Atomically thin micas as proton-conducting membranes

In situ generation of (sub) nanometer pores in MoS2 membranes for ion-selective transport

Ion selective membranes are fundamental components of biological, energy, and computing systems. The fabrication of solid-state ultrathin membranes that can separate ions of similar size and the same charge with both high selectivity and permeance remains a challenge, however. Here, we present a method, utilizing the application of a remote electric field, to fabricate a high-density of (sub)nm pores in situ. This method takes advantage of the grain boundaries in few-layer polycrystalline MoS2 to enable the synthesis of nanoporous membranes with average pore size tunable from <1 to ~4 nm in diameter (with in situ pore expansion resolution of ~0.2 nm2 s-1). These membranes demonstrate selective transport of monovalent ions (K+, Na+ and Li+) as well as divalent ions (Mg2+ and Ca2+), outperforming existing two-dimensional material nanoporous membranes that display similar total permeance. We investigate the mechanism of selectivity using molecular dynamics simulations and unveil that the interactions between cations and the sluggish water confined to the pore, as well as cation-anion interactions, result in the different transport behaviors observed between ions.

Two-dimensional ice-like water adlayers on a mica surface with and without a graphene coating under ambient conditions

Water tends to wet all hydrophilic surfaces under ambient conditions, and the first water adlayers on solids are important for a broad range of physicochemical phenomena and technological processes, including corrosion, wetting, lubrication, anti-icing, catalysis, and electrochemistry. Unfortunately, challenges in characterizing the first water adlayer in the laboratory have hampered molecular-level understanding of the contact water structure. Herein, we present the first ab initio molecular dynamics simulation evidence of a previously unreported ice-like adlayer structure (named as Ice-AL-II) on a prototype mica surface under ambient conditions. Calculation showed that the newly identified Ice-AL-II structure is more stable than the widely recognized ice-adlayer structure on mica surfaces (named as Ice-AL-I). Ice-AL-II exhibited a face-centered corner-cut tetragon (or a face-centered irregular pentagon) pattern of a hydrogen-bonded network. The center of the corner-cut tetragon was occupied by either a K+ cation or a water molecule with two H atoms pinned by the mica (100) via double hydrogen bonds. Our simulation also suggested that bilayer Ice-AL-II favors AA stacking rather than AB stacking. Interestingly, when a graphene sheet was coated on top of the ice-like adlayer, the stability of Ice-AL-II was further enhanced. In contrast, due to its strongly puckered structure, the Ice-AL-I structure could be crushed into a near-Ice-AL-II structure by the graphene coating. Ice-AL-II is thus proposed as a promising candidate for the ice-like structure on a mica surface detected by scanning polarization force microscopy and by atomic force microscopy between a graphene coating and a mica surface.

Covalent Organic Framework Interlayer Spacings as Perfectly Selective Artificial Proton Channels

Biological proton channels have perfect selectivity in aqueous environment against almost all ions and molecules, a property that differs itself from other biological channels and a feature that remains challenging to realize for bulk artificial materials. The biological perfect selectivity originates from the fact that the channel has almost no free space for ion or water transport but generates a hydrogen bonded wire in the presence of protons to allow the proton hopping. Inspired by this, we used the interlayer spacings of covalent organic framework materials consisting of hydrophilic functional groups as perfectly selective artificial proton channels. The interlayer spacings are so narrow that no atoms or molecules can diffuse through. However, protons exhibit a diffusivity in the same order of magnitude as that in bulk water. Density functional theory calculations show that water molecules and the COF material form hydrogen bonded wires, allowing the proton hopping. We further demonstrate that the proton transport rate can be tuned by adjusting the acidity of the functional groups.

Proton and molecular permeation through the basal plane of monolayer graphene oxide

Two-dimensional (2D) materials offer a prospect of membranes that combine negligible gas permeability with high proton conductivity and could outperform the existing proton exchange membranes used in various applications including fuel cells. Graphene oxide (GO), a well-known 2D material, facilitates rapid proton transport along its basal plane but proton conductivity across it remains unknown. It is also often presumed that individual GO monolayers contain a large density of nanoscale pinholes that lead to considerable gas leakage across the GO basal plane. Here we show that relatively large, micrometer-scale areas of monolayer GO are impermeable to gases, including helium, while exhibiting proton conductivity through the basal plane which is nearly two orders of magnitude higher than that of graphene. These findings provide insights into the key properties of GO and demonstrate that chemical functionalization of 2D crystals can be utilized to enhance their proton transparency without compromising gas impermeability.

Extreme Ion-Transport Inorganic 2D Membranes for Nanofluidic Applications

Inorganic 2D materials offer a new approach to controlling mass diffusion at the nanoscale. Controlling ion transport in nanofluidics is key to energy conversion, energy storage, water purification, and numerous other applications wherein persistent challenges for efficient separation must be addressed. The recent development of 2D membranes in the emerging field of energy harvesting, water desalination, and proton/Li-ion production in the context of green energy and environmental technology is herein discussed. The fundamental mechanisms, 2D membrane fabrication, and challenges toward practical applications are highlighted. Finally, the fundamental issues of thermodynamics and kinetics are outlined along with potential membrane designs that must be resolved to bridge the gap between lab-scale experiments and production levels.

Exotic Electronic Properties of 2D Nanosheets Isolated from Liquid Phase Exfoliated Phyllosilicate Minerals

Spectrally inactive, electrically insulating, and chemically inert are adjectives broadly used to describe phyllosilicate minerals like mica and chlorite. Here, the above is disproved by demonstrating aqueous suspensions of liquid exfoliated nanosheets from five bulk mica types and chlorite schist. Nanosheet quality is confirmed via transmission electron and X-ray photoelectron spectroscopies, as well as electron diffraction. Through Raman spectroscopy, a previously unreported size- and layer-dependent spectral fingerprint is observed. When analyzing the high-yield suspensions (≈1 mg mL-1 ) through UV-vis spectroscopy, all phyllosilicates present bandgap (Eg ) narrowing from ≈7 eV in the bulk to ≈4 eV for monolayers. Unusually, the bandgap is inversely proportional to the areal size (A) of the nanosheets, measured via atomic force microscopy. Due to an unrecorded quantum confinement effect, nanosheet electronic properties scale toward semiconducting behavior (bandgap ≈3 eV) as nanosheet area increases. Furthermore, modeling X-ray diffraction spectra shows that the root cause of the initial bandgap narrowing is lattice relaxation. Finally, with their broad range of isomorphically substituted ions, phyllosilicate nanosheets show remarkable catalytic properties for hydrogen production.

Superhigh and Robust Ion Selectivity in Membranes Assembled with Monolayer Clay Nanosheets

It is crucial to control the ion transport in membranes for various technological applications such as energy storage and conversion. The emerging functional two-dimensional (2D) nanosheets such as graphene oxide and MXenes show great potential for constructing ordered nanochannels, but the assembled membranes suffer from low ion selectivity and stability. Here a class of robust charge-selective membranes with superhigh cation/anion selectivity, which are assembled with monolayer nanosheets of cationic/anionic clays that inherently have permanent and uniform charges on each layer is reported. The transport number of cations/anions of cationic vermiculite nanosheet membranes (VNMs)/anionic Co-Al layered double hydroxide (CoAl-LDH) nanosheet membranes is over 0.90 in different NaCl concentration gradients, outperforming all the reported ion-selective membranes. Importantly, this excellent ion selectivity can persist at high-concentration salt solutions, under acidic and alkaline conditions, and for a wide range of ions of different sizes and charges. By coupling a pair of cation-selective vermiculite membrane and anion-selective CoAl-LDH membrane, a reverse electrodialysis device which shows an output power density of 0.7 W m-2 and energy conversion efficiency of 45.5% is constructed. This work provides a new strategy to rationally design high-performance ion-selective membranes by using 2D nanosheets with inherent surface charges for controllable ion-transport applications.

Hydrogen Isotope Separation Using Graphene-Based Membranes in Liquid Water

Hydrogen isotope separation has been effectively achieved electrochemically by passage of gaseous H₂/D₂ through graphene/Nafion composite membranes. Nevertheless, deuteron nearly does not exist in the form of gaseous D₂ in nature but as liquid water. Thus, it is a more feasible way to separate and enrich deuterium from water. Herein, we have successfully transferred monolayer graphene to a rigid and porous polymer substrate, PITEM (polyimide track-etched membrane), which could avoid the swelling problem of the Nafion substrate as well as keep the integrity of graphene. Meanwhile, defects in the large area of CVD graphene could be successfully repaired by interfacial polymerization resulting in a high separation factor. Moreover, a new model was proposed for the proton transport mechanism through monolayer graphene based on the kinetic isotope effect (KIE). In this model, graphene plays a significant role in the H/D separation process by completely breaking the O-H/O-D bond, which can maximize the KIE, leading to increased H/D separation performance. This work suggests a promising application for using monolayer graphene in the industry and proposes a pronounced understanding of proton transport in graphene.

Giant Water Uptake Enabled Ultrahigh Proton Conductivity of Graphdiyne Oxide

Proton conductors have attracted great attention in various fields, especially in energy production. Here, we find that graphdiyne oxide (GDYO), derived from graphdiyne (GDY), features the highest proton conductivity of 0.54 S cm^-1 (100 % RH, 348 K) among the oxidized carbon allotropes reported so far. The sp- and sp² -co-hybridized carbon skeleton of GDY enables GDYO with the giant water uptake, which is 2.4 times larger than that of graphene oxide (GO), resulting in ultrahigh proton conductivity by increasing the proton concentration and proton conduction pathways. This ultrahigh proton conductivity of GDYO is further proved in a methanol fuel cell by using GDYO membrane as proton exchange membrane. The GDYO membrane enables the cell with higher open circuit voltage, larger power density and lower methanol permeability, compared with commercial Nafion 117. Moreover, the GDYO membrane bears high ion exchange capacity, good acidic stability and low swelling ratio.

Charge-induced proton penetration across two-dimensional clay materials

Two-dimensional clay materials possess superior thermal and chemical stability, and the intrinsic tubular channels in their atomic structure provide possible routes for proton penetration. Therefore, they are expected to overcome the lack of materials that can conduct protons between 100-500 °C. In this work, we investigated the detailed proton penetration mechanism across 2D clay nanosheets with different isomorphic substitutions and counterions using extensive ab initio molecular dynamics and metadynamics simulations. We found that the presence of negative surface charges can dramatically reduce the proton penetration energy barrier to about one-third that of the neutral case, making it a feasible choice for the design of next-generation high-temperature proton exchange membranes. By tuning the isomorphic substitutions, the proton conductivity of single-layer clay materials can be altered.

High-efficiency 2D nanosheet exfoliation by a solid suspension-improving method

Two-dimensional (2D) materials with mono or few layers have wide application prospects, including electronic, optoelectronic, and interface functional coatings in addition to energy conversion and storage applications. However, the exfoliation of such materials is still challenging due to their low yield, high cost, and poor ecological safety in preparation. Herein, a safe and efficient solid suspension-improving method was proposed to exfoliate hexagonal boron nitride nanosheets (hBNNSs) in a large yield. The method entails adding a permeation barrier layer in the solvothermal kettle, thus prolonging the contact time between the solvent and hexagonal boron nitride (hBN) nanosheet and improving the stripping efficiency without the need for mechanical agitation. In addition, the proposed method selectively utilizes a matching solvent that can reduce the stripping energy of the material and employs a high-temperature steam shearing process. Compared with other methods, the exfoliating yield ofhBNNSs is up to 42.3% at 150 °C for 12 h, and the strategy is applicable to other 2D materials. In application, the ionic conductivity of a PEO/hBNNSs composite electrolytes reached 2.18 × 10^-4S cm^-1at 60 °C. Overall, a versatile and effective method for stripping 2D materials in addition to a new safe energy management strategy were provided.

Dynamic Optical Visualization of Proton Transport Pathways at Water-Solid Interfaces

Probing proton transport is of vital importance for understanding cellular transport, surface catalysis and fuel cells. Conventional proton transport measurements rely on the use of electrochemical conductivity and do not allow for the direct visualization of proton transport pathways. The development of novel experimental techniques to spatiotemporally resolve proton transport is in high demand. Here, building upon the general conversion of aqueous proton flux into spatially resolved fluorescence signals, we optically visualize proton transport through nanopores and along hydrophilic interfaces. We observed that the fluorescence intensity increased at negative voltage due to lateral transport. Thanks to the temporal resolution of optical imaging, our technique further empowers the analysis of proton transport dynamics.

One-Atom-Thick Crystals as Emerging Proton Sieves

Two-dimensional (2D) crystals, despite their atomic thickness, have long been considered as impermeable membranes to all molecules and atoms under ambient conditions: even the smallest of atoms, hydrogen, is expected to take billions of years to penetrate the 2D lattice covered with dense electron clouds. Recently it has been found that monolayer graphene, hexagonal boron nitride, and some other one-atom-thick crystals are highly permeable to protons, raising fundamental questions about the details of the transport process. In this Perspective, we review the mechanism of proton transport through 2D crystals and the related room-temperature quantum effects; the potential applications of 2D membranes in proton-related separation and sieving techniques, including proton exchange membranes and hydrogen isotope separation; and factors that enhance proton permeation and in turn influence 2D membrane design.

Ion exchange in atomically thin clays and micas

The physical properties of clays and micas can be controlled by exchanging ions in the crystal lattice. Atomically thin materials can have superior properties in a range of membrane applications, yet the ion-exchange process itself remains largely unexplored in few-layer crystals. Here we use atomic-resolution scanning transmission electron microscopy to study the dynamics of ion exchange and reveal individual ion binding sites in atomically thin and artificially restacked clays and micas. We find that the ion diffusion coefficient for the interlayer space of atomically thin samples is up to 10⁴ times larger than in bulk crystals and approaches its value in free water. Samples where no bulk exchange is expected display fast exchange at restacked interfaces, where the exchanged ions arrange in islands with dimensions controlled by the moiré superlattice dimensions. We attribute the fast ion diffusion to enhanced interlayer expandability resulting from weaker interlayer binding forces in both atomically thin and restacked materials. This work provides atomic scale insights into ion diffusion in highly confined spaces and suggests strategies to design exfoliated clay membranes with enhanced performance.

Subatomic species transport through atomically thin membranes: Present and future applications

[Figure: see text].

Facile Fabrication of Subnanopores in Graphene under Ion Irradiation: Molecular Dynamics Simulations

Two-dimensional (2D) nanoporous membranes have attracted great interest in water desalination, energy conversion, electrode, and gas separation. The performances of these membranes are mainly determined by the nanopores, and only with satisfactory subnanometer pores can applications such as high-precision ion separation be realized. Therefore, to efficiently create subnanopores in 2D materials is of great importance. Here, using molecular dynamics simulations, we demonstrate that the direct irradiation of energetic ion is capable of introducing subnanopores in monolayer graphene. By changing the energy of the incident Au ion, the averaged pore diameter can be adjusted from 4.2 to 5.6 Å, and pore diameter distributions are narrow. In the formation processes of the subnanopores, the cascade collisions caused by the primary knock-on atom (PKA) predominates, and pores can only be created in ion impact positions close to the PKA, especially for the incident ion with high energy. Our results show the promise of ion irradiation as a facile method to fabricate subnanopores in 2D materials. As hydrated ions, gases, and small organic molecules have diameters of several angstroms, close to the pore sizes, the created nanoporous membranes can be used to separate those matter, which is conducive to accelerating related applications.

‘Proton escalator’ PEI and phosphotungstic acid containing nanofiber membrane with remarkable proton conductivity

Polyethyleneimine (PEI) and phosphotungstic acid (HPW) build an efficient proton transmission path. The segmental movement of flexible PEI speeds up the migration of protons, which acts as a ‘proton-escalator’.

Argentophilicity induced anomalous thermal expansion behavior in a 2D silver squarate

A 2D bilayer coordination polymer has been found to exhibit colossal interlayer PTE and in-plane NTE owing to argentophilic interactions.

Selective Proton Transport for Hydrogen Production Using Graphene Oxide Membranes

Graphene oxide has shown exceptional properties in terms of water permeability and filtration characteristics. Here the suitability of graphene oxide membranes for the spatial separation of hydronium and hydroxide ions after photocatalytic water splitting is demonstrated. Instead of relying on classical size exclusion by adjusting the membrane laminates' interlayer spacings, nonmodified graphene oxide is used to exploit the presence of its natural functional groups and surface charges for filtration. Despite a significantly larger interlayer spacing inside the membrane compared with the size of the hydrated radii of the ions, highly asymmetric transport behavior and a 6 times higher mobility for hydronium than for hydroxide are observed. DFT simulations reveal that hydroxide ions are more prone to interact and stick to the functional groups of graphene oxide, while diffusion of hydronium ions through the membrane is less impeded and aligns well with the concept of the Grotthuss mechanism.