Direct measurement of the binding force between microfabricated particles and a planar surface in aqueous solution by force-sensing piezoresistive cantilevers

Micro Water Flow Measurement Using a Temperature-Compensated MEMS Piezoresistive Cantilever

In this study, we propose a microelectromechanical system (MEMS) force sensor for microflow measurements. The sensor is equipped with a flow sensing piezoresistive cantilever and a dummy piezoresistive cantilever, which acts as a temperature reference. Since the dummy cantilever is also in the form of a thin cantilever, the temperature environment of the dummy sensor is almost identical to that of the sensing cantilever. The temperature compensation effect was measured, and the piezoresistive cantilever was combined with a gasket jig to enable the direct implementation of the piezoresistive cantilever in a flow tube. The sensor device stably measured flow rates from 20 μL/s to 400 μL/s in a silicon tube with a 2-mm inner diameter without being disturbed by temperature fluctuations.

Biocompatible Cantilevers for Mechanical Characterization of Zebrafish Embryos using Image Analysis

We have developed a force sensing system to continuously evaluate the mechanical elasticity of micrometer-scale (a few hundred micrometers to a millimeter) live tissues. The sensing is achieved by measuring the deflection of force sensitive cantilevers through microscopic image analysis, which does not require electrical strain gauges. Cantilevers made of biocompatible polydimethylsiloxane (PDMS) were actuated by a piezoelectric actuator and functioned as a pair of chopsticks to measure the stiffness of the specimen. The dimensions of the cantilevers were easily adjusted to match the size, range, and stiffness of the zebrafish samples. In this paper, we demonstrated the versatility of this technique by measuring the mechanical elasticity of zebrafish embryos at different stages of development. The stiffness of zebrafish embryos was measured once per hour for 9 h. From the experimental results, we successfully quantified the stiffness change of zebrafish embryos during embryonic development.

Tribochemistry and superlubricity induced by hydrogen ions

Friction behavior of aqueous solution at macroscale is quite different from that at nanoscale. At macroscale, tribochemistry usually occurs between lubricant and friction surfaces in the running-in process due to a high contact pressure, and most such processes can lead to friction reduction. In the present work, we reported that the hydrogen ions in aqueous solution played an important role in tribochemistry in running-in process (friction reducing process), which could result in the friction coefficient reducing from 0.4 to 0.04 between Si(3)N(4) and glass surfaces at macroscale. It is found that the running-in process and low friction state are closely dependent on the concentration of hydrogen ions in the contact region between the two friction surfaces. The lubrication mechanism is attributed to tribochemical reaction occurring between hydrogen ions and surfaces in the running-in process, which forms an electrical double layer and hydration layer to lower friction force. Finally, the running-in process of H(3)PO(4) (pH = 1.5) was investigated, which could realize superlubricity with an ultralow friction coefficient of about 0.004.

Template-assisted assembly of the functionalized cubic and spherical microparticles

The patterned template-assisted assembly of the cubic microparticles driven by the competing capillary, Columbic, and van der Waals forces had been studied in comparison with the traditional spherical colloidal microparticles. We observed that the spherical and cubic microparticles assembled with different probability in the channels of the hydrophobic-hydrophilic patterned substrates due to differences in a balance of adhesive and capillary forces. In contrast to highly selective assembly of spherical microparticles, selective deposition of cubic microcrystals with channels is impeded by strong adhesive forces facilitated by large specific interfacial areas between cube facets and substrate. The modification of the patterned substrate by functionalized coatings with oppositely charged topmost layers significantly increases the probability (to 86%) of the cubic microparticles to assemble into chemically modified channels. The introduction of ultrathin LbL shells on cubic microparticles and functionalization of patterned substrates are critical for the directed colloidal assembly of anisotropic microparticles into ordered aggregates.

Mechanical impulses can control metaphase progression in a mammalian cell

Chromosome segregation machinery is controlled by mechanochemical regulation. Tension in a mitotic spindle, which is balanced by molecular motors and polymerization-depolymerization dynamics of microtubules, is thought to be essential for determining the timing of chromosome segregation after the establishment of the kinetochore-microtubule attachments. It is not known, however, whether and how applied mechanical forces modulate the tension balance and chemically affect the molecular processes involved in chromosome segregation. Here we found that a mechanical impulse externally applied to mitotic HeLa cells alters the balance of forces within the mitotic spindle. We identified two distinct mitotic responses to the applied mechanical force that either facilitate or delay anaphase onset, depending on the direction of force and the extent of cell compression. An external mechanical impulse that physically increases tension within the mitotic spindle accelerates anaphase onset, and this is attributed to the facilitation of physical cleavage of sister chromatid cohesion. On the other hand, a decrease in tension activates the spindle assembly checkpoint, which impedes the degradation of mitotic proteins and delays the timing of chromosome segregation. Thus, the external mechanical force acts as a crucial regulator for metaphase progression, modulating the internal force balance and thereby triggering specific mechanochemical cellular reactions.

Probing the mechanical architecture of the vertebrate meiotic spindle

Accurate chromosome segregation during meiosis depends on the assembly of a microtubule-based spindle of proper shape and size. Current models for spindle-size control focus on reaction diffusion-based chemical regulation and balance in activities of motor proteins. Although several molecular perturbations have been used to test these models, controlled mechanical perturbations have not been possible. Here we report a piezoresistive dual cantilever-based system to test models for spindle-size control and examine the mechanical features, such as deformability and stiffness, of the vertebrate meiotic spindle. We found that meiotic spindles prepared in Xenopus laevis egg extracts were viscoelastic and recovered their original shape in response to small compression. Larger compression resulted in plastic deformation, but the spindle adapted to this change, establishing a stable mechanical architecture at different sizes. The technique we describe here may also be useful for examining the micromechanics of other cellular organelles.