General Method of Manipulating Formation, Composition, and Morphology of Solid-Electrolyte Interphases for Stable Li-Alloy Anodes

Enhancing lithium storage performance with silicon-based anodes: a theoretical study on transition metal-integrated SiOx/M@C (M = Fe, Co, Ni) heterostructures

In lithium-ion batteries, infusible metals with lithium, such as Mg, Fe, Co, Ni, and Cu are often utilized. However, current research predominantly focuses on the experimental aspects of the (de)lithiation process, with limited exploration from a theoretical calculation perspective. The extensive use of experimental methods to study the many electrochemically inert metals is time-consuming and costly. In this study, we successfully constructed and optimized SiOx/M@C (M = Fe, Co, Ni) heterostructures, integrating transition metal nanoparticles to address the electrochemical inertness and slow diffusion kinetics of pristine SiOx. A comprehensive density functional theory (DFT) study was conducted to examine the effects of different metal heterostructures on the structural, migration potential energy, and adsorption properties during lithium-ion intercalation. The results demonstrate that the SiOx/Fe@C heterostructure exhibits the lowest migration energy barrier, significantly enhancing lithium-ion transport compared to SiOx/Co@C and SiOx/Ni@C. Consequently, the SiOx/Fe@C electrode shows superior high-rate discharge capability and excellent cycling performance through electrochemical measurements. Additionally, the study delves into the intrinsic mechanisms through charge density differences and Fermi level calculations, providing valuable insights into the importance of hybrid strategies for incorporating inert metals into anode materials for lithium-ion batteries.

Scanning Electrochemical Microscopy Reveals That Model Silicon Anodes Demonstrate Global Solid Electrolyte Interphase Passivation Degradation during Calendar Aging

Silicon is a promising next-generation anode to increase energy density over commercial graphite anodes, but calendar life remains problematic. In this work, scanning electrochemical microscopy was used to track the site-specific reactivity of a silicon thin film surface over time to determine if undesirable Faradaic reactions were occurring at the formed solid electrolyte interphase (SEI) during calendar aging in four case scenarios: formation between 1.5 V and 100 mV with subsequent rest starting at (1) 1.5 V and (2) 100 mV and formation between 0.75 V and 100 mV with subsequent rest starting at (3) 0.75 V and (4) 100 mV. In all cases, the electrical passivation of silicon decreased with increasing time and potential relative to Li/Li+ over a 3 day period. Along with the decrease in passivation, the homogeneity of passivation over a 500 μm2 area decreased with time. Despite some local "hot spots" of reactivity, the areal uniformity of passivation suggests global SEI failure (e.g., SEI dissolution) rather than localized (e.g., cracking) failure. The silicon delithiated to 1.5 V vs Li/Li+ was less passivated than the lithiated silicon (at the beginning of rest, the forward rate constants, kf, for ferrocene redox were 7.19 × 10-5 and 3.17 × 10-7 m/s, respectively) and was also found to be more reactive than the pristine silicon surface (kf of 5 × 10-5 m/s). This reactivity was likely the result of SEI oxidation. When the cell was only delithiated up to 0.75 V versus Li/Li+, the surface was still passivating (kf of 6.11 × 10-6 m/s), but still less so than the lithiated surface (kf of 3.03 × 10-9 m/s). This indicates that the potential of the anode should be kept at or below ∼0.75 V vs Li/Li+ to prevent decreasing SEI passivation. This information will help with tuning the voltage windows for prelithiation in Si half cells and the operating voltage of Si full cells to optimize calendar life. The results provided should encourage the research community to investigate chemical, rather than mechanical, modes of failure during calendar aging and to stop using the typical convention of 1.5 V as a cutoff potential for cycling Si in half cells.

Click Chemistry in Lithium-Metal Batteries

Lithium-metal batteries (LMBs) are considered the "holy grail" of the next-generation energy storage systems, and solid-state electrolytes (SSEs) are a kind of critical component assembled in LMBs. However, as one of the most important branches of SSEs, polymer-based electrolytes (PEs) possess several native drawbacks including insufficient ionic conductivity and so on. Click chemistry is a simple, efficient, regioselective, and stereoselective synthesis method, which can be used not only for preparing PEs with outstanding physical and chemical performances, but also for optimizing the stability of solid electrolyte interphase (SEI) layer and elevate the cycling properties of LMBs effectively. Here it is primarily focused on evaluating the merits of click chemistry, summarizing its existing challenges and outlining its increasing role for the designing and fabrication of advanced PEs. The fundamental requirements for reconstructing artificial SEI layer through click chemistry are also summarized, with the aim to offer a thorough comprehension and provide a strategic guidance for exploring the potentials of click chemistry in the field of LMBs.

Stabilizing Lithium-Metal Host Anodes by Covalently Binding MgF2 Nanodots to Honeycomb Carbon Nanofibers

Constructing lithiophilic carbon hosts has been regarded as an effective strategy for inhibiting Li dendrite formation and mitigating the volume expansion of Li metal anodes. However, the limitation of lithiophilic carbon hosts by conventional surface decoration methods over long-term cycling hinders their practical application. In this work, a robust host composed of ultrafine MgF2 nanodots covalently bonded to honeycomb carbon nanofibers (MgF2/HCNFs) is created through an in situ solid-state reaction. The composite exhibits ultralight weight, excellent lithiophilicity, and structural stability, contributing to a significantly enhanced energy efficiency and lifespan of the battery. Specifically, the strong covalent bond not only prevents MgF2 nanodots from migrating and aggregating but also enhances the binding energy between Mg and Li during the molten Li infusion process. This allows for the effective and stable regulation of repeated Li plating/stripping. As a result, the MgF2/HCNF-Li electrode delivers a high Coulombic efficiency of 97% after 200 cycles, cycling stably for more than 2000 h. Furthermore, the full cells with a LiFePO4 cathode achieve a capacity retention of 85% after 500 cycles at 0.5C. This work provides a strategy to guide dendrite-free Li deposition patterns toward the development of high-performance Li metal batteries.

Robust bond linkage between boron-based coating layer and lithium polyacrylic acid binder enables ultra-stable micro-sized germanium anodes

Micro-sized alloy type germanium (Ge) anodes possess appealing properties for next-generation lithium ions batteries, such as desirable capacity, easy accessibility and greater tapdensity. Nevertheless, volume expansion accompanied by severe pulverization and continuous growth of solid electrolyte interlayer (SEI) still represent fundamental obstacles to their practical applications. Herein, we propose a fresh strategy of constructing robust bond linkage between boron-based coating layer and lithiated polyacrylic acid (PAALi) binder to circumvent the pulverization problems of Ge anodes. Facile pyrolysis of boric acid can introduce an amorphous boron oxide interphase on Ge microparticles (noted as Ge@B2O3). Then in situ crosslinking reaction between B2O3 and PAALi via BOC bond linkage constructs a robust Ge anode (Ge@B-PAALi), which is proved by FTIR and Raman characterizations. Post morphological and compositional investigations reveal the minimized pulverization and a thinner SEI composition. The robust bond linkage strategy endows Ge anode with ultra-stable cycling properties of 1053.8 mAh/g after 500 cycles at 1 A/g vs. 500.7 mAh/g for Ge@PAALi and 372.7 mAh/g for Ge@B2O3, respectively. The proposed bond linkage strategy via artificial coating layer and functional binders unlocks huge potential of alloys and other anodes for next-generation battery applications.

Surface ChemistryControlled SEI Layer on Silicon Electrodes by Regulating Electrolyte Decomposition

Unstable solid electrolyte interface (SEI) layers induced by significant volume changes and subsequent side reactions at the interface have prevented Si anodes from practical application in lithium-ion batteries. The interface stability plays an important role in the electrochemical performance of Si electrodes. Here, we modify the interface of a Si electrode with ion-conductive poly(ethylene glycol) diglycidyl ether (PEGDE), which controls the electrolyte decomposition route and stabilizes the SEI layer. It enables the Si electrode to achieve a capacity of more than 1800 mAh g^-1 at a current density of 2 A g^-1, with a capacity retention of 77.25% after 300 cycles. The PEGDE-decorated Si electrode also shows greatly improved rate capability, with specific capacity up to 777 mAh g^-1 even at 20 A g^-1. We demonstrate that PEGDE decoration greatly increases the Li₂CO₃ ratio in the SEI layer, which improves the interface stability and Li⁺ conductivity and hence suppresses continuous electrolyte decomposition. As a result, the structural integrity of the Si particles is maintained and capacity fading is retarded. This work reveals that surface design can effectively regulate the SEI layer composition and improve interface stability, which is a promising strategy for Si-electrode manufacture.

Pt-Coated Silicon Nanoparticles: An Investigation into the Hydrosilylation on Hydrogen-Terminated Silicon Surfaces Using Pt(dvs)

The interaction of hydrogen-terminated silicon nanoparticles (H-SiNPs) with Karstedt's catalyst at various temperatures was investigated. The results indicate that at room temperature, the oxidative addition of Pt(0) onto H-SiNPs is irreversible, and the catalyst is not eliminated from the surface of H-SiNPs, enabling a facile synthesis of Pt-loaded SiNPs that can undergo ligand exchange. The nature of the Pt-on-Si ensemble is characterized by Fourier transform infrared spectroscopy, X-ray photoelectron spectroscopy, transmission electron microscopy, and energy-dispersive X-ray spectroscopy. Reaction conditions that enable effective hydrosilylation are discussed. It is found that higher temperatures favor reductive elimination of the catalyst and hydrosilylation of 1-octene onto the surface of the H-SiNPs.

Progressive and instantaneous nature of lithium nucleation discovered by dynamic and operando imaging

The understanding of lithium (Li) nucleation and growth is important to design better electrodes for high-performance batteries. However, the study of Li nucleation process is still limited because of the lack of imaging tools that can provide information of the entire dynamic process. We developed and used an operando reflection interference microscope (RIM) that enables real-time imaging and tracking the Li nucleation dynamics at a single nanoparticle level. This dynamic and operando imaging platform provides us with critical capabilities to continuously monitor and study the Li nucleation process. We find that the formation of initial Li nuclei is not at the exact same time point, and Li nucleation process shows the properties of both progressive and instantaneous nucleation. In addition, the RIM allows us to track the individual Li nucleus's growth and extract spatially resolved overpotential map. The nonuniform overpotential map indicates that the localized electrochemical environments substantially influence the Li nucleation.

Metal-Metal Bonding as an Electrode Design Principle in the Low-Strain Cluster Compound LiScMo3O8

Electrode materials for Li⁺-ion batteries require optimization along several disparate axes related to cost, performance, and sustainability. One of the important performance axes is the ability to retain structural integrity though cycles of charge/discharge. Metal-metal bonding is a distinct feature of some refractory metal oxides that has been largely underutilized in electrochemical energy storage, but that could potentially impact structural integrity. Here LiScMo₃O₈, a compound containing triangular clusters of metal-metal bonded Mo atoms, is studied as a potential anode material in Li⁺-ion batteries. Electrons inserted though lithiation are localized across rigid Mo₃ triangles (rather than on individual metal ions), resulting in minimal structural change as suggested by operando diffraction. The unusual chemical bonding allows this compound to be cycled with Mo atoms below a formally +4 valence state, resulting in an acceptable voltage regime that is appropriate for an anode material. Several characterization methods including potentiometric entropy measurements indicate two-phase regions, which are attributed through extensive first-principles modeling to Li⁺ ordering. This study of LiScMo₃O₈ provides valuable insights for design principles for structural motifs that stably and reversibly permit Li⁺ (de)insertion.

A Review on Recent Advances for Boosting Initial Coulombic Efficiency of Silicon Anodic Lithium Ion batteries

Rechargeable silicon anode lithium ion batteries (SLIBs) have attracted tremendous attention because of their merits, including a high theoretical capacity, low working potential, and abundant natural sources. The past decade has witnessed significant developments in terms of extending the lifespan and maintaining high capacities of SLIBs. However, the detrimental issue of low initial Coulombic efficiency (ICE) toward SLIBs is causing more and more attention in recent years because ICE value is a core index in full battery design that profoundly determines the utilization of active materials and the weight of an assembled battery. Herein, a comprehensive review is presented of recent advances in solutions for improving ICE of SLIBs. From design perspectives, the strategies for boosting ICE of silicon anodes are systematically categorized into several aspects covering structure regulation, prelithiation, interfacial design, binder design, and electrolyte additives. The merits and challenges of various approaches are highlighted and discussed in detail, which provides valuable insights into the rational design and development of state-of-the-art techniques to deal with the deteriorative issue of low ICE of SLIBs. Furthermore, conclusions and future promising research prospects for lifting ICE of SLIBs are proposed at the end of the review.

Progress in Solid Polymer Electrolytes for Lithium-Ion Batteries and Beyond

Solid-state polymer electrolytes (SPEs) for high electrochemical performance lithium-ion batteries have received considerable attention due to their unique characteristics; they are not prone to leakage, and they exhibit low flammability, excellent processability, good flexibility, high safety levels, and superior thermal stability. However, current SPEs are far from commercialization, mainly due to the low ionic conductivity, low Li⁺ transference number (t_Li+ ), poor electrode/electrolyte interface contact, narrow electrochemical oxidation window, and poor long-term stability of Li metal. Recent work on improving electrochemical performance and these aspects of SPEs are summarized systematically here with a particular focus on the underlying mechanisms, and the improvement strategies are also proposed. This review could lead to a deeper consideration of the issues and solutions affecting the application of SPEs and pave a new pathway to safe, high-performance lithium-ion batteries.

In Situ Formed Lithiophilic LixNbyO in a Carbon Nanofiber Network for Dendrite-Free Li-Metal Anodes

Lithium metal is considered as a strongly attractive anode candidate for the high-energy-storage field, but its dreadful dendrite growth has haunted its commercialization progress. Herein, we develop a lithiophilic Nb₂O₅-embedded three-dimensional (3D) carbon nanofiber network (Nb₂O₅-CNF) as a scaffold to preload molten Li for the fabrication of dendrite-free composite anode. The in situ lithiation reaction between molten Li and Nb₂O₅ nanocrystals results in the formation of nanosize Li_xNb_yO nanoparticles, which can serve as preferred sites that regulate nucleation/growth behavior of Li during the plating process. Besides, due to its high structural stability and abundant internal inner space, the 3D CNF network can function as a reservoir to confine the dimensional expansion of "hostless Li". The resulting Li composite anodes exhibit enlarged active areas and reduced interfacial energy barriers, delivering a prolonged cycling of 1000 h with an ultralow hysteresis of 52 mV and dendrite-free morphology in a symmetric cell (1.0 mA cm^-2). Coupled with the LiFePO₄ cathode, the Li@Nb₂O₅-CNF anode sustains a reversible capacity of 163 mAh g^-1 with an excellent capacity retention of 93.0% after 370 cycles at 0.5C. This all-around strategy of lithiophilic sites coupled with a 3D conductive nanofiber matrix may shed light on promising applications of high-capacity and dendrite-free Li-metal batteries.

Constructing Robust Cross-Linked Binder Networks for Silicon Anodes with Improved Lithium Storage Performance

Despite the high specific capacity of silicon as a promising anode material for the next-generation high-capacity Li-ion batteries (LIBs), its practical applications are impeded by the rapid capacity decay during cycling. To tackle the issue, herein, a binder-grafting strategy is proposed to construct a covalently cross-linked binder [carboxymethyl cellulose/phytic acid (CMC/PA)], which builds a robust branched network with more contact points, allowing stronger bonds with Si nanoparticles by hydrogen bonding. Benefitting from the enhanced mechanical reliability, the resulting Si-CMC/PA electrodes exhibit a high reversible capacity with improved long-term cycling stability. Moreover, an assembled full cell consisting of the as-obtained Si-CMC/PA anode and commercial LiFePO₄ cathode also exhibits excellent cycling performance (120.4 mA h g^-1 at 1 C for over 100 cycles with 88.4% capacity retention). In situ transmission electron microscopy was employed to visualize the binding effect of CMC/PA, which, unlike the conventional CMC binder, can effectively prevent the lithiated Si anodes from cracking. Furthermore, the combined ex situ microscopy and X-ray photoelectron spectroscopy analysis unveils the origin of the superior Li-ion storage performance of the Si-CMC/PA electrode, which arises from its excellent structural integrity and the stabilized solid-electrolyte interphase films during cycling. This work presents a facile and efficient binder-engineering strategy for significantly improving the performance of Si anodes for next-generation LIBs.

Stable Rooted Solid Electrolyte Interphase for Lithium-Ion Batteries

Metal oxide-based materials are attractive anode candidates for lithium-ion batteries (LIBs) because of their high theoretical capacity. However, these materials suffer from large volume expansion and poor stability of solid electrolyte interphase (SEI) during the charge-discharge process, casusing rapid capacity degradation. Herein, we report that Li₃PO₄-rooted and intact SEI in situ formed on the phosphate-modified SnO₂/CNFs during cycling. The phosphate anions in the anode, could serve as the root to form Li₃PO₄ by bonding with Li ions and participate in the formation of the SEI, thus firmly anchoring and stabilizing the SEI layer. The rooted Li₃PO₄ and enriched LiF in the SEI could synergistically enhance the Li-ion diffusion, significantly reduce the volume expansion, and lead to ultrastable cycling performance over 1100 charge-discharge cycles at 1 A g^-1. This work provides a new avenue for forming stable SEI rooted into the anode and inspires the development of interface engineering toward electrochemical energy storage.

Microscale Silicon-Based Anodes: Fundamental Understanding and Industrial Prospects for Practical High-Energy Lithium-Ion Batteries

To accelerate the commercial implementation of high-energy batteries, recent research thrusts have turned to the practicality of Si-based electrodes. Although numerous nanostructured Si-based materials with exceptional performance have been reported in the past 20 years, the practical development of high-energy Si-based batteries has been beset by the bias between industrial application with gravimetrical energy shortages and scientific research with volumetric limits. In this context, the microscale design of Si-based anodes with densified microstructure has been deemed as an impactful solution to tackle these critical issues. However, their large-scale application is plagued by inadequate cycling stability. In this review, we present the challenges in Si-based materials design and draw a realistic picture regarding practical electrode engineering. Critical appraisals of recent advances in microscale design of stable Si-based materials are presented, including interfacial tailoring of Si microscale electrode, surface modification of SiO_x microscale electrode, and structural engineering of hierarchical microscale electrode. Thereafter, other practical metrics beyond active material are also explored, such as robust binder design, electrolyte exploration, prelithiation technology, and thick-electrode engineering. Finally, we provide a roadmap starting with material design and ending with the remaining challenges and integrated improvement strategies toward Si-based full cells.

Constructing a Reinforced and Gradient Solid Electrolyte Interphase on Si Nanoparticles by In-Situ Thiol-Ene Click Reaction for Long Cycling Lithium-Ion Batteries

Constructing a stable solid electrolyte interphase (SEI) on high-specific-capacity silicon (Si) anode is one of the most effective methods to reduce the crack of SEI and improve the cycling performance of Si anode. Herein, the authors construct a reinforced and gradient SEI on Si nanoparticles by an in-situ thiol-ene click reaction. Mercaptopropyl trimethoxysilane (MPTMS) with thiol functional groups (SH) is first grafted on the Si nanoparticles through condensation reaction, which then in-situ covalently bonds with vinylene carbonate (VC) to form a reinforced and uniform SEI on Si nanoparticles. The modified SEI with sufficient elastic Li_x SiO_y can homogenize the stress and strain during the lithiation of Si nanoparticles to reduce their expansion and prevent the SEI from cracking. The Si nanoparticles-graphite blending anode with the reinforced SEI exhibits excellent performance with an initial coulombic efficiency of ≈90%, a capacity of 1053.3 mA h g^-1 after 500 cycles and a high capacity of 852.8 mA h g^-1 even at a high current density of 3 A g^-1 . Moreover, the obtained anode shows superior cycling stability under both high loadings and lean electrolyte. The in-situ thiol-ene click reaction is a practical method to construct reinforced SEI on Si nanoparticles for next-generation high-energy-density lithium-ion batteries.

Mechanical studies of the solid electrolyte interphase on anodes in lithium and lithium ion batteries

A stable solid electrolyte interphase (SEI) layer is key to high performing lithium ion and lithium metal batteries for metrics such as calendar and cycle life. The SEI must be mechanically robust to withstand large volumetric changes in anode materials such as lithium and silicon, so understanding the mechanical properties and behavior of the SEI is essential for the rational design of artificial SEI and anode form factors. The mechanical properties and mechanical failure of the SEI are challenging to study, because the SEI is thin at only ~10-200 nm thick and is air sensitive. Furthermore, the SEI changes as a function of electrode material, electrolyte and additives, temperature, potential, and formation protocols. A variety ofin situandex situtechniques have been used to study the mechanics of the SEI on a variety of lithium ion battery anode candidates; however, there has not been a succinct review of the findings thus far. Because of the difficulty of isolating the true SEI and its mechanical properties, there have been a limited number of studies that can fully de-convolute the SEI from the anode it forms on. A review of past research will be helpful for culminating current knowledge and helping to inspire new innovations to better quantify and understand the mechanical behavior of the SEI. This review will summarize the different experimental and theoretical techniques used to study the mechanics of SEI on common lithium battery anodes and their strengths and weaknesses.

Development of oxidized hydroxyethyl cellulose-based hydrogel enabling unique mechanical, transparent and photochromic properties for contact lenses

With the development of smart devices, higher requirements are put forward for the stimuli-responsive materials. Stimuli-hydrogels as one kind of stimuli-responsive materials with hydrophilicity, demonstrate huge potential in developing intelligent devices for biomedical application. On this basis, we herein report that a sample method was devised to develop a novel composite hydrogel mainly based on oxidized hydroxyethyl cellulose and allyl co-polymer. Subsequently, a series of tests toward this oxidized hydroxyethyl cellulose-based hydrogel due to its structure and performance was applied. Here, the oxidized hydroxyethyl cellulose molecular chains were used as biomacromolecule templates to form Schiff base, borate and hydrogen bonds to obtain unique mechanical properties (fast recovery with almost no-hysteresis and remarkable compressive capacity), while a double bond functionalized spirooxazine (allyl spirooxazine derivative) was applied to endow photo- and pH sensitivity to the oxidized hydroxyethyl cellulose-based transparent hydrogel (T% = 93%) substrate. Furthermore, the oxidized hydroxyethyl cellulose-based hydrogel did exhibit good pH environment adaptability and noncytotoxicity in vitro test. Based on the advanced characteristics, the designed oxidized hydroxyethyl cellulose-based hydrogel has potential applications prospect in the development of safe, fashionable and pH- detectable contact lenses, thereby providing a new strategy for the development of smart, stylish contact lenses.

In Situ Developed Si@Polymethyl Methacrylate Capsule as a Li-Ion Battery Anode with High-Rate and Long Cycle-Life

The development of Si-based lithium-ion batteries is restricted by the large volume expansion of Si materials and the unstable solid electrolyte interface film. Herein, a novel Si capsule with in situ developed polymethyl methacrylate (PMMA) shell is prepared via microemulsion polymerization, in which PMMA has high lithium conductivity, high elasticity, certain viscosity in electrolytes, as well as good electrolyte retention ability. Taking advantage of the microcapsule structure with the PMMA capsid, the novel Si capsule anode retains 1.2 mA h/cm² at a current density of 2 A/g after 200 electrochemical cycles and delivers higher than 66% of its initial capacity at 42 A/g.

Atomic/molecular layer deposition for energy storage and conversion

Energy storage and conversion systems, including batteries, supercapacitors, fuel cells, solar cells, and photoelectrochemical water splitting, have played vital roles in the reduction of fossil fuel usage, addressing environmental issues and the development of electric vehicles. The fabrication and surface/interface engineering of electrode materials with refined structures are indispensable for achieving optimal performances for the different energy-related devices. Atomic layer deposition (ALD) and molecular layer deposition (MLD) techniques, the gas-phase thin film deposition processes with self-limiting and saturated surface reactions, have emerged as powerful techniques for surface and interface engineering in energy-related devices due to their exceptional capability of precise thickness control, excellent uniformity and conformity, tunable composition and relatively low deposition temperature. In the past few decades, ALD and MLD have been intensively studied for energy storage and conversion applications with remarkable progress. In this review, we give a comprehensive summary of the development and achievements of ALD and MLD and their applications for energy storage and conversion, including batteries, supercapacitors, fuel cells, solar cells, and photoelectrochemical water splitting. Moreover, the fundamental understanding of the mechanisms involved in different devices will be deeply reviewed. Furthermore, the large-scale potential of ALD and MLD techniques is discussed and predicted. Finally, we will provide insightful perspectives on future directions for new material design by ALD and MLD and untapped opportunities in energy storage and conversion.

Stable metal anodes enabled by a labile organic molecule bonded to a reduced graphene oxide aerogel

Metallic anodes (lithium, sodium, and zinc) are attractive for rechargeable battery technologies but are plagued by an unfavorable metal-electrolyte interface that leads to nonuniform metal deposition and an unstable solid-electrolyte interphase (SEI). Here we report the use of electrochemically labile molecules to regulate the electrochemical interface and guide even lithium deposition and a stable SEI. The molecule, benzenesulfonyl fluoride, was bonded to the surface of a reduced graphene oxide aerogel. During metal deposition, this labile molecule not only generates a metal-coordinating benzenesulfonate anion that guides homogeneous metal deposition but also contributes lithium fluoride to the SEI to improve Li surface passivation. Consequently, high-efficiency lithium deposition with a low nucleation overpotential was achieved at a high current density of 6.0 mA cm^-2 A Li|LiCoO₂ cell had a capacity retention of 85.3% after 400 cycles, and the cell also tolerated low-temperature (-10 °C) operation without additional capacity fading. This strategy was applied to sodium and zinc anodes as well.

Suppressing the Side Reaction by a Selective Blocking Layer to Enhance the Performance of Si-Based Anodes

Building a stable solid electrolyte interphase (SEI) is an effective method to enhance the performance of Si-based materials. However, the general strategy ignores the severe side reaction that originates from the penetration of the fluoride anion which influences the stability of the SEI. In this work, an analytical method is established to study the chemical reaction mechanism between the silicon and electrolyte by combining X-ray diffraction (XRD) with mass spectrometry (MS) technology. Additionally, a selective blocking layer coupling selectivity for the fluoride anion and a high conductivity is coated on the surface of silicon. With the protection of the selective blocking layer, the rate of the side reaction is decreased by 1700 times, and the corresponding SEI thickness is dwindled by 4 times. This work explores the mechanism of the intrinsic chemical reaction and provides future directions for improving Si-based anodes.

MXene Frameworks Promote the Growth and Stability of LiF-Rich Solid-Electrolyte Interphases on Silicon Nanoparticle Bundles

Silicon-based materials are the desirable anodes for next-generation lithium-ion batteries; however, the large volume change of Si during the charging/discharging process causes electrode fracture and an unstable solid-electrolyte interphase (SEI) layer, which severely impair their stability and Coulombic efficiency. Herein, a bundle of silicon nanoparticles is encapsulated in robust micrometer-sized MXene frameworks, in which the MXene nanosheets are precrumpled by capillary compression force to effectively buffer the stress induced by the volume change, and the abundant covalent bonds (Ti-O-Ti) between adjacent nanosheets formed through a facile thermal self-cross-linking reaction further guarantee the robustness of the MXene architecture. Both factors stabilize the electrode structure. Moreover, the abundant fluorine terminations on MXene nanosheets contribute to an in situ formation of a highly compact, durable, and mechanically robust LiF-rich SEI layer outside the frameworks upon cycling, which not only shuts down the parasitic reaction between Si and an organic electrolyte but also enhances the structural stability of MXene frameworks. Benefiting from these merits, the as-prepared anodes deliver a high specific capacity of 1797 mA h g^-1 at 0.2 A g^-1 and a high capacity retention of 86.7% after 500 cycles at 2 A g^-1 with an average Coulombic efficiency of 99.6%. Significantly, this work paves the way for other high-capacity electrode materials with a strong volume effect.

A Polymer-Reinforced SEI Layer Induced by a Cyclic Carbonate-Based Polymer Electrolyte Boosting 4.45 V LiCoO2 /Li Metal Batteries

Lithium (Li) metal batteries (LMBs) are enjoying a renaissance due to the high energy densities. However, they still suffer from the problem of uncontrollable Li dendrite and pulverization caused by continuous cracking of solid electrolyte interphase (SEI) layers. To address these issues, developing spontaneously built robust polymer-reinforced SEI layers during electrochemical conditioning can be a simple yet effective solution. Herein, a robust homopolymer of cyclic carbonate urethane methacrylate is presented as the polymer matrix through an in situ polymerization method, in which cyclic carbonate units can participate in building a stable polymer-integrated SEI layer during cycling. The as-investigated gel polymer electrolyte (GPE) assembled LiCoO₂ /Li metal batteries exhibit a fantastic cyclability with a capacity retention of 92% after 200 cycles at 0.5 C (1 C = 180 mAh g^-1 ), evidently exceeding that of the counterpart using liquid electrolytes. It is noted that the anionic ring-opening polymerization of the cyclic carbonate units on the polymer close to the Li metal anodes enables a mechanically reinforced SEI layer, thus rendering excellent compatibility with Li anodes. The in situ formed polymer-reinforced SEI layers afford a splendid strategy for developing high voltage resistant GPEs compatible with Li metal anodes toward high energy LMBs.

Developing an Interpenetrated Porous and Ultrasuperior Hard-Carbon Anode via a Promising Molten-Salt Evaporation Method

Hard carbon (HC) has become one of the prospective anode materials for sodium-ion batteries (SIBs), but its application suffers from the low electron conductivity and poor ion-diffusion kinetics. In this study, the melting and evaporation process of neutral salt was first introduced to produce nitrogen-rich interpenetrated porous HC (NIP-HC) as the anode for SIBs. Such a protocol allows for the first-demonstrated porous structure for HC materials with desired electronic conductivity and much improved rate performance than the conventional porous structure. As a result, high reversible capacity (358 mA h g^-1) and enhanced rate property (239.8 mA h g^-1 at 2 A g^-1) are achieved with improved electrode kinetics and electron conductivity because of the accelerated charge transfer derived from the unique porosity and nitrogen heteroatom-doping. More interestingly, the increase of the surface area of NIP-HC does not lead to a decrease of the initial efficiency. At the same time, a high plateau capacity (172.8 mA h g^-1) can be obtained below 0.1 V, which shows great potential for practical application in the full cells. As suggested by IG/ID from Raman tests, the degree of graphitization increases accompanied by the melting and evaporation process, which improves the electrical conductivity of the HC material as well. Furthermore, according to first-principle calculations, it is found that the nitrogen is conducive to increasing the electron density around the Fermi level, which intrinsically enhances the electrical conductivity and enriches active sites for sodium-ion storage. The result from this study has provided insights into producing interpenetrated porous HC by a simple and novel salt melting and evaporation process and enriched the methods of pore structure preparation.

Supremely elastic gel polymer electrolyte enables a reliable electrode structure for silicon-based anodes

Silicon-based materials are promising anodes for next-generation lithium-ion batteries, owing to their high specific capacities. However, the huge volume expansion and shrinkage during cycling result in severe displacement of silicon particles and structural collapse of electrodes. Here we report the use of a supremely elastic gel polymer electrolyte to address this problem and realize long-term stable cycling of silicon monoxide anodes. The high elasticity of the gel polymer electrolyte is attributed to the use of a unique copolymer consisting of a soft ether domain and a hard cyclic ring domain. Consequently, the displacement of silicon monoxide particles and volume expansion of the electrode were effectively reduced, and the damage caused by electrode cracking is alleviated. A SiO|LiNi0.5Co0.2Mn0.3O2 cell shows 70.0% capacity retention in 350 cycles with a commercial-level reversible capacity of 3.0 mAh cm-2 and an average Coulombic efficiency of 99.9%.

Graphene-Modified 3D Copper Foam Current Collector for Dendrite-Free Lithium Deposition

Lithium (Li) metal is regarded as the ideal anode for rechargeable Li-metal batteries such as Li-S and Li-air batteries. A series of problems caused by Li dendrites, such as low Coulombic efficiency (CE) and a short circuit, have limited the application of Li-metal batteries. In this study, a graphene-modified three-dimensional (3D) Copper (Cu) current collector is addressed to enable dendrite-free Li deposition. After Cu foam is immersed into graphene oxide (GO) suspension, a spontaneous reduction of GO, induced by Cu, generates reduced graphene oxide on a 3D Cu (rGO@Cu) substrate. The rGO@Cu foam not only provides large surface area to accommodate Li deposition for lowering the local effective current density, but also forms a rGO protective layer to effectively control the growth of Li dendrites. As current collector, the rGO@Cu foam shows superior properties than commercial Cu foam and planar Cu foil in terms of cycling stability and CE. The rGO@Cu foam delivers a CE as high as 98.5% for over 350 cycles at the current density of 1 mA cm⁻². Furthermore, the full cell using LiFePO₄ as cathode and Li metal as anode with rGO@Cu foam as current collector (LiFePO₄/rGO@Cu-Li) is assembled to prove the admirable capacities and indicates commercialization of Li-metal batteries.

Nucleation and Growth Mechanism of Lithium Metal Electroplating

Understanding the mechanism of Li nucleation and growth is essential for providing long cycle life and safe lithium ion batteries or lithium metal batteries. However, no quantitative report on Li metal deposition is available, to the best of our knowledge. We propose a model for quantitatively understanding the Li nucleation and growth mechanism associated with the solid-electrolyte interphase (SEI) formation, which we name the Li-SEI model. The current transients at various overpotentials initiate the nucleation and growth of Li metal on bare Cu foil. The Li-SEI model considering a three-dimensional diffusion-controlled instantaneous process (J_3D-DC) with the simultaneous reduction of electrolyte decomposition (J_SEI) due to the SEI fracture is employed for investigating the Li nucleation and growth mechanism. The individual contributions of experimental and theoretical transient states, i.e., the fundamental kinetic values of diffusion coefficient (D), rate of nucleation (N₀), and rate constant of electrolyte decomposition (k_SEI), can be determined from the Li-SEI model. Interestingly, J_SEI increases with time, indicating that the current contributing from the electrolyte decomposition increases with time due to the SEI fracture upon Li deposition. Meanwhile, the k_SEI increases with overpotential, indicating the SEI fracture is more serious at higher overpotential or higher growth rate. The k_SEI is smaller in the electrolyte with fluoroethylene carbonate (FEC) additive, indicating that FEC additive can significantly suppress the SEI fracture during Li metal deposition. This proposed model opens a new way to quantitatively understand the Li nucleation and growth mechanism and electrolyte decomposition on various substrates or in different electrolytes.

Silicon Carbide as a Protective Layer to Stabilize Si-Based Anodes by Inhibiting Chemical Reactions

Developing a practical silicon-based (Si-based) anode is a precondition for high-performance lithium-ion batteries. However, the chemical reactivity of the Si renders it liable to be consumed, which must be completely understood for it to be used in practical battery systems. Here, a fresh and fundamental mechanism is proposed for the rapid failure of Si-based materials. Silicon can chemically react with lithium hexafluorophosphate (LiPF₆) to constantly generate lithium hexafluorosilicate (Li₂SiF₆) aggregates during cycling. In addition, nanocarbon coated on silicon acts as a catalyst to accelerate such detrimental reactions. By taking advantage of the high strength and toughness of silicon carbide (SiC), a SiC layer is introduced between the inner silicon and outer carbon layers to inhibit the formation of Li₂SiF₆. The side reaction rate decreases significantly due to the increase in the activation energy of the reaction. Si@SiC@C maintains a specific capacity of 980 mAh g^-1 at a current density of 1 A g^-1 after 800 cycles with an initial Coulombic efficiency over 88.5%. This study will contribute to improved design of Si-based anode for high-performance Li-ion batteries.

Minimized Volume Expansion in Hierarchical Porous Silicon upon Lithiation

Silicon (Si) remains one of the most promising anode materials for next-generation lithium-ion batteries (LIBs). The key challenge for Si anodes is the huge volume change during lithiation-delithiation cycles that leads to electrode pulverization and rapid capacity fading. Here, we report a hierarchical porous Si (hp-Si) with a tailored porous structure [tunable primary pores (20-200 nm) and secondary nanopores (∼3-10 nm)] that can effectively minimize the volume expansion. An in situ transmission electron microscopy (TEM) study revealed that the hp-Si material with the same porosity but larger primary pores can more effectively accommodate lithiation-induced volume expansion, giving rise to a much reduced apparent volume expansion on both material and electrode levels. Chemomechanical modeling revealed that because of the different relative stiffnesses of the lithiated and unlithiated Si phases, the primary pore size plays a key role in accommodating the volume expansion of lithiated Si. The higher structural stability of the hp-Si materials with larger primary pores also maintains the fast diffusion channels of the connective pores, giving rise to better power capability and capacity retention upon electrochemical cycling. Our findings point toward an optimized hp-Si material with minimal volume change during electrochemical cycling for next-generation LIBs.

Metallothermic Reduction of Molten Adduct [PCl4+][AlCl4-] at 50 °C to Amorphous Phosphorus or Crystallized Phosphides

A molten salt metallothermic reduction strategy is developed for preparing phosphorus (P) or phosphides controllably at low temperature, which is simple, energy-saving, and easy to scale up. Typically, synthesis of spongelike porous amorphous P (a-P) is realized through reduction of PCl₅ with Zn (or Al) at 50 °C assisted by AlCl₃. It is demonstrated that an adduct salt PCl₅·AlCl₃ composed of PCl₄⁺ and AlCl₄^- ions with a low melting point below 50 °C is formed from covalent salts PCl₅ and AlCl₃. This system is also suitable for producing nanostructured phosphides by adding corresponding transition-metal (Co, Fe, and Cu) chlorides even at 50 °C. As a Li storage anode, the as-prepared a-P exhibits a capacity of 1605 mA h g^-1 at 0.2 C, a good rate capability of 1283 mA h g^-1 at 10 C, and a long-term cycling stability of 1082 mA h g^-1 after 200 cycles. Additionally, the Na-/K-ion storage performance is investigated systematically.

Enabling Lithium-Metal Anode Encapsulated in a 3D Carbon Skeleton with a Superior Rate Performance and Capacity Retention in Full Cells

Suppressing the formation of lithium (Li) dendrites is central to implementing Li-metal anode, which has gained growing attention due to its ultrahigh specific capacity and low redox potential. Here, a novel approach is adopted to deposit Li-metal within a rigid three-dimensional (3D) carbon paper (3DCP) network, which consists of a cross-link framework of carbon fibers and graphene nanosheets (GNs). This unique structure yields a uniform distribution of Li-nuclei during the preliminary stage of Li-plating and the formation of a stable solid-electrolyte interface. The as-obtained anode can deliver a high areal capacity of 10 mAh cm^-2 without the dendritic formation after 1000 cycles in a Li@3DCP/LiFePO₄ full cell at 4 C. In addition, the Li@3DCP anode displays low voltage platform (<20 mV at 1 mA cm^-2), high plating/stripping efficiency (99.0%), and long lifespan (>1000 h). When coupled with LiNi_0.8Co_0.15Al_0.05O₂ cathode, the Li@3DCP electrode exhibits a superior rate capability up to 10 C and high temperature performance (60 °C). The unprecedented performance is attributed to the desirable combination of micro/nanostructures in 3DCP, in which carbon fiber framework provides the mechanical stability for volume change, whereas numerous lithiophilicity sites on GNs enable the suppression of Li-dendrite growth.

A Dual-Salt Gel Polymer Electrolyte with 3D Cross-Linked Polymer Network for Dendrite-Free Lithium Metal Batteries

Lithium metal batteries show great potential in energy storage because of their high energy density. Nevertheless, building a stable solid electrolyte interphase (SEI) and restraining the dendrite growth are difficult to realize with traditional liquid electrolytes. Solid and gel electrolytes are considered promising candidates to restrain the dendrites growth, while they are still limited by low ionic conductivity and incompatible interphases. Herein, a dual-salt (LiTFSI-LiPF6) gel polymer electrolyte (GPE) with 3D cross-linked polymer network is designed to address these issues. By introducing a dual salt in 3D structure fabricated using an in situ polymerization method, the 3D-GPE exhibits a high ionic conductivity (0.56 mS cm-1 at room temperature) and builds a robust and conductive SEI on the lithium metal surface. Consequently, the Li metal batteries using 3D-GPE can markedly reduce the dendrite growth and achieve 87.93% capacity retention after cycling for 300 cycles. This work demonstrates a promising method to design electrolytes for lithium metal batteries.

Controlling Nucleation in Lithium Metal Anodes

Rechargeable batteries are regarded as the most promising candidates for practical applications in portable electronic devices and electric vehicles. In recent decades, lithium metal batteries (LMBs) have been extensively studied due to their ultrahigh energy densities. However, short lifespan and poor safety caused by uncontrollable dendrite growth hinder their commercial applications. Besides, a clear understanding of Li nucleation and growth has not yet been obtained. In this Review, the failure mechanisms of Li metal anodes are ascribed to high reactivity of lithium, virtually infinite volume changes, and notorious dendrite growth. The principles of Li deposition nucleation and early dendrite growth are discussed and summarized. Correspondingly, four rational strategies of controlling nucleation are proposed to guide Li nucleation and growth. Finally, perspectives for understanding the Li metal deposition process and realizing safe and high-energy rechargeable LMBs are given.

Robust Expandable Carbon Nanotube Scaffold for Ultrahigh-Capacity Lithium-Metal Anodes

There has been a renewed interest in using lithium (Li) metal as an anode material for rechargeable batteries owing to its high theoretical capacity of 3860 mA h g^-1 . Despite extensive research, modifications to effectively inhibit Li dendrite growth still result in decreased Li loading and Li utilization. As a result, real capacities are often lower than values expected, if the total mass of the electrode is taken into consideration. Herein, a lightweight yet mechanically robust carbon nanotube (CNT) paper is demonstrated as a freestanding framework to accommodate Li metal with a Li mass fraction of 80.7 wt%. The highly conductive network made of sp2-hybridized carbon effectively inhibits formation of Li dendrites and affords a favorable coulombic efficiency of >97.5%. Moreover, the Li/CNT electrode retains practical areal and gravimetric capacities of 10 mA h cm^-2 and 2830 mA h g^-1 (vs the mass of electrode), respectively, with 90.9% Li utilization for 1000 cycles at a current density of 10 mA cm^-2 . It is demonstrated that the robust and expandable nature is a distinguishing feature of the CNT paper as compared to other 3D scaffolds, and is a key factor that leads to the improved electrochemical performance of the Li/CNT anodes.

Understanding Fluoroethylene Carbonate and Vinylene Carbonate Based Electrolytes for Si Anodes in Lithium Ion Batteries with NMR Spectroscopy

Fluoroethylene carbonate (FEC) and vinylene carbonate (VC) are widely used as electrolyte additives in lithium ion batteries. Here we analyze the solid electrolyte interphase (SEI) formed on binder-free silicon nanowire (SiNW) electrodes in pure FEC or VC electrolytes containing 1 M LiPF₆ by solid-state NMR with and without dynamic nuclear polarization (DNP) enhancement. We find that the polymeric SEIs formed in pure FEC or VC electrolytes consist mainly of cross-linked poly(ethylene oxide) (PEO) and aliphatic chain functionalities along with additional carbonate and carboxylate species. The formation of branched fragments is further confirmed by ¹³C-¹³C correlation NMR experiments. The presence of cross-linked PEO-type polymers in FEC and VC correlates with good capacity retention and high Coulombic efficiencies of the SiNWs. Using ²⁹Si DNP NMR, we are able to probe the interfacial region between SEI and the Si surface for the first time with NMR spectroscopy. Organosiloxanes form upon cycling, confirming that some of the organic SEI is covalently bonded to the Si surface. We suggest that both the polymeric structure of the SEI and the nature of its adhesion to the redox-active materials are important for electrochemical performance.

Achieving Ultrafast and Stable Na-Ion Storage in FeSe2 Nanorods/Graphene Anodes by Controlling the Surface Oxide

Designing transitional metal selenides (TMSes) with superior rate and cyclic performance for sodium-ion storage remains great challenges. To achieve this task, the influence of surface oxides on Na-ion storage behavior of FeSe₂ is investigated by designing FeSe₂ with varying oxide content. It is found that surface oxide has an inhibitory effect on the activity of FeSe₂. Small-sized FeSe₂ on graphene with higher surface oxide content exhibits obviously inferior performance compared to large-sized FeSe₂ with lower oxide content. By controlling oxide content, the prepared FeSe₂ nanorods/graphene exhibits a high capacity of 459 mAh/g at 0.1 A/g and superior rate performance. Only 10% capacity decrease occurs with the increase in current density from 0.1 to 5 A/g. Even at 25 A/g (∼50 C), it delivers a capacity of 227 mAh/g with almost no decay after 800 cycles. The influence mechanism of surface oxide is investigated. The oxide can be converted to a sodiated shell with high mechanical strength and poor conductivity, which generates phase-transition resistance to suppress the sodiation of FeSe₂ core, blocks the transfer of Na-ions and electrons in subsequent sodiation processes. Understanding the effect of surface oxide on Na-ion storage will be helpful in designing TMSes and other active materials.