Preparation of patterned zinc oxide films by breath figure templating

Bio-Inspired Silica Films Combining Block Copolymers Self-Assembly and Soft Chemistry: Paving the Way toward Artificial Exosqueleton of Seawater Diatoms

This review is in line with the principles of bio-inspiration and biomimicry in order to envisage a softer and more environmentally friendly chemistry. Here, the source of inspiration is a microalga from the oceans with the ability to build an exoskeleton of silica under ambient conditions. Following this model, this review is interested in different ways of creating porous silica films with a hierarchical porosity similar to diatoms. For this purpose, polymeric/hybrid/inorganic films structured in honeycomb using the breath figure method are reported. This versatile and easy to implement method based on the principle of rapid evaporation of a solvent in a humid atmosphere is widely used in the formation of structured films with micron-sized pores. In addition to this, the self-assembly of copolymer at the nanoscale can be addressed to obtain a hierarchically structured film. Following this structuration step, the degradation of a sacrificial block is then described from the most energy-intensive to soft process, allowing an added nanoporosity to the micron porosity of the BF method. Finally, hierarchical porous silica films are described using the sol-gel process, which is known as a soft chemistry process.

Jamming and percolation of linear k-mers on honeycomb lattices

Numerical simulations and finite-size scaling analysis have been performed to study the jamming and percolation behavior of elongated objects deposited on two-dimensional honeycomb lattices. The depositing particle is modeled as a linear array of length k (so-called k-mer), maximizing the distance between first and last monomers in the chain. The separation between k-mer units is equal to the lattice constant. Hence, k sites are occupied by a k-mer when adsorbed onto the surface. The adsorption process starts with an initial configuration, where all lattice sites are empty. Then, the sites are occupied following a random sequential adsorption mechanism. The process finishes when the jamming state is reached and no more objects can be deposited due to the absence of empty site clusters of appropriate size and shape. Jamming coverage θ_{j,k} and percolation threshold θ_{c,k} were determined for a wide range of values of k (2≤k≤128). The obtained results shows that (i) θ_{j,k} is a decreasing function with increasing k, being θ_{j,k→∞}=0.6007(6) the limit value for infinitely long k-mers; and (ii) θ_{c,k} has a strong dependence on k. It decreases in the range 2≤k<48, goes through a minimum around k=48, and increases smoothly from k=48 up to the largest studied value of k=128. Finally, the precise determination of the critical exponents ν, β, and γ indicates that the model belongs to the same universality class as 2D standard percolation regardless of the value of k considered.

Prediction of zinc-binding sites using multiple sequence profiles and machine learning methods

The zinc (Zn²⁺) cofactor has been proven to be involved in numerous biological mechanisms and the zinc-binding site is recognized as one of the most important post-translation modifications in proteins. Therefore, accurate knowledge of zinc ions in protein structures can provide potential clues for elucidation of protein folding and functions. However, determining zinc-binding residues by experimental means is usually lab-intensive and associated with high cost in most cases. In this context, the development of computational tools for identifying zinc-binding sites is highly desired, especially in the current post-genomic era. In this work, we developed a novel zinc-binding site prediction method by combining several intensively-trained machine learning models. To establish an accurate and generative method, we downloaded all zinc-binding proteins from the Protein Data Bank and prepared a non-redundant dataset. Meanwhile, a well-prepared dataset by other groups was also used. Then, effective and complementary features were extracted from sequences and three-dimensional structures of these proteins. Moreover, several well-designed machine learning models were intensively trained to construct accurate models. To assess the performance, the obtained predictors were stringently benchmarked using the diverse zinc-binding sites. Furthermore, several state-of-the-art in silico methods developed specifically for zinc-binding sites were also evaluated and compared. The results confirmed that our method is very competitive in real world applications and could become a complementary tool to wet lab experiments. To facilitate research in the community, a web server and stand-alone program implementing our method were constructed and are publicly available at . The downloadable program of our method can be easily used for the high-throughput screening of potential zinc-binding sites across proteomes.

The Effect of the Isomeric Chlorine Substitutions on the Honeycomb-Patterned Films of Poly(x-chlorostyrene)s/Polystyrene Blends and Copolymers via Static Breath Figure Technique

Polymeric thin films patterned with honeycomb structures were prepared from poly(x-chlorostyrene) and statistical poly(x-chlorostyrene-co-styrene) copolymers by static breath figure method. Each polymeric sample was synthesized by free radical polymerization and its solution in tetrahydrofuran cast on glass wafers under 90% relative humidity (RH). The effect of the chorine substitution in the topography and conformational entropy was evaluated. The entropy of each sample was calculated by using Voronoi tessellation. The obtained results revealed that these materials could be a suitable toolbox to develop a honeycomb patterns with a wide range of pore sizes for a potential use in contact guidance induced culture.

Preparation of Hierarchical Highly Ordered Porous Films of Brominated Poly(phenylene oxide) and Hydrophilic SiO₂/C Membrane via the Breath Figure Method

Porous permeable films materials have very broad prospects in the treatment of sludge-containing waste water due to their large surface area and good microfiltration. In this work, highly ordered porous membranes have been prepared successfully on ice substrates using a poly(phenylene oxide) (BPPO)-SiO₂ nanoparticle (NP) mixture by the brePorous permeable films materials have very broad prospects in the treatment of sludge-containing waste water due to their large surface area and good microfiltration. In this work, highly ordered porous membranes have been prepared successfully on ice substrates using aath figure method. Based on the theory of Pickering emulsion system and capillary flow, particle assisted membrane formation was analyzed. Another two sorts of new membranes SiO₂/C membrane and hierarchical porous polymer (HPP) membrane, which were obtained by modification of the BPPO-SiO₂ membrane by calcination and etching, were set up in a further study. Their properties were investigated through the methods of scanning electron microscopy (SEM), fourier transform infrared spectrometry (FTIR), ultraviolet spectrum (UV), capillary electrophoresis (CE), contact angle, and water flux tests. All these results demonstrate that both surface hydrophilicity and fouling resistance of the membrane would be improved by using SiO₂ as a filler. The membranes with high permeability and antifouling properties were used for microfiltration applications.

Hierarchically Structured Macro with Nested Mesoporous Zinc Indium Oxide Conducting Film

Fabrication of homogeneously distributed (HD) macropores by breath figure process is an active research area. Adopting the process, for the first time, we report the fabrication of HD macro with nested meso (hierarchical) porous nanocrystalline zinc indium oxide conducting sol-gel thin film on glass by dip-coating at 45-50% room relative humidity (RH) from a solution in ethanol-2-butanol (1:1, w/w) medium with a 1:1, Zn:In ratio. In this process, solution composition and RH are found to play key roles on HD macropore generation. The film is highly promising toward visible-light-driven photoelectrochemical water splitting.

Multiphase Media Antiadhesive Coatings: Hierarchical Self-Assembled Porous Materials Generated Using Breath Figure Patterns

The cleaning of interface pollutants typically consumes a large amount of energy. Therefore, the development of multiphase media antiadhesive materials is urgently required to meet the demand of energy savings and environmental protection. In this study, the antiadhesive properties toward several liquid droplets and bubbles in multiple media are demonstrated on a porous Fe₂O₃ coating, which is prepared via a facile spin-coating-assisted breath figure approach and a phase separation strategy. The prominent antiadhesive characteristic of these porous surfaces lies in their high-surface-energy hierarchical micro/nanoscale structure, which easily entraps one medium (oil or water) in the pore and repels other unmixable liquids and air bubbles. In addition, we successfully demonstrate an antifouling application of the coating, which shows excellent antiadhesive and super-antiwetting characteristics under multiple liquids. Our work extends relevant antiadhesion research from a single medium to multiple media and promises to broaden the applications of antiadhesive materials in sophisticated activities performed under complicated liquid environments, such as marine antifouling or pipeline transportation.

Amino-functionalized breath-figure cavities in polystyrene-alumina hybrid films: effect of particle concentration and dispersion

We report the formation of breath-figure (BF) patterns with amino-functionalized cavities in a BF incompatible polystyrene (PS) by incorporating functionalized alumina nanoparticles. The particles were amphiphilic-modified and the modifier ratio was regulated to achieve a specific hydrophobic/hydrophilic balance of the particles. The influence of the physical and chemical properties of the particles like particle concentration, the hydrophobic/hydrophilic balance, etc., on particle dispersion in solvents having different polarity and the corresponding changes in the BF patterns have been studied. The amphiphilic-modified alumina particles could successfully assist the BF mechanism, generating uniform patterns in polystyrene films with the cavity walls decorated with the functionalized alumina particles, even from water-miscible solvents like THF. The possibility of fabricating free-standing micropatterned films by casting and drying the suspension under ambient conditions was also demonstrated. The present method opens up a simple route for producing functionalized BF cavities, which can be post-modified by a chemical route for various biological applications.

Ordered porous structure hybrid films generated by breath figures for directional water penetration

A highly ordered open-pore hybrid film was fabricated by controlling the substrate roughness and wettability. The composite with different wettability on the two side resulted in an attractive unidirectional water-penetration function (see figure).

Printing holes by a dewetting solution enables formation of a transparent conductive film

We present hereby a general approach for rapid fabrication of large scale, patterned transparent conductive coatings composed of nanoparticles. The approach is based on direct formation of "2D holes" with controllable diameter onto a thin film composed of metal nanoparticles. The holes are formed by inkjet printing a dewetting aqueous liquid, which pushes away the metal nanoparticles, thus forming a transparent array of interconnected conductive rings.

Breath Figures of Nanoscale Bricks: A Universal Method for Creating Hierarchic Porous Materials from Inorganic Nanoparticles Stabilized with Mussel-Inspired Copolymers

High-performance catalysts and photovoltaics are required for building an environmentally sustainable society. Because catalytic and photovoltaic reactions occur at the interfaces between reactants and surfaces, the chemical, physical, and structural properties of interfaces have been the focus of much research. To improve the performance of these materials further, inorganic porous materials with hierarchic porous architectures have been fabricated. The breath figure technique allows preparing porous films by using water droplets as templates. In this study, a valuable preparation method for hierarchic porous inorganic materials is shown. Hierarchic porous materials are prepared from surface-coated inorganic nanoparticles with amphiphilic copolymers having catechol moieties followed by sintering. Micron-scale pores are prepared by using water droplets as templates, and nanoscale pores are formed between the nanoparticles. The fabrication method allows the preparation of hierarchic porous films from inorganic nanoparticles of various shapes and materials.

Dispersion of Al2O3 nanoparticles stabilized with mussel-inspired amphiphilic copolymers in organic solvents and formation of hierarchical porous films by the breath figure technique

Hierarchical porous inorganic materials have attracted much attention, due to their large surface area and fast substance diffusion. We have prepared hierarchical porous films composed of Al2O3 nanoparticles (NPs) using the breath figure technique. The Al2O3 NPs were stabilized using an amphiphilic copolymer that contained catechol moieties. Porous films of polymer-stabilized Al2O3 NPs were prepared using water droplets as templates. The films were sintered to produce hierarchical porous Al2O3 films that were thermally and chemically stable.

Ordered honeycomb structural interfaces for anticancer cells growth

The patterned honeycomb structure film with the aggregation-induced emission property was prepared successfully by the breath figure method and photopolymerization method. Characterization of the HeLa and HepG2 cell culture on this surface indicates the porous honeycomb structures show anticancer cells growth function. So this kind of honeycomb structure will be promising for the control of cancer cell growth behaviors and achieving the application of anticancer.

Bioinspired design of honeycomb structure interfaces with controllable water adhesion

Inspired by biological attachment systems, we fabricated the honeycomb structural films with different diameters by breath figure (BF) method, which were similar to the patterned octopus suckers. The experimental results showed, besides different van der Waals forces between the polystyrene (PS) surfaces and water, another important factor; that is, different negative pressures produced by different volumes of sealed air could be a crucial factor for the different adhesions. So the water adhesive forces of the as-prepared films can be effectively controlled from relative high to relative low adhesion by varying the pore diameters, which effectively adjusted the negative pressures produced by the pores. This unique adhesive phenomenon of honeycomb structure will be very useful for manipulating water droplet behaviors, as well as controlling liquid collection and transportation. These findings are interesting and helpful for us to further understand the biological attachment systems and to optimize the design of artificial analogues.

Fabrication of structured porous films by breath figures and phase separation processes: tuning the chemistry and morphology inside the pores using click chemistry

Herein, a facile water-assisted templating technique, the so-called breath figures method, in combination with phase separation process, was employed to prepare multifunctional micropatterned films. Tetrahydrofuran solutions of incompatible ternary blends consisting of high-molecular-weight polystyrene, an amphiphilic block copolymer, polystyrene-b-poly[poly(ethylene glycol) methyl ether methacrylate] (PS40-b-P(PEGMA300)48), and a fluorinated homopolymer, poly(2,3,4,5,6-pentafluorostyrene) (P5FS21) were casted under humid atmosphere varying the proportion of the components. Two simultaneously occurring processes, i.e., the breath figures mechanism and the phase separation process, lead to unprecedented morphologies that could be tuned by simply varying the relative humidity or the composition of the blend. Confocal micro-Raman spectroscopy served to provide information about the location and distribution of the different functionalities in the films. As a result, both the amphiphilic block copolymer and the fluorinated polymer were mainly located in the cavities. Above a certain percentage of relative humidity, honeycomb structured films were obtained in which the block copolymer is distributed on the edge of the pore as a result of the affinity by the condensing water droplet and the coffee stain effect. The homopolymer is also preferentially situated at the pore edge, but forming spherical domains with narrow polydisperse sizes. Moreover, thiolated glucose molecules were specifically attached to the P5FS21 domains via thiol-para fluorine "click" reaction. Subsequently, the specific lectin (Concanavalin A, Canavalia ensiformis) was attached to the surface by conjugation with the glucose moieties. The successful binding of the Con A was demonstrated by the fluorescence, observed exclusively at the areas where P5FS21 domains are located. This nonlithographic method opens a new route to fabricate a huge variety of microstructured polymer films in terms of morphology not only for protein patterning, as illustrated in this manuscript, but also to produce a diversity of functional group arrangements.

Advances in Fabrication Materials of Honeycomb Structure Films by the Breath-Figure Method

Creatures in nature possess almost perfect structures and properties, and exhibit harmonization and unification between structure and function. Biomimetics, mimicking nature for engineering solutions, provides a model for the development of functional surfaces with special properties. Recently, honeycomb structure materials have attracted wide attention for both fundamental research and practical applications and have become an increasingly hot research topic. Though progress in the field of breath-figure formation has been reviewed, the advance in the fabrication materials of bio-inspired honeycomb structure films has not been discussed. Here we review the recent progress of honeycomb structure fabrication materials which were prepared by the breath-figure method. The application of breath figures for the generation of all kinds of honeycomb is discussed.

Honeycomb Films from Perfluoropolyether-Based Star and Micelle Architectures

A perfluoropolyether-b-poly(t-butyl acrylate) (PFPE-b-PtBA) block copolymer macroinitiator was used to prepare both core cross-linked star (CCS) polymers and micelles, whereby the outer shell and core, respectively, are comprised of fluorinated segments. The star polymer complete with PFPE outer shell was synthesised via atom transfer radical polymerisation (ATRP) and the arm-first approach, through cross-linking of the PFPE-b-PtBA macroinitiator with ethylene glycol diacrylate (EGDA). Alternatively, the PFPE-b-PtBA block copolymer could be self-assembled in benzene to form micelles with a PtBA shell and PFPE core. Both the micelle and CCS polymer were subsequently fabricated into non-cracking honeycomb (HC) patterned films on both planar and non-planar surfaces via the ‘Breath Figure’ (BF) technique using a static casting system.