Short-wavelength electroluminescence from single-walled carbon nanotubes with high bias voltage

A light emitter based on practicable and mass-producible polycrystalline graphene patterned directly on silicon substrates from a solid-state carbon source

We developed a procedure for direct patterning of graphene with arbitrary position, size, and shape on silicon substrates from a solid-state carbon source without dry etching processing. Our light emitting graphene devices perform on a par with those based on high crystallinity graphene obtained via mechanical exfoliation or chemical vapor deposition.

We developed a procedure for direct patterning graphene with arbitrary position, size, and shape on Si from a solid-state carbon source without dry etching. Our light emitting devices perform on a par with those based on high crystallinity graphene.

High-speed and on-chip graphene blackbody emitters for optical communications by remote heat transfer

High-speed light emitters integrated on silicon chips can enable novel architectures for silicon-based optoelectronics, such as on-chip optical interconnects, and silicon photonics. However, conventional light sources based on compound semiconductors face major challenges for their integration with a silicon-based platform because of their difficulty of direct growth on a silicon substrate. Here we report ultra-high-speed (100-ps response time), highly integrated graphene-based on-silicon-chip blackbody emitters in the near-infrared region including telecommunication wavelength. Their emission responses are strongly affected by the graphene contact with the substrate depending on the number of graphene layers. The ultra-high-speed emission can be understood by remote quantum thermal transport via surface polar phonons of the substrates. We demonstrated real-time optical communications, integrated two-dimensional array emitters, capped emitters operable in air, and the direct coupling of optical fibers to the emitters. These emitters can open new routes to on-Si-chip, small footprint, and high-speed emitters for highly integrated optoelectronics and silicon photonics.

Integrating graphene with existing silicon technologies may pave the way to compact light sources for optoelectronics and photonics. Here, the authors fabricate graphene-based arrays of blackbody emitters integrated on a silicon chip, operating in the near-infrared region at high speed.

Solid state carbon nanotube device for controllable trion electroluminescence emission

Semiconducting carbon nanotubes (CNTs) have a direct chirality-dependent bandgap and reduced dimensionality-related quantum confinement effects, which are closely related to the performance of optoelectronic devices. Here, taking advantage of the large energy separations between neutral singlet excitons and charged excitons, i.e. trions in CNTs, we have achieved for the first time all trion electroluminescence (EL) emission from chirality-sorted (8,3) and (8,4) CNT-based solid state devices. We showed that strong trion emission can be obtained as a result of localized impact excitation and electrically injected holes, with an estimated efficiency of ∼5 × 10(-4) photons per injected hole. The importance of contact-controlled carrier injection (including symmetric and asymmetric contact configurations) and EL spectral stability for gradually increasing bias were also investigated. The realization of electrically induced pure trion emission opens up a new opportunity for CNT film-based optoelectronic devices, providing a new degree of freedom in controlling the devices to extend potential applications in spin or magnetic optoelectronics fields.

An electrically driven, ultrahigh-speed, on-chip light emitter based on carbon nanotubes

The integration of high-speed light emitters on silicon chips is an important issue that must be resolved in order to realize on-chip or interchip optical interconnects. Here, we demonstrate the first electrically driven ultrafast carbon nanotube (CNT) light emitter based on blackbody radiation with a response speed (1-10 Gbps) that is more than 10(6) times higher than that of conventional incandescent emitters and is either higher than or comparable to that of light-emitting diodes or laser diodes. This high-speed response is explained by the extremely fast temperature response of the CNT film, which is dominated by the small heat capacity of the CNT film and its high heat dissipation to the substrate. Moreover, we experimentally demonstrate 140 ps width pulsed light generation and real-time optical communication. This CNT-based emitter with the advantages of ultrafast response speeds, a small footprint, and integration on silicon can enable novel architectures for optical interconnects, photonic, and optoelectronic integrated circuits.

Electroluminescence from serpentine carbon nanotube based light-emitting diodes on quartz

A light-emitting diode is fabricated and characterized on a semiconducting serpentine CNT which has many parallel segments with identical chirality. Compared with the individual CNT and CNT-film devices, the device with parallel segments shows improvement of an order of magnitude in current, significantly larger electroluminescent intensity, and narrower emission bands. Serpentine nanotubes are an ideal choice for practical applications of CNT-based light sources.

Electroluminescence in aligned arrays of single-wall carbon nanotubes with asymmetric contacts

High quantum efficiencies and low current thresholds are important properties for all classes of semiconductor light emitting devices (LEDs), including nanoscale emitters based on single wall carbon nanotubes (SWNTs). Among the various configurations that can be considered in SWNT LEDs, two terminal geometries with asymmetric metal contacts offer the simplest solution. In this paper, we study, experimentally and theoretically, the mechanisms of electroluminescence in devices that adopt this design and incorporate perfectly aligned, horizontal arrays of individual SWNTs. The results suggest that exciton mediated electron-hole recombination near the lower work-function contact is the dominant source of photon emission. High current thresholds for electroluminescence in these devices result from diffusion and quenching of excitons near the metal contact.