Non-negligible Water-permeance through Nanoporous Ion Exchange Medium

Analyte Enrichment via Ion Concentration Polarization with Hydrogel Plugs Polymerized in PDMS Microchannels by a Facile and Comprehensive Method for Improved Polymerization

Hydrogels are incorporated into microfluidic devices to provide enhanced functionality by enabling processes such as enzyme immobilization, sample enrichment, and ionic current rectification. However, in the microfluidic devices with the commonly used material poly(dimethylsiloxane) (PDMS), hydrogels are very difficult to polymerize in situ in an ambient atmosphere because of the high oxygen concentration in PDMS. Even with very high (1.8%) photoinitiator concentrations, the polymerized hydrogel does not completely fill the microchannel. Here, we report a facile and broadly applicable protocol that utilizes microchannel pretreatment with 20% benzophenone in acetone to provide a hydrogel plug that completely fills the microchannel cross section by consuming the oxygen in the PDMS substrate near the microchannel wall. Both negatively charged and neutral hydrogels are polymerized from monomer solutions that utilize the photoinitiator/solvent combinations of VA-086 in water and benzophenone or IRG in DMSO. The photoinitiators were tested at different concentrations and in devices with different levels of oxidation. The hydrogel morphology is characterized using phase contrast microscopy and is related to the hydrogel's performance for concentration enrichment and ionic current rectification. A novel method is employed to confine the precursor solution in desired locations so that a photomask is not required for the spatial control of the plug location. Among six hydrogel formulations, at 100 V, the best current rectification factor obtained is ∼600 and the best analyte enrichment achieved is ∼120-fold in 5 min. This method provides a rapid and simple approach to increase the capabilities of PDMS microfluidic devices through improved polymerization of nanoporous hydrogels.

On the evolution of the exclusion zone produced by hydrophilic surfaces: A contracted description

After exciting scientific debates about its nature, the development of the exclusion zone, a region near hydrophilic surfaces from which charged colloidal particles are strongly expelled, has been finally traced back to the diffusiophoresis produced by unbalanced ion gradients. This was done by numerically solving the coupled Poisson equation for electrostatics, the two stationary Stokes equations for low Reynolds numbers in incompressible fluids, and the Nernst-Planck equation for mass transport. Recently, it has also been claimed that the leading mechanism behind the diffusiophoretic phenomenon is electrophoresis [Esplandiu et al., Soft Matter 16, 3717 (2020)]. In this paper, we analyze the evolution of the exclusion zone based on a one-component interaction model at the Langevin equation level, which leads to simple analytical expressions instead of the complex numerical scheme of previous works, yet being consistent with it. We manage to reproduce the evolution of the exclusion zone width and the mean-square displacements of colloidal particles we measure near Nafion, a perfluorinated polymer membrane material, along with all characteristic time regimes, in a unified way. Our findings are also strongly supported by complementary experiments using two parallel planar conductors kept at a fixed voltage, mimicking the hydrophilic surfaces, and some computer simulations.

ExoCAS-2: Rapid and Pure Isolation of Exosomes by Anionic Exchange Using Magnetic Beads

Extracellular vesicles (EVs) are considered essential biomarkers in liquid biopsies. Despite intensive efforts aimed at employing EVs in a clinical setting, workable approaches are currently limited owing to the fact that EV-isolation technologies are still in a nascent stage. This study introduces a magnetic bead-based ion exchange platform for isolating EVs called ExoCAS-2 (exosome clustering and scattering). Owing to their negative charge, exosomes can easily adhere to magnetic beads coated with a polycationic polymer. Owing to the features of magnetic beads, exosomes can be easily processed via washing and elution steps and isolated with high purity and yield within 40 min. The present results confirmed the isolation of exosomes through analyses of size distribution, morphology, surface and internal protein markers, and exosomal RNA. Compared with the commercially available methods, the proposed method showed superior performance in terms of key aspects, including operation time, purity, and recovery rate. This highlights the potential of this magnetic bead-based ion exchange platform for isolating exosomes present in blood plasma.

Continuous and spontaneous nanoparticle separation by diffusiophoresis

The separation of nanoparticles has drawn critical attention in various microfluidic applications including chemical analysis, diagnostics and environmental monitoring. Thus, a number of nanoparticle separation methods have been extensively proposed. However, most of the conventional methods require complicated structured devices, expensive manufacturing processes, and external power sources. While a spontaneous diffusiophoretic separation device based on an ion exchange mechanism could overcome such drawbacks, the recovery of separated particles and the inevitable development of an acidic environment due to the release of H+ from the cation exchange membrane limit its practical applicability. Therefore, in this work, we present a simple but robust nanoparticle separation method based on spontaneously induced diffusiophoresis, which is operated in a continuous manner to overcome the limitations of conventional methods. First, we confirmed that the particle exclusion distance followed the previously developed scaling law of diffusiophoresis. Consequently, we demonstrated the separation of nanoparticles of 40 nm, 200 nm and 2 μm diameter by utilizing the fact that the exclusion distances of various particles were proportional to their diffusiophoretic mobility. Furthermore, the use of Tris buffer increased the diffusiophoretic migration of nanoparticles due to the enhanced concentration gradient, and enabled the produced solution to be compatible with pH-sensitive bio-samples. Therefore, we expect this continuous and spontaneous diffusiophoretic separation platform to be useful in practical applications for analyzing various nano-meter scale bio-particles.

Cells in New Light: Ion Concentration, Voltage, and Pressure Gradients across a Hydrogel Membrane

The ionic compositions of the intra- and extracellular environments are distinct from one another, with K⁺ being the main cation in the cytosol and Na⁺ being the most abundant cation outside of the cell. Specific ions can permeate into and out of the cell at different rates, bringing about uneven distribution of charges and development of negative electric potential inside the cell. Each healthy cell must maintain a specific ion concentration gradient and voltage. To account for these functions, various ionic pumps and channels located within the cell membrane have been invoked. In this work, we use a porous alginate hydrogel as a model gelatinous network representing the plant cell wall or cytoskeleton of the animal cell. We show that the gel barrier is able to maintain a stable separation of ionic solutions of different ionic strengths and chemical compositions without any pumping activity. For the Na⁺/K⁺ concentration gradient sustained across the barrier, a negative electric potential develops within the K⁺-rich side. The situation is reminiscent of that in the cell. Furthermore, also the advective flow of water molecules across the gel barrier is restricted, despite the gel's large pores and the osmotic or hydrostatic pressure gradients across it. This feature has important implications for osmoregulation. We propose a mechanism in which charge separation and electric fields developing across the permselective (gel) membrane prevent ion and bulk fluid flows ordinarily driven by chemical and pressure gradients.

Investigation on the Stability of Random Vortices in an Ion Concentration Polarization Layer with Imposed Normal Fluid Flow

While nanoscale electrokinetic studies based on ion concentration polarization has been actively researched recently, random vortices naturally occur, leading to significantly destabilize in laboratory experiments or practical applications. These random vortices agitate the fluid inside microchannels and let the sample molecules seriously leak out preventing them from being controlled. Therefore, several trials have been reported to regulate those uninvited fluctuations by fluid flow tangential to a nanoporous membrane. Indeed, the influence of normal flow should be studied since the mass transport happens in the normal direction to the membrane. Thus, in this work, the nonlinear influence of normal flow to the instability near ion-selective surface was investigated by fully-coupled direct numerical simulation using COMSOL Multiphysics. The investigation on the effect of normal flow revealed that a space charge layer plays a significant role in the onset and growth of instability. The normal flow from the reservoir into the ion-selective surface pushed the space charge layer and decreased the size of vortices. However, there existed a maximum point for the growth of instability. The squeeze of the space charge layer increased the gradient of ion concentration in the layer, which resulted in escalating the velocity of vortices. On the other hand, the normal flow from the ion-selective surface into the reservoir suppressed the instability by spreading ions in the expanding space charge layer, leading to the reduction of ion concentration delayed the onset of instability. These two different mechanisms rendered asymmetric transition of stability as a function of the Peclet number and applied voltage. Therefore, this investigation would help understand the growth of instability and control the inevitable random vortices for the inhibition of fluid-agitation and leakage.

Effect of evaporation through nanoporous medium on diffusiophoresis

Diffusiophoresis near a nanoporous medium is the phenomenon that particles were spontaneously moved from low concentration region to high concentration region. However, unidirectional particle motion impeded further application of this phenomenon and lack of studies about the external convective flow effect such as evaporation through a nanoporous medium were reported. In this work, we investigated the evaporation effect through a nanoporous medium on spontaneous particle exclusion zone induced by diffusiophoresis. Consequently, particle’s motion was divided into three regimes: diffusiophoresis regime, transition regime, and evaporation regime depending on the evaporation effect. The experiment in which the time of initiating evaporation effect was controlled by adjusting the region of PDMS on a nanoporous medium showed that evaporation plays a critical role in studying the spontaneous particle exclusion zone. This rigorous analysis would provide a useful strategy for optimizing a spontaneous particle preconcentration/detection platform.

Spontaneous diffusiophoretic separation in paper-based microfluidic device

Microfluidic paper-based analytical devices (μPADs) for separating particles have been playing a key role for point-of-care diagnostics in the area of remote settings. While splendid separation methods using μPADs have been explosively developed, they still require external devices inducing external field. In this work, the spontaneous separation method in μPADs was suggested by leveraging convective flow (the imbibition of paper and nanoporous medium) and diffusiophoresis by ion exchange medium. Especially, the paper’s fast imbibition was utilized as driving particles at the first stage, which results in fast overall processing in contrast to the spontaneous separation method of microfluidic chip integrated with only ion exchange medium. Therefore, our novel spontaneous selective preconcentration method based on μPADs would have key potential to be used in portable point-of-care devices in remote settings.

Electrode-Free Concentration and Recovery of DNA at Physiologically Relevant Ionic Concentrations

Advances in microanalytical and microfluidic technologies have enabled rapid and amplification-free detection of DNA with a high signal-to-noise ratio. The low sample volume, however, poses a limit in the DNA detection sensitivity, which can be challenging for analyzing rare DNA in physiological samples. One way to improve the sensitivity is to concentrate the DNA in the sample prior to the analysis. The most common DNA concentration techniques are based on electrokinetics, which require an external electric field and generally become ineffective in high ionic concentration conditions. In this work, we present a facile method termed high-salt molecular rheotaxis (HiSMRT) to concentrate and recover DNA from samples with physiologically relevant ionic concentrations without any external electric field. HiSMRT requires only pressure-driven flow and ion concentration gradient to induce a stable local electric field and achieve DNA concentration, making it impervious to high ionic concentrations. We demonstrate that HiSMRT performs robustly at ionic concentrations equivalent to 2%-20% of the ionic concentration in blood serum. HiSMRT can concentrate DNA by up to 960-fold and recover an average of 96.4% of the DNA fragments from 2.0 to 23 kbp uniformly. The concentration process using HiSMRT takes as little as 7.5 min. Moreover, we show that this technique can be easily integrated to perform DNA concentration, size separation, and single-molecule detection all in one platform. We anticipate that this technique will be applicable to a wide range of biological samples and will help to improve the sensitivity of nucleic acid detection for low-abundance DNA biomarkers.

Controllable pH Manipulations in Micro/Nanofluidic Device Using Nanoscale Electrokinetics

Recently introduced nanoscale electrokinetic phenomenon called ion concentration polarization (ICP) has been suffered from serious pH changes to the sample fluid. A number of studies have focused on the origin of pH changes and strategies for regulating it. Instead of avoiding pH changes, in this work, we tried to demonstrate new ways to utilize this inevitable pH change. First, one can obtain a well-defined pH gradient in proton-received microchannel by applying a fixed electric current through a proton exchange membrane. Furthermore, one can tune the pH gradient on demand by adjusting the proton mass transportation (i.e., adjusting electric current). Secondly, we demonstrated that the occurrence of ICP can be examined by sensing a surrounding pH of electrolyte solution. When pH > threshold pH, patterned pH-responsive hydrogel inside a straight microchannel acted as a nanojunction to block the microchannel, while it did as a microjunction when pH < threshold pH. In case of forming a nanojunction, electrical current significantly dropped compared to the case of a microjunction. The strategies that presented in this work would be a basis for useful engineering applications such as a localized pH stimulation to biomolecules using tunable pH gradient generation and portable pH sensor with pH-sensitive hydrogel.

Hierarchical micro/nanoporous ion-exchangeable sponge

Inspired by the versatile properties of a sponge, we propose an ion-exchangeable sponge composed of hierarchical micropores and nanopores for water treatment. Sodium ions in brackish water (10-300 mM) absorbed in the sponge were exchanged for hydrogen ions in a short incubation time and the desalted water was released by squeezing the sponge with a single hand grip. This simple desalination process was attributed to the multi-scale porous structures in the sponge. A number of nanoporous thin films were formed like bubbles surrounded by the closed backbone of the microporous sponge. The hierarchical micro/nanopores maximized the contact area of the ion-exchanging surface with the saline solution so that scaled-up desalination was achieved. Furthermore, the growth of wheat shoots in the desalted water was demonstrated in vivo after using this micro/nanofluidic based water-treatment with the sponges. Wheat shoots grown in NaHCO₃/Na₂CO₃ solutions treated by the sponges were 110 to 226.45% longer than those grown in the original salty water. This implies that the ion-exchangeable sponge could serve as an appropriate technology for the treatment of ground water affected by acid rain and weathered alkaline rocks.

Nanoelectrokinetic bufferchannel-less radial preconcentrator and online extractor by tunable ion depletion layer

Among various preconcentration strategies using nanofluidic platforms, a nanoscale electrokinetic phenomenon called ion concentration polarization (ICP) has been extensively utilized due to several advantages such as high preconcentration factor and no need of complex buffer exchange process. However, conventional ICP preconcentrator had difficulties in the recovery of preconcentrated sample and complicated buffer channels. To overcome these, bufferchannel-less radial micro/nanofluidic preconcentrator was developed in this work. Radially arranged microchannel can maximize the micro/nano membrane interface so that the samples were preconcentrated from each microchannel. All of preconcentrated plugs moved toward the center pipette tip and can be easily collected by just pulling out the tip installed at the center reservoir. For a simple and cost-effective fabrication, a commercial printer was used to print the nanoporous membrane as "Nafion-junction device." Various analytes such as polystyrene particle, fluorescent dye, and dsDNA were preconcentrated and extracted with the recovery ratio of 85.5%, 79.0%, and 51.3%, respectively. Furthermore, we used a super inkjet printer to print the silver electrode instead of nanoporous membrane to preconcentrate either type of charged analytes as "printed-electrode device." A Faradaic reaction was used as the main mechanism, and we successfully demonstrated the preconcentration of either negatively or positively charged analytes. The presented bufferchannel-less radial preconcentrator would be utilized as a practical and handy platform for analyzing low-abundant molecules.

Spontaneous Selective Preconcentration Leveraged by Ion Exchange and Imbibition through Nanoporous Medium

Manipulating mechanism of particle’s motion has been extensively studied for the sample preparation in microfluidic applications including diagnostics, food industries, biological analyses and environmental monitoring. However, most of conventional methods need additional external forces such as electric field or pressure and complicated channel designs, which demand highly complex fabrication processes and operation strategies. In addition, these methods have inherent limitations of dilution or mixing during separation or preconcentration step, respectively, so that a number of studies have reported an efficient selective preconcentration process, i.e. conducting the separation and preconcentration simultaneously. In this work, a power-free spontaneous selective preconcentration method was suggested based on leveraging convective flow over diffusiophoresis near the water-absorbing nanoporous ion exchange medium, which was verified both by simulation and experiment. Especially, the velocity of the convective flow by an imbibition deviated from the original tendency of t^−1/2 due to non-uniformly patterned nanoporous medium that has multiple cross-sectional areas. As a result, the direction of particle’s motion was controlled at one’s discretion, which led to the spontaneous selective preconcentration of particles having different diffusiophoretic constant. Also, design rule for maximizing the efficiency was recommended. Thus, this selective preconcentration method would play as a key mechanism for power-free lab on a chip applications.