Ultrathin and stable active layer of dense composite membrane enabled by poly(dopamine)

Improved Electrical Output Performance of Cellulose-Based Triboelectric Nanogenerators Enabled by Negative Triboelectric Materials

Cellulose-based triboelectric nanogenerators (TENGs) have attracted widespread attention due to the low cost and environmentally friendly characteristics of cellulose. However, achieving high electrical energy output from these generators still presents significant challenges. Here, cellulose is dissolved-regenerated to form a composite aerogel with high specific surface area, in which cellulose-based composites with excellent negative triboelectric properties are developed by coupling the rich 3D network structure of the regenerated cellulose aerogel, modified barium titanate, and poly(vinylidene fluoride). The TENGs assembled from the composite materials exhibit an output voltage of 1040 V and a current of 1.165 mA at an external force of 8 N and a frequency of 4 Hz, outperforming all cellulose-based negative triboelectric materials. In addition, the nanogenerators have a stable electrical energy output capacity, with no significant property degradation in 100 000 contact-separation tests. The excellent electrical output property of the composite materials enables them to harvest energy from human movement and waterdrops, demonstrating their great application prospects in wearable devices, energy harvesting devices, self-powered sensors, and other fields.

Pulmonary decellularized extracellular matrix (dECM) modified polyethylene terephthalate three-dimensional cell carriers regulate the proliferation and paracrine activity of mesenchymal stem cells

Introduction: Mesenchymal stem cells (MSCs) possess a high degree of self-renewal capacity and in vitro multi-lineage differentiation potential. Decellularized materials have garnered considerable attention due to their elevated biocompatibility, reduced immunogenicity, excellent biodegradability, and the ability to partially mimic the in vivo microenvironment conducive to cell growth. To address the issue of mesenchymal stem cells losing their stem cell characteristics during two-dimensional (2D) cultivation, this study established three-dimensional cell carriers modified with lung decellularized extracellular matrix and assessed its impact on the life activities of mesenchymal stem cells. Methods: This study employed PET as a substrate material, grafting with polydopamine (PDA), and constructing a decellularized extracellular matrix (dECM) coating on its surface, thus creating the PET/PDA/dECM three-dimensional (3D) composite carrier. Subsequently, material characterization of the cellular carriers was conducted, followed by co-culturing with human umbilical cord mesenchymal stem cells in vitro, aiming to investigate the material's impact on the proliferation and paracrine activity of mesenchymal stem cells. Results and Discussion: Material characterization demonstrated successful grafting of PDA and dECM materials, and it had complete hydrophilicity, high porosity, and excellent mechanical properties. The material was rich in various ECM proteins (collagen I, collagen IV , laminin, fibronectin, elastin), indicating good biocompatibility. In long-term in vitro cultivation (14 days) experiments, the PET/PDA/dECM three-dimensional composite carrier significantly enhanced adhesion and proliferation of human umbilical cord-derived mesenchymal stem cells (HUCMSCs), with a proliferation rate 1.9 times higher than that of cells cultured on tissue culture polystyrene (TCPS) at day 14. Furthermore, it effectively maintained the stem cell characteristics, expressing specific antigens for HUCMSCs. Through qPCR, Western blot, and ELISA experiments, the composite carrier markedly promoted the expression and secretion of key cell factors in HUCMSCs. These results demonstrate that the PET/PDA/dECM composite carrier holds great potential for scaling up MSCs' long-term in vitro cultivation and the production of paracrine factors.

The effects of process parameters on polydopamine coatings employed in tissue engineering applications

The biomaterials’ success within the tissue engineering field is hinged on the capability to regulate tissue and cell responses, comprising cellular adhesion, as well as repair and immune processes’ induction. In an attempt to enhance and fulfill these biomaterials’ functions, scholars have been inspired by nature; in this regard, surface modification via coating the biomaterials with polydopamine is one of the most successful inspirations endowing the biomaterials with surface adhesive properties. By employing this approach, favorable results have been achieved in various tissue engineering-related experiments, a significant one of which is the more rapid cellular growth observed on the polydopamine-coated substrates compared to the untreated ones; nonetheless, some considerations regarding polydopamine-coated surfaces should be taken into account to control the ultimate outcomes. In this mini-review, the importance of coatings in the tissue engineering field, the different types of surfaces requiring coatings, the significance of polydopamine coatings, critical factors affecting the result of the coating procedure, and recent investigations concerning applications of polydopamine-coated biomaterials in tissue engineering are thoroughly discussed.

Ultrathin Membranes for Separations: A New Era Driven by Advanced Nanotechnology

Ultrathin membranes are at the forefront of membrane research, offering great opportunities in revolutionizing separations with ultrafast transport. Driven by advanced nanomaterials and manufacturing technology, tremendous progresses are made over the last 15 years in the fabrications and applications of sub-50 nm membranes. Here, an overview of state-of-the-art ultrathin membranes is first introduced, followed by a summary of the fabrication techniques with an emphasis on how to realize such extremely low thickness. Then, different types of ultrathin membranes, categorized based on their structures, that is, network, laminar, or framework structures, are discussed with a focus on the interplays among structure, fabrication methods, and separation performances. Recent research and development trends are highlighted. Meanwhile, the performances and applications of current ultrathin membranes for representative separations (gas separation and liquid separation) are thoroughly analyzed and compared. Last, the challenges in material design, structure construction, and coordination are given, in order to fully realize the potential of ultrathin membranes and facilitate the translation from scientific achievements to industrial productions.

Surface modification of nanofiltration membranes to improve the removal of organic micropollutants: Linking membrane characteristics to solute transmission

Surface modification of nanofiltration (NF) membranes has great potential to improve the removal of organic micropollutants (OMs) by NF membranes. This study used polydopamine (PDA) as a model coating to comprehensively link the changes in membrane properties with the changes in transmission of 34 OMs. The membrane characterization demonstrated that a thicker, denser, and more hydrophilic PDA coating can be achieved by increasing the PDA deposition time from 0.5 to 4 hours. Overall, the transmissions of target OMs were reduced by PDA-coated NF membranes compared to unmodified NF membranes. The neutral hydrophobic compounds showed lower transmissions for longer PDA coating (PDA4), while the neutral hydrophilic compounds tended to show lower transmissions for shorter PDA coating (PDA0.5). To explain this, competing effects provided by the PDA coatings are proposed including sealing defects, inducing cake-enhanced concentration polarization in the coating layer for neutral hydrophilic compounds, and weakened hydrophobic adsorption for neutral hydrophobic compounds. For charged compounds, PDA4 with the greatest negative charge among the PDA-coated membranes showed the lowest transmission. Depending on the molecular size and hydrophilicity of the compounds, the transmission of OMs by the PDA4 coating could be reduced by 70% with only a 26.4% decline in water permeance. The correlations and mechanistic insights provided by this work are highly useful for designing membranes with specific surface properties via surface modification to improve the removal of OMs without compromising water production.

Understanding the self-polymerization mechanism of dopamine by molecular simulation and applying dopamine surface modification to improve the interfacial adhesion of polyimide fibers with epoxy resin matrix

The object of this paper is to interpret the self-polymerization mechanism of dopamine by molecular simulation and use dopamine polymerization to modify the surface properties of polyimide fibers for improving its interfacial adhesion strength with the epoxy resin matrix. Theoretically, the molecular simulation results of calculated energy band gaps and infrared spectrum of the intermediate products generated in the dopamine self-polymerization process confirmed that the spontaneity of self-polymerization of dopamine and the occurrence of intramolecular cyclization and intermolecular polymerization in the self-polymerization process of dopamine. Moreover, the interaction between polyimide and poly(dopamine) was simulated, and the calculated results showed that the interaction between them depended on hydrogen bonding and was verified by ultrasound treatment. Experimentally, the effect of dopamine treatment concentration on the surface properties of polyimide fibers was investigated. Obviously, after a relatively high dopamine concentration treatment, the surface roughness and surface energy of polyimide fibers were largely improved and the number of active groups on polyimide fibers surface were increased, which were altogether conducive to enhance the adhesion strength of polyimide fibers with the epoxy resin matrix.

One-Pot Polymerization of Dopamine as an Additive to Enhance Permeability and Antifouling Properties of Polyethersulfone Membrane

This paper reports the fabrication of polyethersulfone membranes via in situ hydrogen peroxide-assisted polymerization of dopamine. The dopamine and hydrogen peroxide were introduced into the dope solution where the polymerization occurred, resulting in a single-step additive formation during membrane fabrication. The effectivity of modification was evaluated through characterizations of the resulting membranes in terms of chemical functional groups, surface morphology, porosity, contact angle, mechanical strength and filtration of humic acid solution. The results confirm that the polydopamine was formed during the dope solution mixing through peroxide-assisted polymerization as proven by the appearance of peaks associated OH and NH groups in the resulting membranes. The presence of polydopamine residual in the membrane matric enhances the pore properties in terms of size and porosity (by a factor of 10), and by lowering the hydrophilicity (from 69° to 53°) which leads to enhanced filtration flux of up to 217 L/m2 h. The presence of the residual polydopamine also enhances membrane surface hydrophilicity which improve the antifouling properties as shown from the flux recovery ratio of > 80%.

Alleviating membrane fouling of modified polysulfone membrane via coagulation pretreatment/ultrafiltration hybrid process

In this study, ultrafiltration membrane fouling was alleviated by hydrophilic modification and coagulation pretreatment. A polydopamine (PDA) layer was used as a bridge to introduce the nano titanium dioxide (TiO₂) onto the polysulfone (PSf) membranes, forming a hydrophilic modified layer. A relationship model was established between the coagulation efficiencies and floc properties and membrane fouling of the modified PSf membranes during the coagulation/ultrafiltration (C-UF) process. The combination styles of flocculants, poly dimethyldiallylammonium chloride (PDMDAAC) and polyaluminum chloride (PAC) were used in C-UF hybrid process. The characterization results indicated that the hydrophilicity was significantly enhanced in the modified PSf membranes. Scanning electron microscopy (SEM) tests proved that the PDA layer could be tightly bound to TiO₂ by coordination bond onto PSf membrane surface. In the acidic conditions, more TiO₂ nano-particles were adhered on the PDA particles surface as the pH of (NH₄)₂TiF₆ solution was increased, which resulted in higher hydrophilicity of membranes. In addition, the C-UF tests exhibited that the coagulation efficiency was greatly improved in the PAC/PDMDAAC system, and the PSf membrane modified by PDA/TiO₂ in UF tests significantly reduced the membrane fouling, this was partially due to the formation of TiO₂ modified coating with higher hydrophilicity.

Solution Blown Nylon 6 Nanofibrous Membrane as Scaffold for Nanofiltration

In this work, a nylon 6 nanofibrous membrane was prepared via solution blowing technology and followed hot-press as scaffold for nanofiltration. The structure and properties of the hot-pressed nylon 6 nanofibrous membrane (HNM) were studied the effect of hot-pressing parameters and areal densities. Then an ultra-thin polyamide (PA) active layer was prepared by interfacial polymerization on HNM. The effects of nanofibrous scaffolds on the surface properties of ultra-thin nanofiltration membranes and their filtration performance were studied. Results showed that the nylon 6 nanofibers prepared at a concentration of 15 wt % had a good morphology and diameter distribution and the nanofibers were stacked more tightly and significantly reduced in diameter after hot pressing at 180 °C under the pressure of 15 MPa for 10 s. When the porous scaffold was prepared, HNM with an areal density of 9.4 and 14.1 g/m² has a better apparent structure, a smaller pore size, a higher porosity and a greater strength. At the same time, different areal densities of HNM have an important influence on the preparation and properties of nanofiltration membranes. With the increase of areal density, the uniformity of HNM increased while their surface roughness and pore size decreased, which is beneficial to the establishment of PA barrier layer. With areal density of 9.4 and 14.1 g/m², the as-prepared nanofiltration membrane has a smoother surface and more outstanding filtration performance. The pure water flux is 13.1 L m⁻² h⁻¹ and the filtration efficiencies for NaCl and Na₂SO₄ are 81.3% and 85.1%, respectively.

Dopamine Incorporated Forward Osmosis Membranes with High Structural Stability and Chlorine Resistance

The degradation and detachment of the polyamide (PA) layer for the conventional thin-film composite (TFC) membranes due to chemical disinfectants cleaning with chlorine and material difference of PA layer and substrate are two major bottlenecks of forward osmosis (FO) technology. In this study, a new type of FO membranes was first prepared by controlling dopamine (DA) as the sole amine in the aqueous phase and the reaction with trimesoyl chloride (TMC) as the acyl chloride during interfacial polymerization (IP) process. The influence of membrane synthesis parameters such as monomer concentration, pH of the aqueous phase, IP reaction time and IP temperature were systematically investigated. The optimized membrane showed both improved structure stability and chlorine resistance, more so than the conventional TFC membrane. In general, novel DA/TMC TFC membranes could be an effective strategy to synthesize high-performance FO membranes with excellent structural stability and chlorine resistance.

Electrospun Silk Fibroin Nanofibrous Scaffolds with Two-Stage Hydroxyapatite Functionalization for Enhancing the Osteogenic Differentiation of Human Adipose-Derived Mesenchymal Stem Cells

The development of functional scaffolds with improved osteogenic potential is important for successful bone formation and mineralization in bone tissue engineering. In this study, we developed a functional electrospun silk fibroin (SF) nanofibrous scaffold functionalized with two-stage hydroxyapatite (HAp) particles, using mussel adhesive-inspired polydopamine (PDA) chemistry. HAp particles were first incorporated into SF scaffolds during the electrospinning process, and then immobilized onto the electrospun SF nanofibrous scaffolds containing HAp via PDA-mediated adhesive chemistry. We obtained two-stage HAp-functionalized SF nanofibrous scaffolds with improved mechanical properties and capable of providing a bone-specific physiological microenvironment. The developed scaffolds were tested for their ability to enhance the osteogenic differentiation of human adipose-derived mesenchymal stem cells (hADMSCs) in vitro and repair bone defect in vivo. To boost their ability for bone repair, we genetically modified hADMSCs with the transcriptional coactivator with PDZ-binding motif (TAZ) via polymer nanoparticle-mediated gene delivery. TAZ is a well-known transcriptional modulator that activates the osteogenic differentiation of mesenchymal stem cells (MSCs). Two-stage HAp-functionalized SF scaffolds significantly promoted the osteogenic differentiation of TAZ-transfected hADMSCs in vitro and enhanced mineralized bone formation in a critical-sized calvarial bone defect model. Our study shows the potential utility of SF scaffolds with nanofibrous structures and enriched inorganic components in bone tissue engineering.

Colour-Value Based Method for Polydopamine Coating-Stability Characterization on Polyethersulfone Membranes

Porous polyethersulfone membranes as used in oenology were investigated in order to evaluate temperature-dependent permeances in a temperature range from 10 to 35 °C. A temperature correction factor was determined for this type of membrane to get accurate and comparable results for further developments. Moreover, the membranes were modified with a bio-inspired polydopamine coating in order to reduce fouling. The performance of the membranes could be increased with respect to permeance and flux recovery under cross-flow conditions. In order to test the applicability and stability of the coating layer, they were treated with basic and acidic cleaning agents as used in industry for fouled membranes. The chemical stability of the coating layer was studied under basic and acidic conditions, by systematic observation of the colour change of the coated membranes over treatment time.

Polydopamine Coatings with Nanopores for Versatile Molecular Separation

The demand for highly efficient and multifunctional membranes in various separation processes is increasing. Recently, mussel-inspired polydopamine (PDA) has provided a promising way to meet these requirements because of its surface-adhesive property and film-forming ability. However, traditional PDA coatings usually suffer from the disadvantages of nonuniformity, incompactness, and instability, leading to poor molecular separation and service performance. Herein, uniform, compact, and robust PDA coatings were fabricated on an ultrafiltration substrate via a reasonable screening of oxidants for the oxidized self-polymerization of dopamine. The as-prepared PDA coatings were nanoporous (0.56 ± 0.04 and 0.93 ± 0.04 nm) with a thickness of ∼75 nm, which endows the composite membranes with a high solute rejection and solvent permeability during molecular separation. They are useful in organic solvent nanofiltration because of their superior structural stability. Moreover, the composite membranes can be used for recycling the nanometer catalyst from organic solvents for the first time, which has significantly broadened the potential applications of these mussel-inspired coatings for versatile separation processes.

Facile construction of a polydopamine-based hydrophobic surface for protection of metals against corrosion

Metal surfaces with a hydrophobic feature, which could prevent percolation of water droplets and improve their capability against corrosion, arouse extensively interest.

Additively Manufactured Macroporous Titanium with Silver-Releasing Micro-/Nanoporous Surface for Multipurpose Infection Control and Bone Repair - A Proof of Concept

Restoring large-scale bone defects, where osteogenesis is slow while infections lurk, with biomaterials represents a formidable challenge in orthopedic clinics. Here, we propose a scaffold-based multipurpose anti-infection and bone repairing strategy to meet such restorative needs. To do this, personalized multifunctional titanium meshes were produced through an advanced additive manufacturing process and dual "TiO₂-poly(dopamine)/Ag (nano)" post modifications, yielding macroporous constructs with micro-/nanoporous walls and nanosilver bullets immobilized/embedded therein. Ultrahigh loading capacity and durable release of Ag⁺ were accomplished. The scaffolds were active against planktonic/adherent bacteria (Gram-negative and positive) for up to 12 weeks. Additionally, they not only defended themselves from biofilm colonization but also helped destroy existing biofilms, especially in combination with antibiotics. Further, the osteoblasts/bacteria coculture study displayed that the engineered surfaces aided MG-63 cells to combat bacterial invasion. Meanwhile, the scaffolds elicited generally acceptable biocompatibility (cell adhesion, proliferation, and viability) and hastened osteoblast differentiation and maturation (alkaline phosphatase production, matrix secretion, and calcification), by synergy of micro-/nanoscale topological cues and bioactive catecholamine chemistry. Although done ex vivo, these studies reveal that our three-in-one strategy (infection prophylaxis, infection fighting, and bone repair) has great potential to simultaneously prevent/combat infections and bridge defected bone. This work provides new thoughts to the use of enabling technologies to design biomaterials that resolve unmet clinical needs.

Preparation of Thin Melanin-Type Films by Surface-Controlled Oxidation

The preparation of thin melanin films suitable for applications is challenging. In this work, we present a new alternative approach to thin melanin-type films using oxidative multilayers prepared by the sequential layer-by-layer deposition of cerium(IV) and inorganic polyphosphate. The interfacial reaction between cerium(IV) in the multilayer and 5,6-dihydroxyindole (DHI) in the adjacent aqueous solution leads to the formation of a thin uniform film. The oxidation of DHI by cerium(IV) proceeds via known melanin intermediates. We have characterized the formed DHI-melanin films using scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), UV-vis spectroscopy, and spectroelectrochemistry. When a five-bilayer oxidative multilayer is used, the film is uniform with a thickness of ca. 10 nm. Its chemical composition, as determined using XPS, is typical for melanin. It is also redox active, and its oxidation occurs in two steps, which can be assigned to semiquinone and quinone formation within the indole structural motif. Oxidative multilayers can also oxidize dopamine, but the reaction stops at the dopamine quinone stage because of the limited amount of the multilayer-based oxidizing agent. However, dopamine oxidation by Ce(IV) was studied also in solution by UV-vis spectroscopy and mass spectrometry in order to verify the reaction mechanism and the final product. In solution, the oxidation of dopamine by cerium shows that the indole ring formation takes place already at low pH and that the mass spectrum of the final product is practically identical with that of commercial melanin. Therefore, layer-by-layer formed oxidative multilayers can be used to deposit functional melanin-type thin films on arbitrary substrates by a surface-controlled reaction.

Manipulating the multifunctionalities of polydopamine to prepare high-flux anti-biofouling composite nanofiltration membranes

An anti-biofouling composite NF membrane was prepared through the rational manipulation of the adhesion, reaction and separation functionalities of PDA.

Bioadhesion-inspired fabrication of robust thin-film composite membranes with tunable solvent permeation properties

Dopamine chemistry arising from marine mussel bioadhesion principles has attracted growing interest in designing and fabricating robust thin films/membranes for various chemical separation processes.

Towards mussel-like on-demand coatings: light-triggered polymerization of dopamine through a photoinduced pH jump

Polydopamine polymerization was achieved through a photoinduced pH jump involving the irradiation of a photobase generator.

High-performance multilayer composite membranes with mussel-inspired polydopamine as a versatile molecular bridge for CO2 separation

It is desirable to develop high-performance composite membranes for efficient CO2 separation in CO2 capture process. Introduction of a highly permeable polydimethylsiloxane (PDMS) intermediate layer between a selective layer and a porous support has been considered as a simple but efficient way to enhance gas permeance while maintaining high gas selectivity, because the introduced intermediate layer could benefit the formation of an ultrathin defect-free selective layer owing to the circumvention of pore penetration phenomenon. However, the selection of selective layer materials is unfavorably restricted because of the low surface energy of PDMS. Various highly hydrophilic membrane materials such as amino group-rich polyvinylamine (PVAm), a representative facilitated transport membrane material for CO2 separation, could not be facilely coated over the surface of the hydrophobic PDMS intermediate layer uniformly. Inspired by the hydrophilic nature and strong adhesive ability of polydopamine (PDA), PDA was therefore selected as a versatile molecular bridge between hydrophobic PDMS and hydrophilic PVAm. The PDA coating endows a highly compatible interface between both components with a large surface energy difference via multiple-site cooperative interactions. The resulting multilayer composite membrane with a thin facilitated transport PVAm selective layer exhibits a notably enhanced CO2 permeance (1887 GPU) combined with a slightly improved CO2/N2 selectivity (83), as well as superior structural stability. Similarly, the multilayer composite membrane with a hydrophilic CO2-philic Pebax 1657 selective layer was also developed for enhanced CO2 separation performance.