Recovering metals from aqueous solutions by biosorption onto phosphorylated dry baker's yeast

Spent brewer's yeast as a selective biosorbent for metal recovery from polymetallic waste streams

While the amount of electronic waste is increasing worldwide, the heterogeneity of electronic scrap makes the recycling very complicated. Hydrometallurgical methods are currently applied in e-waste recycling which tend to generate complex polymetallic solutions due to dissolution of all metal components. Although biosorption has previously been described as a viable option for metal recovery and removal from low-concentration or single-metal solutions, information about the application of selective metal biosorption from polymetallic solutions is missing. In this study, an environmentally friendly and selective biosorption approach, based on the pH-dependency of metal sorption processes is presented using spent brewer's yeast to efficiently recover metals like aluminum, copper, zinc and nickel out of polymetallic solutions. Therefore, a design of experiment (DoE) approach was used to identify the effects of pH, metal, and biomass concentration, and optimize the biosorption efficiency for each individual metal. After process optimization with single-metal solutions, biosorption experiments with lyophilized waste yeast biomass were performed with synthetic polymetallic solutions where over 50% of aluminum at pH 3.5, over 40% of copper at pH 5.0 and over 70% of zinc at pH 7.5 could be removed. Moreover, more than 50% of copper at pH 3.5 and over 90% of zinc at pH 7.5 were recovered from a real polymetallic waste stream after leaching of printed-circuit boards. The reusability of yeast biomass was confirmed in five consecutive biosorption steps with little loss in metal recovery abilities. This proves that spent brewer's yeast can be sustainably used to selectively recover metals from polymetallic waste streams different to previously reported studies.

Copper Tolerance of Novel Rhodotorula sp. Yeast Isolated from Gold Mining Ore in Gia Lai, Vietnam

In this study, twenty-five yeast strains were isolated from soil samples collected in the gold mining ore in Gia Lai, Vietnam. Among them, one isolate named GL1T could highly tolerate Cu2+ up to 10 mM, and the isolates could also grow in a wide range of pH (3-7), and temperature (10-40 °C). Dried biomass of GL1 was able to remove Cu2+ effectively up to 90.49% with a maximal biosorption capacity of 18.1 mg/g at pH 6, temperature 30 °C, and incubation time 60 min. Sequence analysis of rDNA indicated this strain was closely related to Rhodotorula mucilaginosa but with 1.53 and 3.46% nucleotide differences in the D1/D2 domain of the 28S rRNA gene and the ITS1-5.8S rRNA gene-ITS2 region sequence, respectively. Based on phylogenetic tree analysis and the biochemical characteristics, the strain appears to be a novel Rhodotorula species, and the name Rhodotorula aurum sp. nov. is proposed. This study provides us with more information about heavy metal-tolerant yeasts and it may produce a new tool for environmental control and metal recovery operations.

Stripped: contribution of cyanobacterial extracellular polymeric substances to the adsorption of rare earth elements from aqueous solutions

The transformation of modern industries towards enhanced sustainability is facilitated by green technologies that rely extensively on rare earth elements (REEs) such as cerium (Ce), neodymium (Nd), terbium (Tb), and lanthanum (La). The occurrence of productive mining sites, e.g., is limited, and production is often costly and environmentally harmful. As a consequence of increased utilization, REEs enter our ecosystem as industrial process water or wastewater and become highly diluted. Once diluted, they can hardly be recovered by conventional techniques, but using cyanobacterial biomass in a biosorption-based process is a promising eco-friendly approach. Cyanobacteria can produce extracellular polymeric substances (EPS) that show high affinity to metal cations. However, the adsorption of REEs by EPS has not been part of extensive research. Thus, we evaluated the role of EPS in the biosorption of Ce, Nd, Tb, and La for three terrestrial, heterocystous cyanobacterial strains. We cultivated them under N-limited and non-limited conditions and extracted their EPS for compositional analyses. Subsequently, we investigated the metal uptake of a) the extracted EPS, b) the biomass extracted from EPS, and c) the intact biomass with EPS by comparing the amount of sorbed REEs. Maximum adsorption capacities for the tested REEs of extracted EPS were 123.9-138.2 mg g-1 for Komarekiella sp. 89.12, 133.1-137.4 mg g-1 for Desmonostoc muscorum 90.03, and 103.5-129.3 mg g-1 for Nostoc sp. 20.02. A comparison of extracted biomass with intact biomass showed that 16% (Komarekiella sp. 89.12), 28% (Desmonostoc muscorum 90.03), and 41% (Nostoc sp. 20.02) of REE adsorption was due to the biosorption of the extracellular EPS. The glucose- rich EPS (15%-43% relative concentration) of all three strains grown under nitrogen-limited conditions showed significantly higher biosorption rates for all REEs. We also found a significantly higher maximum adsorption capacity of all REEs for the extracted EPS compared to cells without EPS and untreated biomass, highlighting the important role of the EPS as a binding site for REEs in the biosorption process. EPS from cyanobacteria could thus be used as efficient biosorbents in future applications for REE recycling, e.g., industrial process water and wastewater streams.

The Remediation of Dysprosium-Containing Effluents Using Cyanobacteria Spirulina platensis and Yeast Saccharomyces cerevisiae

Dysprosium is one of the most critical rare earth elements for industry and technology. A comparative study was carried out to assess the biosorption capacity of cyanobacteria Spirulina platensis and yeast Saccharomyces cerevisiae toward dysprosium ions. The effect of experimental parameters such as pH, dysprosium concentration, time of contact, and temperature on the biosorption capacity was evaluated. Biomass before and after dysprosium biosorption was analyzed using neutron activation analysis and Fourier-transform infrared spectroscopy. For both biosorbents, the process was quick and pH-dependent. The maximum removal of dysprosium using Spirulina platensis (50%) and Saccharomyces cerevisiae (68%) was attained at pH 3.0 during a one-hour experiment. The adsorption data for both biosorbents fitted well with the Langmuir isotherm model, whereas the kinetics of the process followed the pseudo-second-order and Elovich models. The maximum biosorption capacity of Spirulina platensis was 3.24 mg/g, and that of Saccharomyces cerevisiae was 5.84 mg/g. The thermodynamic parameters showed that dysprosium biosorption was a spontaneous process, exothermic for Saccharomyces cerevisiae and endothermic for Spirulina platensis. Biological sorbents can be considered an eco-friendly alternative to traditional technologies applied for dysprosium ion recovery from wastewater.

Biofabricated yeast: super-soldier for detoxification of heavy metals

The advances in nanotechnology have shown enormous impacts in environmental technology as a potent weapon for degradation of toxic organic pollutants and detoxification of heavy metals. It is either by in-situ or ex-situ adaptive strategies. Mycoremediation of environmental pollutants has been a success story of the past decade, by employing the wide arsenal of biological capabilities of fungi. Recently, the proficiency and uniqueness of yeast cell surface alterations have encouraged the generation of engineered yeast cells as dye degraders, heavy metal reduction and its recovery, and also as detoxifiers of various hazardous xenobiotic compounds. As a step forward, recent trends in research are towards developing biologically engineered living materials as potent, biocompatible and reusable hybrid nanomaterials. They include chitosan-yeast nanofibers, nanomats, nanopaper, biosilica hybrids, and TiO₂-yeast nanocomposites. The nano-hybrid materials contribute significantly as supportive stabilizer, and entrappers, which enhances the biofabricated yeast cells' functionality. This field serves as an eco-friendly cutting-edge cocktail research area. In this review, we highlight recent research on biofabricated yeast cells and yeast-based biofabricated molecules, as potent heavy metals, toxic chemical detoxifiers, and their probable mechanistic properties with future application perspectives.

A review of the application of fungi as an effective and attractive bio-adsorbent for biosorption of heavy metals from wastewater

One of the most hazardous environmental pollutants is the pollution risen by heavy metal ions in effluents, which is increasing due to the increasing human activity and the development of urbanization. Notwithstanding the economic challenges to control the pollution of effluent treatment processes, it seems necessary to provide effective approaches. The sorption method is widely used due to low-cost, flexibility in design and operation, repeatability, and significant performance. Hence, the need for more environmentally friendly sorbents to eliminate metal ions is greater than ever. Due to the unique features such as the presence of chitin and chitosan in the cell wall, high absorption capacity, environmental friendliness, availability, and cheapness, the use of fungi as adsorbent has received much attention. Therefore, this work tries to address the use of fungi as biosorbents to remove these metals, the dangers of heavy metals, and their sources. Moreover, equilibrium, kinetic, and thermodynamic behaviors of the heavy metal ion adsorption process in the literature are briefly studied.

Microbial recovery of critical metals from secondary sources

The continuous development of technologies involving critical metals, both in Europe and over the world, and geopolitical challenges in areas rich in critical metal sources, imposed increased research efforts to recover them from secondary sources, by eco-efficient processes. Yet, microbes-metal interactions are not sufficiently exploited to recover metals from secondary sources, although they are already used in ore extraction. This review examines and compare strategies and processes involving microorganisms for critical metals recovery, since conventional physico-chemical methods are energy-intensive and often polluting. Two groups of microbial assisted recovery processes are discussed: metal mobilization from metal bearing waste, and selective metal separation from leaching solutions by immobilization on microbial biomass. Because most of the identified microbial technologies are developed on laboratory scale, the increase of biorecovery efficiency is compulsory for enhancing scaling-up potential. Future developments focused on novel microorganisms and high-performance strategies for critical metal recovery by microbial processes are considered.

Innovative method for encapsulating highly pigmented biomass from Aspergillus nidulans mutant for copper ions removal and recovery

Biosorption has been considered a promising technology for the treatment of industrial effluents containing heavy metals. However, the development of a cost-effective technique for biomass immobilization is essential for successful application of biosorption in industrial processes. In this study, a new method of reversible encapsulation of the highly pigmented biomass from Aspergillus nidulans mutant using semipermeable cellulose membrane was developed and the efficiency of the encapsulated biosorbent in the removal and recovery of copper ions was evaluated. Data analysis showed that the pseudo-second-order model better described copper adsorption by encapsulated biosorbent and a good correlation (r2 > 0.96) to the Langmuir isotherm was obtained. The maximum biosorption capacities for the encapsulated biosorbents were higher (333.5 and 116.1 mg g-1 for EB10 and EB30, respectively) than that for free biomass (92.0 mg g-1). SEM-EDXS and FT-IR analysis revealed that several functional groups on fungal biomass were involved in copper adsorption through ion-exchange mechanism. Sorption/desorption experiments showed that the metal recovery efficiency by encapsulated biosorbent remained constant at approximately 70% during five biosorption/desorption cycles. Therefore, this study demonstrated that the new encapsulation method of the fungal biomass using a semipermeable cellulose membrane is efficient for heavy metal ion removal and recovery from aqueous solutions in multiple adsorption-desorption cycles. In addition, this reversible encapsulation method has great potential for application in the treatment of heavy metal contaminated industrial effluents due to its low cost, the possibility of recovering adsorbed ions and the reuse of biosorbent in consecutive biosorption/desorption cycles with high efficiency of metal removal and recovery.

Towards rare earth element recovery from wastewaters: biosorption using phototrophic organisms

Abstract

Whilst the biosorption of metal ions by phototrophic (micro)organisms has been demonstrated in earlier and more recent research, the isolation of rare earth elements (REEs) from highly dilute aqueous solutions with this type of biomass remains largely unexplored. Therefore, the selective binding abilities of two microalgae (Calothrix brevissima, Chlorella kessleri) and one moss (Physcomitrella patens) were examined using Neodym and Europium as examples. The biomass of P. patens showed the highest sorption capacities for both REEs (Nd³⁺: 0.74 ± 0.05 mmol*g⁻¹; Eu³⁺: 0.48 ± 0.05 mmol*g⁻¹). A comparison with the sorption of precious metals (Au³⁺, Pt⁴⁺) and typical metal ions contained in wastewaters (Pb²⁺, Fe²⁺, Cu²⁺, Ni²⁺), which might compete for binding sites, revealed that the sorption capacities for Au³⁺ (1.59 ± 0.07 mmol*g⁻¹) and Pb²⁺ (0.83 ± 0.02 mmol*g⁻¹) are even higher. Although different patterns of maximum sorption capacities for the tested metal ions were observed for the microalgae, they too showed the highest affinities for Au³⁺, Pb²⁺, and Nd³⁺. Nd-sorption experiments in the pH range from 1 to 6 and the recorded adsorption isotherms for this element showed that the biomass of P. patens has favourable properties as biosorbent compared to the microalgae investigated here. Whilst the cultivation mode did not influence the sorption capacities for the target elements of the two algal species, it had a great impact on the properties of the moss. Thus, further studies are necessary to develop effective biosorption processes for the recovery of REEs from alternative and so far unexploited sources.

Key points

• The highest binding capacity for selected REEs was registered for P. patens.

• The highest biosorption was found for Au and the biomass of the examined moss.

• Biosorption capacities of P. patens seem to depend on the cultivation mode.

Assessment of marine macroalgae potential for gadolinium removal from contaminated aquatic systems

Gadolinium (Gd) is a rare earth associated with hospital and urban wastewaters due to its application as a contrast agent for magnetic resonance imaging. In this work, the uptake of Gd from contaminated seawater by three living marine macroalgae, Ulva lactuca (Chlorophyta), Fucus spiralis (Phaeophyta) and Gracilaria sp. (Rhodophyta) was studied along 72 h. Surface analysis (FTIR), water content, kinetic modelling, and Gd quantification in seawater and biomass were performed. All species were able to accumulate Gd from seawater with 10, 157, and 500 μg Gd L^-1, although green and red macroalgae performed better, following the order: green > red > brown. Removal efficiencies reached 85%, corresponding to a bioconcentration factor of 1700. In more complex solutions that intended to mimic real contaminated environments, namely mixtures with other rare earth elements (Y, La, Ce, Pr, Nd, Eu, Tb, Dy), and with potentially toxic elements commonly found in wastewaters (Cr, Ni, Cu, Cd, Hg, Pb), at two salinities (10 and 30), the macroalgae kept its efficiency: 84% and 88% of removal by green and red macroalgae, respectively. Overall, findings evidence that living macroalgae could be a countermeasure to the increasing anthropogenic enrichment of Gd observed in the aquatic environment.

Biosorption: A Review of the Latest Advances

Biosorption is a variant of sorption techniques in which the sorbent is a material of biological origin. This technique is considered to be low cost and environmentally friendly, and it can be used to remove pollutants from aqueous solutions. The objective of this review is to report on the most significant recent works and most recent advances that have occurred in the last couple of years (2019–2020) in the field of biosorption. Biosorption of metals and organic compounds (dyes, antibiotics and other emerging contaminants) is considered in this review. In addition, the use and possibilities of different forms of biomass (live or dead, modified or immobilized) are also considered.

Biological, biomolecular, and bio-inspired strategies for detection, extraction, and separations of lanthanides and actinides

Lanthanides and actinides are elements of ever-increasing technological importance in the modern world. However, the similar chemical and physical properties within these groups make purification of individual elements a challenge. Current industrial standards for the extraction, separation, and purification of these metals from natural sources, recycled materials, and industrial waste are inefficient, relying upon harsh conditions, repetitive steps, and ligands with only modest selectivity. Biological, biomolecular, and bio-inspired strategies towards improving these separations and making them more environmentally sustainable have been researched for many years; however, these methods often have insufficient selectivity for practical application. Recent developments in the understanding of how lanthanides are selectively acquired and used by certain bacteria offer the opportunity for a newer, more efficient take on these designs, as well as the possibility for fundamentally new designs and strategies. Herein, we review current cell-based and biomolecular (primarily small-molecule and protein-based) methods for detection, extraction, and separations of f-block elements. We discuss how the increasing knowledge regarding the selective recognition, uptake, trafficking, and storage of these elements in biological systems has informed and will continue to promote development of novel approaches to achieve these ends.

Mineralization induced by phosphorylated dry baker's yeast

We found the mineralization of Cu during long-term Cu2+ adsorption onto dry baker's yeast cells phosphorylated using sodium cyclo-triphosphate. Field emission scanning electron microscopy (FESEM) with energy-dispersive X-ray spectroscopy confirmed that the elemental composition of minerals were copper, phosphorus, and oxygen. Synchrotron-based X-ray absorption fine structure showed that the local structure around Cu atoms deposited on the mineral was almost identical to that of commercial copper (II) phosphate Cu3(PO4)2∙3H2O. However, the crystallinity was low, and the structure was slightly distorted. Time profile analysis using FESEM revealed that copper phosphate mineralization was first apparent on Day 3 of adsorption, whereas mineral formation plateaued at around Day 7. It seems that mineralization occurs by the local saturation of phosphate and Cu2+ on the yeast cells. Mineralization of the rare earth ion Dy3+ was also demonstrated during long-term adsorption. Mineralization on phosphorylated yeast cells appears to follow a common path for various types of metal ions and provides a promising technique for metal recovery via irreversible adsorption.

An overview on heavy metal resistant microorganisms for simultaneous treatment of multiple chemical pollutants at co-contaminated sites, and their multipurpose application

Anthropogenic imbalance of chemical pollutants in environment raises serious threat to all life forms. Contaminated sites often possess multiple heavy metals and other types of pollutants. Elimination of chemical pollutants at co-contaminated sites is imperative for the safe ecosystem functions, and simultaneous removal approach is an attractive scheme for their remediation. Different conventional techniques have been applied as concomitant treatment solution but fall short at various parameters. In parallel, use of microorganisms offers an innovative, cost effective and ecofriendly approach for simultaneous treatment of various chemical pollutants. However, microbiostasis due to harmful effects of heavy metals or other contaminants is a serious bottleneck facing remediation practices in co-contaminated sites. But certain microorganisms have unique mechanisms to resist heavy metals, and can act on different noxious wastes. Considering this significant, my review provides information on different heavy metal resistant microorganisms for bioremediation of different chemical pollutants, and other assistance. In this favour, the integrated approach of simultaneous treatment of multiple heavy metals and other environmental contaminants using different heavy metal resistant microorganisms is summarized. Further, the discussion also intends toward the use of heavy metal resistant microorganisms associated with industrial and environmental applications, and healthcare. PREFACE: Simultaneous treatment of multiple chemical pollutants using microorganisms is relatively a new approach. Therefore, this subject was not well received for review before. Also, multipurpose application of heavy metal microorganisms has certainly not considered for review. In this regard, this review attempts to gather information on recent progress on studies on different heavy metal resistant microorganisms for their potential of treatment of co-contaminated sites, and multipurpose application.

Study of the bioremediatory capacity of wild yeasts

Microbial detoxification has been proposed as a new alternative for removing toxins and pollutants. In this study, the biodetoxification activities of yeasts against aflatoxin B₁ and zinc were evaluated by HPLC and voltammetric techniques. The strains with the best activity were also subjected to complementary assays, namely biocontrol capability and heavy-metal resistance. The results indicate that the detoxification capability is toxin- and strain-dependent and is not directly related to cell growth. Therefore, we can assume that there are some other mechanisms involved in the process, which must be studied in the future. Only 33 of the 213 strains studied were capable of removing over 50% of aflatoxin B₁, Rhodotrorula mucilaginosa being the best-performing species detected. As for zinc, there were 39 strains that eliminated over 50% of the heavy metal, with Diutina rugosa showing the best results. Complementary experiments were carried out on the strains with the best detoxification activity. Biocontrol tests against mycotoxigenic moulds showed that almost 50% of strains had an inhibitory effect on growth. Additionally, 53% of the strains grew in the presence of 100 mg/L of zinc. It has been proven that yeasts can be useful tools for biodetoxification, although further experiments must be carried out in order to ascertain the mechanisms involved.

Microbe-Mediated Extracellular and Intracellular Mineralization: Environmental, Industrial, and Biotechnological Applications

Microbe-mediated mineralization is ubiquitous in nature, involving bacteria, fungi, viruses, and algae. These mineralization processes comprise calcification, silicification, and iron mineralization. The mechanisms for mineral formation include extracellular and intracellular biomineralization. The mineral precipitating capability of microbes is often harnessed for green synthesis of metal nanoparticles, which are relatively less toxic compared with those synthesized through physical or chemical methods. Microbe-mediated mineralization has important applications ranging from pollutant removal and nonreactive carriers, to other industrial and biomedical applications. Herein, the different types of microbe-mediated biomineralization that occur in nature, their mechanisms, as well as their applications are elucidated to create a backdrop for future research.

Adhesion abilities and biosorption of Cd and Mg by microorganisms - first step for eco-friendly beneficiation of phosphate ore

Chemical reagents used in traditional mineral processing can be toxic and hazardous for the environment. Therefore, the use of biotechnological methods is becoming increasingly important. Great hopes are being placed in the use of microorganisms for bio-beneficiation of raw materials. However, assessment of adhesion abilities of bacteria onto minerals surface as well as biosorption of metals are essential steps before designing final process of each ore beneficiation. The main aim of this work was an investigation of biosorption of Cd and Mg, as well as adhesion abilities of five microorganism species with minerals included in the natural mixture of phosphate ore form Djebel Onk, Algeria. The ore, due to its unique composition, created conditions for adhesion of all five tested microbial strains onto apatite surface during incubation at pH 3. Moreover, Rhodococcus erythropolis CD 130, Pseudomonas fluorescens and Escherichia coli adhered distinctly onto apatite surface during incubation at pH 7. Incubation lasting 20 min at pH 4-6 created the most favorable conditions for biosorption of metals by B. subtilis and adhesion of cells. In case of C. albicans, biosorption of metals as well as adhesion of cells onto the mineral surface were more effective after longer time and in a wider pH range.