Design, fabrication, and optical characterization of one-dimensional photonic crystals based on porous silicon assisted by in-situ photoacoustics

Thermal transport properties of porous silicon filled by ionic liquid nanocomposite system

This paper investigates thermal transport in a nanocomposite system consisting of a porous silicon matrix filled with ionic liquid. Firstly, the thermal conductivity and heat capacity of two imidazolium and one ammonium ionic liquids were evaluated using the photoacoustic approach in piezoelectric configuration and differential scanning calorimetry, respectively. Then, the thermal transport properties of the composite system "ionic liquid confined inside porous silicon matrix" were investigated with the photoacoustic approach in gas-microphone configuration. The results demonstrated a significant enhancement of the thermal conductivity of the composite system when compared to the individual components, i.e. (i) more than two times for pristine porous silicon and (ii) more than eight times for ionic liquids. These results provide new paths for innovative solutions in the field of thermal management, particularly in the development of highly efficient energy storage devices.

Investigation on Enamel and Dentine of Tooth through 1D Photonic Structure to Identify the Caries in Human Teeth

In this research, a one-dimensional (1D) photonic structure was employed to study the nature of both enamel and dentine teeth at the signal of 1.8 THz. A simple three layer one-dimensional crystal is chosen to avoid fabrication intricacy. The materials and methods for sample preparations are discussed. The principle of investigation of caries in the teeth relies on the amount of reflected signal from the structure. Similarly, reflectance is a function of refractive indices and thickness of each layer, the nature of both substrate and infiltrated materials, and the configuration of the structure. Apart from this, the fabrication process of one-dimensional structure and experimental set-up was proposed in this article. The numerical treatment is explained here to obtain reflectance, and subsequently, the output potential. Comparison studies on output potential between enamel and dentine are also shown through graphical representation. The output result in terms of milli-Volt (mV) were obtained at the output end and collected at the photodiode. Interesting results were also observed at the photodetector. For example; the output potential of the reflected signal is around 0.18 mV for both enamel and dentine teeth whereas the potential is more than 0.26 mV and 0.31 mV for caries in dentine and enamel, respectively. Finally, it was inferred that the nature of teeth pertaining to the caries in the enamel and dentine teeth can be investigated by identifying the amount of potential at the output end.

Application of the Photoacoustic Approach in the Characterization of Nanostructured Materials

A new generation of sensors can be engineered based on the sensing of several markers to satisfy the conditions of the multimodal detection principle. From this point of view, photoacoustic-based sensing approaches are essential. The photoacoustic effect relies on the generation of light-induced deformation (pressure) perturbations in media, which is essential for sensing applications since the photoacoustic response is formed due to a contrast in the optical, thermal, and acoustical properties. It is also particularly important to mention that photoacoustic light-based approaches are flexible enough for the measurement of thermal/elastic parameters. Moreover, the photoacoustic approach can be used for imaging and visualization in material research and biomedical applications. The advantages of photoacoustic devices are their compact sizes and the possibility of on-site measurements, enabling the online monitoring of material parameters. The latter has significance for the development of various sensing applications, including biomedical ones, such as monitoring of the biodistribution of biomolecules. To extend sensing abilities and to find reliable measurement conditions, one needs to clearly understand all the phenomena taking place during energy transformation during photoacoustic signal formation. Therefore, the current paper is devoted to an overview of the main measurement principles used in the photoacoustic setup configurations, with a special focus on the key physical parameters.

In Situ Photoacoustic Study of Optical Properties of P-Type (111) Porous Silicon Thin Films

Porous silicon (PSi) on p++-type (111) silicon substrate has been fabricated by electronically etching method in hydrofluoric acid (HF) media from 5 to 110 mA/cm2 of anodizing current density. The problem of determining the optical properties of (111) PSi is board through implementing a photoacoustic (PA) technique coupled to an electrochemical cell for real-time monitoring of the formation of porous silicon thin films. PA amplitude allows the calculation of the real part of the films refractive index and porosity using the reflectance self-modulation due to the interference effect between the PSi film and the substrate that produces a periodic PA amplitude. The optical properties are studied from specular reflectance measurements fitted through genetic algorithms, transfer matrix method (TMM), and the effective medium theory, where the Maxwell Garnett (MG), Bruggeman (BR), and Looyenga (LLL) models were tested to determine the most suitable for pore geometry and compared with the in situ PA method. It was found that (111) PSi exhibit a branched pore geometry producing optical anisotropy and high scattering films.

Supported Porous Nanostructures Developed by Plasma Processing of Metal Phthalocyanines and Porphyrins

The large area scalable fabrication of supported porous metal and metal oxide nanomaterials is acknowledged as one of the greatest challenges for their eventual implementation in on-device applications. In this work, we will present a comprehensive revision and the latest results regarding the pioneering use of commercially available metal phthalocyanines and porphyrins as solid precursors for the plasma-assisted deposition of porous metal and metal oxide films and three-dimensional nanostructures (hierarchical nanowires and nanotubes). The most advanced features of this method relay on its ample general character from the point of view of the porous material composition and microstructure, mild deposition and processing temperature and energy constrictions and, finally, its straightforward compatibility with the direct deposition of the porous nanomaterials on processable substrates and device-architectures. Thus, taking advantage of the variety in the composition of commercially available metal porphyrins and phthalocyanines, we present the development of metal and metal oxides layers including Pt, CuO, Fe₂O₃, TiO₂, and ZnO with morphologies ranging from nanoparticles to nanocolumnar films. In addition, we combine this method with the fabrication by low-pressure vapor transport of single-crystalline organic nanowires for the formation of hierarchical hybrid organic@metal/metal-oxide and @metal/metal-oxide nanotubes. We carry out a thorough characterization of the films and nanowires using SEM, TEM, FIB 3D, and electron tomography. The latest two techniques are revealed as critical for the elucidation of the inner porosity of the layers.