Peculiarities of pseudogap in Y0.95Pr0.05Ba2Cu3O7-δ single crystals under pressure up to 1.7 GPa

Excess Conductivity Analysis of an YBCO Foam Strut and Its Microstructure

Struts of a superconducting YBa2Cu3Oy (YBCO) foam prepared by the infiltration growth method on the base of commercial polyurethane foams were extracted from the bulk, and thoroughly characterized concerning the microstructure and the magnetoresistance, measured by the four-point technique. Optical microscopy, electron microscopy, electron backscatter diffraction and atomic force microscopy observations indicate a unique microstructure of the foam struts which shows a large amount of tiny Y2BaCuO5 (Y-211) particles (with diameters between 50 and 100 nm) being enclosed in channel-like grain boundaries between the YBCO grains and a one-of-a-kind surface of the struts covered with Ba3Cu5Oy-particles. The resistance data obtained at temperatures in the range 4.2 K ≤T≤ 150 K (applied magnetic fields ranging from 0 to 7 T) were analyzed in the framework of the fluctuation-induced conductivity (FIC) approach using the models of Aslamazov-Larkin (AL) and Lawrence-Doniach (LD). The resulting FIC curves reveal the presence of five distinct fluctuation regimes, namely, the short-wave (SWF), one-dimensional (1D), two-dimensional (2D), three-dimensional (3D), and critical (CR) fluctuation domains. The analysis of the FIC data enable the coherence length in the direction of the c-axis at zero-temperature (ξc(0)), the irreversibility field (Birr), the upper critical magnetic field (Bc2), the critical current density at T= 0 K (Jc(0)) and several other parameters describing the the material's superconducting properties to be determined. The present data reveal that the minuscule Y-211 particles found along the YBCO grain boundaries alter the excess conductivity and the fluctuation behavior as compared to conventional YBCO samples, leading to a quite high value for Jc(0) for a sample with a non-optimized pinning landscape.

Fluctuation induced conductivity and pseudogap state studies of Bi1.6Pb0.4Sr2Ca2Cu3O10+δ superconductor added with ZnO nanoparticles

The major limitations of the Bi_1.6Pb_0.4Sr₂Ca₂Cu₃O_10+δ superconductor are weak flux pinning capability and weak inter-grains coupling that lead to a low critical current density and low critical magnetic field which impedes the suppleness of this material towards practical applications. The addition of nanoscales impurities can create artificial pining centers that may improve flux pinning capability and intergranular coupling. In this work, the influences of ZnO nanoparticles on the superconducting parameters and pseudogap properties of the Bi_1.6Pb_0.4Sr₂Ca₂Cu₃O_10+δ superconductor are investigated using fluctuation induced conductivity analyses. Results demonstrate that the ZnO nanoparticles addition improves the formation of the Bi_1.6Pb_0.4Sr₂Ca₂Cu₃O_10+δ phase significantly. Various superconducting parameters include coherence length along c-axis (ξ_c(0)), penetration depth (λ_pd(0)), Fermi velocity (v_F), Fermi energy (E_F), lower and upper critical magnetic fields (B_c1(0) and B_c2(0) respectively) and critical current density (J_c(0)), are estimated for samples with different amounts of ZnO nanoparticles. It is found that the values of the B_c1(0), B_c2(0), and J_c(0) are improved significantly in the 0.2 wt% ZnO added sample in comparison to the ZnO-free sample. The magnitude and temperature dependence of the pseudogap Δ*(T) is calculated using the local pairs model. The obtained values of T_pair, the temperature at which local pairs are transformed from strongly coupled bosons into the fluctuating Cooper pairs, increases as the added ZnO nanoparticles concentration enhances up to 0.2 wt%. Also, the estimated values for the superconducting gap at T = 0 K (Δ(0)) are decreased from about 26 meV in ZnO-free sample to about 22 meV in 0.2 wt% ZnO added sample and then increases for higher values of additive.