Visualization of texture components using MTEX

Knowledge of the appearance of texture components and fibres in pole figures, in inverse pole figures and in Euler space is fundamental for texture analysis. For cubic crystal systems, such as steels, an extensive literature exists and, for example, the book by Matthies, Vinel & Helming [Standard Distributions in Texture Analysis: Maps for the Case of Cubic Orthorhomic Symmetry, (1987), Akademie-Verlag Berlin] provides an atlas to identify texture components. For lower crystal symmetries, however, equivalent comprehensive overviews that can serve as guidance for the interpretation of experimental textures do not exist. This paper closes this gap by providing a set of scripts for the MTEX package [Bachmann, Hielscher & Schaeben (2010). Solid State Phenom. 160, 63-68] that allow the texture practitioner to compile such an atlas for a given material system, thus aiding orientation distribution function analysis also for non-cubic systems.

Strain-Induced Graphitization Mechanism of Coal-Based Graphite from Lutang, Hunan Province, China

Anthracite and coal-based graphite (CBG) samples were collected at varying distances from a granite intrusion. Optical microscopy, X-ray diffraction, Raman spectroscopy, and high-resolution transmission electron microscopy (HRTEM) were used to characterize the structural evolution of CBG at different scales. The results indicated differences in the graphitization rates of coal macerals and crystallization degree of different graphite-like particles. Differentiated graphitization of coal was caused by deformation, which led to the discontinuous distribution of CBG. This indicates that samples located at the same distance from the intrusion were graphitized to different degrees or that CBG with a similar graphitization degree occurred at varying distances from the intrusion. A possible mechanism for graphitization is strain-induced graphitization, where the local stress concentration leads to preferred orientations of the basic structure units (BSUs), as well as the motion and rearrangement of structural defects, resulting in the formation of a locally ordered structure. The graphitization degree is enhanced as the local graphite structure spreads.

Preferred Orientation of Quartz in Metamorphic Rocks from the Bergell Alps

Crystal preferred orientation of 47 samples of quartzite and eight samples of associated marbles from the Bergell Alps have been analyzed with time-of-flight neutron diffraction and EBSD. The results show a clear distinction of texture types for quartzites transformed from Triassic sandstones and quartz layers in gneiss. Textures of Triassic quartzites are overall weak and display a maximum of c-axes perpendicular to the foliation or a crossed girdle perpendicular to the lineation. Pole figures for positive rhombs {10 1 ¯ 1} show a maximum perpendicular to the foliation and negative rhombs {01 1 ¯ 1} generally display a minimum. Based on polycrystal plasticity models this texture type can be attributed to a combination of basal and rhombohedral slip. Asymmetry of the distributions is attributed to simple shear and local strain heterogeneities. The relatively weak texture is partially caused by muscovite limiting dislocation motion and grain growth, as well as adjacent layers of marble that accommodate significant strain. Most quartz layers in gneiss, including mylonites, display a texture with a-axes parallel to the lineation and a c-axis maximum in the intermediate fabric direction. This texture type can be attributed to dominant prismatic slip. Many samples are recrystallized and recrystallization appears to strengthen the deformation texture. The study shows good agreement of neutron diffraction and EBSD. Neutron diffraction data average over larger volumes and maximum pole densities are generally lower and more representative for the bulk material. With EBSD the microstructure and mechanical twinning can be quantified.

Microstructural Evidence for Grain Boundary Migration and Dynamic Recrystallization in Experimentally Deformed Forsterite Aggregates

Plastic deformation of peridotites in the mantle involves large strains. Orthorhombic olivine does not have enough slip systems to satisfy the von Mises criterion, leading to strong hardening when polycrystals are deformed at rather low temperatures (i.e., below 1200 °C). In this study, we focused on the recovery mechanisms involving grain boundaries and recrystallization. We investigated forsterite samples deformed at large strains at 1100 °C. The deformed microstructures were characterized by transmission electron microscopy using orientation mapping techniques (ACOM-TEM). With this technique, we increased the spatial resolution of characterization compared to standard electron backscatter diffraction (EBSD) maps to further decipher the microstructures at nanoscale. After a plastic strain of 25%, we found pervasive evidence for serrated grain and subgrain boundaries. We interpreted these microstructural features as evidence of occurrences of grain boundary migration mechanisms. Evaluating the driving forces for grain/subgrain boundary motion, we found that the surface tension driving forces were often greater than the strain energy driving force. At larger strains (40%), we found pervasive evidence for discontinuous dynamic recrystallization (dDRX), with nucleation of new grains at grain boundaries. The observations reveal that subgrain migration and grain boundary bulging contribute to the nucleation of new grains. These mechanisms are probably critical to allow peridotitic rocks to achieve large strains under a steady-state regime in the lithospheric mantle.

Texturing of the Earth's inner core by Maxwell stresses

Elastic anisotropy in the Earth's inner core has been attributed to a preferred lattice orientation, which may be acquired during solidification of the inner core or developed subsequent to solidification as a result of plastic deformation. But solidification texturing alone cannot explain the observed depth dependence of anisotropy, and previous suggestions for possible deformation processes have all relied on radial flow, which is inhibited by thermal and chemical stratification. Here we investigate the development of anisotropy as the inner core deforms plastically under the influence of electromagnetic (Maxwell) shear stresses. We estimate the flow caused by a representative magnetic field using polycrystal plasticity simulations for epsilon-iron, where the imposed deformation is accommodated by basal and prismatic slip. We find that individual grains in an initially random polycrystal become preferentially oriented with their c axes parallel to the equatorial plane. This pattern is accentuated if deformation is accompanied by recrystallization. Using the single-crystal elastic properties of epsilon-iron at core pressure and temperature, we average over the simulated orientation distribution to obtain a pattern of elastic anisotropy which is similar to that observed seismologically.

High shear strain of olivine aggregates: rheological and seismic consequences

High-pressure and high-temperature torsion experiments on olivine aggregates in dislocation creep show about 15 to 20% strain weakening before steady-state behavior, characterized by subgrain-rotation recrystallization and a strong lattice preferred orientation. Such weakening may provide a way to focus flow in the upper mantle without a change in deformation mechanism. Flow laws derived from low strain data may not be appropriate for use in modeling high strain regions. In such areas, seismic wave propagation will be anisotropic with an axis of approximate rotational symmetry about the shear direction. In contrast to current thinking, the anisotropy will not indicate the orientation of the shear plane in highly strained, recrystallized olivine-rich rocks.