the MEA test owing to the enhanced mass transport, which is verified by the simulation results of the O2 distributions and current density inside the catalyst layer. This study lays the groundwork for the design of efficient catalysts with practical applications in fuel cells.

Thermally induced intermetallic Rh1Zn1 nanoparticles with high phase-purity for highly selective hydrogenation of acetylene

Ordered M1Zn1 intermetallic phases with structurally isolated atom sites offer unique electronic and geometric structures for catalytic applications, but lack reliable industrial synthesis methods that avoid forming a disordered alloy with ill-defined composition. We developed a facile strategy for preparing well-defined M1Zn1 intermetallic nanoparticle (i-NP) catalysts from physical mixtures of monometallic M/SiO2 (M = Rh, Pd, Pt) and ZnO. The Rh1Zn1 i-NPs with structurally isolated Rh atom sites had a high intrinsic selectivity to ethylene (91%) with extremely low C4 and oligomer formation, outperforming the reported intermetallic and alloy catalysts in acetylene semihydrogenation. Further studies revealed that the M1Zn1 phases were formed in situ in a reducing atmosphere at 400 °C by a Zn atom emitting-trapping-ordering (Zn-ETO) mechanism, which ensures the high phase-purity of i-NPs. This study provides a scalable and practical solution for further exploration of Zn-based intermetallic phases and a new strategy for designing Zn-containing catalysts.

Emerging Pt-based intermetallic nanoparticles for the oxygen reduction reaction

The advancement of highly efficient and enduring platinum (Pt)-based electrocatalysts for the oxygen reduction reaction (ORR) is a critical determinant to enable broad utilization of clean energy conversion technologies. Pt-based intermetallic electrocatalysts offer durability and superior ORR activity over their traditional analogues due to their definite stoichiometry, ordered and extended structures, and favourable enthalpy of formation. With the advent in new synthetic methods, Pt-based intermetallic nanoparticles as a new class of advanced electrocatalysts have been studied extensively in recent years. This review discusses the preparation principles, representative preparation methods of Pt-based intermetallics and their applications in the ORR. Our review is focused on L10 Pt-based intermetallics which have gained tremendous interest recently due to their larger surface strain and enhanced M(3d)-Pt(5d) orbital coupling, particularly in the crystallographic c-axis direction. Additionally, we discuss future research directions to further improve the efficiency of Pt-based intermetallic electrocatalysts with the intention of stimulating increased research ventures in this domain.

Two-stage confinement derived small-sized highly ordered L10-PtCoZn for effective oxygen reduction catalysis in PEM fuel cells

Intermetallic ordered PtCo is effective for high oxygen reduction reaction (ORR) activity and stability. However, preparing small-sized, highly ordered PtM alloys is still challenging. Herein, we report a controlled two-stage confinement strategy, in which highly ordered PtCoZn/NC nanoparticles of 5.3 nm size were prepared in a scalable process. The contradiction between the high ordering degree with the small particle size as well as the atomic migration with the space confinement was well resolved. An outstanding PEMFC performance was achieved for L10-PtCoZn/NC with a high mass activity (MA) of 1.21 A/mgPt at 0.9 ViR-free, 80.1 % MA retention after 30 k cycles in H2-O2 operation, and a high mass-specific power density of 8.24 W mg-1Pt in H2-Air operation with a slight loss of cell voltage@0.8 A cm-2 of 28 mV after 30 k cycles. The high performance can be ascribed to the high Pt area exposure, the enhanced Pt-Co coupling, and the prevented agglomeration in the mesoporous carbon wall. Overall, this strategy may contribute to the commercialization of fuel cells.

Gas-phase hydrogenation of furfural into value-added chemicals: The critical role of metal-based catalysts

Furfural (FF: aldehyde derivable from lignocellulosic biomass) has been widely recognized as a versatile building block for eco-friendly and sustainable applications to reduce industrial reliance on fossil-fuel carbon sources. Hydrogenation of FF, in particular, is recognized as one of the most effective routes for producing various value-added chemicals (e.g., furfuryl alcohol and 2-methylfuran). The gas-phase FF hydrogenation reaction offers economic and environmental advantages over its liquid-phase counterpart in conversion efficiency, product selectivity, and kinetics. The operation of the former does not require high hydrogen pressures or hazardous solvents while not generating undesirable by-products (due to reduced selectivity toward the ring-opening reaction). In this context, the utility of noble and non-noble metal catalyst systems has been recognized for their potential to induce effective FF hydrogenation in the gas phase. The present review addresses current understandings and recent developments in research on gas-phase FF hydrogenation and the factors governing the performance of metal-based catalysts (e.g., materials and surface chemistry; conversion efficiency; product selectivity; and the mechanisms, pathways, and kinetics of the associated reactions). Current shortcomings and research avenues are also discussed to help establish a roadmap for future development of the gas-phase FF hydrogenation technology and associated disciplines. Overall, the present review is expected to offer much-needed insights into the scalability of metal-based catalytic systems for efficient FF hydrogenation in the gas phase.

Intermetallic Nanocrystals for Fuel-Cells-Based Electrocatalysis

Electrocatalysis underpins the renewable electrochemical conversions for sustainability, which further replies on metallic nanocrystals as vital electrocatalysts. Intermetallic nanocrystals have been known to show distinct properties compared to their disordered counterparts, and been long explored for functional improvements. Tremendous progresses have been made in the past few years, with notable trend of more precise engineering down to an atomic level and the investigation transferring into more practical membrane electrode assembly (MEA), which motivates this timely review. After addressing the basic thermodynamic and kinetic fundamentals, we discuss classic and latest synthetic strategies that enable not only the formation of intermetallic phase but also the rational control of other catalysis-determinant structural parameters, such as size and morphology. We also demonstrate the emerging intermetallic nanomaterials for potentially further advancement in energy electrocatalysis. Then, we discuss the state-of-the-art characterizations and representative intermetallic electrocatalysts with emphasis on oxygen reduction reaction evaluated in a MEA setup. We summarize this review by laying out existing challenges and offering perspective on future research directions toward practicing intermetallic electrocatalysts for energy conversions.

Strengthening Pt/WOx interfacial interactions to increase the CO tolerance of Pt for hydrogen oxidation reaction

Here, the modulation of the Pt electronic structure by the formation of an amorphous WOx overlayer on Pt nanoparticles is proposed. The resulting Pt/WOx@NC electrode shows exceptional CO oxidation potential (0.24 V vs. RHE) in aqueous test, and the corresponding membrane electrode assembly (MEA) steadily generates power in fuel cells fed with H2 gas containing 1000 ppm CO.

Recent Progress on Phase Engineering of Nanomaterials

As a key structural parameter, phase depicts the arrangement of atoms in materials. Normally, a nanomaterial exists in its thermodynamically stable crystal phase. With the development of nanotechnology, nanomaterials with unconventional crystal phases, which rarely exist in their bulk counterparts, or amorphous phase have been prepared using carefully controlled reaction conditions. Together these methods are beginning to enable phase engineering of nanomaterials (PEN), i.e., the synthesis of nanomaterials with unconventional phases and the transformation between different phases, to obtain desired properties and functions. This Review summarizes the research progress in the field of PEN. First, we present representative strategies for the direct synthesis of unconventional phases and modulation of phase transformation in diverse kinds of nanomaterials. We cover the synthesis of nanomaterials ranging from metal nanostructures such as Au, Ag, Cu, Pd, and Ru, and their alloys; metal oxides, borides, and carbides; to transition metal dichalcogenides (TMDs) and 2D layered materials. We review synthesis and growth methods ranging from wet-chemical reduction and seed-mediated epitaxial growth to chemical vapor deposition (CVD), high pressure phase transformation, and electron and ion-beam irradiation. After that, we summarize the significant influence of phase on the various properties of unconventional-phase nanomaterials. We also discuss the potential applications of the developed unconventional-phase nanomaterials in different areas including catalysis, electrochemical energy storage (batteries and supercapacitors), solar cells, optoelectronics, and sensing. Finally, we discuss existing challenges and future research directions in PEN.

Tailored Lattice Compressive Strain of Pt-Skins by the L12 -Pt3 M Intermetallic Core for Highly Efficient Oxygen Reduction

The sluggish kinetics of oxygen reduction reaction (ORR) and unsatisfactory durability of Pt-based catalysts are severely hindering the commercialization of proton-exchange-membrane fuel cells (PEMFCs). In this work, the lattice compressive strain of Pt-skins imposed by Pt-based intermetallic cores is tailored for highly effective ORR through the confinement effect of the activated nitrogen-doped porous carbon (a-NPC). The modulated pores of a-NPC not only promote Pt-based intermetallics with ultrasmall size (average size of <4 nm), but also efficiently stabilizes intermetallic nanoparticles and sufficient exposure of active sites during the ORR process. The optimized catalyst (L12 -Pt3 Co@ML-Pt/NPC10 ) achieves excellent mass activity (1.72 A mgPt -1 ) and specific activity (3.49 mA cmPt -2 ), which are 11- and 15-fold that of commercial Pt/C, respectively. Besides, owing to the confinement effect of a-NPC and protection of Pt-skins, L12 -Pt3 Co@ML-Pt/NPC10 retains 98.1% mass activity after 30 000 cycles, and even 95% for 100 000 cycles, while Pt/C retains only 51.2% for 30 000 cycles. Rationalized by density functional theory, compared with other metals (Cr, Mn, Fe, and Zn), L12 -Pt3 Co closer to the top of "volcano" induces a more suitable compressive strain and electronic structure on Pt-skin, leading to an optimal oxygen adsorption energy and a remarkable ORR performance.

Design of Pt-Sn-Zn Nanomaterials for Successful Methanol Electrooxidation Reaction

This work highlights the potential for the synthesis of new PtSnZn catalysts with enhanced efficiency and durability for methanol oxidation reaction (MOR) in low-temperature fuel cells. In this research, PtZn and PtSnZn nanoparticles deposited on high surface area Vulcan XC-72R Carbon support were created by a microwave-assisted polyol method. The electrochemical performances of synthesized catalysts were analyzed by cyclic voltammetry and by the electrooxidation of adsorbed CO and the chronoamperometric method. The physicochemical properties of obtained catalysts were characterized by transmission electron microscopy (TEM), thermogravimetric (TGA) analysis, energy dispersive spectroscopy (EDS) and by X-ray diffraction (XRD). The obtained findings showed the successful synthesis of platinum-based catalysts. It was established that PtSnZn/C and PtZn/C catalysts have high electrocatalytic performance in methanol oxidation reactions. Catalysts stability tests were obtained by chronoamperometry. Stability tests also confirmed decreased poisoning and indicated improved stability and better tolerance to CO-like intermediate species. According to activity and stability measurements, the PtSnZn/C catalyst possesses the best electrochemical properties for the methanol oxidation reaction. The observed great electrocatalytic activity in the methanol oxidation reaction of synthesized catalysts can be attributed to the beneficial effects of microwave synthesis and the well-balanced addition of alloying metals in PtSnZn/C catalysts.

Recent Advances on Transition-Metal-Based Layered Double Hydroxides Nanosheets for Electrocatalytic Energy Conversion

Transition-metal-based layered double hydroxides (TM-LDHs) nanosheets are promising electrocatalysts in the renewable electrochemical energy conversion system, which are regarded as alternatives to noble metal-based materials. In this review, recent advances on effective and facile strategies to rationally design TM-LDHs nanosheets as electrocatalysts, such as increasing the number of active sties, improving the utilization of active sites (atomic-scale catalysts), modulating the electron configurations, and controlling the lattice facets, are summarized and compared. Then, the utilization of these fabricated TM-LDHs nanosheets for oxygen evolution reaction, hydrogen evolution reaction, urea oxidation reaction, nitrogen reduction reaction, small molecule oxidations, and biomass derivatives upgrading is articulated through systematically discussing the corresponding fundamental design principles and reaction mechanism. Finally, the existing challenges in increasing the density of catalytically active sites and future prospects of TM-LDHs nanosheets-based electrocatalysts in each application are also commented.

Synthesis of Pt3Zn1 and Pt1Zn1 intermetallic nanocatalysts for dehydrogenation of ethane

Pt₃Zn₁ and Pt₁Zn₁ intermetallic nanoparticles supported on SiO₂ were synthesized by combining atomic layer deposition (ALD) of ZnO, incipient wetness impregnation (IWI) of Pt, and appropriate hydrogen reduction. The formation of Pt₁Zn₁ and Pt₃Zn₁ intermetallic nanoparticles was observed by both X-ray diffraction (XRD) and synchrotron X-ray absorption spectroscopy (XAS). STEM images showed that the 2-3 nm Pt-based intermetallic nanoparticles were uniformly dispersed on a SiO₂ support. The relationships between Pt-Zn intermetallic phases and synthesis conditions were established. In situ XAS measurements at Pt L₃ and Zn K edges during hydrogen reduction provided a detailed image of surface species evolution. Owing to a combined electronic and geometric effect, Pt₁Zn₁ exhibited much higher reactivity and stability than Pt₃Zn₁ and Pt in both the direct dehydrogenation and oxidative dehydrogenation of ethane to ethylene reactions.

Carbonized polydopamine layer-protected silicon substrates for light-addressable electrochemical sensing and imaging

The application of silicon (Si) substrate as photoelectrode in light-addressable electrochemistry (LAE) is severely limited due to its ease of surface oxidation. The resulted silicon oxide (SiO_x) layer is electronically insulating and blocks charge transfer between the electrode and electrolyte. Keeping the Si from being oxidized is a key challenge for its practical use as a semiconductor electrode. In this work, we find that by developing a thin layer of polydopamine film on the surface of Si substrate, followed by carbonization at 550 °C, the natural oxidation of Si substrate can be successfully forestalled. When applied as an electrode, it is further found that the carbonized polydopamine (cPDA) layer can also prevent anodic oxidation of Si. The cPDA layer-modified Si substrate exhibits good photoelectrochemical performance and great stability, with no obvious signal decrease under ambient environment over 32 h. Our work here provides a new modification strategy for anti-oxidation of Si substrate and it is promising in the application of light-addressable electrochemical sensing and imaging.

Platinum-Cobalt Nanowires for Efficient Alcohol Oxidation Electrocatalysis

The compositions and surface facets of platinum (Pt)-based electrocatalysts are of great significance for the development of direct alcohol fuel cells (DAFCs). We reported an approach for preparing ultrathin Pt_nCo_100-n nanowire (NW) catalysts with high activity. The Pt_nCo_100-n NW alloy catalysts synthesized by single-phase surfactant-free synthesis have adjustable compositions and (111) plane and strain lattices. X-ray diffraction (XRD) results indicate that the alloy composition can adjust the lattice shrinkage or expansion of Pt_nCo_100-n NWs. X-ray photoelectron spectroscopy (XPS) results show that the electron structure of Pt is changed by the alloying effect caused by electron modulation in the d band, and the chemical adsorption strength of Pt is decreased, thus the catalytic activity of Pt is increased. The experimental results show that the activity of Pt_nCo_100-n for the oxidation of methanol and ethanol is related to the exposed crystal surface, strain lattice and composition of catalysts. The Pt_nCo_100-n NWs exhibit stronger electrocatalytic performance for both methanol oxidation reaction (MOR) and ethanol oxidation reaction (EOR). The dominant (111) plane Pt₅₃Co₄₇ exhibits the highest electrocatalytic activity in MOR, which is supported by the results of XPS. This discovery provides a new pathway to design high activity, stability nanocatalysts to enhance direct alcohol fuel cells.

Phase diagrams guide synthesis of highly ordered intermetallic electrocatalysts: separating alloying and ordering stages

Supported platinum intermetallic compound catalysts have attracted considerable attention owing to their remarkable activities and durability for the oxygen reduction reaction in proton-exchange membrane fuel cells. However, the synthesis of highly ordered intermetallic compound catalysts remains a challenge owing to the limited understanding of their formation mechanism under high-temperature conditions. In this study, we perform in-situ high-temperature X-ray diffraction studies to investigate the structural evolution in the impregnation synthesis of carbon-supported intermetallic catalysts. We identify the phase-transition-temperature (TPT)-dependent evolution process that involve concurrent (for alloys with high TPT) or separate (for alloys with low TPT) alloying/ordering stages. Accordingly, we realize the synthesis of highly ordered intermetallic catalysts by adopting a separate annealing protocol with a high-temperature alloying stage and a low-temperature ordering stage, which display a high mass activity of 0.96 A mgPt-1 at 0.9 V in H2-O2 fuel cells and a remarkable durability.

PtCuRu Nanoflowers with Ru-Rich Edge for Efficient Fuel-Cell Electrocatalysis

Enhancing the catalytic activity of Pt-based alloy by a rational structural design is the key to addressing the sluggish kinetics of direct alcohol fuel cells. Herein, a facile one-pot method is reported to synthesize PtCuRu nanoflowers (NFs). The synergetic effect among Pt, Cu, and Ru can lower the d-band center of Pt, regulate the morphology, generate Ru-rich edge, and allow the exposure of more high index facets. The optimized Pt_0.68 Cu_0.18 Ru_0.14 NFs exhibit outstanding electrocatalytic performances and excellent anti-poisoning abilities. The specific activities for the methanol oxidation reaction (MOR) (7.65 mA cm^-2 ) and ethanol oxidation reaction (EOR) (7.90 mA cm^-2 ) are 6.0 and 7.1 times higher than commercial Pt/C, respectively. The CO stripping experiment and the chronoamperometric (5000 s) demonstrate the superior anti-poisoning property and durability performance. Density functional theory calculations confirm that high metallization degree leads to the decrease of d-band center, the promotion of oxidation of CO, and improvement of the inherent activity and anti-poisoning ability. A Ru-rich edge exposes abundant high index facets to accelerate the reaction kinetics of rate-determining steps by decreasing the energy barrier for forming *HCOOH (MOR) and CC bond breaking (EOR).

Isolating Contiguous Ir Atoms and Forming Ir-W Intermetallics with Negatively Charged Ir for Efficient NO Reduction by CO

The lack of efficient catalysts with a wide working temperature window and vital O₂ and SO₂ resistance for selective catalytic reduction of NO by CO (CO-SCR) largely hinders its implementation. Here, a novel Ir-based catalyst with only 1 wt% Ir loading is reported for efficient CO-SCR. In this catalyst, contiguous Ir atoms are isolated into single atoms, and Ir-W intermetallic nanoparticles are formed, which are supported on ordered mesoporous SiO₂ (KIT-6). Notably, this catalyst enables complete NO conversion to N₂ at 250 °C in the presence of 1% O₂ and has a wide temperature window (250-400 °C), outperforming the comparison samples with Ir isolated-single-atomic-sites and Ir nanoparticles, respectively. Also, it possesses a high SO₂ tolerance. Both experimental results and theoretical calculations reveal that single Ir atoms are negatively charged, dramatically enhancing the NO dissociation, while the Ir-W intermetallic nanoparticles accelerate the reduction of the N₂ O and NO₂ intermediates by CO.

Pd3Co1 Alloy Nanocluster on the MWCNT Catalyst for Efficient Formic Acid Electro-Oxidation

In this study, the Pd₃Co₁ alloy nanocluster from a multiwalled carbon nanotube (MWCTN) catalyst was fabricated in deep eutectic solvents (DESs) (referred to Pd₃Co₁/CNTs). The catalyst shows a better mass activity towards the formic acid oxidation reaction (FAOR) (2410.1 mA mg_Pd^-1), a better anti-CO toxicity (0.36 V) than Pd/CNTs and commercial Pd/C. The improved performance of Pd₃Co₁/CNTs is attributed to appropriate Co doping, which changed the electronic state around the Pd atom, lowered the d-band of Pd, formed a new Pd-Co bond act at the active sites, affected the adsorption of the toxic intermediates and weakened the dissolution of Pd; moreover, with the assistance of DES, the obtained ultrafine Pd₃Co₁ nanoalloy exposes more active sites to enhance the dehydrogenation process of the FAOR. The study shows a new way to construct a high-performance Pd-alloy catalyst for the direct formic acid fuel cell.

Intermetallic Nanoarchitectures for Efficient Electrocatalysis

Intermetallic structures whose regular atomic arrays of constituent elements present unique catalytic properties have attracted considerable attention as efficient electrocatalysts for energy conversion reactions. Further performance enhancement in intermetallic catalysts hinges on constructing catalytic surfaces possessing high activity, durability, and selectivity. In this Perspective, we introduce recent endeavors to boost the performance of intermetallic catalysts by generating nanoarchitectures, which have well-defined size, shape, and dimension. We discuss the beneficial effects of nanoarchitectures compared with simple nanoparticles in catalysis. We highlight that the nanoarchitectures have high intrinsic activity owing to their inherent structural factors, including controlled facets, surface defects, strained surfaces, nanoscale confinement effects, and a high density of active sites. We next present notable examples of intermetallic nanoarchitectures, namely, facet-controlled intermetallic nanocrystals and multidimensional nanomaterials. Finally, we suggest the future research directions of intermetallic nanoarchitectures.

Small molecule-assisted synthesis of carbon supported platinum intermetallic fuel cell catalysts

Supported ordered intermetallic compounds exhibit superior catalytic performance over their disordered alloy counterparts in diverse reactions. But the synthesis of intermetallic compounds catalysts often requires high-temperature annealing that leads to the sintering of metals into larger crystallites. Herein, we report a small molecule-assisted impregnation approach to realize the general synthesis of a family of intermetallic catalysts, consisting of 18 binary platinum intermetallic compounds supported on carbon blacks. The molecular additives containing heteroatoms (that is, O, N, or S) can be coordinated with platinum in impregnation and thermally converted into heteroatom-doped graphene layers in high-temperature annealing, which significantly suppress alloy sintering and insure the formation of small-sized intermetallic catalysts. The prepared optimal PtCo intermetallics as cathodic oxygen-reduction catalysts exhibit a high mass activity of 1.08 A mg_Pt^-1 at 0.9 V in H₂-O₂ fuel cells and a rated power density of 1.17 W cm^-2 in H₂-air fuel cells.

Cobalt Single Atoms Enabling Efficient Methanol Oxidation Reaction on Platinum Anchored on Nitrogen-Doped Carbon

Developing efficient platinum (Pt)-based electrocatalysts with high tolerance to CO poisoning for the methanol oxidation reaction is critical for the development of direct methanol fuel cells. In this work, cobalt single atoms are introduced to enhance the electrocatalytic performance of N-doped carbon supported Pt (N-C/Pt) for the methanol oxidation reaction. The cobalt single atoms are believed to play a critical role in accelerating the prompt oxidation of CO to CO₂ and minimizing the CO blocking of the adjacent Pt active sites. Benefitting from the synergistic effects among the Co single atoms, the Pt nanoparticles, and the N-doped carbon support, the Co-modified N-C/Pt (Co-N-C/Pt) electrocatalyst simultaneously delivers impressive electrocatalytic activity and durability with lower onset potential and superb CO poisoning resistance as compared to the N-C/Pt and the commercial Pt/C electrocatalysts.

High-Entropy Intermetallic PtRhBiSnSb Nanoplates for Highly Efficient Alcohol Oxidation Electrocatalysis

The control of multimetallic ensembles at the atomic-level is challenging, especially for high-entropy alloys (HEAs) possessing five or more elements. Herein, the one-pot synthesis of hexagonal-close-packed (hcp) PtRhBiSnSb high-entropy intermetallic (HEI) nanoplates with intrinsically isolated Pt, Rh, Bi, Sn, and Sb atoms is reported, to boost the electrochemical oxidation of liquid fuels. Taking advantage of these combined five metals, the well-defined PtRhBiSnSb HEI nanoplates exhibit a remarkable mass activity of 19.529, 15.558, and 7.535 A mg^-1 _Pt+Rh toward the electrooxidation of methanol, ethanol, and glycerol in alkaline electrolytes, respectively, representing a state-of-the-art multifunctional electrocatalyst for alcohol oxidation reactions. In particular, the PtRhBiSnSb HEI achieves record-high methanol oxidation reaction (MOR) activity in an alkaline environment. Theoretical calculations demonstrate that the introduction of the fifth metal Rh enhances the electron-transfer efficiency in PtRhBiSnSb HEI nanoplates, which contributes to the improved oxidation capability. Meanwhile, robust electronic structures of the active sites are achieved due to the synergistic protections from Bi, Sn, and Sb sites. This work offers significant research advances in developing well-defined HEA with delicate control over compositions and properties.

Controlling C-C coupling in electrocatalytic reduction of CO2 over Cu1-xZnx/C

From the perspective of sustainable environment and economic value, the electroreduction of CO₂ to higher order multicarbon products is more coveted than that of C₁ products, owing to their higher energy densities and a wider applicability. However, the reduction process remains extremely challenging due to the bottleneck of C-C coupling over the catalyst surfaces, and therefore designing a suitable catalyst for efficient and selective electrocatalytic reduction of CO₂ is a need of the hour. With the target of producing C₃₊ products with higher selectivity, in this study we explored the nano-alloys of Cu_1-xZn_x as electrocatalysts for CO₂ reduction. The nano-alloy Cu_1-xZn_x synthesized from the corresponding bimetallic metal organic framework materials demonstrated a gradual enhancement in the selectivity of acetone upon CO₂ electroreduction with higher doping of Zn. The Cu_1-xZn_x alloy opened up a wide possibility of fine-tuning the electronic structure by shifting the position of the d-band centre and modulating the interaction with intermediate CO and thus enhanced the selectivity of desirable products, which might not have been accessible otherwise. The postulated molecular mechanism of CO₂ electroreduction involving the desorption of the poorly adsorbed intermediate CO due to the presence of Zn and spilling over of free CO to Cu sites in the nano-alloy Cu_1-xZn_x for further C-C coupling to yield acetone was corroborated by the first principles studies.

Enhanced Activity of Oxygen Reduction Reaction on Pr6O11-Assisted PtPr Alloy Electrocatalysts

Pt-based alloy catalysts for oxygen reduction reaction (ORR) with outstanding performance have been well-studied in recent years. Among these, Pt-lanthanide alloy catalysts have been developed with quite a competitive ORR activity. However, to promote practical applications of a proton-exchange membrane fuel cell (PEMFC), catalysts with superior activity are still being explored. Herein, we present the Pr₆O₁₁-assisted Pt-Pr catalyst exhibiting further improved ORR activity than the state-of-the-art Pt/C. A simple annealing treatment is applied after the synthesis of the Pt-Pr alloy, obtaining Pr₆O₁₁ nanoparticles attached to the surface of the Pt-Pr alloy to form a Pt-Pr/Pr₆O₁₁ composite catalyst. Experimental and theoretical studies reveal that the electronic state of Pt in the Pt-Pr/Pr₆O₁₁ system is modified. It was found that the strong oxophilicity of Pr adjusts the active site of Pt and promotes the adsorption and dissociation of O₂. The preeminent intrinsic ORR activity on the Pt-Pr/Pr₆O₁₁ catalyst reaches the promoted specific activity (2.01 mA cm^-2) and mass activity (1.3 A mg_Pt^-1), which were 5.91- and 5.90-fold higher than those obtained by the state-of-the-art Pt/C catalyst (0.34 mA cm^-2 and 0.22 A mg_Pt^-1). This study provides us with an idea that the ORR performance of Pt-based alloy could be enhanced with the assistance of the metal oxide phase.

Ordered Intermetallic PtCu Catalysts Made from Pt@Cu Core/Shell Structures for Oxygen Reduction Reaction

Platinum-based ordered intermetallic compounds are promising low-Pt catalysts toward the oxygen reduction reaction (ORR) for high-performance fuel cells. However, the synthesis of ordered intermetallic catalysts usually requires high-temperature annealing to overcome the energy barrier for atom diffusion, which leads to inevitable sintering of catalysts and greatly reduced mass-specific activity. Herein, we developed a new strategy to synthesize PtCu-ordered intermetallic catalysts by the generation of the Pt@Cu core/shell nanoparticles (Pt@Cu NPs) by Pt-assisted H₂ reduction of Cu²⁺ with subsequent annealing at 500-1000 °C. Compared to the commonly used wet-impregnation method, the core/shell structure starts to form ordered PtCu alloys at a lower annealing temperature (500 °C). The Pt@Cu core/shell structure avoids the necessary process of Cu atoms diffusing to Pt NPs across the carbon supports occurred during high-temperature annealing in the wet-impregnation method, which ensures the formation of PtCu NPs with higher ordering degree while annealing at the same temperature. The highly ordered small-sized PtCu catalysts prepared by the core/shell strategy exhibit higher mass activity and specific activity compared to those prepared by the wet-impregnation method. Moreover, a positive correlation between the ORR activity and the ordering degree of the intermetallic PtCu NPs is identified, which could be associated with the increase of compressive strain with the ordering degree.

Boosting Thermal Stability of Volatile Os Catalysts by Downsizing to Atomically Dispersed Species

Os-based catalysts present remarkable catalytic activity; however, their use has been limited by the undesirable side reactions that generate highly toxic and volatile OsO₄ even at room temperature. Herein, we demonstrate that the thermal stability of Os-based catalysts can be dramatically improved by downsizing Os nanoparticles (NPs) into atomically dispersed species. We observed that Os NPs were converted into OsO₄ after calcination at 250 °C followed by sublimation, whereas single Os sites retained their structure after calcination. Temperature-programmed oxidation analysis confirmed that Os NPs started to undergo oxidation at 130 °C, whereas atomically dispersed Os preserved its state up to 300 °C. The CO oxidation activity of the atomically dispersed Os catalyst at 400 °C (100% conversion) was stably preserved over 30 h. By contrast, the activity of Os NP catalyst declined drastically. This study highlights the unique catalytic behavior of atomically dispersed catalysts, which is distinct from that of NP-based catalysts.

Toward a Comprehensive Understanding of Cation Effects in Proton Exchange Membrane Fuel Cells

Metal alloy catalysts (e.g., Pt-Co) are widely used in fuel cells for improving the oxygen reduction reaction kinetics. Despite the promise, the leaching of the alloying element contaminates the ionomer/membrane, leading to poor durability. However, the underlying mechanisms by which cation contamination affects fuel cell performance remain poorly understood. Here, we provide a comprehensive understanding of cation contamination effects through the controlled doping of electrodes. We couple electrochemical testing results with membrane conductivity/water uptake measurements and impedance modeling to pinpoint where and how the losses in performance occur. We identify that (1) ∼44% of Co²⁺ exchange of the ionomer can be tolerated in the electrode, (2) loss in performance is predominantly induced by O₂ and proton transport losses, and (3) Co²⁺ preferentially resides in the electrode under wet operating conditions. Our results provide a first-of-its-kind mechanistic explanation for cation effects and inform strategies for mitigating these undesired effects when using alloy catalysts.

Single-ion chelation strategy for synthesis of monodisperse Pd nanoparticles anchored in MOF-808 for highly efficient hydrogenation and cascade reactions

Ultrafine Pd nanoparticles are prepared using a single-ion precursor on a MOF-808 carrier. The ligand 2,3-pyrazinedicarboxylic acid (Pza) is dispersed in porous MOF-808 via grafting on formic acid sites, and thus Pd²⁺ ions are chelated by Pza to form a new single-ion precursor Pd@MOF-808-Pza. Then a Pd-nano@MOF-808-Pza catalyst is prepared by direct reduction of this precursor using NaBH₄. Material characterization reveals the homogeneous dispersion of 3-6 nm Pd nanoparticles within the MOF-808 matrix. Pd-nano@MOF-808-Pza exhibits excellent catalytic activity in the hydrogenation of unsaturated nitrogen-containing compounds, and other typical reactions, such as the Knoevenagel condensation, Suzuki/Heck cross-coupling, and hydrogen tandem reactions. In addition, density functional theory (DFT) calculations are carried out to elucidate the chelation of Pd²⁺ ions by Pza on MOF-808 and propose mechanisms of hydrogenation reactions. This work provides an effective reduction catalyst, and more importantly, a single-ion chelation strategy for design and synthesis of metal supported catalysts.

Solid-State Reaction Synthesis of Nanoscale Materials: Strategies and Applications

Nanomaterials (NMs) with unique structures and compositions can give rise to exotic physicochemical properties and applications. Despite the advancement in solution-based methods, scalable access to a wide range of crystal phases and intricate compositions is still challenging. Solid-state reaction (SSR) syntheses have high potential owing to their flexibility toward multielemental phases under feasibly high temperatures and solvent-free conditions as well as their scalability and simplicity. Controlling the nanoscale features through SSRs demands a strategic nanospace-confinement approach due to the risk of heat-induced reshaping and sintering. Here, we describe advanced SSR strategies for NM synthesis, focusing on mechanistic insights, novel nanoscale phenomena, and underlying principles using a series of examples under different categories. After introducing the history of classical SSRs, key theories, and definitions central to the topic, we categorize various modern SSR strategies based on the surrounding solid-state media used for nanostructure growth, conversion, and migration under nanospace or dimensional confinement. This comprehensive review will advance the quest for new materials design, synthesis, and applications.

A General Concurrent Template Strategy for Ordered Mesoporous Intermetallic Nanoparticles with Controllable Catalytic Performance

We report a general concurrent template strategy for precise synthesis of mesoporous Pt-/Pd-based intermetallic nanoparticles with desired morphology and ordered mesostructure. The concurrent template not only supplies a mesoporous metal seed for re-crystallization growth of atomically ordered intermetallic phases with unique atomic stoichiometry but also provides a nanoconfinement environment for nanocasting synthesis of mesoporous nanoparticles with ordered mesostructure and rhombic dodecahedral morphology under elevated temperature. Using the selective hydrogenation of 3-nitrophenylacetylene as a proof-of-concept catalytic reaction, mesoporous intermetallic PtSn nanoparticles exhibited remarkably controllable intermetallic phase-dependent catalytic selectivity and excellent catalytic stability. This work provides a very powerful strategy for precise preparation of ordered mesoporous intermetallic nanocrystals for application in selective catalysis and fuel cell electrocatalysis.

Noble Metal-Based Multimetallic Nanoparticles for Electrocatalytic Applications

Noble metal-based multimetallic nanoparticles (NMMNs) have attracted great attention for their multifunctional and synergistic effects, which offer numerous catalytic applications. Combined experimental and theoretical studies have enabled formulation of various design principles for tuning the electrocatalytic performance through controlling size, composition, morphology, and crystal structure of the nanoparticles. Despite significant advancements in the field, the chemical synthesis of NMMNs with ideal characteristics for catalysis, including high activity, stability, product-selectivity, and scalability is still challenging. This review provides an overview on structure-based classification and the general synthesis of NMMN electrocatalysts. Furthermore, postsynthetic treatments, such as the removal of surfactants to optimize the activity, and utilization of NMMNs onto suitable support for practical electrocatalytic applications are highlighted. In the end, future direction and challenges associated with the electrocatalysis of NMMNs are covered.