1
|
Stangler LA, Nicolai EN, Mivalt F, Chang SY, Kim I, Kouzani AZ, Bennet K, Berk M, Uthamaraj S, Burns TC, Worrell GA, Howe CL. Development of an integrated microperfusion-EEG electrode for unbiased multimodal sampling of brain interstitial fluid and concurrent neural activity. J Neural Eng 2023; 20:016010. [PMID: 36538815 PMCID: PMC9855636 DOI: 10.1088/1741-2552/acad29] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 08/22/2022] [Accepted: 12/20/2022] [Indexed: 12/24/2022]
Abstract
Objective. To modify off-the-shelf components to build a device for collecting electroencephalography (EEG) from macroelectrodes surrounded by large fluid access ports sampled by an integrated microperfusion system in order to establish a method for sampling brain interstitial fluid (ISF) at the site of stimulation or seizure activity with no bias for molecular size.Approach. Twenty-four 560µm diameter holes were ablated through the sheath surrounding one platinum-iridium macroelectrode of a standard Spencer depth electrode using a femtosecond UV laser. A syringe pump was converted to push-pull configuration and connected to the fluidics catheter of a commercially available microdialysis system. The fluidics were inserted into the lumen of the modified Spencer electrode with the microdialysis membrane removed, converting the system to open flow microperfusion. Electrical performance and analyte recovery were measured and parameters were systematically altered to improve performance. An optimized device was tested in the pig brain and unbiased quantitative mass spectrometry was used to characterize the perfusate collected from the peri-electrode brain in response to stimulation.Main results. Optimized parameters resulted in >70% recovery of 70 kDa dextran from a tissue analog. The optimized device was implanted in the cortex of a pig and perfusate was collected during four 60 min epochs. Following a baseline epoch, the macroelectrode surrounded by microperfusion ports was stimulated at 2 Hz (0.7 mA, 200µs pulse width). Following a post-stimulation epoch, the cortex near the electrode was stimulated with benzylpenicillin to induce epileptiform activity. Proteomic analysis of the perfusates revealed a unique inflammatory signature induced by electrical stimulation. This signature was not detected in bulk tissue ISF.Significance. A modified dual-sensing electrode that permits coincident detection of EEG and ISF at the site of epileptiform neural activity may reveal novel pathogenic mechanisms and therapeutic targets that are otherwise undetectable at the bulk tissue level.
Collapse
Affiliation(s)
- Luke A Stangler
- School of Engineering, Deakin University, Geelong, Victoria 3216, Australia,
Division of Engineering, Mayo Clinic, Rochester, MN 55905, United States of America
| | - Evan N Nicolai
- Mayo Clinic Graduate School of Biomedical Sciences, Mayo Clinic, Rochester, MN 55905, United States of America
| | - Filip Mivalt
- Department of Physiology and Biomedical Engineering, Mayo Clinic, Rochester, MN 55905, United States of America,
Department of Neurology, Mayo Clinic, Rochester, MN 55905, United States of America
| | - Su-Youne Chang
- Department of Physiology and Biomedical Engineering, Mayo Clinic, Rochester, MN 55905, United States of America,
Department of Neurologic Surgery, Mayo Clinic, Rochester, MN 55905, United States of America
| | - Inyong Kim
- Department of Neurology, Mayo Clinic, Rochester, MN 55905, United States of America
| | - Abbas Z Kouzani
- School of Engineering, Deakin University, Geelong, Victoria 3216, Australia
| | - Kevin Bennet
- Division of Engineering, Mayo Clinic, Rochester, MN 55905, United States of America
| | - Michael Berk
- School of Medicine, Deakin University, Geelong, Victoria 3216, Australia
| | - Susheil Uthamaraj
- Division of Engineering, Mayo Clinic, Rochester, MN 55905, United States of America
| | - Terry C Burns
- Department of Neurologic Surgery, Mayo Clinic, Rochester, MN 55905, United States of America
| | - Gregory A Worrell
- Department of Physiology and Biomedical Engineering, Mayo Clinic, Rochester, MN 55905, United States of America,
Department of Neurology, Mayo Clinic, Rochester, MN 55905, United States of America
| | - Charles L Howe
- Department of Neurology, Mayo Clinic, Rochester, MN 55905, United States of America,
Division of Experimental Neurology, Mayo Clinic, Rochester, MN 55905, United States of America,Author to whom any correspondence should be addressed
| |
Collapse
|
2
|
Kryszak B, Szustakiewicz K, Dzienny P, Junka A, Paleczny J, Szymczyk-Ziółkowska P, Hoppe V, Grzymajło M, Antończak A. 'Cookies on a tray': Superselective hierarchical microstructured poly(l-lactide) surface as a decoy for cells. MATERIALS SCIENCE & ENGINEERING. C, MATERIALS FOR BIOLOGICAL APPLICATIONS 2022; 133:112648. [PMID: 35034812 DOI: 10.1016/j.msec.2022.112648] [Citation(s) in RCA: 2] [Impact Index Per Article: 1.0] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Subscribe] [Scholar Register] [Received: 09/02/2021] [Revised: 12/11/2021] [Accepted: 01/04/2022] [Indexed: 12/22/2022]
Abstract
In this research we developed a micro-sized hierarchical structures on a poly(l-lactide) (PLLA) surface. The obtained structures consist of round-shaped protrusions with a diameter of ~20 μm, a height of ~3 μm, and the distance between them ~30 μm. We explored the effect of structuring PLLA to design a non-cytotoxic material with increased roughness to encourage cells to settle on the surface. The PLLA films were prepared using the casting melt extrusion technique and were modified using ultra-short pulse irradiation - a femtosecond laser operating at λ = 1030 nm. A hierarchical microstructure was obtained resembling 'cookies on a tray'. The cellular response of fibro- and osteoblasts cell lines was investigated. The conducted research has shown that the laser-modified surface is more conducive to cell adhesion and growth (compared to unmodified surface) to such an extent that allows the formation of highly-selectively patterns consisting of living cells. In contrast to eukaryotic cells, the pathogenic bacteria Staphylococcus aureus covered modified and unmodified structures in an even, non-preferential manner. In turn, adhesion pattern of eukaryotic fungus Saccharomyces boulardii resembled that of fibro- and osteoblast cells rather than that of Staphylococcus. The discovered effect can be used for fabrication of personalized and smart implants in regenerative medicine.
Collapse
Affiliation(s)
- Bartłomiej Kryszak
- Department of Polymer Engineering and Technology, Faculty of Chemistry, Wrocław University of Science and Technology (WUST), Wyb. Wyspiańskiego 27, 50-370 Wrocław, Poland.
| | - Konrad Szustakiewicz
- Department of Polymer Engineering and Technology, Faculty of Chemistry, Wrocław University of Science and Technology (WUST), Wyb. Wyspiańskiego 27, 50-370 Wrocław, Poland.
| | - Paulina Dzienny
- Laser and Fiber Electronics Group, Faculty of Electronics, Photonics and Microsystem, WUST, Poland
| | - Adam Junka
- Department of Pharmaceutical Microbiology and Parasitology, Wrocław Medical University, Borowska 211A, 50-556 Wrocław, Poland
| | - Justyna Paleczny
- Department of Pharmaceutical Microbiology and Parasitology, Wrocław Medical University, Borowska 211A, 50-556 Wrocław, Poland
| | | | - Viktoria Hoppe
- Center for Advanced Manufacturing Technologies, Faculty of Mechanical Engineering, WUST, Poland
| | - Michał Grzymajło
- Department of Polymer Engineering and Technology, Faculty of Chemistry, Wrocław University of Science and Technology (WUST), Wyb. Wyspiańskiego 27, 50-370 Wrocław, Poland
| | - Arkadiusz Antończak
- Laser and Fiber Electronics Group, Faculty of Electronics, Photonics and Microsystem, WUST, Poland
| |
Collapse
|
3
|
Nakielski P, Rinoldi C, Pruchniewski M, Pawłowska S, Gazińska M, Strojny B, Rybak D, Jezierska-Woźniak K, Urbanek O, Denis P, Sinderewicz E, Czelejewska W, Staszkiewicz-Chodor J, Grodzik M, Ziai Y, Barczewska M, Maksymowicz W, Pierini F. Laser-Assisted Fabrication of Injectable Nanofibrous Cell Carriers. SMALL (WEINHEIM AN DER BERGSTRASSE, GERMANY) 2022; 18:e2104971. [PMID: 34802179 DOI: 10.1002/smll.202104971] [Citation(s) in RCA: 16] [Impact Index Per Article: 8.0] [Reference Citation Analysis] [Abstract] [Key Words] [MESH Headings] [Track Full Text] [Subscribe] [Scholar Register] [Received: 08/25/2021] [Revised: 09/30/2021] [Indexed: 06/13/2023]
Abstract
The use of injectable biomaterials for cell delivery is a rapidly expanding field which may revolutionize the medical treatments by making them less invasive. However, creating desirable cell carriers poses significant challenges to the clinical implementation of cell-based therapeutics. At the same time, no method has been developed to produce injectable microscaffolds (MSs) from electrospun materials. Here the fabrication of injectable electrospun nanofibers is reported on, which retain their fibrous structure to mimic the extracellular matrix. The laser-assisted micro-scaffold fabrication has produced tens of thousands of MSs in a short time. An efficient attachment of cells to the surface and their proliferation is observed, creating cell-populated MSs. The cytocompatibility assays proved their biocompatibility, safety, and potential as cell carriers. Ex vivo results with the use of bone and cartilage tissues proved that NaOH hydrolyzed and chitosan functionalized MSs are compatible with living tissues and readily populated with cells. Injectability studies of MSs showed a high injectability rate, while at the same time, the force needed to eject the load is no higher than 25 N. In the future, the produced MSs may be studied more in-depth as cell carriers in minimally invasive cell therapies and 3D bioprinting applications.
Collapse
Affiliation(s)
- Paweł Nakielski
- Department of Biosystems and Soft Matter, Institute of Fundamental Technological Research, Polish Academy of Sciences, Warsaw, 02-106, Poland
| | - Chiara Rinoldi
- Department of Biosystems and Soft Matter, Institute of Fundamental Technological Research, Polish Academy of Sciences, Warsaw, 02-106, Poland
| | - Michał Pruchniewski
- Department of Biosystems and Soft Matter, Institute of Fundamental Technological Research, Polish Academy of Sciences, Warsaw, 02-106, Poland
- Department of Nanobiotechnology, Institute of Biology, Warsaw University of Life Sciences, Warsaw, 02-787, Poland
| | - Sylwia Pawłowska
- Department of Biosystems and Soft Matter, Institute of Fundamental Technological Research, Polish Academy of Sciences, Warsaw, 02-106, Poland
| | - Małgorzata Gazińska
- Department of Engineering and Technology of Polymers, Wrocław University of Science and Technology, Wrocław, 50-370, Poland
| | - Barbara Strojny
- Department of Nanobiotechnology, Institute of Biology, Warsaw University of Life Sciences, Warsaw, 02-787, Poland
| | - Daniel Rybak
- Department of Biosystems and Soft Matter, Institute of Fundamental Technological Research, Polish Academy of Sciences, Warsaw, 02-106, Poland
| | - Katarzyna Jezierska-Woźniak
- Laboratory for Regenerative Medicine, Department of Neurosurgery, School of Medicine, University of Warmia and Mazury in Olsztyn, Olsztyn, 10-082, Poland
| | - Olga Urbanek
- Laboratory of Polymers and Biomaterials, Institute of Fundamental Technological Research, Polish Academy of Sciences, Warsaw, 02-106, Poland
| | - Piotr Denis
- Laboratory of Polymers and Biomaterials, Institute of Fundamental Technological Research, Polish Academy of Sciences, Warsaw, 02-106, Poland
| | - Emilia Sinderewicz
- Laboratory for Regenerative Medicine, Department of Neurosurgery, School of Medicine, University of Warmia and Mazury in Olsztyn, Olsztyn, 10-082, Poland
| | - Wioleta Czelejewska
- Laboratory for Regenerative Medicine, Department of Neurosurgery, School of Medicine, University of Warmia and Mazury in Olsztyn, Olsztyn, 10-082, Poland
| | - Joanna Staszkiewicz-Chodor
- Laboratory for Regenerative Medicine, Department of Neurosurgery, School of Medicine, University of Warmia and Mazury in Olsztyn, Olsztyn, 10-082, Poland
| | - Marta Grodzik
- Department of Nanobiotechnology, Institute of Biology, Warsaw University of Life Sciences, Warsaw, 02-787, Poland
| | - Yasamin Ziai
- Department of Biosystems and Soft Matter, Institute of Fundamental Technological Research, Polish Academy of Sciences, Warsaw, 02-106, Poland
| | - Monika Barczewska
- Laboratory for Regenerative Medicine, Department of Neurosurgery, School of Medicine, University of Warmia and Mazury in Olsztyn, Olsztyn, 10-082, Poland
| | - Wojciech Maksymowicz
- Laboratory for Regenerative Medicine, Department of Neurosurgery, School of Medicine, University of Warmia and Mazury in Olsztyn, Olsztyn, 10-082, Poland
| | - Filippo Pierini
- Department of Biosystems and Soft Matter, Institute of Fundamental Technological Research, Polish Academy of Sciences, Warsaw, 02-106, Poland
| |
Collapse
|
4
|
Dong J, Pacella M, Liu Y, Zhao L. Surface engineering and the application of laser-based processes to stents - A review of the latest development. Bioact Mater 2021; 10:159-184. [PMID: 34901537 PMCID: PMC8636930 DOI: 10.1016/j.bioactmat.2021.08.023] [Citation(s) in RCA: 14] [Impact Index Per Article: 4.7] [Reference Citation Analysis] [Abstract] [Key Words] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 04/30/2021] [Revised: 08/04/2021] [Accepted: 08/20/2021] [Indexed: 12/21/2022] Open
Abstract
Late in-stent thrombus and restenosis still represent two major challenges in stents’ design. Surface treatment of stent is attracting attention due to the increasing importance of stenting intervention for coronary artery diseases. Several surface engineering techniques have been utilised to improve the biological response in vivo on a wide range of biomedical devices. As a tailorable, precise, and ultra-fast process, laser surface engineering offers the potential to treat stent materials and fabricate various 3D textures, including grooves, pillars, nanowires, porous and freeform structures, while also modifying surface chemistry through nitridation, oxidation and coatings. Laser-based processes can reduce the biodegradable materials' degradation rate, offering many advantages to improve stents’ performance, such as increased endothelialisation rate, prohibition of SMC proliferation, reduced platelet adhesion and controlled corrosion and degradation. Nowadays, adequate research has been conducted on laser surface texturing and surface chemistry modification. Laser texturing on commercial stents has been also investigated and a promotion of performance of laser-textured stents has been proved. In this critical review, the influence of surface texture and surface chemistry on stents performance is firstly reviewed to understand the surface characteristics of stents required to facilitate cellular response. This is followed by the explicit illustration of laser surface engineering of stents and/or related materials. Laser induced periodic surface structure (LIPSS) on stent materials is then explored, and finally the application of laser surface modification techniques on latest generation of stent devices is highlighted to provide future trends and research direction on laser surface engineering of stents. Compared conventional surface engineering with laser-based methods for biomedical devices. Explained the influence of texture geometry and surface chemistry on stents biological response. Reviewed state of the art in laser surface engineering of stents for improved biological response. Reviewed state of the art in laser surface engineering to control degradation of bioresorbable stents. Highlighted novel laser surface engineering designs for improved stents'performance.
Collapse
Affiliation(s)
- J Dong
- Wolfson School of Mechanical, Electrical and Manufacturing Engineering, Loughborough University, Loughborough, Leicestershire, LE11 3TU, UK
| | - M Pacella
- Wolfson School of Mechanical, Electrical and Manufacturing Engineering, Loughborough University, Loughborough, Leicestershire, LE11 3TU, UK
| | - Y Liu
- Wolfson School of Mechanical, Electrical and Manufacturing Engineering, Loughborough University, Loughborough, Leicestershire, LE11 3TU, UK.,Centre for Biological Engineering, Loughborough University, Loughborough, Leicestershire, LE11 3TU, UK
| | - L Zhao
- Wolfson School of Mechanical, Electrical and Manufacturing Engineering, Loughborough University, Loughborough, Leicestershire, LE11 3TU, UK
| |
Collapse
|
5
|
Detection and elimination of pulse train instabilities in broadband fibre lasers using dispersion scan. Sci Rep 2020; 10:7242. [PMID: 32350325 PMCID: PMC7190630 DOI: 10.1038/s41598-020-64109-x] [Citation(s) in RCA: 8] [Impact Index Per Article: 2.0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/05/2019] [Accepted: 03/31/2020] [Indexed: 11/25/2022] Open
Abstract
We use self-calibrating dispersion scan to experimentally detect and quantify the presence of pulse train instabilities in ultrashort laser pulse trains. We numerically test our approach against two different types of pulse instability, namely second-order phase fluctuations and random phase instability, where the introduction of an adequate metric enables univocally quantifying the amount of instability. The approach is experimentally demonstrated with a supercontinuum fibre laser, where we observe and identify pulse train instabilities due to nonlinear propagation effects under anomalous dispersion conditions in the photonic crystal fibre used for spectral broadening. By replacing the latter with an all-normal dispersion fibre, we effectively correct the pulse train instability and increase the bandwidth of the generated coherent spectrum. This is further confirmed by temporal compression and measurement of the output pulses down to 15 fs using dispersion scan.
Collapse
|
6
|
Synthesis, characterization, and crystallization behaviors of poly( D-lactic acid)-based triblock copolymer. Sci Rep 2020; 10:3627. [PMID: 32107422 PMCID: PMC7046728 DOI: 10.1038/s41598-020-60458-9] [Citation(s) in RCA: 15] [Impact Index Per Article: 3.8] [Reference Citation Analysis] [Abstract] [Track Full Text] [Download PDF] [Figures] [Journal Information] [Subscribe] [Scholar Register] [Received: 11/28/2019] [Accepted: 01/23/2020] [Indexed: 12/22/2022] Open
Abstract
Poly(D-lactic acid) (PDLA) with different polyethylene glycol (PEG) segment synthesized PDLA-PEG-PDLA triblock copolymer through the ring-opening reaction of D-LA and PEG will be used as a toughening modifier. The microstructure, crystal structures and crystallization behaviors of this triblock copolymer were investigated by Fourier transform infrared (FTIR) spectroscopy, nuclear magnetic resonance (NMR) spectroscopy, X-ray diffraction (XRD), differential scanning calorimetry (DSC) and polarized optical microscopy (POM). The triblock copolymer is synthesized from the appearance of CH2 stretching vibration peak at 2910 cm−1 and C-O stretching vibration peak at 1200 cm−1 from PEG in FTIR spectra. Moreover, the chemical shift that is about 3.6 ppm in 1H NMR and 68.8ppm in 13C NMR proves this matter. The results of XRD and DSC reveal that PDLA and PEG are crystallized separately, and are not fully compatible, and microphase separation has occurred in this triblock copolymer. PEG can induce the triblock copolymer to accelerate the rate of crystallization, allowing it to crystallize more completely in the same amount of time. When the molecular weight of PEG is 6000 or the ratio of D-LA/PEG is 1/1, the crystallizability of PDLA-PEG-PDLA triblock copolymer is the best.
Collapse
|