Influence of solvent on ion aggregation and transport in PY15TFSI ionic liquid-aprotic solvent mixtures

Morphological Features of SiO2 Nanofillers Address Poor Stability Issue in Gel Polymer Electrolyte-Based Electrochromic Devices

Nanofillers' applicability in gel polymer electrolyte (GPE)-based devices skyrocketed in the last decade as soon as their remarkable benefits were realized. However, their applicability in GPE-based electrochromic devices (ECDs) has hardly seen any development due to challenges such as optical inhomogeneity brought by incompetent nanofiller sizes, transmittance drop due to higher filler loading (usually required), and poor methodologies of electrolyte fabrication. To address such issues, herein, we demonstrate a reinforced polymer electrolyte tailored through poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP),1-butyl-3-methylimidazolium tetrafluoroborate (BMIMBF₄), and four types of mesoporous SiO₂ nanofillers, porous (distinct morphologies) and nonporous, two each. The synthesized electrochromic species 1,1'-bis(4-fluorobenzyl)-4,4'-bipyridine-1,1'-diium tetrafluoroborate (BzV, 0.05 M), counter redox species ferrocene (Fc, 0.05 M), and supporting electrolyte (TBABF₄, 0.5 M) were first dissolved in propylene carbonate (PC) and then immobilized in an electrospun PVDF-HFP/BMIMBF₄/SiO₂ host. We distinctly observed that spherical (SPHS) and hexagonal pore (MCMS) morphologies of fillers endowed higher transmittance change (ΔT) and coloration efficiency (CE) in utilized ECDs; particularly for the MCMS-incorporated ECD (GPE-MCMS/BzV-Fc ECD), ΔT reached ∼62.5% and CE soared to 276.3 cm²/C at 603 nm. The remarkable benefit of filler's hexagonal morphology was also seen in the GPE-MCMS/BzV-Fc ECD, which not only marked an astounding ionic conductivity (σ) of ∼13.5 × 10^-3 S cm^-1 at 25 °C, thus imitating the solution-type ECD's behavior, but also retained ∼77% of initial ΔT after 5000 switching cycles. The enhancement in ECD's performance resulted from merits brought by filler geometries such as the proliferation of Lewis acid-base interaction sites due to the high surface-to-volume ratio, the creation of percolating tunnels, and the emergence of capillary forces triggering facile ion transportation in the electrolyte matrix.

Evidence for Ion Association at the Gas-Liquid Interface of the Mixture of 1-Butyl-3-methylimidazolium Hexafluorophosphate and Benzonitrile: A Sum Frequency Generation Spectroscopy and Surface Tension Study

The gas-liquid interface for the mixtures of [BMIM][PF₆] and benzonitrile is studied by sum frequency generation (SFG) spectroscopy and surface tension measurements as an important solute to reduce the viscosity of ionic liquids. Solvation of ionic compounds in bulk solvent is not necessarily the same as that at the surface due to the lower dielectric medium at the air/liquid interface. The results from the temperature-dependent SFG spectroscopy and surface tension study suggest that the ionic liquid in a benzonitrile solvent is associated as ion pairs at the surface rather than as dissociated─solvated─ions in the bulk solution. The influence of ionic liquids on the surface structure of benzonitrile is investigated from 0 to 1.0 mole fraction of benzonitrile. The CH stretching mode of vibration of benzonitrile in the SFG spectrum begins from a 0.2 mole fraction (x) of benzonitrile, and the intensity of the peak constantly increases on increasing the concentration of benzonitrile. However, the addition of benzonitrile does not result in extra peaks or shifting of the peak frequency to the spectra of [BMIM][PF₆]. The surface tension measurements further support the presence of benzonitrile at the gas-liquid interface. The surface tension data of the mixture smoothly decrease as the benzonitrile concentration increases. The apparent tilt angle of the terminal methyl group of the cation of [BMIM][PF₆] is calculated from SFG polarization spectra and shows an apparent lowering with the addition of benzonitrile. The effect of temperature on the surface structure of the binary mixture is also reported at four different temperatures between -15 and 40 °C for both the SFG spectroscopy and surface tension study. Benzonitrile shows different behavior in the mixture at higher temperatures than pure benzonitrile, as observed in the SFG spectra. In contrast, it does not show any CN peak in the mixture below 0.9 mole fraction. The temperature dependence of the interfacial tension is used to evaluate thermodynamic functions such as surface entropy and surface enthalpy. Both were found to be lowered with the increasing concentration of benzonitrile. Both spectroscopic and thermodynamic analyses indicate that the ionic liquid is highly associated as ion pairs and the benzonitrile is more ordered at the surface at concentration <0.4×.

Ionic Liquid Solutions Show Anomalous Crowding Behavior at an Electrode Surface

X-ray reflectivity was used to study the several-nanometer-thick "crowded" layers that form at the interfaces between a planar electrode and concentrated solutions of ionic liquids. The ionic liquid [P_14,6,6,6]⁺[NTf₂]^- was dissolved in either strongly polar propylene carbonate or weakly polar dimethyl carbonate. In the range of 19-100 vol % ionic liquid, between working electrode potentials +2 and +2.75 V, uniform 2-7 nm thick interfacial layers were observed. These layers are not pure anions but contain three to five times as many anions as cations and about the same percentage of solvent as the bulk solution. On the other side of the layer, the density is that of the bulk solution. These features are inconsistent with a picture of the crowded layer as a region of pure, close-packed counterions. Not only the layer thickness but also the charge density decrease with increasing dilution at any given applied voltage. This appears to indicate, counterintuitively, that a thinner layer with lower net charge density will screen an electric field as effectively as a thicker layer with higher charge density.

Developing high voltage Zn(TFSI)2/Pyr14TFSI/AN hybrid electrolyte for a carbon-based Zn-ion hybrid capacitor

Aqueous Zn-ion hybrid capacitors (ZIHCs), integrating the typical characteristics of Zinc ion batteries and supercapacitors, have become a promising candidate to replace or supplement lithium-ion energy storage technology. However, the narrow operating voltage window and the instability of the Zn/electrolyte interface caused by aqueous solvents have become a great challenge for practical applications. Here, we developed a new type of hybrid electrolyte (Zn(TFSI)₂/[[Pyr₁₄TFSI]₃]₁₆/[AN]₄) based on the organic solvent (AN) combined with ionic liquid (Pyr₁₄TFSI) and Zn salt (Zn(TFSI)₂). This non-flammable electrolyte benefited from the synergistic advantages of Pyr₁₄TFSI and AN, and could output a wide electrochemical window (3.32 V vs. Zn/Zn²⁺) and good compatibility with metallic Zn, while possessing excellent wettability. Theoretical and experimental results further reveal that such superb performance originates from the change of Zn coordination environment. Consequently, the constructed ZIHC displays a stable cycling performance (10 000 cycles at 5 A g^-1 without significant capacity fade) and a high operating voltage of 2.1 V. This newly developed electrolyte, which solves the conventional interface problem and improves the voltage window, will promote the development of ZIHCs.

The Use of Succinonitrile as an Electrolyte Additive for Composite-Fiber Membranes in Lithium-Ion Batteries

In the present work, the effect of temperature and additives on the ionic conductivity of mixed organic/ionic liquid electrolytes (MOILEs) was investigated by conducting galvanostatic charge/discharge and ionic conductivity experiments. The mixed electrolyte is based on the ionic liquid (IL) (EMI/TFSI/LiTFSI) and organic solvents EC/DMC (1:1 v/v). The effect of electrolyte type on the electrochemical performance of a LiCoO₂ cathode and a SnO₂/C composite anode in lithium anode (or cathode) half-cells was also investigated. The results demonstrated that the addition of 5 wt.% succinonitrile (SN) resulted in enhanced ionic conductivity of a 60% EMI-TFSI 40% EC/DMC MOILE from ~14 mS·cm^-1 to ~26 mS·cm^-1 at room temperature. Additionally, at a temperature of 100 °C, an increase in ionic conductivity from ~38 to ~69 mS·cm^-1 was observed for the MOILE with 5 wt% SN. The improvement in the ionic conductivity is attributed to the high polarity of SN and its ability to dissolve various types of salts such as LiTFSI. The galvanostatic charge/discharge results showed that the LiCoO₂ cathode with the MOILE (without SN) exhibited a 39% specific capacity loss at the 50th cycle while the LiCoO₂ cathode in the MOILE with 5 wt.% SN showed a decrease in specific capacity of only 14%. The addition of 5 wt.% SN to the MOILE with a SnO₂/C composite-fiber anode resulted in improved cycling performance and rate capability of the SnO₂/C composite-membrane anode in lithium anode half-cells. Based on the results reported in this work, a new avenue and promising outcome for the future use of MOILEs with SN in lithium-ion batteries (LIBs) can be opened.

"Solvent-in-salt" systems for design of new materials in chemistry, biology and energy research

Inorganic and organic "solvent-in-salt" (SIS) systems have been known for decades but have attracted significant attention only recently. Molten salt hydrates/solvates have been successfully employed as non-flammable, benign electrolytes in rechargeable lithium-ion batteries leading to a revolution in battery development and design. SIS with organic components (for example, ionic liquids containing small amounts of water) demonstrate remarkable thermal stability and tunability, and present a class of admittedly safer electrolytes, in comparison with traditional organic solvents. Water molecules tend to form nano- and microstructures (droplets and channel networks) in ionic media impacting their heterogeneity. Such microscale domains can be employed as microreactors for chemical and enzymatic synthesis. In this review, we address known SIS systems and discuss their composition, structure, properties and dynamics. Special attention is paid to the current and potential applications of inorganic and organic SIS systems in energy research, chemistry and biochemistry. A separate section of this review is dedicated to experimental methods of SIS investigation, which is crucial for the development of this field.

Relaxation in a Prototype Ionic Liquid: Influence of Water on the Dynamics

The influence of water on the relaxation of a prototype ionic liquid (IL) C₈mimBF₄ is examined in the IL-rich regime combining quasi-elastic neutron scattering (QENS) and molecular dynamics (MD) simulations. The QENS and MD simulations results for relaxation of IL and the equimolar mixture with water probed by the dynamics of the C₈mim hydrogen atoms in the time range of 2 ps to 1 ns are in excellent agreement. The QENS data show that translational relaxation increases by a factor of 7 on the addition of water, while rotational relaxation involving multiple processes fitted by a KWW function with low β values is speeded up by a factor of 3 on the time scale of QENS measurements. The MD simulations show that the cation diffusion coefficient, inverse viscosity, and ionic conductivity increase on the addition of water, consistent with the very small change in ionicity. The difficulties in obtaining rotational and translational diffusion coefficients from fits to QENS experiments of pure ILs and IL-water mixtures are discussed.

A comparative study of room temperature ionic liquids and their organic solvent mixtures near charged electrodes

The structural properties of electrolytes consisting of solutions of ionic liquids in a polar solvent at charged electrode surfaces are investigated using classical atomistic simulations. The studied electrolytes consisted of tetraethylammonium tetrafluoroborate (NEt4-BF4), 1-ethyl-3-methylimidazolium tetrafluoroborate (c2mim-BF4) and 1-octyl-3-methylimidazolium tetrafluoroborate (c8mim-BF4) salts dissolved in acetonitrile solvent. We discuss the influence of electrolyte concentration, chemical structure of the ionic salt, temperature, conducting versus semiconducting nature of the electrode, electrode geometry and surface roughness on the electric double layer structure and capacitance and compare these properties with those obtained for pure room temperature ionic liquids. We show that electrolytes consisting of solutions of ions can behave quite differently from pure ionic liquid electrolytes.

Ion Transport Mechanism of a Gel Electrolyte Comprising a Salt in Binary Plastic Crystalline Mixtures Confined inside a Polymer Network

We discuss here the ion transport mechanism of a gel electrolyte comprising lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) solvated by two plastic crystalline solvents, one a solid (succinonitrile, abbreviated as SN) and another (a room temperature ionic liquid) (1-butyl-1-methylpyrrolidinium bis(trifluoromethanesulfonyl)imide, (abbreviated as IL) confined inside a linear network of poly(methyl methacrylate) (PMMA). The concentration of the IL component (x) determines the physical properties of the unconfined electrolyte (i.e., SN_1-xIL_x-LiTFSI) and when confined inside the polymer network (GPE-x). The extent of disorder in the SN_1-xIL_x-LiTFSI and the GPE-x electrolytes is enhanced compared to both the bare SN-LiTFSI and IL-LiTFSI electrolytes. The enhanced disordering in the plastic phase alters both the local ion environment and viscosity. These changes strongly influence the ion mobility and nature of predominant charge carriers and thus the ion conduction mechanism in SN_1-xIL_x-LiTFSI and GPE-x. The proposed SN_1-xIL_x-LiTFSI and the GPE-x electrolytes show predominantly anion conduction (t_TFSI ≈ 0.5); however, lithium transference number (t_Li ≈ 0.2) is nearly an order higher than the IL-LiTFSI (t_Li ≈ 0.02-0.06). The ionic conductivity of SN_1-xIL_x-LiTFSI is much higher (especially for x ≈ 0.1) compared to both SN-LiTFSI and IL-LiTFSI. The ionic conductivity of the GPE-x, though lower than the unconfined SN_1-xIL_x-LiTFSI electrolytes, is still very promising, displaying values of ∼10^-3 Ω^-1 cm^-1. The GPE-x displayed compliable mechanical properties, stable Li-electrode/electrolyte interface, low rate of Al corrosion, and stable cyclability over several tens of charge-discharge cycles when assembled in a separator-free Li-graphite cell. The promising electrochemical performance further justifies the simple strategy of employing mixed physical state plasticizers to tune the physical properties of polymer electrolytes requisite for application in rechargeable batteries.

Effect of water on the structure of a prototype ionic liquid

The influence of water on the structure of a prototype ionic liquid (IL) 1-octyl-3-methylimidazolium tetrafluoroborate (C₈mimBF₄) is examined in the IL-rich regime using high-energy X-ray diffraction (HEXRD) and molecular dynamics (MD) simulations.

Decomposition of the fluoroethylene carbonate additive and the glue effect of lithium fluoride products for the solid electrolyte interphase: an ab initio study

Additives in the electrolyte solution of lithium-ion batteries (LIBs) have a large impact on the performance of the solid electrolyte interphase (SEI) that forms on the anode and is a key to the stability and durability of LIBs.

Anion-Tunable Properties and Electrochemical Performance of Functionalized Ferrocene Compounds

We report a series of ionically modified ferrocene compounds for hybrid lithium-organic non-aqueous redox flow batteries, based on the ferrocene/ferrocenium redox couple as the active catholyte material. Tetraalkylammonium ionic moieties were incorporated into the ferrocene structure, in order to enhance the solubility of the otherwise relatively insoluble ferrocene. The effect of various counter anions of the tetraalkylammonium ionized species appended to the ferrocene, such as bis(trifluoromethanesulfonyl)imide, hexafluorophosphate, perchlorate, tetrafluoroborate, and dicyanamide on the solubility of the ferrocene was investigated. The solution chemistry of the ferrocene species was studied, in order to understand the mechanism of solubility enhancement. Finally, the electrochemical performance of these ionized ferrocene species was evaluated and shown to have excellent cell efficiency and superior cycling stability.