Chemical Alignment of Oxidatively Shortened Single-Walled Carbon Nanotubes on Silver Surface

Enhancing the Interaction of Carbon Nanotubes by Metal-Organic Decomposition with Improved Mechanical Strength and Ultra-Broadband EMI Shielding Performance

The remarkable properties of carbon nanotubes (CNTs) have led to promising applications in the field of electromagnetic interference (EMI) shielding. However, for macroscopic CNT assemblies, such as CNT film, achieving high electrical and mechanical properties remains challenging, which heavily depends on the tube-tube interactions of CNTs. Herein, we develop a novel strategy based on metal-organic decomposition (MOD) to fabricate a flexible silver-carbon nanotube (Ag-CNT) film. The Ag particles are introduced in situ into the CNT film through annealing of MOD, leading to enhanced tube-tube interactions. As a result, the electrical conductivity of Ag-CNT film is up to 6.82 × 105 S m-1, and the EMI shielding effectiveness of Ag-CNT film with a thickness of ~ 7.8 μm exceeds 66 dB in the ultra-broad frequency range (3-40 GHz). The tensile strength and Young's modulus of Ag-CNT film increase from 30.09 ± 3.14 to 76.06 ± 6.20 MPa (~ 253%) and from 1.12 ± 0.33 to 8.90 ± 0.97 GPa (~ 795%), respectively. Moreover, the Ag-CNT film exhibits excellent near-field shielding performance, which can effectively block wireless transmission. This innovative approach provides an effective route to further apply macroscopic CNT assemblies to future portable and wearable electronic devices.

Soft cutting of single-wall carbon nanotubes by low temperature ultrasonication in a mixture of sulfuric and nitric acids

To decrease single-wall carbon nanotube (SWCNT) lengths to a value of 100-200 nm, aggressive cutting methods, accompanied by a high loss of starting material, are frequently used. We propose a cutting approach based on low temperature intensive ultrasonication in a mixture of sulfuric and nitric acids. The method is nondestructive with a yield close to 100%. It was applied to cut nanotubes produced in three different ways: gas-phase catalysis, chemical vapor deposition, and electric-arc-discharge methods. Raman and Fourier transform infrared spectroscopy were used to demonstrate that the cut carbon nanotubes have a low extent of sidewall degradation and their electronic properties are close to those of the untreated tubes. It was proposed to use the spectral position of the far-infrared absorption peak as a simple criterion for the estimation of SWCNT length distribution in the samples.

Facile preparation of carbon nanotube-conducting polymer network for sensitive electrochemical immunoassay of Hepatitis B surface antigen in serum

A novel electrochemical immunosensor built on three dimensional carbon nanotube-conducting polymer (CNT-CP) network is reported for detection of Hepatitis B surface antigen (HBsAg) in human serum. The CNT-CP network is prepared by drop-drying of CNT solution on glassy carbon electrode, followed by electrochemical polymerization of poly (pyrrole propionic acid) (pPPA) film to crosslink and stabilize the CNTs, wherein the CNTs form the backbone of the network, and offer great specific surface areas for antibody attachment, and confer good conductivity for electrochemical detection, while the conducting film integrates the carbon nanotubes into a stable network due to its self-limiting growth behavior and provides abundant carboxyl groups for covalent immobilization of probe proteins. As a unique matrix, the CNT-CP network enables sensitive electrochemical detection of HBsAg biomarker by using alkaline phosphatase (ALP)-conjugated secondary antibodies under sandwich format coupling with the ALP substrate solution, p-aminophenyl phosphate (PAPP), reaching a detection limit of 0.01ng/mL with a dynamic range of 5 orders of magnitude.

DNA-CNT nanowire networks for DNA detection

The ability to detect biological analytes in a rapid, sensitive, operationally simple, and cost-effective manner will impact human health and safety. Hybrid biocatalyzed-carbon nanotube (CNT) nanowire-based detection methods offer a highly sensitive and specific platform for the fabrication of simple and effective conductometric devices. Here, we report a conductivity-based DNA detection method utilizing carbon nanotube-DNA nanowire devices and oligonucleotide-functionalized enzyme probes. Key to our sensor design is a DNA-linked-CNT wire motif, which forms a network of interrupted carbon nanotube wires connecting two electrodes. Sensing occurs at the DNA junctions linking CNTs, followed by amplification using enzymatic metalization leading to a conductimetric response. The DNA analyte detection limit is 10 fM with the ability to discriminate single, double, and triple base pair mismatches. DNA-CNT nanowires and device sensing gaps were characterized by scanning electron microscopy (SEM) and confocal Raman microscopy, supporting the enhanced conductometric response resulting from nanowire metallization.

Strategies for post-synthesis alignment and immobilization of carbon nanotubes

Carbon nanotubes (CNTs) have developed into a standard material used as a building block for nanotechnological developments. Based on the unique properties that make CNTs useful for many different applications in nanotechnology, optics, electronics, and material science, there has been a rapid development of this research area and many different applications have emerged in the past few years. Frequently, the alignment and immobilization of CNTs play an important role for many applications and different strategies, in particular post-synthesis approaches, can be applied. Recent developments of different techniques to immobilize and align carbon nanotubes are discussed and classified into three main categories: chemical immobilization and alignment, physical immobilization and alignment, and the use of external fields for these purposes. Many of the techniques involve multiple steps and may also cross these rather crudely defined boundaries. As such, the techniques are classified according to their most important or unique step.

Chemically grafted carbon nanotube surface coverage gradients

Two approaches to producing gradients of vertically aligned single-walled carbon nanotubes (SWCNTs) on silicon surfaces by chemical grafting are presented here. The first approach involves the use of a porous silicon (pSi) substrate featuring a pore size gradient, which is functionalized with 3-aminopropyltriethoxysilane (APTES). Carboxylated SWCNTs are then immobilized on the topography gradient via carbodiimide coupling. Our results show that as the pSi pore size and porosity increase across the substrate the SWCNT coverage decreases concurrently. In contrast, the second gradient is an amine-functionality gradient produced by means of vapor-phase diffusion of APTES from a reservoir onto a silicon wafer where APTES attachment changes as a function of distance from the APTES reservoir. Carboxylated SWCNTs are then immobilized via carbodiimide coupling to the amine-terminated silicon gradient. Our observations confirm that with decreasing APTES density on the surface the coverage of the attached SWCNTs also decreases. These gradient platforms pave the way for the time-efficient optimization of SWCNT coverage for applications ranging from field emission to water filtration to drug delivery.

Patterning of hierarchically aligned single-walled carbon nanotube Langmuir-Blodgett films by microcontact printing

We present a patterning method for hierarchically aligned assembly of single-walled carbon nanotubes (SWNTs) using a combination of the Langmuir-Blodgett (LB) technique and soft lithography. The LB technique allows one to control the alignment and the surface density of SWNTs by adjusting surface pressure of the film at the air-water interface. The aligned SWNT Langmuir films are successfully transferred onto the polydimethylsiloxane (PDMS) or silicon substrate with unidirectional alignment, and SWNT patterns with various shapes are fabricated on silicon and flexible poly(ethylene terephthalate) (PET) substrates by contacting and peeling off the PDMS stamp from the substrates via microcontact printing or lift-up methods. The SWNT patterning technique using the combination of soft lithography and the LB method can be applied in various fields, such as flexible high-speed transistors, high-efficiency solar cells, and transparent electrodes.

Regiospecific synthesis of Au-nanorod/SWCNT/Au-nanorod heterojunctions

The synthesis of precisely defined nanoscale hybrid materials remains a challenge at the frontier of chemistry and material science. In particular, the assembly of diverse high-aspect ratio one-dimensional materials such as gold nanorods and carbon nanotubes into functional systems is of ever increasing interest due to their electronic and sensing applications. To meet these challenges, methods for interfacing gold nanorods with carbon materials such as single-walled carbon nanotubes (SWCNTs) in a regio-controlled manner are needed. Herein, we report a method for the regiospecific synthesis of terminally linked gold nanorod-SWCNTs based on a nanotube surface protection strategy. The key to our approach is a SWCNT surface protection procedure allowing for selective functionalization of the SWCNT termini.

Vertically aligned single-walled carbon nanotubes by chemical assembly--methodology, properties, and applications

Single-walled carbon nanotubes (SWNTs), as one of the most promising one-dimension nanomaterials due to its unique structure, peculiar chemical, mechanical, thermal, and electronic properties, have long been considered as an important building block to construct ordered alignments. Vertically aligned SWNTs (v-SWNTs) have been successfully prepared by using direct growth and chemical assembly strategies. In this review, we focus explicitly on the v-SWNTs fabricated via chemical assembly strategy. We provide the readers with a full and systematic summary covering the advances in all aspects of this area, including various approaches for the preparation of v-SWNTs using chemical assembly techniques, characterization, assembly kinetics, and electrochemical properties of v-SWNTs. We also review the applications of v-SWNTs in electrochemical and bioelectrochemical sensors, photoelectric conversion, and scanning probe microscopy.

[60]-fullerene and single-walled carbon nanotube-based ultrathin films stepwise grafted onto a self-assembled monolayer on ITO

A step-by-step method was used to prepare homogeneous ultrathin films composed of [60]-fullerene (C60) and single-walled carbon nanotubes (SWNTs), grafted onto the functional surface of an alkylsilane self-assembled monolayer (SAM) on an ITO substrate with an ITO-C60-SWNT sequence using amine addition across a double bond in C60 followed by amidation coupling with acid-functionalized SWNTs. Atomic force microscope and scanning electron microscope images of the resulting composite film showed two-component ball-tube microstructures with high-density coverage, where C60 was homogeneously distributed in the SWNT forest. The attachment of SWNTs to the residual amine units in the SAM on the ITO substrate (SAM-ITO) as well as on the C60 sphere results in the C60 molecules in the aggregated clusters being more separately dispersed, which forms a densely packed composite film as a result of the pi-pi interaction between the C60 buckyballs and the SWNT walls. It was found using ferrocene as an internal redox probe that the oxidative and reductive processes at the film-solution surface were effectively retarded because of obstruction from the densely packed film and the electronic effect of SWNT and C60. In addition, the electrochemical properties of C60 on SAM-ITO plates observed by cyclic voltammetry were significantly modified by chemical anchorage using SWNTs. X-ray photoelectron spectroscopy (XPS) analysis also indicated the successful grafting of C60 and SWNT. The XPS chemical shift of the binding energy showed the presence of electronic interactions between C60, SWNT, and ITO components. Such a uniformly distributed C60-SWNT film may be useful for future research in electrochemical and photoactive nanodevices.

Effects of carbon nanotubes (CNTs) on the processing and in-vitro degradation of poly(DL-lactide-co-glycolide)/CNT films

Nanocomposite films based on single wall carbon nanotubes (SWNTs) and poly(DL-lactide-co-glycolide) copolymer (50:50 PLGA) were processed and analyzed. The purpose of this study was to investigate the effect of different functionalization systems on the physical stability and morphology of PLGA films. Both covalent and non covalent functionalization of carbon nanotubes were considered in order to control the interactions between PLGA and SWNTs and to understand the role of the filler in the biodegradation properties. Using a solvent casting process, different PLGA/SWNT nanocomposites were prepared and incubated using organic solution under physiological conditions. In-vitro degradation studies were conducted by measurements of weight loss, infrared spectroscopy, glass transition temperature and SEM observations as a function of the incubation time, over a 9-week period. All PLGA films were degraded by hydrolitical degradation. However, a different degradation mechanism was observed in the case of functionalized SWNTs with respect to pristine material. It has been observed that system composition and SWNT functionalization may play a crucial role on the autocatalytic effect of the degradation process. These studies suggest that the degradation kinetics of the films can be engineered by varying carbon nanotube (CNT) content and functionalization. The combination of biodegradable polymers and CNTs opens a new perspective in the self-assembly of nanomaterials and nanodevices.

A general route to prepare one- and three-dimensional carbon nanotube/metal nanoparticle composite nanostructures

Adsorption of polyethyleneimine (PEI)-metal ion complexes onto the surfaces of carbon nanotubes (CNTs) and subsequent reduction of the metal ion leads to the fabrication of one-dimensional CNT/metal nanoparticle (CNT/M NP) heterogeneous nanostructures. Alternating adsorption of PEI-metal ion complexes and CNTs on substrates results in the formation of multilayered CNT films. After exposing the films to NaBH4, three-dimensional CNT composite films embedded with metal nanoparticles (NPs) are obtained. UV-visible spectroscopy, scanning electron microscopy, and X-ray photoelectron spectroscopy are used to characterize the film assembly. The resulting (CNT/M NP)n films inherit the properties from both the metal NPs and CNTs that exhibit unique performance in surface-enhanced Raman scattering (SERS) and electrocatalytic activities to the reduction of O2; as a result, they are more attractive compared to (CNT/polyelectrolyte)n and (NP/polyelectrolyte)n films because of their multifunctionality.

Superhydrophobic bionic surfaces with hierarchical microsphere/SWCNT composite arrays

Superhydrophobic bionic surfaces with hierarchical micro/nano structures were synthesized by decorating single-walled or multiwalled carbon nanotubes (CNTs) on monolayer polystyrene colloidal crystals using a wet chemical self-assembly technique and subsequent surface treatment with a low surface-energy material of fluoroalkylsilane. The bionic surfaces are based on the regularly ordered colloidal crystals, and thus the surfaces have a uniform superhydrophobic property on the whole surface. Moreover, the wettability of the bionic surface can be well controlled by changing the distribution density of CNTs or the size of polystyrene microspheres. The morphologies of the synthesized bionic surfaces bear much resemblance to natural lotus leaves, and the wettability exhibited remarkable superhydrophobicity with a water contact angle of about 165 degrees and a sliding angle of 5 degrees.

Wet chemical needlelike assemblies of single-walled carbon nanotubes on a silicon surface

Single-walled carbon nanotubes (SWCNT) have been organized covalently to form a uniform needlelike structure on a silicon surface using a wet chemical assembly technique. In this work, we successfully combine silanization with the condensation reaction of the carboxylic group with the amino group.

Advances in carbon-nanotube assembly

Iijima's observation in 1991 of fullerene-like materials by high-resolution transmission electron microscopy heralded the beginning of the carbon nanotube (CNT) era. A wealth of theoretical predictions and experimental verifications about CNTs have disclosed remarkable size- and structure-dependent properties that are attractive for various potential applications, ranging from conducting wires in molecular devices to fillers in nanocomposites. Many of these applications require assembly (alignment and/or patterning) of CNTs into hierarchical arrays over large-scale areas with controllable shape, location, orientation, and density of the nanotubes. Efforts from both the scientific and engineering points of view have been made to address this issue, beginning shortly after the discovery of CNTs. We review here the development of CNT-assembly techniques under the two rubrics of synthetic assembly and post-synthetic assembly, with emphasis given to the post-synthetic approach. Preliminary to the survey of assembly techniques, we also discuss the characterization techniques that have been widely used for the challenging tasks of visualizing and quantifying CNT assembly.

Preparation and characterisation of an aligned carbon nanotube array on the silicon (100) surface

Arrays of aligned carbon nanotubes formed by self-assembly on a Si (100) surface are described. The surface of a Si (100) wafer has been modified by reaction of hydride-terminated Si (100) with ethyl undecylenate to give ethyl undecanoate self-assembled monolayers (SAMs) which were linked by stable silicon-carbon covalent bonds. The ester terminus of the monolayer was converted to an alcohol whereupon shortened carbon nanotubes were covalently attached using carbodiimide coupling. The formation of the SAM and its subsequent modification with nanotubes has been followed using a series of techniques including X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), scanning electron microscopy (SEM), IR spectroscopy and cyclic voltammetry.

Trapping, Pattern Formation, and Ordering of Polyelectrolyte/Single-Wall Carbon Nanotube Complexes at the Air/Water and Air/Solid Interfaces

The Langmuir and Langmuir-Blodgett (LB) techniques have been applied in a novel approach to build structurally well-ordered, oriented, and organized assemblies of water-soluble single-wall carbon nanotubes (ws-SWCNTs) at the air/water and air/solid interfaces. The SWCNTs were rendered hydrophilic by complexing them with a quenched polyelectrolyte. We observed that the ws-SWCNT concentration at the air/water interface increases with time condensing into different patterns, among which are isolated soap-froths, rings, and the aggregation of cumuli-like 2D-structures. These patterns were recorded at different compression-expansion stages by Brewster angle microscopy (BAM). From the isotherm measurements, we are able to determine the diffusion process by which ws-SWCNT concentration builds up at the water surface. The corresponding LB films were very stable and could be transferred onto mica substrates easily. Atomic force microscopy (AFM) images revealed that the morphology of these films is surface-pressure dependent, and aligned structures with a nematic-like order formed closely packed mono- or multilayer films. The assembly of 2D-nanostructures by means of this approach offers a great potential for emergent technological applications using modified water-soluble SWCNTs.

Electrochemistry at Chemically Assembled Single-Wall Carbon Nanotube Arrays

Single-wall carbon nanotubes (SWNTs) chemically assembled on gold substrates were employed as electrodes to investigate the charge transfer process between SWNTs and the underlying substrates. Cyclic voltammetry (CV) indicates that the assembled SWNTs allow electron communication between a gold electrode and the redox couple in solution, though the SWNTs are linked directly onto the insulating monolayer of 11-amino-n-undecanethiol (AUT) on the Au substrate. An electron transfer (ET) mechanism, which contains an electron tunneling process across the AUT monolayer, is proposed to explain the CV behavior of Au/AUT/SWNT electrodes. Electrochemical measurements show that the apparent electron tunneling resistance, which depends on the surface density of assembled SWNTs, has apparent effects similar to those of solution resistance on CV behavior . The theory of solution resistance is used to describe the apparent tunneling resistance. The experimental results of the dependence of ET parameter psi on the potential scan rate upsilon are in good agreement with the theoretical predictions. Kinetic studies of the chemical assembly of SWNTs by atomic force microscopic (AFM), electrochemical, and Raman spectroscopic methods reveal that two distinct assembly kinetics exist: a relatively fast step that is dominated by the surface reaction, and a successive slow step that is governed by bundle formation.