Stabilization of Chitosan Aggregates at the Nanoscale in Solutions in Carbonic Acid

Coating based on chitosan/vancomycin nanoparticles: Patterns of formation in a water-carbon dioxide biphase system and in vivo stability

The patterns of formation of chitosan nanoparticles doped with vancomycin and coatings based on them in carbonate solutions have been investigated for the first time in this study. Using a technique of radioactive indicators, it was found that at a CO2 pressure of 30 MPa, the yield of the nanoparticles was ∼85 %, and a maximum antibiotic encapsulation efficiency of ∼30 % was achieved. By spectrophotometric and high-resolution microscopy, it was found that the coating of stabilized xenopericardial tissue of bioprosthetic heart valve, based on chitosan nanoparticles doped with vancomycin with a zeta potential |ζ| ∼20 mV completely covers collagen fibers by depositing about 60 nm nanoparticles onto them under direct deposition from carbonic acid at a pressure of 30 MPa CO2. The coating preserves the mechanical strength characteristics of collagen tissue and completely suppresses the growth of S. aureus pathogenic biofilm. This is consistent with the observed increase in antibiotic release of 15 % when the medium was acidified. Histological study demonstrated that the structure of pericardial tissues was not significantly altered by the deposition nanoparticles from carbonic acid. It was found that the rate of biodegradation of polymers and vancomycin in the coating differs by half (16 weeks for the rat model). A significantly lower degradation rate of antibiotics (∼50 % of vancomycin total remaining mass and ∼25 % of chitosan) was associated with its reliable encapsulation into nanoparticles.

Structure, the energy, sorption and biological properties of chiral salts of chitosan with l- and d-ascorbic acid

The influence of l- and d-ascorbic acid diastereomers on the structure, supramolecular ordering, energy, sorption and biological properties of heterochiral (D-L) and homochiral (D-D) salt complexes of chitosan (d-glucan)-acid was studied. The thermal effect of dissolving chitosan in l-ascorbic acid and the protonation degree of (D-L)-salts were lower than those in the medium of the d-isomer. Homochiral (D-D) salts, in contrast to heterochiral (D-L) ones, are distinguished by a more developed system of intermolecular and intramolecular contacts, a more ordered and equilibrium supramolecular organization of macrochains, a higher crystallinity degree, and a smaller amount of crystallization water. The sorption isotherms of chiral salts were approximated by the thermal equation of sorption and the superposition of the Langmuir and Flory-Huggins isotherms. Significant differences were found in the limiting value and energy of sorption, the constant of adsorption equilibrium, the limiting sorption capacity of the localized mode of water, and the Gibbs mixing energy. Biotesting on non-vascular (Scenedesmus quadricauda) and vascular eukaryotes (Linum usitatissimum) revealed the growth-stimulating effect of the D-D salts. The obtained results confirm our hypothesis of the homochiral salt complexes d-glucan-d-ascorbic acid best corresponding to the principles of the functional organization of biological objects.

A Novel Hydrophilic, Antibacterial Chitosan-Based Coating Prepared by Ultrasonic Atomization Assisted LbL Assembly Technique

To explore the potential applicability of chitosan (CTS), we prepared aldehyde chitosan (CTS-CHO) with chitosan and sodium periodate via oxidation reaction and then a chitosan-based hydrophilic and antibacterial coating on the surface of poly (lactic acid) (PLA) film was developed and characterized. The oxidation degree was determined by Elemental analyser to be 12.53%, and a Fourier transform infrared spectroscopy was used to characterize the structure of CTS-CHO. It was evident that CTS-CHO is a biocompatible coating biomaterial with more than 80% cell viability obtained through the Live/Dead staining assay and the alamarBlue assay. The hydrophilic and antibacterial CTS-CHO coating on the PLA surface was prepared by ultrasonic atomization assisted LbL assembly technique due to Schiff's base reaction within and between layers. The CTS-CHO coating had better hydrophilicity and transparency, a more definite industrialization potential, and higher antibacterial activity at experimental concentrations than the CTS coating. All of the results demonstrated that the ultrasonic atomization-assisted LbL assembly CTS-CHO coating is a promising alternative for improving hydrophilicity and antibacterial activity on the PLA surface. The functional groups of CTS-CHO could react with active components with amino groups via dynamic Schiff's base reaction and provide the opportunity to create a drug releasing surface for biomedical applications.

Water Saturated with Pressurized CO2 as a Tool to Create Various 3D Morphologies of Composites Based on Chitosan and Copper Nanoparticles

Methods for creating various 3D morphologies of composites based on chitosan and copper nanoparticles stabilized by it in carbonic acid solutions formed under high pressure of saturating CO2 were developed. This work includes a comprehensive analysis of the regularities of copper nanoparticles stabilization and reduction with chitosan, studied by IR and UV-vis spectroscopies, XPS, TEM and rheology. Chitosan can partially reduce Cu2+ ions in aqueous solutions to small-sized, spherical copper nanoparticles with a low degree of polydispersity; the process is accompanied by the formation of an elastic polymer hydrogel. The resulting composites demonstrate antimicrobial activity against both fungi and bacteria. Exposing the hydrogels to the mixture of He or H2 gases and CO2 fluid under high pressure makes it possible to increase the porosity of hydrogels significantly, as well as decrease their pore size. Composite capsules show sufficient resistance to various conditions and reusable catalytic activity in the reduction of nitrobenzene to aniline reaction. The relative simplicity of the proposed method and at the same time its profound advantages (such as environmental friendliness, extra purity) indicate an interesting role of this study for various applications of materials based on chitosan and metals.

Toward In-Field Determination of Nitrate Concentrations Via Diffusive Gradients in Thin Films-Incorporation of Reductants and Color Reagents

Diffusive gradients in thin films (DGTs) have been established as useful tools for the determination of nitrate, phosphate, trace metals, and organic concentrations. General use of DGTs, however, is limited by the subsequent requirement for laboratory analysis. To increase the uptake of DGT as a tool for routine monitoring by nonspecialists, not researchers alone, methods for in-field analysis are required. Incorporation of color reagents into the binding layer, or as the binding layer, could enable the easy and accurate determination of analyte concentrations in-field. Here, we sought to develop a chitosan-stabilized silver nanoparticle (AuNP) suspension liquid-binding layer which developed color on exposure to nitrite, combined with an Fe(0)-impregnated poly-2-acrylamido-2-methyl-1-propanesulfonic acid/acrylamide copolymer hydrogel [Fe(0)-p(AMPS/AMA)] for the reduction of nitrate. The AuNP-chitosan suspension was housed in a 3D designed and printed DGT base, with a volume of 2 mL, for use with the standard DGT solution probe caps. A dialysis membrane with a molecular weight cutoff of <15 kDa was used, as part of the material diffusion layer, to ensure that the AuNP-chitosan did not diffuse through to the bulk solution. This synthesized AuNP-chitosan provided quantitative nitrite concentrations (0 to 1000 mg L-1) and masses (145 μg) in laboratory-based color development studies. An Fe(III)-impregnated poly-2-acrylamido-2-methyl-1-propanesulfonic acid/acrylamide copolymer hydrogel [Fe(III)-p(AMPS/AMA)] was developed (10% AMPS, and 90% AMA), which was treated with NaBH4 to form an Fe(0)-p(AMPS/AMA) hydrogel. The Fe(0)-p(AMPS/AMA) hydrogel quantitatively reduced nitrate to nitrite. The total nitrite mass produced was ∼110 μg, from nitrate. The diffusional characteristics of nitrite and nitrate through the Fe(III)-p(AMPS/AMA) and dialysis membrane were 1.40 × 10-5 and 1.40 × 10-5 and 5.05 × 10-6 and 5.15 × 10-6 cm2 s-1 at 25 °C respectively. The Fe(0)-hydrogel and AuNP-chitosan suspension operated successfully in laboratory tests individually; however, the combined AuNP-chitosan suspension and Fe(0)-hydrogel DGT did not provide quantitative nitrate concentrations. Further research is required to improve the reaction rate of the AuNP-chitosan nitrite-binding layer, to meet the requirement of rapid binding to operate as a DGT.

Synthesis of chitosan/TCN nanocomposites with the carbon dioxide assisted phase inversion

The chitosan (CS)/bis(2-hydroxyethyl)methyl tallow ammonium modified montmorillonite (TCN) nanocomposites are synthesized by the phase inversion procedure via the assistance of carbon dioxide (CO₂). The viscosity of CS/formic acid solution is reduced with the incorporation of CO₂ owing to the formation of carbamic acid. However, the incorporation of TCN promotes the viscosity of CS solution due to the interaction between TCN and carbamic acid. The morphology of CS/TCN nanocomposites is studied by scanning electron microscopy (SEM), where the surface of the membrane is dense and non-porous. The microstructure of the synthesized CS/TCN composite is further investigated by attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectra, X-ray diffraction (XRD), differential scanning calorimetry (DSC), and transmission electron microscopy (TEM). It is found that the incorporation of TCN without the presence of CO₂ disturbs the crystallization of CS. Interestingly, the melting enthalpy of the CS/TCN composite is notably increased with the introduction of CO₂, demonstrating that the interaction between the TCN and carbamic acid enhances the formation of CS crystals. XRD and TEM results show that this interaction is able to promote the homogeneous distribution of TCN in the nanoscale with the non-exfoliated form, enhancing the mechanical properties of the synthesized nanocomposites. In particular, the synthesized CS/TCN nanocomposites with the assistance of CO₂ present exceptional mechanical properties, where the tensile strength (65.82 MPa) and Young's modulus (3512.48 MPa) are twice as high as that of the CO₂ free system.

Synthesis of chitosan/silver nanocomposites by phase inversion with the assistance of carbon dioxide

Carbon dioxide (CO₂) assisted synthesis of water-soluble silver nanoparticle with a narrow particle size distribution is reported here based on the phase-inversion procedure. Bio-derived chitosan (CS) is used to stabilize the metal nanoparticles according to its abundant functional groups. Formic acid is employed as both a solvent (for the polymer) and a reductant for in-situ reducing the silver precursor along with the solvent evaporation. CO₂ is utilized to combine with the amino groups of CS, reducing the viscosity of chitosan/formic acid solution and limiting the formation of hydrogen bonds. This promotes the stabilization and reduction efficiency of silver nanoparticles. In particular, 100% of Ag metal nanoparticles with the size of 7.5 ± 2.3 nm is successfully synthesized with the assistance of CO₂. Interestingly, the synthesized CS/Ag nanocomposites are water-soluble owing to the formation of carbamate groups. This water-soluble silver nanoparticle presents an exceptional performance in the selective reduction of 4-nitrophenol, where the turnover frequency (TOF = 599 h^-1) is even double with respect to the CO₂ free system.

Chitosan-based recyclable composite aerogels for the photocatalytic degradation of rhodamine B

TiO₂ based photocatalyst with sufficient reusability for the degradation of water pollutants remains a challenge. Here, we report a composite chitosan-based aerogel containing TiO₂ nanoparticles, multiwalled carbon nanotubes and layered silicate rectorite with sufficient mechanical strength for Rhodamine B degradation. The aerogels with homogeneous oriented lamellar structure were successfully prepared via a unidirectional freeze-casting technique. As-prepared aerogels showed specific surface area of 84.59 m²/g. The addition of rectorite and carbon nanotubes accelerated the photodegradation and rectorite significantly enhanced the overall mechanical performance. Rapid degradation of rhodamine B (95% in 100 min) was observed on aerogels with 2 wt% and 4 wt% of rectorite. After 3 cycles, 75% degradation of Rhodamine B was achieved with CTCR4, confirming its reusability. Thus, the composite chitosan aerogels show high photocatalytic degradation efficiency towards Rhodamine B during cycle use.

Microstructure and Mechanical Strength Properties of Chitosan Sponges Obtained from Polymer Solutions in Carbonic Acid

Abstract

Polymer sponges based on chitosan are first obtained from chitosan solutions in carbonic acid and gels based on these solutions crosslinked by a noncytotoxic agent of natural origin, genipin. A comparative analysis of the structure and mechanical strength properties of sponges prepared from chitosan solutions in carbonic and acetic acids is carried out. It is shown that the addition of genipin in an amount of ~2 wt % to a chitosan solution in carbonic acid leads to a decrease in the average pore size by ~2.5 times and a significant increase in the strength characteristics of the material in comparison with the sponge prepared without genipin.

Green approach for fabrication of bacterial cellulose-chitosan composites in the solutions of carbonic acid under high pressure CO2

The functionalization of the bacterial cellulose (BC) surface with a chitosan biopolymer to expand the areas of possible applications of the modified BC is an important scientific task. The creation of such composites in the carbonic acid solutions that were performed in this work has several advantages in terms of being biocompatible and eco-friendly. Quantitative analysis of chitosan content in the composite was conducted by tritium-labeled chitosan radioactivity detection method and this showed three times increased chitosan loading. Different physicochemical methods showed successful incorporation of chitosan into the BC matrix and interaction with it through hydrogen bonds. Microscopy results showed that the chitosan coating with a thickness of around 10 nm was formed in the bulk of BC, covering each microfibril. It was found that the inner specific surface area increased 1.5 times on deposition of chitosan from the solutions in carbonic acid.

Probing the Molecular Interactions of Chitosan Films in Acidic Solutions with Different Salt Ions

Understanding the interaction mechanisms of chitosan films plays a central role in a wide range of its applications, such as bioadhesive, drug delivery, wound healing, tissue engineering, and wastewater treatment for heavy metal ions. Here, we investigated the molecular interactions between chitosan films in acidic solutions with different salt ions using a surface forces apparatus (SFA). The results showed that chitosan can be adsorbed to mica surfaces by electrostatic interaction under acidic conditions. The force measurements demonstrated that the interactions depend on the salt types, concentrations, and contact time. With the addition of 1 mM LaCl3 and NaCl into the acetic acid (HAc) buffer solution, the cohesion between chitosan films enhanced by about 45% and 20%, respectively, after a contact time of 60 min. The enhanced cohesion induced by the combination of partly intermolecular complexation formation in a bridge model and conformation adjustment of chitosan under contact time in 1 mM LaCl3 solution. However, the cohesion reduced rapidly and even disappeared when the salt concentration increased to 10 mM and 100 mM. We proposed that the cross-linked structures of chitosan mainly contribute to the significant reduction of chitosan cohesion in LaCl3 solution. In comparison, the decrease in cohesion capacity in NaCl solution mainly results from the enhanced hydration effect. Our findings may provide insights into the interaction mechanisms of chitosan films under nanoconfinement in acidic conditions and suggestions for the development of chitosan-based materials.

Diminishing Cohesion of Chitosan Films in Acidic Solution by Multivalent Metal Cations

Chitosan is a natural polymer with good biocompatibility, biodegradability, and bioactivity that has great potential for biomedical and industrial applications. Like other natural sugar-based polymers, chitosan molecules own versatile adhesion abilities to bind with various surfaces, owing to multiple functional moieties contained in the chain. To develop the promising biomaterials based on the chitosan chemistry, it is fundamentally important to figure out its adhesion mechanism under a certain condition, which leaves us numbers of open questions. In this work, we characterized the chitosan films adsorbed on a mica substrate in acidic solution and investigated the effects of multivalent salts on the cohesive behaviors of the films by means of the surface forces apparatus. The results showed that the cohesion capacities of chitosan films were reduced to around 30% of their original states after the addition of 10^-7 M LaCl₃ into 150 mM acetic acid, which could be partially recovered by holding the films at the contact position for a longer time. Surprisingly, the cohesion loss in the films exhibited the dependence on the properties of the metal cations including valance and concentration. The topography of the chitosan-coated surface also showed obvious aggregation in the presence of submicromolar of the salts. Here, we attributed these phenomena regarding cohesion loss to the mechanisms involved in the absorption of metal cations by the chitosan chains, which not only consumed the binding sites but also induced conformation change in the polymer network. Our findings may offer a suggestion for the production of chitosan-based materials to notice the potential impacts of ultralow concentrated salts that are usually neglected even under acidic conditions.

Interpolyelectrolyte Complex Dissociation vs Polyelectrolyte Desorption from Oppositely Charged Surface upon Salt Addition

The structure of complexes formed by oppositely charged polyelectrolytes and adsorbed layers on charged surfaces is sensitive to low-molecular-weight salt. Furthermore, if the concentration exceeds some threshold value, the complexes and adsorbed chains can be "dissolved". This is due to the screening of the electrostatic interactions between charged units. In the current paper, we perform a comparative analysis of "dissolution" (dissociation) of complexes and layers upon addition of salt. For this, the conventional Brownian dynamics of computer simulations is used. We demonstrate that the complex based on linear chains dissociates at lower salt concentration than that required for desorption of equivalent chains from an oppositely charged surface. The physical reason is the difference in the symmetry of the electric field, which binds the chains into the complex (layer). In the salt-free regime, the intensity of the electric field (and attractive force) between two linear chains decays with the distance R between them, like for two spherical objects, ∼R^-2, if R is bigger than the characteristic size of the chain. On the contrary, the attractive force of the chain to the infinite surface does not depend on the distance to the surface (the electric field is constant). Therefore, if attractive forces in the condensed states of the two systems are equal, one needs to add more salt to screen the constant force than the decaying one. The computer simulation results on the adsorption of the chains were compared with the experimental data obtained for adsorption of cationic poly(4-vinylpyridine) on the surface of anionic liposomes. Good quantitative agreement was achieved.

Dissolution of chitosan nanocrystals in aqueous media of different acidity. Molecular dynamic study

The process of dissolution of chitosan nanocrystals with molecular mass of polymer up to 12.8 kDa in aqueous media of various pH was studied by molecular dynamic simulations with the use of the improved force field GROMOS 56A_{CARBO_CHT} specially developed for the chitosan polymers description. The effect of the media acidity and polymer molecular weight on the dissolution process kinetics has been studied and the regression expressions for kinetic parameters were established. The calculated solution viscosity, Mark-Houwink-Sakurada equation parameters, and pH values of the dissolution beginning are in good agreement with the available experimental data. The uniform/non-uniform distribution of protonated amino groups and hydrogen bonds along the polymeric chains is found to be of key importance parameter for the dissolution process which can be considered as a criterion of dissolution ability.

An anionic shell shields a cationic core allowing for uptake and release of polyelectrolytes within core-shell responsive microgels

To realize carriers for drug delivery, cationic containers are required for anionic guests. Nevertheless, the toxicity of cationic carriers limits their practical use. In this study, we investigate a model system of polyampholyte N-isopropylacrylamide (NIPAM)-based microgels with a cationic core and an anionic shell to study whether the presence of a negative shell allows the cationic core to be shielded while still enabling the uptake and release of the anionic guest polyelectrolytes. These microgels are loaded with polystyrene sulfonate of different molecular weights to investigate the influence of their chain length on the uptake and release process. By means of small-angle neutron scattering, we evaluate the spatial distribution of polystyrene sulfonate within the microgels. The guest molecules are located in different parts of the core-shell microgels depending on their size. By combining these scattering results with UV-vis spectroscopy, electrophoretic mobility and potentiometric titrations we gain complementary results to investigate the uptake and release process of polyelectrolytes in polyampholyte core-shell microgels. Moreover, Brownian molecular dynamic simulations are performed to compare the experimental and theoretical results of this model. Our findings demonstrate that the presence of a shell still enables efficient uptake of guest molecules into the cationic core. These anionic guest molecules can be released through an anionic shell. Furthermore, the presence of a shell enhances the stability of the microgel-polyelectrolyte complexes with respect to the cationic precursor microgel alone.

Modification of 56ACARBO force field for molecular dynamic calculations of chitosan and its derivatives

The GROMOS 56A_CARBO force field for the description of carbohydrates was modified for calculations of chitosan (poly-1,4-(N-acetyl)-β-D-glucopyranosamine-2) with protonated and non-protonated amino groups and its derivatives. Additional parameterization was developed on the basis of quantum chemical calculations. The modified force field (56A_{CARBO_CHT}) allows performing the molecular dynamic calculations of chitosans with different degrees of protonation corresponding to various acidity of medium. Test calculations of the conformational transitions in the chitosan rings and polymeric chains as well as the chitosan nanocrystal dissolution demonstrate good agreement with experimental data. Graphical abstract The GROMOS 56A_{CARBO_CHT} force field allows performing the molecular dynamic calculations of chitosans with different types of amio-group: free, protonated, substituted.

Chitosan coatings with enhanced biostability in vivo

In this article, we study the stability of chitosan coatings applied on glutaraldehyde-stabilized bovine pericardium when exposed to biodegradation in vivo in the course of model subcutaneous tests on rats. The coatings were deposited from carbonic acid solutions, that is, H₂ O saturated with CO₂ at high pressure. Histological sections of treated pericardium samples demonstrated that the structure of pericardial connective tissues was not significantly altered by the coating application method. It was revealed that the dynamics of biodegradation depended on the total mass of chitosan applied as well as on the DDA of chitosan used. As long as the amount of chitosan did not exceed a certain threshold limit, no detectable degradation occurred within the time of the tests (12 weeks for the rat model). For higher chitosan amounts, we detected a ∼20% reduction of the mass after the in vivo exposition. The presumed mechanism of such behavior is discussed. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 106B: 270-277, 2018.

Formation of Easy-to-Recover Polystyrene-block-Poly(4-vinylpyridine) Micelles Decorated with Pd Nanoparticles in Solutions of Self-Neutralizing Carbonic Acid

It was found out that block copolymers of polystyrene and poly(4-vinylpyridine) with comparable lengths of blocks could be dissolved in a high-pressure reactor containing water phase saturated with carbon dioxide under high pressure at room temperature. This rather effective dissolution occurs due to a protonation of P4VP nitrogen-containing groups together with a plasticization of the polymer material to be dissolved by a compressed dense CO₂ being contained in the autoclave. The selected block copolymers form rather monodispersed micelles with well-defined and reproducible spherical geometry. They apparently have a hydrophobic polystyrene core and a polycationic poly-4-vinylpyridine corona. The obtained micelles were characterized by various techniques such as DLS, AFM, TEM, and SEM. Further, it was revealed that the corona of such micelles could be decorated with Pd nanoparticles having the diameter around 3 nm.