Synthesis and Characterization of Polystyrene-b-poly(ethylene oxide)-b-poly(ε-caprolactone) Block Copolymers

Crystallization and Morphology of Triple Crystalline Polyethylene-b-poly(ethylene oxide)-b-poly(ε-caprolactone) PE-b-PEO-b-PCL Triblock Terpolymers

The morphology and crystallization behavior of two triblock terpolymers of polymethylene, equivalent to polyethylene (PE), poly (ethylene oxide) (PEO), and poly (ε-caprolactone) (PCL) are studied: PE₂₂^7.1-b-PEO₄₆^15.1-b-PCL₃₂^10.4 (T1) and PE₃₇^9.5-b-PEO₃₄^8.8-b-PCL₂₉^7.6 (T2) (superscripts give number average molecular weights in kg/mol and subscripts composition in wt %). The three blocks are potentially crystallizable, and the triple crystalline nature of the samples is investigated. Polyhomologation (C1 polymerization), ring-opening polymerization, and catalyst-switch strategies were combined to synthesize the triblock terpolymers. In addition, the corresponding PE-b-PEO diblock copolymers and PE homopolymers were also analyzed. The crystallization sequence of the blocks was determined via three independent but complementary techniques: differential scanning calorimetry (DSC), in situ SAXS/WAXS (small angle X-ray scattering/wide angle X-ray scattering), and polarized light optical microscopy (PLOM). The two terpolymers (T1 and T2) are weakly phase segregated in the melt according to SAXS. DSC and WAXS results demonstrate that in both triblock terpolymers the crystallization process starts with the PE block, continues with the PCL block, and ends with the PEO block. Hence triple crystalline materials are obtained. The crystallization of the PCL and the PEO block is coincident (i.e., it overlaps); however, WAXS and PLOM experiments can identify both transitions. In addition, PLOM shows a spherulitic morphology for the PE homopolymer and the T1 precursor diblock copolymer, while the other systems appear as non-spherulitic or microspherulitic at the last stage of the crystallization process. The complicated crystallization of tricrystalline triblock terpolymers can only be fully grasped when DSC, WAXS, and PLOM experiments are combined. This knowledge is fundamental to tailor the properties of these complex but fascinating materials.

Analysis of individual block length of amphiphilic di- & tri-block copolymers containing poly(ethylene oxide) and poly(methyl methacrylate)

Estimation of individual block lengths and extent of homopolymers.

Azeotrope enabled polymerization of ethylene oxide

We report a synthetic route for poly(ethylene oxide) (PEO) using azeotropic distillation to remove water and drive the equilibrium of an alkyl hydroxide and potassium hydroxide to potassium alkoxide, avoiding the use of pyrophoric organometallics.

Supramolecular hydrogels of α-cyclodextrin/reverse poloxamines/carbon-based nanomaterials and its multi-functional application

Supramolecular hydrogels were prepared using α-cyclodextrin (α-CD) and a poloxamine (reverse Tetronic 90R4, T90R4) which has four diblock arms with a poly(propylene oxide)–poly(ethylene oxide) (PPO–PEO) structure.

Synthesis of thermally cleavable multisegmented polystyrene by an atom transfer nitroxide radical polymerization (ATNRP) mechanism

Based on the common features of well-defined NRC reaction, ATRP and NMRP mechanisms, an atom transfer nitroxide radical polymerization (ATNRP) mechanism was presented, and further used to construct multisegmented PS_m embedded with multiple alkoxyamine linkages.

Crystallization induced layer-to-layer transitions in symmetric PEO-b-PLLA block copolymer with synchrotron simultaneous SAXS/WAXS investigations

Detailed synchrotron simultaneous SAXS/WAXS investigation on crystallization induced layer-to-layer transitions of PEO-b-PLLA.

Multifunctional photo-crosslinked polymeric ionic hydrogel films

The crosslinked ionic hydrogel films prepared by photopolymerization have multiple applications as magnetic, catalytic, antibiotic, and fluorescent materials.

Poly(ethylene oxide) (PEO)-based ABC triblock terpolymers – synthetic complexity vs. application benefits

This review presents a short summary of possible synthetic routes for the synthesis of poly(ethylene oxide) (PEO) containing triblock terpolymers, as well as different applications in the bulk or in solution – including the preparation of porous materials, hybrid systems, and carriers for controlled drug delivery.

MOLECULAR MODELING OF THERMAL AND MECHANICAL PROPERTIES OF ELASTOMERS: A REVIEW

Elastomers have varied applications from adhesives, sealants, encapsulants, and coatings to specialty usage in electronics, aviation, optical, and communications industries due to their high structural stability. In addition, more and more biological applications of elastomeric compounds are gaining ground, particularly in mimetic architecture. Modeling and simulation provide tools by which the interactions leading to various structure–property relationships can be explored at the micro level. An understanding of these processes could cut down on the extensive and expensive trial-and-error experiments as well as provide a benchmark for material design. This review article explores the work done by different groups, especially at the molecular level, to model the properties of both thermoplastic and thermoset elastomers. Each presents its own challenges and solutions: from microphase separation to network building and force field parameterization. The results of these modeling efforts along with the challenges are presented in this review work.