In situ raman measurements of suspended individual single-walled carbon nanotubes under strain

In situ multiproperty measurements of individual nanomaterials in SEM and correlation with their atomic structures

The relationship between property and structure is one of the most important fundamental questions in the field of nanomaterials and nanodevices. Understanding the multiproperties of a given nano-object also aids in the development of novel nanomaterials and nanodevices. In this paper, we develop for the first time a comprehensive platform for in situ multiproperty measurements of individual nanomaterials using a scanning electron microscope (SEM). Mechanical, electrical, electromechanical, optical, and photoelectronic properties of individual nanomaterials, with lengths that range from less than 200 nm to 20 μm, can be measured in situ with an SEM on the platform under precisely controlled single-axial strain and environment. An individual single-walled carbon nanotube (SWCNT) was measured on the platform. Three-terminal electronic measurements in a field effect transistor structure showed that the SWCNT was semiconducting and agreed with the structure characterization by transmission electron microscopy after the in situ measurements. Importantly, we observed a bandgap increase of this SWCNT with increasing axial strain, and for the first time, the experimental results quantitatively agree with theoretical predictions calculated using the chirality of the SWCNT. The vibration performance of the SWCNT, a double-walled CNT, and a triple-walled CNT were also studied as a function of axial strain, and were proved to be in good agreement with classical beam theory, although the CNTs only have one, two, or three atomic layers, respectively. Our platform has wide applications in correlating multiproperties of the same individual nanostructures with their atomic structures.

Investigation of temperature dependent multi-walled nanotube G and D doublet using pseudo-Voigt functions

A pseudo-Voigt (PV) function is used as a representation of the Stoke's phonon frequency distributions for a multi-walled nanotube (MWNT) composite G and D doublet. Variable peak assignments with the PV function have been shown to enhance the resolution of these bands commonly used for characterization of carbon nanotube (CNT) composites. The peak assignment study was applied to an in-situ temperature experiment where the addition of new sub-bands in the G and D doublet was determined to reduce the uncertainty of the Raman characteristics. Fitting the spectrum with five pseudo-Voigt bands was concluded to give the most consistent results, producing the lowest uncertainty values for G-peak position (νG) and D/G intensity ratio.

In situ three-dimensional reciprocal-space mapping during mechanical deformation

Mechanical deformation of a SiGe island epitaxically grown on Si(001) was studied by a specially adapted atomic force microscope and nanofocused X-ray diffraction. The deformation was monitored during in situ mechanical loading by recording three-dimensional reciprocal-space maps around a selected Bragg peak. Scanning the energy of the incident beam instead of rocking the sample allowed the safe and reliable measurement of the reciprocal-space maps without removal of the mechanical load. The crystal truncation rods originating from the island side facets rotate to steeper angles with increasing mechanical load. Simulations of the displacement field and the intensity distribution, based on the finite-element method, reveal that the change in orientation of the side facets of about 25° corresponds to an applied pressure of 2-3 GPa on the island top plane.

Invited review article: combining scanning probe microscopy with optical spectroscopy for applications in biology and materials science

This is a comprehensive review of the combination of scanning probe microscopy (SPM) with various optical spectroscopies, with a particular focus on Raman spectroscopy. Efforts to combine SPM with optical spectroscopy will be described, and the technical difficulties encountered will be examined. These efforts have so far focused mainly on the development of tip-enhanced Raman spectroscopy, a powerful technique to detect and image chemical signatures with single molecule sensitivity, which will be reviewed. Beyond tip-enhanced Raman spectroscopy and/or topography measurements, combinations of SPM with optical spectroscopy have a great potential in the characterization of structure and quantitative measurements of physical properties, such as mechanical, optical, or electrical properties, in delicate biological samples and nanomaterials. The different approaches to improve the spatial resolution, the chemical sensitivity, and the accuracy of physical properties measurements will be discussed. Applications of such combinations for the characterization of structure, defects, and physical properties in biology and materials science will be reviewed. Due to the versatility of SPM probes for the manipulation and characterization of small and/or delicate samples, this review will mainly focus on the apertureless techniques based on SPM probes.

Correlation between droplet-induced strain actuation and voltage generation in single-wall carbon nanotube films

In this paper, a method of strain actuation of single-walled carbon nanotube (SWNT) films using droplets is examined, and the physical origin of an open-circuit voltage (Voc)-observed across the film during this process-is explored. We demonstrate that droplet actuation is driven by the formation of a capillary bridge between the suspended SWNT films and the substrates, which deforms the films by wetting forces during evaporation. The induced strain is further evaluated and analyzed using dynamic Raman and two-dimensional correlation spectra. Supported by theoretical calculations, our experiments reveal the time and strain dependency of the capillary bridge's midpoint directional movement. This relationship is applied to display the correlation between the induced strain and the measured Voc.

Influence of external force on properties and reactivity of disulfide bonds

The mechanochemistry of the disulfide bridge--that is, the influence of an externally applied force on the reactivity of the sulfur-sulfur bond--is investigated by unrestricted Kohn-Sham theory. Specifically, we apply the COGEF (constrained geometry simulates external force) approach to characterize the mechanochemistry of the disulfide bond in three different chemical environments: dimethyl disulfide, cystine, and a 102-atom model of the I27 domain in the titin protein. Furthermore, the mechanism of the thiol-disulfide reduction reaction under the effect of an external force is investigated by considering the COGEF potential for the adduct and transition-state clusters. With the unrestricted Becke-three-parameter-Lee-Yang-Parr (UB3LYP) exchange-correlation functional in the 6-311++G(3df,3pd) orbital basis, the rupture force of dimethyl disulfide is 3.8 nN at a disulfide bond elongation of 35 pm. The interaction with neighboring groups and the effect of conformational rigidity of the protein environment have little influence on the mechanochemical characteristics. Upon stretching, we make the following observations: the diradical character of the disulfide bridge increases; the energy difference between the singlet ground state and low-lying triplet state decreases; and the disulfide reduction is promoted by an external force in the range 0.1-0.4 nN. Our model of the interplay between force and reaction mechanism is in qualitative agreement with experimental observations.

Physico-chemical properties of iodine-adsorbed single-walled carbon nanotubes

I2 was adsorbed on single-walled carbon nanotube from ethanol solution at 303 K. The I2 adsorption isotherm was Langmuirian, giving 35 (+/-10) mg g(-1) of the saturated adsorption amount (coverage 0.06-0.09). The I2-adsorption treatment of SWCNT bundles reduced the N2 adsorption amount at 77 K by only 3%; the adsorption amount of supercritical H2 at 77 K was decreased by 30% because of the I2-adsorption treatment, indicating the blocking of interstitial pores by adsorbed I2. These adsorption results indicated the adsorption of I2 molecules in the narrow interstitial pores. The I2-adsorption treatment increases the Raman intensity coming from metallic SWCNTs, and the dc electrical conductivity increased by 15% because of the I2-adsorption treatment, strongly suggesting the presence of charge-transfer interaction between I2 and SWCNTs irrespective of small coverage by I2.