Poly(propylene-g-styrene) Graft Copolymers with Well-Defined Microstructure by Metallocene Catalyzed Copolymerization of Propylene with Allyl-Terminated Polystyrene Macromonomers

Synthesis and characterization of brush-like multigraft copolymers PnBA-g-PMMA by a combination of emulsion AGET ATRP and emulsion polymerization

In this paper, poly(n-butyl acrylate)-g-poly(methyl methacrylate) multigraft copolymers were synthesized by macromonomer technique and miniemulsion copolymerization. The PMMA macromonomers were obtained by an activator generated by electron transfer atom transfer radical polymerization (AGET ATRP) in emulsion system and subsequent allylation. Then the copolymerization of different macromonomers with nBA was carried out in miniemulsion system, obtaining multigraft copolymers with high molecular weight. The latex particles and distribution of emulsion AGET ATRP and miniemulsion copolymerization were characterized using laser light scattering. The molecular weight and polydispersity indices of macromonomers and multigraft copolymers were analyzed by gel permeation chromatography, and the number-average molecular weight range is 187,600-554,800 g/mol for PnBA-g-PMMA copolymers. In addition, the structural characteristics of macromonomer and brush-like copolymers were determined by infrared spectra and (1)H nuclear magnetic resonance spectroscopy. The thermal performance of brush-like copolymers were characterized by differential scanning calorimetry and thermogravimetric analysis. Atomic force microscopy results showed that the degree of microphase separation was varying with increasing PMMA content in PnBA-g-PMMA. The dynamic rheometer analysis revealed that multigraft copolymer with PMMA content of 31.4% exhibited good elastomeric properties to function as a TPE. These multigraft copolymers show a promising low cost and environmental friendly thermoplastic elastomer.

Synthesis and characterization of graft copolymers PnBA-g-PS by miniemulsion polymerization

PnBA-g-PS by emulsion AGET ATRP and miniemulsion polymerization.

Synthesis of Allyl-Terminated Polar Macromonomers by Metallocene-Catalyzed Polymerizations of 10-Undecene-1-ol

Poly(10-undecene-1-ol) macromonomers were synthesized by metallocene-catalyzed polymerization using vinyl chloride as a chain transfer agent. Using this technique, predominantly allyl terminated polymers could be obtained, which was verified by NMR spectroscopy and matrix-assisted laser desorption ionization time-of-flight mass spectrometry (MALDI-TOF-MS). By means of the mass spectra, a detailed interpretation of the nature of the head and end groups of these polymers was possible.

Controlled nitroxide-mediated styrene surface graft polymerization with atmospheric plasma surface activation

Polymer layer growth by free radical graft polymerization (FRGP) and controlled nitroxide-mediated graft polymerization (NMGP) of polystyrene was achieved by atmospheric pressure hydrogen plasma surface activation of silicon. Kinetic polystyrene layer growth by atmospheric pressure plasma-induced FRGP (APPI-FRGP) exhibited a maximum surface-grafted layer thickness (125 A after 20 h) at an initial monomer concentration of [M] 0 = 2.62 M at 85 degrees C. Increasing both the reaction temperature ( T = 100 degrees C) and initial monomer concentration ([M] 0 = 4.36 M) led to an increased initial film growth rate but a reduced polymer layer thickness, due to uncontrolled thermal initiation and polymer grafting from solution. Controlled atmospheric pressure plasma-induced NMGP (APPI-NMGP), using 2,2,6,6-tetramethyl-1-piperidinyloxy (TEMPO), exhibited a linear increase in grafted polystyrene layer growth with time due to controlled surface graft polymerization as well as reduced uncontrolled solution polymerization and polymer grafting, resulting in a polymer layer thickness of 285 A after 60 h at [TEMPO] = 10 mM, [M] 0 = 4.36 M, and T = 120 degrees C. Atomic force microscopy (AFM) surface analysis demonstrated that polystyrene-grafted surfaces created by APPI-NMGP exhibited a high surface density of spatially homogeneous polymer features with a low root-mean-square (RMS) surface roughness ( R rms = 0.36 nm), similar to that of the native silicon surface ( R rms = 0.21 nm). In contrast, polymer films created by APPI-FRGP at [M] 0 = 2.62 M demonstrated an increase in polymer film surface roughness observed at reaction temperatures of 85 degrees C ( R rms = 0.55 nm) and 100 degrees C ( R rms = 1.70 nm). The present study concluded that the current approach to APPI controlled radical polymerization may be used to achieve a grafted polymer layer with a lower surface roughness and a higher fractional coverage of surface-grafted polymers compared to both conventional FRGP and APPI-FRGP.