13C Solid-State NMR of the Mobile Phase of Poly(vinylidene fluoride)

Multiple energy dissipation modes in dynamic polymer networks with neutral and ionic junctions

Polymer networks with controlled ratios of neutral and ionic dynamic crosslink points were prepared from ethylene glycol, boric acid, and lithium hydroxide. Both neutral and ionic sites led to the emergence of distinct damping modes separate from the glass transition. This work highlights the potential of polymer networks for multimodal damping spectra through dynamic bond selection.

Electro-Assisted 3D Printing Multi-Layer PVDF/CaCl2 Composite Films and Sensors

Polyvinylidene fluoride (PVDF) films are widely used in sensors for their wide response frequency, good flexibility, low acoustic impedance, and chemical stability. In this work, PVDF/CaCl2 piezoelectric films were prepared by an electro-assisted 3D printing method and used to form a multi-layer composite film sensor. The study found that the addition of CaCl2 can effectively increase the β-phase content in the PVDF film and improve the piezoelectric and dielectric properties of the PVDF composite film sensors. When the content of CaCl2 is 0.15 wt.%, the β-phase content of the PVDF/CaCl2 composite film can reach the highest value of up to 48.47%, and the output voltage response of the sensor is 0.62 V at an input frequency of 10 Hz, 10 V voltage. The output voltage of PVDF composite film sensor with two and three layers is 1.306 and 1.693 times that of a single layer, respectively. The sensitivity of the multi-layer sensors has also been greatly improved.

Reversible Deposition and Stripping of the Cathode Electrolyte Interphase on Li2RuO3

Performance decline in Li-excess cathodes is generally attributed to structural degradation at the electrode-electrolyte interphase, including transition metal migration into the lithium layer and oxygen evolution into the electrolyte. Reactions between these new surface structures and/or reactive oxygen species in the electrolyte can lead to the formation of a cathode electrolyte interphase (CEI) on the surface of the electrode, though the link between CEI composition and the performance of Li-excess materials is not well understood. To bridge this gap in understanding, we use solid-state nuclear magnetic resonance (SSNMR) spectroscopy, dynamic nuclear polarization (DNP) NMR, and electrochemical impedance spectroscopy (EIS) to assess the chemical composition and impedance of the CEI on Li₂RuO₃ as a function of state of charge and cycle number. We show that the CEI that forms on Li₂RuO₃ when cycled in carbonate-containing electrolytes is similar to the solid electrolyte interphase (SEI) that has been observed on anode materials, containing components such as PEO, Li acetate, carbonates, and LiF. The CEI composition deposited on the cathode surface on charge is chemically distinct from that observed upon discharge, supporting the notion of crosstalk between the SEI and the CEI, with Li⁺-coordinating species leaving the CEI during delithiation. Migration of the outer CEI combined with the accumulation of poor ionic conducting components on the static inner CEI may contribute to the loss of performance over time in Li-excess cathode materials.

Adsorption of Pb(II) by a polyvinylidene fluoride membrane bearing chelating poly(amino phosphonic acid) and poly(amino carboxylic acid) groups

Pb(II) can cause a hazardous effect on ecosystem and public health due to its high biotoxicity. A polyvinylidene fluoride-type membrane bearing both poly(amino phosphonic acid) and poly(amino carboxylic acid) functional groups was fabricated for the purpose of Pb(II) removal from the aqueous solutions. The adsorption behaviors of the fabricated chelating membrane toward Pb(II) were studied by the series of static and continuous adsorption experiments. When the pH, adsorption equilibrium time, initial Pb(II) concentration, and temperature were 5.1, 300 min, 1.0 mmol g−1, and 298 K, respectively, Pb(II) uptake of the membrane was 1.1 mmol g−1. The presence of coexisting metal ions and complexing reagents decreased the Pb(II) uptake. The adsorption kinetic and isotherm adsorption followed pseudo-second-order equation and Langmuir model, respectively; this adsorption process showed a spontaneous and exothermic feature. The bed depth service time and Thomas models were suitable for describing obtained breakthrough curves.