Room temperature electrodeposition of molybdenum sulfide for catalytic and photoluminescence applications

Electrodeposited MoxSyOz/Ni Tribological Coatings

Deposition of molybdenum disulfide (MoS2) coatings using physical vapor deposition (PVD) and mechanical burnishing has been widely assessed for solid lubricants in space applications but still suffers from line-of-sight constraints on complex geometries. Here, we highlight one of the first demonstrations of electrodeposited MoxSyOz and MoxSyOz/Ni thin-film coatings from aqueous solutions of ammonium tetrathiomolybdate for solid lubricant applications and their remarkable ability to provide low coefficients of friction and high wear resistance. Characterization of the coating morphology shows amorphous microstructures with a high oxygen content and cracking upon drying. Even so, electrodeposited MoxSyOz can achieve low steady-state coefficients of friction (μ ∼ 0.05-0.06) and wear rates (2.6 × 10-7 mm3/(N m)) approaching those of physical vapor deposited coatings (2.3 × 10-7 mm3/(N m)). Additionally, we show that adding dopants such as nickel increased the wear rate (7.5 × 10-7 mm3/(N m)) and initial coefficient of friction (μi = 0.23) due to compositional modifications such as dramatic sub-stoichiometry (S/Mo ∼ 1) and expression of a NiOx surface layer, although doping did reduce the degree of cracking upon drying.

Electrochemical and X-ray structural evidence of multiple molybdenum precursor candidates from a reported non-aqueous electrodeposition of molybdenum disulfide

A published report of electrodeposited molybdenum(iv) disulfide microflowers at 100 °C in the ionic liquid N-methyl-N-propylpiperidinium bis(trifluoromethane)sulfonimide (PP13-TFSI) from 1,4-butanedithiol and the concentrated filtrate from a reaction mixture of molybdenum(vi) trioxide and ethylene glycol could not be reproduced reliably, affording numerous uniquely coloured reaction mixtures that precipitated a variety of crystalline molybdenum coordination complexes. Further attempts to use the same two of these filtrates to electrodeposit molybdenum(iv) disulfide from 0.1 M PP13-TFSI in tetrahydrofuran with 1,4-butanedithiol at room temperature were unsuccessful. Various crude reaction mixtures grew crystals of different identity from eight attempts to synthesize the reported molybdenum-precursor. Single crystal X-ray diffraction (SC-XRD) offered insight into a wide range of structural features from four candidate paramagnetic precursor compounds, including a novel organomolybdenum cluster. Electrochemical studies of the various molybdenum-precursor filtrates, ethylene glycol, and 1,4-butanedithiol were conducted in 0.1 M PP13-TFSI in tetrahydrofuran, offering insight into differences between preparations of the molybdenum-precursor and interference between ethylene glycol and 1,4-butanedithiol on platinum working electrodes. Molybdenum(iv) disulfide electrodeposition attempts included cyclic voltammetry and chronoamperometry on platinum and glassy carbon working electrodes, which led to either no deposited material, or molybdenum, carbon, oxygen, and sulfur containing amorphous and non-homogenous deposits, as indicated by SEM-EDS analysis.

Water Electrolysis toward Elevated Temperature: Advances, Challenges and Frontiers

Since severe global warming and related climate issues have been caused by the extensive utilization of fossil fuels, the vigorous development of renewable resources is needed, and transformation into stable chemical energy is required to overcome the detriment of their fluctuations as energy sources. As an environmentally friendly and efficient energy carrier, hydrogen can be employed in various industries and produced directly by renewable energy (called green hydrogen). Nevertheless, large-scale green hydrogen production by water electrolysis is prohibited by its uncompetitive cost caused by a high specific energy demand and electricity expenses, which can be overcome by enhancing the corresponding thermodynamics and kinetics at elevated working temperatures. In the present review, the effects of temperature variation are primarily introduced from the perspective of electrolysis cells. Following an increasing order of working temperature, multidimensional evaluations considering materials and structures, performance, degradation mechanisms and mitigation strategies as well as electrolysis in stacks and systems are presented based on elevated temperature alkaline electrolysis cells and polymer electrolyte membrane electrolysis cells (ET-AECs and ET-PEMECs), elevated temperature ionic conductors (ET-ICs), protonic ceramic electrolysis cells (PCECs) and solid oxide electrolysis cells (SOECs).

Potential Application of Ionic Liquids for Electrodeposition of the Material Targets for Production of Diagnostic Radioisotopes

An overview of the reported electrochemistry studies on the chemistry of the element for targets for isotope production in ionic liquids (ILs) is provided. The majority of investigations have been dedicated to two aspects of the reactive element chemistry. The first part of this review presents description of the cyclotron targets properties, especially physicochemical characterization of irradiated elements. The second part is devoted to description of the electrodeposition procedures leading to obtain elements or their alloys coatings (e.g., nickel, uranium) as the targets for cyclotron and reactor generation of the radioisotopes. This review provides an evaluation of the role ILs can have in the production of isotopes.

Large-Area Electrodeposition of Few-Layer MoS2 on Graphene for 2D Material Heterostructures

Heterostructures involving two-dimensional (2D) transition metal dichalcogenides and other materials such as graphene have a strong potential to be the fundamental building block of many electronic and optoelectronic applications. The integration and scalable fabrication of such heterostructures are of the essence in unleashing the potential of these materials in new technologies. For the first time, we demonstrate the growth of few-layer MoS₂ films on graphene via nonaqueous electrodeposition. Through methods such as scanning and transmission electron microscopy, atomic force microscopy, Raman spectroscopy, energy- and wavelength-dispersive X-ray spectroscopies, and X-ray photoelectron spectroscopy, we show that this deposition method can produce large-area MoS₂ films with high quality and uniformity over graphene. We reveal the potential of these heterostructures by measuring the photoinduced current through the film. These results pave the way toward developing the electrodeposition method for the large-scale growth of heterostructures consisting of varying 2D materials for many applications.

Near infrared-light responsive WS2 microengines with high-performance electro- and photo-catalytic activities

Tungsten disulfide (WS2)-based micromotors with enhanced electrochemical and photo-catalytic activities are synthesized using a greatly simplified electrochemical deposition protocol at room temperature involving exclusively tungstic acid and sulfate as metal and sulfur sources without further building chemistry. The WS2-based micromotors exhibit dual electrochemical and photo-catalytic behavior in the inner and outer layers, respectively, due to the combination of the unique properties of the sp2 hybridized WS2 outer layer with highly reactive WS2-induced inner catalytic layers, accounting for this material's exclusive enhanced performances. A rough inner Pt-Ni layer allows tailoring the micromotor propulsion, with a speed increase of up to 1.6 times after external control of the micromotor with a magnetic field due to enhanced fuel accessibility. Such a coupling of the attractive capabilities of WS2 with enhanced micromotor movement holds considerable promise to address the growing energy crisis and environmental pollution concerns.

Two-Dimensional Materials in Biosensing and Healthcare: From In Vitro Diagnostics to Optogenetics and Beyond

Since the isolation of graphene in 2004, there has been an exponentially growing number of reports on layered two-dimensional (2D) materials for applications ranging from protective coatings to biochemical sensing. Due to the exceptional, and often tunable, electrical, optical, electrochemical, and physical properties of these materials, they can serve as the active sensing element or a supporting substrate for diverse healthcare applications. In this review, we provide a survey of the recent reports on the applications of 2D materials in biosensing and other emerging healthcare areas, ranging from wearable technologies to optogenetics to neural interfacing. Specifically, this review provides (i) a holistic evaluation of relevant material properties across a wide range of 2D systems, (ii) a comparison of 2D material-based biosensors to the state-of-the-art, (iii) relevant material synthesis approaches specifically reported for healthcare applications, and (iv) the technological considerations to facilitate mass production and commercialization.

Electrodeposition of amorphous molybdenum sulfide thin film for electrochemical hydrogen evolution reaction

Amorphous molybdenum sulfide (MoS_x) is a highly active noble-metal-free electrocatalysts for the hydrogen evolution reaction (HER). The MoS_x was prepared by electrochemical deposition at room temperature. Low-cost precursors of Mo and S were adopted to synthesize thiomolybdates solution as the electrolyte. It replaces the expensive (NH)₂MoS₄ and avoid the poison gas (H₂S) to generate or employ. The (MoO₂S₂)²⁻, (MoOS₃)²⁻ and (MoS₄)²⁻ ions were determined by UV–VIS spectroscopy. The electrodeposition of MoS_x was confirmed with XRD, XPS and SEM. The electrocatalyst activity was measured by polarization curve. The electrolyte contained (MoO₂S₂)²⁻ ion and (MoOS₃)²⁻ ion electrodeposit the MoS_x thin film displays a relatively high activity for HER with low overpotential of 211 mV at a current density of 10 mA cm⁻², a relatively high current density of 21.03 mA cm⁻² at η = 250 mV, a small Tafel slope of 55 mV dec⁻¹. The added sodium dodecyl sulfate (SDS) can efficient improve the stability of the MoS_x film catalyst.

Recent advances in metal sulfides: from controlled fabrication to electrocatalytic, photocatalytic and photoelectrochemical water splitting and beyond

This review describes an in-depth overview and knowledge on the variety of synthetic strategies for forming metal sulfides and their potential use to achieve effective hydrogen generation and beyond.

Electrodeposition of Amorphous Molybdenum Chalcogenides from Ionic Liquids and Their Activity for the Hydrogen Evolution Reaction

This work reports on the general electrodeposition mechanism of tetrachalcogenmetallates from 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide. Both tetrathio- and tetraselenomolybdate underwent anodic electrodeposition and cathodic corrosion reactions as determined by UV-vis spectroelectrochemistry. Electrodeposition was carried out by cycling the potential between the anodic and cathodic regimes. This resulted in a film of densely packed nanoparticles of amorphous MoS_x or MoSe_x as determined by SEM, Raman, and XPS. The films were shown to have high activity for the hydrogen evolution reaction. The onset potential (J = 1 mA/cm²) of the MoS_x film was E = -0.208 V vs RHE, and that of MoSe_x was E = -0.230 V vs RHE. The Tafel slope of MoS_x was 42 mV/decade, and that of MoSe_x was 59 mV/decade.

Valence and oxide impurities in MoS2 and WS2 dramatically change their electrocatalytic activity towards proton reduction

Layered molybdenum disulfide (MoS₂) and tungsten disulfide (WS₂) have received renewed interest in recent years as they are catalytic towards the hydrogen evolution reaction (HER) and they are touted as future replacements of platinum in electrolyzers. There is a significant discrepancy in the found onset potentials of MoS₂ and WS₂ towards the hydrogen evolution reaction. Here we show that the presence of valence sulfide impurities, such as MoS₃ and WS₃, and their oxide counterparts, such as MoO₂, MoO₃ and WO₂, WO₃ can contribute to the catalytic activity towards hydronium reduction to hydrogen of MoS₂ and WS₂. Therefore, it is highly possible that the differences in the reported onset potentials and thus catalytic activities of the MoS₂ and WS₂ are due to the presence of catalytic impurities.

Electrochemical Surface Interrogation of a MoS2 Hydrogen-Evolving Catalyst: In Situ Determination of the Surface Hydride Coverage and the Hydrogen Evolution Kinetics

The hydrogen evolution reaction (HER) on an electrodeposited a-MoS2 electrode was investigated by a surface-selective electrochemical titration technique by application of surface interrogation scanning electrochemical microscopy. In a mildly acidic (pH 4.6) environment, the saturated surface hydride coverage of MoS2 was determined to be 31%, much higher than that expected for a crystalline nanoparticle. The HER rate constant of a surface molybdenum atom was measured for the first time in situ to be 3.8 s(-1) at a 600 mV overpotential. At high Mo-H coverages, a change in the nature of the active sites was observed upon consumption of Mo-H by HER.

Subnanometer Molybdenum Sulfide on Carbon Nanotubes as a Highly Active and Stable Electrocatalyst for Hydrogen Evolution Reaction

Electrochemically splitting water for hydrogen evolution reaction (HER) has been viewed as a promising approach to produce renewable and clean hydrogen energy. However, searching for cheap and efficient HER electrocatalysts to replace the currently used Pt-based catalysts remains an urgent task. Herein, we develop a one-step carbon nanotube (CNT) assisted synthesis strategy with CNTs' strong adsorbability to mediate the growth of subnanometer-sized MoS(x) on CNTs. The subnanometer MoS(x)-CNT hybrids achieve a low overpotential of 106 mV at 10 mA cm(-2), a small Tafel slope of 37 mV per decade, and an unprecedentedly high turnover frequency value of 18.84 s(-1) at η = 200 mV among all reported non-Pt catalysts in acidic conditions. The superior performance of the hybrid catalysts benefits from the presence of a higher number of active sites and the abundant exposure of unsaturated S atoms rooted in the subnanometer structure, demonstrating a new class of subnanometer-scale catalysts.

Controllable synthesis of three dimensional electrodeposited Co–P nanosphere arrays as efficient electrocatalysts for overall water splitting

Novel three dimensional (3D) electrodeposited Co–P nanosphere arrays on FTO (Co–P/FTO) have been successfully prepared as efficient bifunctional electrocatalysts for overall water splitting in alkaline media.

TiO2-based photoanodes modified with GO and MoS2 layered materials

MoS₂/TiO₂ and GO/TiO₂ nanocomposites synthesized via electrodeposition (GO, MoS₂) with enhanced photocurrent response.

Evidence of a nanosized copper anodic reaction in an anaerobic sulfide aqueous solution

The present paper reports the use of TEM to investigate the electrochemical behavior of copper subject to the both free corrosion and polarization in sulfide aqueous solution at nano scale.

Extraordinary magneto-optical Kerr effect via MoS2 monolayer in Au/Py/MoS2 plasmonic cavity

We demonstrate a multilayer magnetoplasmonic structure fabricated from MoS₂ monolayer to significantly increase the transverse magneto-optical Kerr effect (TMOKE) with a signal Q-factor more than 600.

The synthesis and electrical properties of hybrid gel electrolytes derived from Keggin-type heteropoly acids and 3-(pyridin-1-ium-1-yl)propane-1-sulfonate (PyPs)

Cyclic voltammetry of PyPs–H₃PWMo at room temperature between −4 and +4 V vs. Ag/AgCl at a 10 mV s⁻¹ scan rate and comparison of electrical conductivity of PyPs–H₃PWMo with other known promising proton conductors.

Structure and Dynamics of Ionic Liquids Confined in Amorphous Porous Chalcogenides

Besides the abundant literature on ionic liquids in porous silica and carbon, the confinement of such intriguing liquids in porous chalcogenides has received very little attention. Here, molecular simulation is employed to study the structural and dynamical properties of a typical ionic liquid confined in a realistic molecular model of amorphous chalcogenide with various pore sizes and surface chemistries. Using molecular dynamics in the isobaric-isothermal (NPT) ensemble, we consider confinement conditions relevant to real samples. Both the structure and self-dynamics of the confined phase are found to depend on the surface-to-volume ratio of the host confining material. Consequently, most properties of the confined ionic liquid can be written as a linear combination of surface and bulk-like contributions, arising from the ions in contact with the surface and the ions in the pore center, respectively. On the other hand, collective dynamical properties such as the ionic conductivity remain close to their bulk counterpart and almost insensitive to pore size and surface chemistry. These results, which are in fair agreement with available experimental data, provide a basis for the development of novel applications using hybrid organic-inorganic solids consisting of ionic liquids confined in porous chalcogenides.

Plasmonic hot electron enhanced MoS2 photocatalysis in hydrogen evolution

With plasmonic hot electron doping, the molybdenum disulfide (MoS2) monolayer with deposited Au@Ag nanorattles effectively enhanced the hydrogen evolution reaction (HER) efficiency. The maximum photocatalysis is achieved under plasmon resonance excitation, and is actively controlled by the incident laser wavelength and power intensity. The localized phase transition of MoS2 is achieved and characterized to explicate this plasmon-enhanced hydrogen evolution. The proposed MoS2-nanoparticle composite combines surface plasmons and planar 2D materials, and pioneers a frontier field of plasmonic MoS2 photocatalysis.

Well-constructed single-layer molybdenum disulfide nanorose cross-linked by three dimensional-reduced graphene oxide network for superior water splitting and lithium storage property

A facile one-step solution reaction route for growth of novel MoS2 nanorose cross-linked by 3D rGO network, in which the MoS2 nanorose is constructed by single-layered or few-layered MoS2 nanosheets, is presented. Due to the 3D assembled hierarchical architecture of the ultrathin MoS2 nanosheets and the interconnection of 3D rGO network, as well as the synergetic effects of MoS2 and rGO, the as-prepared MoS2-NR/rGO nanohybrids delivered high specific capacity, excellent cycling and good rate performance when evaluated as an anode material for lithium-ion batteries. Moreover, the nanohybrids also show excellent hydrogen-evolution catalytic activity and durability in an acidic medium, which is superior to MoS2 nanorose and their nanoparticles counterparts.

Noble metal-free hydrogen evolution catalysts for water splitting

This review summarizes the recent research efforts toward noble metal-free hydrogen evolution electrocatalysts.

Water in ionic liquids at electrified interfaces: the anatomy of electrosorption

Complete removal of water from room-temperature ionic liquids is nearly impossible. For the electrochemical applications of ionic liquids, how water is distributed in the electrical double layers when the bulk liquids are not perfectly dry can potentially determine whether key advantages of ionic liquids, such as a wide electrochemical window, can be harnessed in practical systems. In this paper, we study the adsorption of water on electrode surfaces in contact with humid, imidazolium-based ionic liquids using molecular dynamics simulations. The results revealed that water molecules tend to accumulate within sub-nanometer distance from charged electrodes. At low amount of water in the bulk, the distributions of ions and of electrostatic potential in the double layer are affected weakly by the presence of water, but the spatial distribution of water molecules is strongly dependent on both. The preferential positions of water molecules in double layers are determined by the balance of several factors: the tendency to follow the positions of the maximal absolute value of the electrical field, the association with their ionic surroundings, and the propensity to settle at positions where more free space is available. The balance between these factors changes with charging the electrode, but the adsorption of water generally increases with voltage. The ion specificity of water electrosorption is manifested in the stronger presence of water near positive electrodes (where anions are the counterions) than near negative electrodes (where cations are counterions). These predictions await experimental verification.

Electrochemically Created Highly Surface Roughened Ag Nanoplate Arrays for SERS Biosensing Applications

Highly surface-roughened Ag nanoplate arrays are fabricated using a simple electrodeposition and in situ electrocorrosion method with inorganic borate ions as capping agent. The electrocorrosion process is induced by a change in the local pH value during the electrochemical growth, which is used to intentionally carve the electrodeposited structures. The three dimensionally arranged Ag nanoplates are integrated with substantial surface-enhanced Raman scattering (SERS) hot spots and are free of organic contaminations widely used as shaping agents in previous works, making them excellent candidate substrates for SERS biosensing applications. The SERS enhancement factor of the rough Ag nanoplates is estimated to be > 109. These Ag nanoplate arrays are used for SERS-based analysis of DNA hybridization monitoring, protein detection, and virus differentiation without any additional surface modifications or labelling. They all exhibit an extremely high detection sensitivity, reliability, and reproducibility.

Plasmonic hot electron induced structural phase transition in a MoS2 monolayer

A reversible 2H-to-1T phase transition in a MoS2 monolayer is realized by plasmonic hot electrons. This transition can be actively controlled by the incident light intensity, wavelength, sample areas, and perimeters, resulting in an effective shift of photoluminescence. The suggested configuration paves the way for plasmonic optoelectronic device applications of MoS2 in the future.

Superior electrochemical properties of MoS2 powders with a MoS2@void@MoS2 configuration

Yolk-shell MoS2 powders with a distinct configuration of MoS2@void@MoS2 were prepared for the first time by applying spray pyrolysis. The yolk-shell MoO3 powders prepared by spray pyrolysis were converted into MoS2 powders by a simple sulfidation process at 400 °C without altering the morphology. Dense structured MoS2 powders were also prepared by a similar process. The respective initial discharge capacities of the yolk-shell and dense structured MoS2 powders at a current density of 1000 mA g(-1) were 651 and 490 mA h g(-1), and the corresponding capacity retentions after 100 cycles measured from the second cycle were 100 and 72%.