Microstructural Evolution of Amphibole Peridotites in Åheim, Norway, and the Implications for Seismic Anisotropy in the Mantle Wedge

The microstructure of amphibole peridotites from Åheim, Norway were analyzed to understand the evolution of the lattice-preferred orientation (LPO) of olivine throughout the Scandian Orogeny and its implication for the seismic anisotropy of the subduction zone. The Åheim peridotites had a porphyroclastic texture and some samples contained an abundant amount of hydrous minerals such as tremolite. Detailed microstructural analysis on the Åheim peridotites revealed multiple stages of deformation. The coarse grains showed an A-type LPO of olivine, which can be interpreted as the initial stage of deformation. The spinel-bearing samples showed a mixture of B-type and C-type LPOs of olivine, which is considered to represent the deformation under water-rich conditions. The recrystallized fine-grained olivine displays a B-type LPO, which can be interpreted as the final stage of deformation. Microstructures and water content of olivine indicate that the dominant deformation mechanism of olivine showing a B-type LPO is a dislocation creep under water-rich condition. The observation of the B-type LPO of olivine is important for an interpretation of trench-parallel seismic anisotropy in the mantle wedge. The calculated seismic anisotropy of the tremolite showed that tremolite can contribute to the trench-parallel seismic anisotropy in the mantle wedge.

Water pumping in mantle shear zones

Water plays an important role in geological processes. Providing constraints on what may influence the distribution of aqueous fluids is thus crucial to understanding how water impacts Earth's geodynamics. Here we demonstrate that ductile flow exerts a dynamic control on water-rich fluid circulation in mantle shear zones. Based on amphibole distribution and using dislocation slip-systems as a proxy for syn-tectonic water content in olivine, we highlight fluid accumulation around fine-grained layers dominated by grain-size-sensitive creep. This fluid aggregation correlates with dislocation creep-accommodated strain that localizes in water-rich layers. We also give evidence of cracking induced by fluid pressure where the highest amount of water is expected. These results emphasize long-term fluid pumping attributed to creep cavitation and associated phase nucleation during grain size reduction. Considering the ubiquitous process of grain size reduction during strain localization, our findings shed light on multiple fluid reservoirs in the crust and mantle.

Seismic anisotropy evidence for dehydration embrittlement triggering intermediate-depth earthquakes

It has been proposed that dehydration embrittlement of hydrous materials can trigger intermediate-depth earthquakes and form a double seismic zone in a subducting slab. Seismic anisotropy may provide a possible insight into intermediate-depth intraslab seismicity, because anisotropic properties of minerals change with varying water distribution, temperature and pressure. Here we present a high-resolution model of P-wave radial anisotropy tomography of the Japan subduction zone down to ~400 km depth, which is obtained using a large number of arrival-time data of local earthquakes and teleseismic events. Our results reveal a close correlation between the pattern of intermediate-depth seismicity and anisotropic structures. The seismicity occurs in portions of the Pacific and Philippine Sea slabs where positive radial anisotropy (i.e., horizontal velocity being faster than vertical one) dominates due to dehydration, whereas the inferred anhydrous parts of the slabs are found to be aseismic where negative radial anisotropy (i.e., vertical velocity being faster than horizontal one) dominates. Our anisotropic results suggest that intermediate-depth earthquakes in Japan could be triggered by dehydration embrittlement of hydrous minerals in the subducting slabs.

Dislocation-accommodated grain boundary sliding as the major deformation mechanism of olivine in the Earth's upper mantle

Understanding the deformation mechanisms of olivine is important for addressing the dynamic processes in Earth's upper mantle. It has been thought that dislocation creep is the dominant mechanism because of extrapolated laboratory data on the plasticity of olivine at pressures below 0.5 GPa. However, we found that dislocation-accommodated grain boundary sliding (DisGBS), rather than dislocation creep, dominates the deformation of olivine under middle and deep upper mantle conditions. We used a deformation-DIA apparatus combined with synchrotron in situ x-ray observations to study the plasticity of olivine aggregates at pressures up to 6.7 GPa (that is, ~200-km depth) and at temperatures between 1273 and 1473 K, which is equivalent to the conditions in the middle region of the upper mantle. The creep strength of olivine deforming by DisGBS is apparently less sensitive to pressure because of the competing pressure-hardening effect of the activation volume and pressure-softening effect of water fugacity. The estimated viscosity of olivine controlled by DisGBS is independent of depth and ranges from 10(19.6) to 10(20.7) Pa·s throughout the asthenospheric upper mantle with a representative water content (50 to 1000 parts per million H/Si), which is consistent with geophysical viscosity profiles. Because DisGBS is a grain size-sensitive creep mechanism, the evolution of the grain size of olivine is an important process controlling the dynamics of the upper mantle.

Trench-Parallel Anisotropy Produced by Foundering of Arc Lower Crust

Many volcanic arcs display fast seismic shear-wave velocities parallel to the strike of the trench. This pattern of anisotropy is inconsistent with simple models of corner flow in the mantle wedge. Although several models, including slab rollback, oblique subduction, and deformation of water-rich olivine, have been proposed to explain trench-parallel anisotropy, none of these mechanisms are consistent with all observations. Instead, small-scale convection driven by the foundering of dense arc lower crust provides an explanation for the trench-parallel anisotropy, even in settings with orthogonal convergence and no slab rollback.