Molecular surface structural changes of plasticized PVC materials after plasma treatment

Quantifying Chemical Reactions and Interfacial Properties at Buried Polymer/Polymer Interfaces

Maleic anhydride (MAH)-modified polymers are used as tie layers for binding dissimilar polymers in multilayer polymer films. The MAH chemistry which promotes adhesion is well characterized in the bulk; however, only recently has the interfacial chemistry been studied. Sum frequency generation vibrational spectroscopy (SFG) is an interfacial spectroscopy technique which provides detailed information on interfacial chemical reactions, species, and molecular orientations and has been essential for characterizing the MAH chemistry in both nylon and ethyl vinyl alcohol copolymer (EVOH) model systems and coextruded multilayer films. Here, we further characterize the interfacial chemistry between MAH-modified polyethylene tie layers and both EVOH and nylon by investigating the model systems over a range of MAH concentrations. We can detect the interfacial chemical reaction products between MAH and the barrier layer at MAH concentrations of ≥0.022 wt % for nylon and ≥0.077 wt % for EVOH. Additionally, from the concentration-dependent reaction reactant/product SFG peak positions and the product imide or ester/acid C═O group tilt angles extracted from the polarization-dependent SFG spectra, we quantitatively observe concentration-dependent changes to both the interfacial chemistry and interfacial structure. The interfacial chemistry and molecular orientation as a function of MAH concentration are well correlated with the adhesion strength, providing important quantitative information for the future design of MAH-modified tie layers for a variety of important applications.

Arc plasma for high-efficiency ionization and scavenging of plasticizers in wrap films

Herein, ambient electric arc ionization mass spectrometry was used to examine 16 plasticizers in various wrap films, demonstrating high sensitivity (detection limit: <0.2 ng/mg) and precision (intra-/inter-day precision: <12 %). The ease of operation helps in the identification of wrap film and plasticizer analysis. In addition, the introduction of a cold arc plasma treatment presents a practical and innovative method for effectively eliminating plasticizers. This innovative strategy has implications for both environmental protection and food safety.

Flotation separation of hazardous polyvinyl chloride towards source control of microplastics based on selective hydrophilization of plasticizer-doping surfaces

As the single largest chlorine source of plastics, hazardous polyvinyl chloride (PVC) has become an increasing environmental concern with the rapid microplastics accumulation. An advanced separation method is advocated to purify waste PVC plastics, optimize physical recycling, and protect aquatic and terrestrial environment safety. In this study, we proposed a novel scheme for the flotation separation of PVC plastics with diverse plasticizer contents (PVCs) via regulating hydrophilicity based on a selective ferric deposition. Rigid PVCs were prone to loading ferric ions and generating hydrophilic shells than flexible PVCs. Plasticizers can diffuse freely through the interior and surface of PVC plastics. Abundant plasticizers thereby overlaid the surface of flexible PVC and shielded PVC matrix from ferric ions. By regulating the ferric concentration, the wettability of PVCs was adjusted to separate rigid and flexible PVCs by froth flotation. Waste PVCs could also be separated from each other through the compound process of ferric deposition and flotation, further confirming its feasibility and stability. Thus far, this study supplies distinctive insights into the wettability regulation of plasticizer-doping PVC surfaces, contributes a pioneering hydrophilization method to PVCs separation and recycling, and mitigates hazardous PVC microplastics by source control.

Evaluation of characteristics and microbial community of anaerobic granular sludge under microplastics and aromatic carboxylic acids exposure

The influences of polyether sulfone (PES) microplastics and different structures aromatic carboxylic acids such as benzoic acid (BA), phthalic acid (PA), hemimellitic acid (HA), and 1-naphthoic acid (1-NA) on the performances and characteristics of anaerobic granular sludge as well as the microbial community were investigated. The chemical oxygen demand (COD) removal efficiency was the highest in the experimental group with 40 mg/L BA, reaching 90.1%. The inhibitory effect of aromatic carboxylic acids addition on the 2,3,5-triphenyltetrazolium chloride (TTC) activity was more obvious than that on 2-para (iodo-phenyl)-3(nitrophenyl)-5(phenyl) tetrazolium chloride (INT) activity. Compared with the control group (only 0.5 g/L PES microplastics, 60.6 mg TF·g TSS·h^-1), the inhibition effect of TTC activity was 32.5 mg TF·g TSS·h^-1 and 44.3 mg TF·g TSS·h^-1 in the 40 mg/L HA and 40 mg/L 1-NA experimental groups, respectively. When aromatic carboxylic acids were added, the activities of acetate kinase and coenzyme F₄₂₀ in the anaerobic granular sludge decreased. The excitation-emission matrix (EEM) fluorescence spectra indicated that loosely bound extracellular polymeric substances (LB-EPS) began to decay. After the addition of different aromatic carboxylic acids, the CC and CH functional groups of the anaerobic granular sludge increased, suggesting that aromatic carboxylic acids migrated to the surface of anaerobic granular sludge, such a transfer would lead to changes in anaerobic granular sludge performance. High-throughput sequencing technology showed that the dominant microbial communities in the anaerobic granular sludge were Proteobacteria, Methanothrix, and Methanomicrobia. After the addition of aromatic carboxylic acids, the relative abundances of Proteobacteria, Methanobacterium, and Methanospirillum increased. In the presence of PES, 1-NA had the most serious toxicity to the anaerobic granular sludge.

Sum Frequency Generation Vibrational Spectroscopy for Characterization of Buried Polymer Interfaces

Sum frequency generation vibrational spectroscopy (SFG-VS) has become one of the most appealing technologies to characterize molecular structures at interfaces. In this focal point review, we focus on SFG-VS studies at buried polymer interfaces and review many of the recent publications in the field. We also cover the essential theoretical background of SFG-VS and discuss the experimental implementation of SFG-VS.

Molecular adsorption at electrolyte/α-Al2O3 interface of aluminum electrolytic capacitor revealed by sum frequency vibrational spectroscopy

The operating voltage of an aluminum electrolytic capacitor is determined by the breakdown voltage (Ub) of the Al2O3 anode. Ub is related to the molecular adsorption at the Al2O3/electrolyte interface. Therefore, we have employed sum-frequency vibrational spectroscopy (SFVS) to study the adsorption states of a simple electrolyte, ethylene glycol (EG) solution with ammonium adipate, on an α-Al2O3 surface. In an acidic electrolyte (pH < 6), the Al2O3 surface is positively charged. The observed SFVS spectra show that long chain molecules poly ethylene glycol and ethylene glycol adipate adopt a "lying" orientation at the interface. In an alkaline electrolyte (pH > 8), the Al2O3 surface is negatively charged and the short chain EG molecules adopt a "tilting" orientation. The Ub results exhibit a much higher value at pH < 6 compared with that at pH > 8. Since the "lying" long chain molecules cover and protect the Al2O3 surface, Ub increases with a decrease of pH. These findings provide new insights to study the breakdown mechanisms and to develop new electrolytes for high operating voltage capacitors.

Molecular interactions of organic molecules at the air/water interface investigated by sum frequency generation vibrational spectroscopy

The molecular structure and dynamics of organic molecules at the aqueous interface have attracted a number of investigations owing to their importance and specific nature. However, there are relatively few studies on the direct characterization of the molecular interactions at the air/water interface because they are extremely difficult to measure in experiments. In this study, we use dibutyl ester molecules (R₁CO₂R₂O₂CR₁) as a model of organic molecules, and investigate their molecular structure and interactions using sum frequency generation vibrational spectroscopy. We demonstrate that the molecular interactions can be estimated by measuring the intensity ratio of the symmetric stretching (ν₁) and Fermi resonant bands (2ν₂) of methyl groups. Here, dibutyl ester molecules are widely used as plasticizers in polymers to improve the properties of the plastics and polymers. It is found that the orientation angles of the tailed methyl groups at the air/water interface decrease from 34° to 19° when the chain length of R₂ increases from 0 to 8. The total intermolecular interactions of the dibutyl ester molecules decrease as the chain length of R₂ increases because the van der Waals interactions between the hydrocarbon chains increase, while the hydrogen bond interactions between the carbonyl group and water molecules decrease. Our study demonstrates the stability of ester-based plasticizers in polymers can be well predicted from the intensity ratio of the ν₁ and 2ν₂ bands of methyl group. Such an intensity ratio can be thus used as an effective vibrational optical ruler for characterizing molecular interactions between plasticizers and polymers.

Nondestructive Quantification of Local Plasticizer Concentration in PVC by (1)H NMR Relaxometry

The properties of plasticized poly(vinyl chloride) (PVC) , one of the most important polymers today, are strongly dictated by the concentration of plasticizer. Yet, it has been impossible to quantify this concentration at different positions inside a PVC product without its destruction because of a lack of suitable analytical methods. Thus, this paper introduces a simple, fast, and efficient way to determine truly nondestructively the concentration of plasticizer in PVC by single-sided nuclear magnetic resonance (NMR). With the help of correlation curves between the concentration of plasticizer inside nonaged PVC samples and the corresponding volume-averaged NMR parameters, single-sided NMR allows the quantification of the local concentration of plasticizer in aged PVC plates at different depths by spatially resolved relaxation measurements. The presented approach represents a fundamental step toward in situ characterization of plasticized PVC.

Controlled drug release and hydrolysis mechanism of polymer-magnetic nanoparticle composite

Uniform and multifunctional poly(lactic acid) (PLA)-nanoparticle composite has enormous potential for applications in biomedical and materials science. A detailed understanding of the surface and interface chemistry of these composites is essential to design such materials with optimized function. Herein, we designed and investigated a simple PLA-magnetic nanoparticle composite system to elucidate the impact of nanoparticles on the degradation of polymer-nanoparticle composites. In order to have an in-depth understanding of the mechanisms of hydrolysis in PLA-nanoparticle composites, degradation processes were monitored by several surface sensitive techniques, including scanning electron microscopy, contact angle goniometry, atomic force microscopy, and sum frequency generation spectroscopy. As a second-order nonlinear optical technique, SFG spectroscopy was introduced to directly probe in situ chemical nature at the PLA-magnetic nanoparticle composite/aqueous interface, which allowed for the delineation of molecular mechanisms of various hydrolysis processes for degradation at the molecular level. The best PLA-NP material, with a concentration of 20% MNP in the composite, was found to enhance the drug release rate greater than 200 times while maintaining excellent controlled drug release characteristics. It was also found that during hydrolysis, various crystalline-like PLA domains on the surfaces of PLA-nanoparticle composites influenced various hydrolysis behaviors of PLA. Results from this study provide new insight into the design of nanomaterials with controlled degradation and drug release properties, and the underlined molecular mechanisms. The methodology developed in this study to characterize the polymer-nanoparticle composites is general and widely applicable.

Probing the molecular structures of plasma-damaged and surface-repaired low-k dielectrics

A comprehensive characterization on the plasma-damaged and silylation-repaired low-k dielectrics was demonstrated here at the molecular level.

The molecular interfacial structure and plasticizer migration behavior of “green” plasticized poly(vinyl chloride)

Both oxygen and argon plasma treatment made TBAC–PVC surfaces hydrophilic, but that of argon enhanced the migration of TBAC to water.

In situ observation of water behavior at the surface and buried interface of a low-k dielectric film

Water adsorption in porous low-k dielectrics has become a significant challenge for both back-end-of-line integration and reliability. A simple method is proposed here to achieve in situ observation of water structure and water-induced structure changes at the poly(methyl silsesquioxane) (PMSQ) surface and the PMSQ/solid buried interface at the molecular level by combining sum frequency generation (SFG) vibrational spectroscopic and Fourier transform infrared (FTIR) spectroscopic studies. First, in situ SFG investigations of water uptake were performed to provide direct evidence that water diffuses predominantly along the PMSQ/solid interface rather than through the bulk. Furthermore, SFG experiments were conducted at the PMSQ/water interface to simulate water behavior at the pore inner surfaces for porous low-k materials. Water molecules were found to form strong hydrogen bonds at the PMSQ surface, while weak hydrogen bonding was observed in the bulk. However, both strongly and weakly hydrogen bonded water components were detected at the PMSQ/SiO2 buried interface. This suggests that the water structures at PMSQ/solid buried interfaces are also affected by the nature of solid substrate. Moreover, the orientation of the Si-CH3 groups at the buried interface was permanently changed by water adsorption, which might due to low flexibility of Si-CH3 groups at the buried interface. In brief, this study provides direct evidence that water molecules tend to strongly bond (chemisorbed) with low-k dielectric at pore inner surfaces and at the low-k/solid interface of porous low-k dielectrics. Therefore, water components at the surfaces, rather than the bulk, are likely more responsible for chemisorbed water related degradation of the interconnection layer. Although the method developed here was based on a model system study, we believe it should be applicable to a wide variety of low-k materials.

Observing phthalate leaching from plasticized polymer films at the molecular level

Phthalates, the most widely used plasticizers in poly(vinyl chloride) (PVC), have been extensively studied. In this paper, a highly sensitive, easy, and effective method was developed to examine short-term phthalate leaching from PVC/phthalate films at the molecular level using sum frequency generation vibrational spectroscopy (SFG). Combining SFG and Fourier transform infrared spectroscopy (FTIR), surface and bulk molecular structures of PVC/phthalate films were also comprehensively evaluated during the phthalate leaching process under various environments. The leaching processes of two phthalates, diethyl phthalate (DEP) and dibutyl phthalate (DBP), from the PVC/phthalate films with various weight ratios were studied. Oxygen plasma was applied to treat the PVC/phthalate film surfaces to verify its efficacy on preventing/reducing phthalate leaching from PVC. Our results show that DBP is more stable than DEP in PVC/phthalate films. Even so, DBP molecules were still found to very slowly leach to the environment from PVC at 30 °C, at a rate much slower than DEP. Also, the bulk DBP content substantially influences the DBP leaching. Higher DBP bulk concentration yields less stable DBP molecules in the PVC matrix, allowing molecules to leach from the polymer film more easily. Additionally, DBP leaching is very sensitive to temperature changes; higher temperature can strongly enhance the leaching process. For most cases, the oxygen plasma treatment can effectively prevent phthalate leaching from PVC films (e.g., for samples with low bulk concentrations of DBP-5 and 30 wt %). It is also capable of reducing phthalate leaching from high DBP bulk concentration PVC samples (e.g., 70 wt % DBP in PVC/DBP mixture). This research develops a highly sensitive method to detect chemicals at the molecular level as well as provides surface and bulk molecular structural changes. The method developed here is general and can be applied to detect small amounts of chemical/biological environmental contaminants.

Interfacial molecular restructuring of plasticized polymers in water

We present a means to study the molecular changes of the top and bottom of polymers contacted to water simultaneously in situ. Plasticizers were found to transfer from polymer surfaces to water in minutes.