Effect of Polyoxymethylene (POM-H Delrin) offgassing within Pandora head sensor on direct sun and multi-axis formaldehyde column measurements in 2016 - 2019

Analysis of formaldehyde measurements by the Pandora spectrometer systems between 2016 and 2019 suggested that there was a temperature dependent process inside Pandora head sensor that emitted formaldehyde. Some parts in the head sensor were manufactured from thermal plastic polyoxymethylene homopolimer (E.I. Du Pont de Nemour & Co., USA: POM-H Delrin®) and were responsible for formaldehyde production. Laboratory analysis of the four Pandora head sensors showed that internal formaldehyde production had exponential temperature dependence with a damping coefficient of 0.0911±0.0024 °C^-1 and the exponential function amplitude ranging from 0.0041 DU to 0.049 DU. No apparent dependency on the head sensor age and heating/cooling rates was detected. The total amount of formaldehyde internally generated by the POM-H Delrin components and contributing to the direct sun measurements were estimated based on the head sensor temperature and solar zenith angle of the measurements. Measurements in winter, during colder (<10°C) days in general and at high solar zenith angles (> 75 °) were minimally impacted. Measurements during hot days (>28°C) and small solar zenith angles had up to 1 DU (2.69×10¹⁶ molecules/cm²) contribution from POM-H Delrin parts. Multi-axis differential slant column densities were minimally impacted (< 0.01 DU) due to the reference spectrum collected within a short time period with a small difference in head sensor temperature. Three new POM-H Delrin free Pandora head sensors (manufactured in summer 2019) were evaluated for temperature dependent attenuation across the entire spectral range (300 to 530 nm). No formaldehyde or any other absorption above the instrumental noise was observed across the entire spectral range.

Improved spherical mirror multipass-cell-based interband cascade laser spectrometer for detecting ambient formaldehyde at parts per trillion by volume levels

We report the development of an improved spherical mirror multipass-cell-based interband cascade laser (ICL) spectrometer for ambient formaldehyde (HCHO) detection. The multipass cell consists of two easily manufactured spherical mirrors that are low cost, and have a simple structure, large mirror area utilization, and dense spot pattern. Optical interference caused by the multipath cell was largely reduced, resulting in good sensitivity. Using wavelength modulation spectroscopy (WMS), a detection precision (${1} \sigma $1σ) of 51 pptv in 10 s was achieved with an absorption pathlength of 96 m, which compared favorably with the performance of other state-of-the-art instruments. The precision can be further improved by using a long absorption pathlength configuration and by removing fringe-like optical noise caused by the collimation lens. Ambient application of the developed spectrometer was demonstrated.

Formaldehyde content of atmospheric aerosol

Formaldehyde (HCHO) is a highly soluble polar molecule with a large sticking coefficient and thus likely exists in both gaseous and particulate forms. Few studies, however, address particulate HCHO (HCHO(p)). Some report that HCHO(p) concentrations (obtained only with long duration sampling) are very low. The lack of data partly reflects the difficulty of specifically measuring HCHO(p). Long duration filter sampling may not produce meaningful results for a variety of reasons. In this work, gaseous HCHO (HCHO(g)) and (HCHO(p)) were, respectively, collected with a parallel plate wet denuder (PPWD) followed by a mist chamber/hydrophilic filter particle collector (PC). The PPWD quantitatively removed HCHO(g) and the PC then collected the transmitted aerosol. The collected HCHO from either device was alternately analyzed by Hantzsch reaction-based continuous flow fluorometry. Each gas and particle phase measurement took 5 min each, with a 10 min cycle. The limits of detection were 0.048 and 0.0033 μg m(-3), respectively, for HCHO(g) and HCHO(p). The instrument was deployed in three separate campaigns in a forest station in western Japan in March, May, and July of 2013. Based on 1296 data pairs, HCHO(p), was on the average, 5% of the total HCHO. Strong diurnal patterns were observed, with the HCHO(p) fraction peaking in the morning. The relative humidity dependence of the partition strongly suggests that it is driven by the liquid water content of the aerosol phase. However, HCHO(p) was 100× greater than that expected from Henry's law. We propose that the low water activity in the highly saline droplets lead to HCHO oligomerization.

A new device for formaldehyde and total aldehydes real-time monitoring

A new sensitive technique for the quantification of formaldehyde (HCHO) and total aldehydes has been developed in order to monitor these compounds, which are known to be involved in air quality issues and to have health impacts. Our approach is based on a colorimetric method where aldehydes are initially stripped from the air into a scrubbing solution by means of a turning coil sampler tube and then derivatised with 3-methylbenzothiazolinone-2-hydrazone in acid media (pH = -0.5). Hence, colourless aldehydes are transformed into blue dyes that are detected by UV-visible spectroscopy at 630 nm. Liquid core waveguide LCW Teflon® AF-2400 tube was used as innovative optical cells providing a HCHO detection limit of 4 pptv for 100 cm optical path with a time resolution of 15 min. This instrument showed good correlation with commonly used techniques for aldehydes analysis such as DNPH derivatisation chromatographic techniques with off-line and on-line samplers, and DOAS techniques (with deviation below 6%) for both indoor and outdoor conditions. This instrument is associated with simplicity and low cost, which is a prerequisite for indoor monitoring.

Robust hybrid flow analyzer for formaldehyde

We report fully automated self-calibrating formaldehyde analyzers relying on a hybrid flow format and include operational scheme and design details. Long-term operation is made possible with the use of syringe pumps. Four identical analyzers were built and showed low LODs of 120 pptv or better (S/N = 3) and good linearity over 0-50 ppbv HCHO concentration range (r2 > 0.9960), all concentrations refer to 10 min averaging times. The analyzer can resume normal operation after shortterm power failure with at most two cycles of data loss following restart. Good agreement between analyzers was observed for either indoor or outdoor measurements. The use of an integrated HCHO calibration source and full control by the host computer via a graphical user interface program enables the instrument to switch between zero, calibration, and sampling modes in a programmed automated manner. Detailed field data from deployment in three urban Texas locations from the summer of 2006 are presented. Features of the data, including an episode in which the HCHO concentration exceeded 50 ppbv, the highest reported ambient HCHO concentration in North America to our knowledge, are discussed in some detail.

Isotopic Analysis of Atmospheric Formaldehyde by Gas Chromatography Isotope Ratio Mass Spectrometry

Little is known about the isotopic composition of formaldehyde in the atmosphere, a chemical intermediate in hydrocarbon oxidation. Here, we present a promising new method to analyze the carbon (delta 13C) and hydrogen (delta D) isotopic composition of atmospheric formaldehyde. The direct isotopic analytical technique described uses continuous-flow gas chromatography-isotope ratio mass spectrometry, which provides flexibility for either isotopic analysis without correction for derivative functional groups. Current levels of precision of measurement are +/-1.1 and +/-50 per thousand (1 sigma) for delta 13C and delta D analyses, respectively. Concentration of formaldehyde in ambient air is also determined, coincident with isotopic measurement, to a precision of +/-15%. The method has the required sensitivity for analyses of formaldehyde in urban air on relatively small volume grab samples of whole air (10-70L STP), potentially providing high temporal resolution. This is particularly advantageous for studying formaldehyde given its short lifetime and large variability in the atmosphere.

Summertime ambient formaldehyde in five U.S. metropolitan areas: Nashville, Atlanta, Houston, Philadelphia, and Tampa

First, we briefly review the atmospheric chemistry and previous intercomparison measurements for HCHO, with special reference to the diffusion scrubber Hantzsch reaction based fluorescence instrument used in the field studies reported herein. Then we discuss summertime HCHO levels in five major U.S. cities measured over 1999-2002, primarily from ground-based measurements. Land-sea breeze circulations play a major role in observed concentrations in coastal cities. Very high HCHO peak mixing ratios were observed in Houston (>47 ppb) where the overall median mixing ratio was 3.3 ppb; the corresponding values in Atlanta were approximately >18 and 7.9 ppb, respectively. The peak and median mixing ratios (9.3 and 2.3 ppb) were the lowest for Tampa, where the land-sea breeze also played an important role. In several cities, replicate HCHO measurements were made by direct spectroscopic instruments; the instruments were located kilometers from each other and addressed very different heights (e.g., 106 vs 10 m). Even under these conditions, there was remarkable qualitative and often quantitative agreement between the different instruments, when they were all sampling the same air mass within a short period of each other. Local chemistry dominates how HCHO is formed and dissipated. The high concentrations in Houston resulted from emissions near the ship channel; the same formaldehyde plume was measured at two sites and clearly ranged over tens of kilometers. Local micrometeorology is another factor. HCHO patterns measured at a high-rise site in downtown Nashville were very much in synchrony with other ground sites 12 km away until July 4 celebrations whence HCHO concentrations at the downtown site remained elevated for several days and nights. The formation and dissipation of HCHO in the different cities are discussed in terms of other concurrently measured species and meteorological vectors. The vertical profiles of HCHO in and around Tampa under several different atmospheric conditions are presented. The extensive data set represented in this paper underscores that urban HCHO measurements can now be made easily; the agreement between disparate instruments (that are independently calibrated or rely on the absolute absorption cross section) further indicates that such measurements can be done reliably and accurately for this very important atmospheric species. The data set presented here can be used as a benchmark for future measurements if the use of formaldehyde precursors such as methanol or methyl tert-butyl ether (MTBE) as oxygenated fuel additives increases in the future.

Atmospheric formaldehyde monitoring in the Greater Houston area in 2002

A laser spectrometer based on difference frequency generation (DFG) was deployed for real-time long-term monitoring of HCHO concentrations at an environmental monitoring site located at Deer Park, Texas, in the Greater Houston area. Three HCHO concentration measurements were made during the periods of July 20-31 (period I), August 2-14 (period II), and August 24-September 25 (period III), 2002. In periods I and II, differences in HCHO concentrations are apparent between day and night measurements, with elevated concentrations during daylight hours. Most of the HCHO peak values are less than 20 ppbV except for two intense peaks on August 02 (approximately 25 ppbV) and August 04 (approximately 30 ppbV). The formaldehyde concentration levels in ambient air at the measurement site are produced mainly by the photochemical oxidation of volatile organic compounds (VOCs) caused by intense sunlight during periods I and II. This observation was made based on a comparison with the ozone concentration, solar radiation, temperature, relative humidity, and wind speed data obtained from the Texas Commission on Environmental Quality (TCEQ). During period III, data collected by a time-integrating wet-chemical technique are compared to the data collected by the spectroscopic instrument.

A continuous film-recirculable drop gas-liquid equilibration device. Measurement of trace gaseous ammonia

A miniature gas-liquid equilibrator or a gas collector, intended as a low-volume interface between a soluble gaseous sample and a liquid phase analyzer or between a liquid phase sample and a detector designed for use with gas samples, is described. This paper addresses the application of the device for the measurement of trace atmospheric ammonia. Gas collection occurs solely by diffusive sampling such that aerosol particles are not collected. The device essentially consists of a tube surrounded externally by a jacket. Gas flows through the jacket and contacts a liquid film flowing on the surface of the tube. The flowing film forms a drop at the tube terminus and is aspirated off through the inner bore of the tube. The collected analyte can be (a) directly sent to an analysis system or (b) preconcentrated on a suitable stationary phase; the preconcentrator effluent can be recycled, if desired. With a fluorometric flow injection analysis system harnessed to measure ammonia with such a collector, the limit of detection (LOD, S/N = 3) for a sample drawn for 18 min at 200 mL/min was 4.5 parts per trillion by volume, with the linear range extending up to 30 parts per billion.