Measurement of the adhesion force between carbon nanotubes and a silicon dioxide substrate

Adhesion of Single-Walled Carbon Nanotube Thin Films with Different Materials

Single-walled carbon nanotubes (SWCNTs) possess extraordinary physical and chemical properties. Thin films of randomly oriented SWCNTs have great potential in many opto-electro-mechanical applications. However, good adhesion of SWCNT films with a substrate material is pivotal for their practical use. Here, for the first time, we systematically investigate the adhesion properties of SWCNT thin films with commonly used substrates such as glass (SiO₂), indium tin oxide (ITO), crystalline silicon (C-Si), amorphous silicon (a-Si:H), zirconium oxide (ZrO₂), platinum (Pt), polydimethylsiloxane (PDMS), and SWCNTs for self-adhesion using atomic force microscopy. By comparing the results obtained in air and inert Ar atmospheres, we observed that the surface state of the materials greatly contributes to their adhesion properties. We found that the SWCNT thin films have stronger adhesion in an inert atmosphere. The adhesion in the air can be greatly improved by a fluorination process. Experimental and theoretical analyses suggest that adhesion depends on the atmospheric conditions and surface functionalization.

Stretching and Breaking of Ultrathin 2D Hybrid Organic-Inorganic Perovskites

Two-dimensional (2D) hybrid organic-inorganic perovskites (HOIPs) are recent members of the 2D materials family with wide tunability, highly dynamic structural features, and excellent physical properties. Ultrathin 2D HOIPs and their heterostructures with other 2D materials have been exploited for study of physical phenomena and device applications. The in-plane mechanical properties of 2D ultrathin HOIPs are critical for understanding the coupling between mechanical and other physical fields and for integrated devices applications. Here we report the in-plane mechanical properties of ultrathin freestanding 2D lead iodide perovskite membranes and their dependence on the membrane thickness. The in-plane Young's moduli of 2D HOIPs are smaller than that of conventional covalently bonded 2D materials. As the thickness increases from monolayer to three-layer, both the Young's modulus and breaking strength decrease, while three-layer and four-layer 2D HOIPs have almost identical in-plane mechanical properties. These thickness-dependent mechanical properties can be attributed to interlayer slippage during deformation. Our results show that ultrathin 2D HOIPs exhibit outstanding breaking strength/Young's modulus ratio compared to many other widely used engineering materials and polymeric flexible substrates, which renders them suitable for application into flexible electronic devices.

Topological Transitions and Fractional Charges Induced by Strain and a Magnetic Field in Carbon Nanotubes

We show that carbon nanotubes (CNT) can be driven through a topological phase transition using either strain or a magnetic field. This can naturally lead to Jackiw-Rebbi soliton states carrying fractionalized charges, similar to those found in a domain wall in the Su-Schrieffer-Heeger model, in a setup with a spatially inhomogeneous strain and an axial field. Two types of fractionalized states can be formed at the interface between regions with different strain: a spin-charge separated state with integer charge and spin zero (or zero charge and spin ±ℏ/2), and a state with charge ±e/2 and spin ±ℏ/4. The latter state requires spin-orbit coupling in the CNT. We show that in our setup, the precise quantization of the fractionalized interface charges is a consequence of the symmetry of the CNT under a combination of a spatial rotation by π and time reversal.

Strongly Coupled Nanotube Electromechanical Resonators

Coupling an electromechanical resonator with carbon-nanotube quantum dots is a significant method to control both the electronic charge and the spin quantum states. By exploiting a novel microtransfer technique, we fabricate two separate strongly coupled and electrically tunable mechanical resonators for the first time. The frequency of the two resonators can be individually tuned by the bottom gates, and in each resonator, the electron transport through the quantum dot can be strongly affected by the phonon mode and vice versa. Furthermore, the conductance of either resonator can be nonlocally modulated by the other resonator through phonon-phonon interaction between the two resonators. Strong coupling is observed between the phonon modes of the two resonators, where the coupling strength larger than 200 kHz can be reached. This strongly coupled nanotube electromechanical resonator array provides an experimental platform for future studies of the coherent electron-phonon interaction, the phonon-mediated long-distance electron interaction, and entanglement state generation.

Stick, partial slip and sliding in the plane strain micro contact of two elastic bodies

The plane strain problem of a curved elastic body pressed against an elastic half-space is considered. The effect of adhesion is included through the use of surface energy in a manner similar to the well-known JKR theory for spherical contacts. The compressive normal force is held constant while a tangential force is gradually increased from zero. The contact is characterized by complete stick up to a critical value of the tangential force when there is a transition either directly to complete sliding or to a partial slip state in which a central stick region is surrounded by two slip regions. In the latter case, at a finite value of the stick zone width, a second critical condition exists at which there is a transition from partial slip to complete sliding. This behaviour is determined for a range of dimensionless values of the work of adhesion, the assumed constant shear stress during slip/sliding and the initial compressive load.

Investigation of interfacial adhesion between the top ends of carbon nanotubes

Understanding the interfacial forces of carbon nanotubes (CNTs) is fundamental to the development of electromechanical systems based on the contact of CNTs. However, experimental studies on the adhesion properties between CNTs are scarce despite the remarkable contact quality of CNTs. Here, we present an experimental investigation of the adhesion between the top ends of aligned, self-adjusted CNTs using a CNT-integrated microelectromechanical actuator. The pull-out and pull-in behaviors of the contact as a function of the applied force by the actuator are precisely identified by measuring the contact resistance between the CNTs. The adhesion between the top ends of individual CNTs is extracted from the measured adhesive strength between the CNT arrays, and it agrees with the theoretical values of the van der Waals interactions. By exploiting the adhesion of the CNT-to-CNT contact, a programmable and reliable microelectromechanical switching device is demonstrated. Our results offer design strategies for diverse CNT-based nano- and microelectromechanical devices that need repeatable contacting interfaces.

Simultaneous measurement of static and kinetic friction of ZnO nanowires in situ with a scanning electron microscope

A novel method for in situ measurement of the static and kinetic friction is developed and demonstrated for zinc oxide nanowires (NWs) on oxidised silicon wafers. The experiments are performed inside a scanning electron microscope (SEM) equipped with a nanomanipulator with an atomic force microscope tip as a probe. NWs are pushed by the tip from one end until complete displacement is achieved, while NW bending is monitored by the SEM. The elastic bending profile of a NW during the manipulation process is used to calculate the static and kinetic friction forces.

Friction and shear strength at the nanowire-substrate interfaces

The friction and shear strength of nanowire (NW)-substrate interfaces critically influences the electrical/mechanical performance and life time of NW-based nanodevices. Yet, very few reports on this subject are available in the literature because of the experimental challenges involved and, more specifically no studies have been reported to investigate the configuration of individual NW tip in contact with a substrate. In this letter, using a new experimental method, we report the friction measurement between a NW tip and a substrate for the first time. The measurement was based on NW buckling in situ inside a scanning electron microscope. The coefficients of friction between silver NW and gold substrate and between ZnO NW and gold substrate were found to be 0.09-0.12 and 0.10-0.15, respectively. The adhesion between a NW and the substrate modified the true contact area, which affected the interfacial shear strength. Continuum mechanics calculation found that interfacial shear strengths between silver NW and gold substrate and between ZnO NW and gold substrate were 134-139 MPa and 78.9-95.3 MPa, respectively. This method can be applied to measure friction parameters of other NW-substrate systems. Our results on interfacial friction and shear strength could have implication on the AFM three-point bending tests used for nanomechanical characterisation.

Competition of elastic and adhesive properties of carbon nanotubes anchored to atomic force microscopy tips

In this paper we address the mechanical properties of carbon nanotubes anchored to atomic force microscopy (AFM) tips in a detailed analysis of experimental results and exhaustive description of a simple model. We show that volume elastic and surface adhesive forces both contribute to the dynamical AFM experimental signals. Their respective weights depend on the nanotube properties and on an experimental parameter: the oscillation amplitude. To quantify the elastic and adhesive contributions, a simple analytical model is used. It enables analytical expressions of the resonance frequency shift and dissipation that can be measured in the atomic force microscopy dynamical frequency modulation mode. It includes the nanotube adhesive contribution to the frequency shift. Experimental data for single-wall and multi-wall carbon nanotubes compare well to the model predictions for different oscillation amplitudes. Three parameters can be extracted: the distance necessary to unstick the nanotube from the surface and two spring constants corresponding to tube compression and to the elastic force required to overcome the adhesion force.

Strain tuning of the photocurrent spectrum in single-wall carbon nanotubes

The effect of uniaxial strain on the photocurrent spectrum of semiconducting single-wall carbon nanotubes is measured. The energy of the lowest-lying free electron transition is observed to shift with strain as predicted by a simple noninteracting model. The higher-order transitions also shift with strain, but being excitonic, their strain dependence differs from the predictions for the free carrier states. An anomalous photocurrent increase is also observed near the ground-state transition and is attributed to the formation of optically active defect states within the nanotube band gap.