Sensitive Characterization of the Influence of Substrate Interfaces on Supported Thin Films

Glass transition temperature of single-chain polystyrene particles end-grafted to oxide-coated silicon

A method based on the PeakForce QNM atomic force microscopic (AFM) adhesion measurement is employed to investigate the glassy dynamics of polystyrene (PS) single-chain particles end-grafted to SiO₂-Si substrates with different diameters, D₀, of 3.4 nm-8.8 nm and molar masses, M_n, of 8-123 kg/mol. As temperature was increased, the adhesion force, F_ad, experienced by the AFM tip on pulling off the single chains after loading demonstrated a stepwise increase at an elevated temperature, which we identified to be T_g based on previous works. Our result shows that T_g of our grafted single chains increases with M_n in a manner consistent with the Fox-Flory equation, but the coefficient quantifying the M_n dependence of T_g is only (36 ± 6)% the value of bulk PS. In addition, the value of T_g in the M_n → ∞ limit is about 25 °C below the bulk T_g but more than 15 °C above that of (untethered) PS nanoparticles with D₀ ≈ 100 nm suspended in a solution. Our findings are consistent with T_g of our single chains being dominated by simultaneous effects of the interfaces, which depress T_g, and end-grafting, which enhances T_g. The latter is believed to exert its influence on the glass transition dynamics by a mechanism reliant on chain connectivity and does not vary with chain length.

Viscosity and fragility of confined polymer nanocomposites: a tale of two interfaces

Viscosity and fragility are key parameters determining the processability and thermo-mechanical stability of glassy polymers and polymer nanocomposites (PNCs). In confined polymers, these parameters are largely dominated by the long relaxation times of the polymers adsorbed at the substrate-polymer interface. On the other hand, for polymer nanocomposites, the interface layer (IL) between the nanoparticles and the surrounding matrix chains often control not only the morphology and dispersion but also various parameters like viscosity and glass transition temperature. Confined PNCs, hence, present a unique opportunity to study the interplay of these two independent interfacial effects. Here, we report the results of X-ray scattering based dynamics measurements of PNC thin films, with a two IL width, unraveling the subtle interplay of these two interfaces on the measured viscosity and fragility. Coupled with coarse-grained molecular dynamics (MD) simulations, our experimental results demonstrate that the viscosity of the PNC films increases with both the IL width and the thickness of the polymer layer adsorbed at the substrate interface. However, while both pristine PS and PNCs with a higher IL width become stronger glasses, as estimated by their fragility, the PNC with a lower IL width shows an increase in fragility with increasing confinement. Our results suggest a novel method to control thermo-mechanical properties and stability of PNC coatings by independently controlling the two interfacial effects in athermal glassy PNCs.

Effect of substrate interactions on the glass transition and length-scale of correlated dynamics in ultra-thin molecular glass films

Interfacial interactions can play an important role in the glass transition temperature (T _g ) and relaxation dynamics of ultra-thin glass polymer films. We have recently shown that similar to the polymeric systems in ultra-thin molecular glass films of N, N'-Bis(3-methylphenyl)-N, N'-diphenylbenzidine (TPD), the T _g is reduced and dynamics are enhanced. Furthermore, in molecular glass systems, as the film thickness is reduced below ∼30 nm, the dynamics at the two interfaces correlate such that the range of the gradients in the dynamics induced by the free surface narrows compared to thicker films. These observations indicate that the dynamics of the glassy thin films are strongly correlated and cannot be explained by a simple two-layer model consisting of a bulk and a thin interfacial layer with a constant thickness and constant range of dynamical gradients. Here, we investigate the effect of film/substrate interactions on the film dynamics by varying the TPD/substrate interfacial interactions. We show that thin TPD films with thicknesses below ∼60 nm show a smaller extent of T _g reduction and enhanced dynamics when supported on a near-neutral substrate (wetting) compared to a weakly interacting (dewetting) substrate. However, the ∼30 nm length scale, where the activation energy significantly reduces from its bulk value as measured by the onset of the glass transition remains unchanged. Coarse-grained molecular dynamics simulation also shows a narrowing in the range of relaxation times once the thickness is sufficiently reduced for the two interfaces to dynamically correlate, consistent with previous work. These results suggest that the length-scale for the correlated dynamics is independent of interfacial interactions and the polymeric nature of the film and may originate from the bulk glass properties.

Reorientation Kinetics of Local Conformation of Polyisoprene at Substrate Interface

The performance of a polymer composite material, in which inorganic fillers are dispersed, is closely related to the aggregation states and dynamics of polymer chains at the interface with the filler. In this study, the local conformation of polyisoprene (PI) at a quartz substrate interface was studied as a model system for the rubber/filler composite material. PI films were prepared from a toluene solution onto quartz substrates by a spin-coating method. Sum-frequency generation spectroscopy revealed that the local conformation of PI chains at the quartz interface depended on the spinning rate. The tilt angle of methyl groups increased with the rotational speed, probably due to the centrifugal force applied to chains and probably also the evaporation rate of the solvent during the solidification process. This result indicates that the interfacial orientation of PI chains can remain even at room temperature, which is 87 K higher than the bulk glass transition temperature (T_g^b). The interfacial orientation disappeared at a temperature approximately 120 K higher than T_g^b.

A comparison of SERS and MEF of rhodamine 6G on a gold substrate

Multilayer films of rhodamine 6G can act as its own dielectric layer on gold surfaces to enhance emission spectra.

The architecture of the adsorbed layer at the substrate interface determines the glass transition of supported ultrathin polystyrene films

To elucidate the mechanism underlying the effect of polymer/solid interfacial interactions on the dynamics of thin polymer films, the glass transition of thin end-functionalized polystyrene films supported on SiO₂-Si, such as proton-terminated PS (PS-H), α,ω-dicarboxy-terminated PS (PS-COOH), and α,ω-dihydroxyl-terminated PS (PS-OH), was investigated. All the PS films exhibited a substantial depression in T_g with decreasing film thickness, while the extent of such depression was strongly dependent on the chemical structure of the end groups and molecular weights. It was found that T - T of the various PS films increased linearly with increasing h_ads/R_g, in which h_ads is the thickness of the interfacial adsorbed layer and R_g is the radius of gyration of PS. The h_ads/R_g is a direct reflection of the macromolecular chain conformation within the adsorbed layer which was affected by its end groups and molecular weights. These findings are in line with the work of Napolitano, and present direct experimental evidence.

Interfacial Diffusion and Bonding in Multilayer Polymer Films: A Molecular Dynamics Simulation

As a stacked form of ultrathin polymer films, multilayer nanostructures are of great interest in various applications. Coarse-grained molecular dynamics simulations were carried out to understand the behaviors of interfacial diffusion and bonding of multilayer polymer films. We found two obvious stages for the interfacial diffusion of polymers in the multilayer film, and it is 3 times faster in the first stage than in the second one due to the evolution of molecular conformations. The polymers near the interfaces have an in-plane mobility much higher than the out-of-plane one. The strength of interfacial bonding has been characterized by the fast tensile stress-strain curve along the normal direction. It shows multiple yielding points for the multilayer polymer films, which is distinct from the tensile behavior of the bulk. The ultimate tensile stress (UTS) and corresponding separating strain, surprisingly, do not necessarily increase with diffusion time. Because of the dramatic molecular rotation and extension during the first stage of interfacial diffusion, the interlayer interpenetration is nonuniformly distributed in the plane of the interface. Such a nonuniform distribution may be one of the reasons for the decrease of the UTS and separating strain.

Effect of geometric curvature on vitrification behavior for polymer nanotubes confined in anodic aluminum oxide templates

The glass transition behavior of polystyrene (PS) nanotubes confined in cylindrical alumina nanopores was studied as a function of pore diameter (d) and polymer tube thickness (δ). Both the calorimetric glass transition temperature and the microstructure measured by a nonradiative energy transfer method indicated that the polymer nanotube, or concave polymer thin film, exhibited significant differences in vitrification behavior compared to the planar one. A closer interchain proximity and an increased T_{g} were observed for polymer nanotubes with respect to the bulk polymer. T_{g} for polymer nanotubes was primarily dependent on the curvature radius d of the template, while it was less dependent on the thickness δ of the PS tube wall in the range of 11-23 nm. For small nanotubes (d=55nm), the T_{g} increased as high as 18 °C above the bulk value. This vitrified property reverted back to the bulk value when the substrate was chemically removed, which indicated the crucial importance of the interfacial effect imposed by the hard wall with a concave geometry.

Sensitive and reliable detection of glass transition of polymers by fluorescent probes based on AIE luminogens

A sensitive and reliable approach for the detection of the glass transition of polymers using AIE luminogens as fluorescent probes was reported.