Properties of poly(styrene/alpha-tert-butoxy-omega-vinylbenzyl-polyglycidol) microspheres suspended in water. Effect of sodium chloride and temperature on particle diameters and electrophoretic mobility

Preparation of well-defined poly(2-hydroxyethyl methacrylate) macromonomers via atom transfer radical polymerization

A series of six near-monodisperse methacrylic macromonomers is prepared via atom transfer radical polymerization (ATRP) of 2-hydroxyethyl methacrylate using a tertiary amine-functionalized initiator at 50 °C, followed by quaternization with excess 4-vinylbenzyl chloride at 20 °C. GPC analyses indicate polydispersities of around 1.20 and their mean degrees of polymerization (DP) range from 20 to 70, as judged by both (1) H NMR and UV spectroscopy. The former technique is more convenient but the latter proved more accurate for the higher DP values, provided that an appropriate model compound is utilized for calibration. Finally, these new macromonomers are used to prepare sterically stabilized polystyrene latexes with relatively narrow size distributions via alcoholic dispersion polymerization.

Design of polyglycidol-containing microspheres for biomedical applications

The paper presents a short review on the synthesis, characterisation and selected medical applications of poly(styrene/α-tert-butoxy-ω-vinylbenzyl-polyglycidol) (P(S/PGL)) microspheres. The soap-free emulsion-polymerisation of styrene and α-tert-butoxy-ω-vinylbenzyl-polyglycidol macromonomer (PGL) in water yielded core-shell microspheres with a low particle-diameter dispersity (ratio of the weight average particle diameter and the number average particle diameter). The interfacial fraction of PGL units, estimated by XPS, was in the range of 0–42 mole % depending on the concentration of the macromonomer in the polymerisation feed. The studies of adsorption of model proteins showed that the surface fraction of adsorbed protein was significantly reduced when the PGL interfacial fraction was higher than 40 mole %. The P(S/PGL) particles with covalently immobilised proteins were used for the preparation of photonic crystal assemblies suitable for applications in optical biosensors and the medical diagnostic test for the detection of Helicobacter pylori antibodies in the blood serum.

Preparation and optical properties of novel bioactive photonic crystals obtained from core-shell poly(styrene/α-tert-butoxy-ω-vinylbenzyl-polyglycidol) microspheres

Optical properties of polymer microspheres with polystyrene cores and polyglycidol-enriched shells poly(styrene/α-tert-butoxy-ω-vinylbenzyl-polyglycidol) (P(S/PGL) particles with number average diameters D_n determined by scanning electron microscopy equal 237 and 271 nm), were studied before and after immobilization of ovalbumin. The particles were synthesized by emulsifier-free emulsion copolymerization of styrene and polyglycidol macromonomer (poly(styrene/α-tert-butoxy-ω-vinylbenzyl-polyglycidol)) initiated with potassium persulfate. Molar fraction of polyglycidol units in the interfacial layer of the microspheres determined by XPS was equal 42.6 and 34.0%, for the particles with D_n equal 137 and 271 nm, respectively. Colloidal crystals from the aforementioned particles were prepared by deposition of particle suspensions on the glass slides and subsequent evaporation of water. It was found that optical properties of colloidal crystals from the P(S/PGL) microspheres strongly depend on modification of their interfacial layer by covalent immobilization of ovalbumin. The coating of particles with ovalbumin resulted in decreasing their refractive index from 1.58 to 1.52.

Thermoresponsive colloidal crystals built from core-shell poly(styrene/alpha-tert-butoxy-omega-vinylbenzylpolyglycidol) microspheres

Core-shell particles of poly(styrene/alpha-tert-butoxy-omega-vinylbenzylpolyglycidol) P(S/PGL) were used as new building blocks for the assembly of a colloidal crystal. The added-value properties of these particles for photonic crystal architectures are their high hydrophilicity together with their thermoresponsivity. Indeed, the poglycidol-rich shell undergoes a phase transition above 45 degrees C, which leads to its collapse at the particle surface accompanied by a decrease in the particle diameter. The three-dimensional crystalline arrays display Bragg diffraction properties, as judged by angle-resolved reflectance spectroscopy. The thermoresponsivity of the colloidal assemblies was observed through modifications of their optical properties with respect to the temperature used during the assembly process. The wetting properties of the crystalline material were also shown to reversibly switch from hydrophilic to hydrophobic as a function of the assembly temperature, thus evidencing the reorganization of the surface polyglycidol chains during the polymer phase transition. This work shows conclusively that P(S/PGL) particles are promising alternatives to poly(N-isopropylacrylamide) and poly(ethylene glycol) particles for the elaboration of thermoresponsive colloidal crystals, with a phase transition situated in between those of these two polymers.