Inverted microcontact printing on polystyrene-block-poly(tert-butyl acrylate) films: a versatile approach to fabricate structured biointerfaces across the length scales

The influence of anisotropic nano- to micro-topography on in vitro and in vivo osteogenesis

AIM

Topographically modified substrates are increasingly used in tissue engineering to enhance biomimicry. The overarching hypothesis is that topographical cues will control cellular response at the cell-substrate interface.

MATERIALS & METHODS

The influence of anisotropically ordered poly(lactic-co-glycolic acid) substrates (constant groove width of ~1860 nm; constant line width of ~2220 nm; variable groove depth of ~35, 306 and 2046 nm) on in vitro and in vivo osteogenesis were assessed.

RESULTS & DISCUSSION

We demonstrate that substrates with groove depths of approximately 306 and 2046 nm promote osteoblast alignment parallel to underlined topography in vitro. However, none of the topographies assessed promoted directional osteogenesis in vivo.

CONCLUSION

2D imprinting technologies are useful tools for in vitro cell phenotype maintenance.

Surface engineering of synthetic polymer materials for tissue engineering and regenerative medicine applications

When using polymer materials as scaffolds for tissue engineering or regenerative medicine applications the initial, and often lasting, interaction between cells and the material areviasurfaces.

Simultaneous biochemical and topographical patterning on curved surfaces using biocompatible sacrificial molds

A method for the simultaneous (bio)chemical and topographical patterning of enclosed structures in poly(dimethyl siloxane) (PDMS) is presented. The simultaneous chemical and topography transference uses a water-soluble chitosan sacrificial mold to impart a predefined pattern with micrometric accuracy to a PDMS replica. The method is compared to conventional soft-lithography techniques on planar surfaces. Its functionality is demonstrated by the transference of streptavidin directly to the surface of the three-dimensional PDMS structures as well as indirectly using streptavidin-loaded latex nanoparticles. The streptavidin immobilized on the PDMS is tested for bioactivity by coupling with fluorescently labeled biotin. This proves that the streptavidin is immobilized on the PDMS surface, not in the bulk of the polymer, and is therefore accessible for use as signaling/binding element in micro and bioengineering. The use of a biocompatible polymer and processes enables the technique to be used for the chemical patterning of tissue constructions.

Improving protein transfer efficiency and selectivity in affinity contact printing by using UV-modified surfaces

Affinity contact printing (αCP) is a technique that allows the selective capture of a target protein from solutions to a polymeric stamp decorated with an antibody, and then the target protein is printed onto a solid surface. The success of αCP critically relies on the precise control of protein-surface interactions. Here, we report a study on the effect of UV on the protein-surface interactions between protein and polydimethylsiloxane stamps and between protein and glass slides decorated with N,N-dimethyl-n-octadecyl-3-aminopropyltrimethoxysilyl chloride (DMOAP). Our results show that UV-modified surfaces can be used to improve the transfer efficiency and selectivity of proteins during αCP. For example, the protein transfer efficiency of human IgG onto a DMOAP-coated slide increases from 7.2% to 45.1% after the UV treatment. On the basis of these results, UV-modified surfaces were employed to develop a αCP system for protein detection. The detection limit of anti-IgG in this system is around 10 ng/mL, and the dynamic range is 4 orders of magnitude.

Fabrication and selective functionalization of amine-reactive polymer multilayers on topographically patterned microwell cell culture arrays

We report an approach to the fabrication and selective functionalization of amine-reactive polymer multilayers on the surfaces of 3-D polyurethane-based microwell cell culture arrays. "Reactive" layer-by-layer assembly of multilayers using branched polyethyleneimine (BPEI) and the azlactone-functionalized polymer poly(2-vinyl-4,4'-dimethylazlactone) (PVDMA) yielded film-coated microwell arrays that could be chemically functionalized postfabrication by treatment with different amine-functionalized macromolecules or small molecule primary amines. Treatment of film-coated arrays with the small molecule amine d-glucamine resulted in microwell surfaces that resisted the adhesion and proliferation of mammalian fibroblast cells in vitro. These and other experiments demonstrated that it was possible to functionalize different structural features of these arrays in a spatially resolved manner to create dual-functionalized substrates (e.g., to create arrays having either (i) azlactone-functionalized wells, with regions between the wells functionalized with glucamine or (ii) substrates with spatially resolved regions of two different cationic polymers). In particular, spatial control over glucamine functionalization yielded 3-D substrates that could be used to confine cell attachment and growth to microwells for periods of up to 28 days and support the 3-D culture of arrays of cuboidal cell clusters. These approaches to dual functionalization could prove useful for the long-term culture and maintenance of cell types for which the presentation of specific and chemically well-defined 3-D culture environments is required for control over cell growth, differentiation, and other important behaviors. More generally, our approach provides methods for the straightforward chemical functionalization of otherwise unreactive topographically patterned substrates that could prove to be useful in a range of other fundamental and applied contexts.

Nanoimprinted thin films of reactive, azlactone-containing polymers: combining methods for the topographic patterning of cell substrates with opportunities for facile post-fabrication chemical functionalization

Approaches to the fabrication of surfaces that combine methods for the topographic patterning of soft materials with opportunities for facile, post-fabrication chemical functionalization could contribute significantly to advances in biotechnology and a broad range of other areas. Here, we report methods that can be used to introduce well-defined nano- and microscale topographic features to thin films of reactive polymers containing azlactone functionality using nanoimprint lithography (NIL). We demonstrate that NIL can be used to imprint topographic patterns into thin films of poly(2-vinyl-4,4-dimethylazlactone) and a copolymer of methyl methacrylate and 2-vinyl-4,4-dimethylazlactone using silicon masters having patterns of grooves and ridges ranging in width from 400 nm to 2 microm, demonstrating the potential of this method to transfer patterns to films of these reactive polymers over a range of feature sizes and densities. We demonstrate further that the azlactone functionality of these polymers survives temperatures and pressures associated with NIL, and that topographically patterned films can be readily functionalized post-fabrication by treatment of surface-accessible azlactone functionality with small molecules and polymers containing primary amines. The results of experiments in which NIH-3T3 cells were seeded onto films imprinted with lined patterns having a pitch of 4 microm demonstrated that cells attach and proliferate on these azlactone-containing films and that they align in the direction of the imprinted pattern. Finally, we demonstrate that the treatment of these materials with amine-functionalized poly(ethylene glycol) (PEG) can be used to create regions of topographically patterned films that prevent cell adhesion. The results of this study suggest approaches to the functionalization of topographically patterned surfaces with a broad range of chemical functionality (e.g., peptides, proteins, carbohydrates, etc.) of biotechnological interest. The ability to manipulate and define both the physical topography and chemical functionality of these reactive materials could provide opportunities to investigate the combined effects of substrate topography and chemical functionality on cell behavior and may also be useful in a broad range of other applications.

Stamps, inks and substrates: polymers in microcontact printing

It's all about polymers! Polymers play a key role in the patterning and functionalization of surfaces by microcontact printing. Polymers are versatile stamps, inks and substrates and microcontact printing can provide microstructured polymer surfaces in a single printing step.