Cell type specific adhesion to surfaces functionalised by amine plasma polymers

Enhancing silk fibroin structures and applications through angle-dependent Ar+ plasma treatment

This study tackles limitations of Silk Fibroin (SF), including availability of sites for modification. This is achieved by Direct Plasma Nanosynthesis (DPNS), an Ar+ bombardment method, to generate and modify nanostructures and nanoscale properties on the SF surface. SF samples were treated with DPNS at incidence angles of 45o and 60o, with specific ion dose and energy parameters (1 × 1018 ions/cm2 and 500 eV, respectively) maintained throughout the process. Fourier-transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS) primarily underscored transformations in SF's nitrogenous components. Specifically, treatment produced a boost in C-NH2, particularly pronounced in the 45o-treated samples, suggesting changes were more superficial than alterations to the secondary structure. The DPNS treatment gave rise to periodic nanocone structures on the SF surface, with a scale increase correlated to a higher angle of incidence. This resulted in a decrease in surface stiffness and significant changes in the motility of J774 macrophages interacting with the transformed SF. Furthermore, the SF samples treated at a 60o incidence showcased a confinement effect, moderating the macrophages' motility, morphology, and inflammatory response. The DPNS-induced alterations not only mitigate SF's limitations but also affect cellular behavior, expanding potential for SF in biomaterials.

The Cell Adhesion and Proliferation Enhancement Impact of Low-Temperature Atmospheric Pressure Plasma-Polymerized Heptylamine on the Surface of Ti6Al4V Alloy

To chemically functionalize the Ti6Al4V alloy surface, a custom-made low-temperature atmospheric pressure plasma reactor device was used to polymerize heptylamine on it. The effect of different deposition times, an important process parameter, was also investigated. For each deposition time group, the surface morphology was observed via scanning electron microscopy (SEM). The surface chemical content was analyzed via X-ray photoelectron spectroscopy, and surface hydrophilicity was measured via water contact angle. The adhesion of bone marrow stromal cells (BMSCs) on the modified Ti6Al4V alloy surfaces was also observed via SEM. A quantitative evaluation of cell proliferation was performed via the Cell Counting Kit-8 assay. The results revealed that amino groups were introduced on the Ti6Al4V alloy surface via plasma-polymerized heptylamine (PPHA). The percentages of NH2/C for various deposition times (0 s, 30 s, 45 s, 60 s, 90 s, and 120 s) were 3.39%, 5.14%, 6.71%, 6.72%, 7.31%, and 7.65%. A 30 s, 45 s, and 60 s deposition time could significantly increase surface hydrophilicity with a mean water contact angle of 62.1 ± 1.6°, 65.7 ± 1.1°, and 88.2 ± 1.4°, respectively. Meanwhile, a 60 s, 90 s, and 120 s deposition time promoted BMSCs cell adhesion and proliferation. However, this promotion effect differed non-significantly among the three groups. In conclusion, the introduction of amino groups on the Ti6Al4V alloy surface exhibited surface modification and enhancement of cell adhesion and proliferation, which was partially associated with deposition time.

Cross-Linked Electrospun pH-Sensitive Nanofibers Adsorbed with Temporin-Ra for Promoting Wound Healing

Bioresponsive nanodrug delivery systems have excellent potential in tissue engineering applications. Poly-anionic and poly-cationic biopolymers have provided a superior platform for designing pH-sensitive drug delivery systems. In this regard, hyaluronic acid-chitosan-polyvinyl alcohol complex nanofibers with high quality and reproducibility were produced by optimizing the solution preparation process. In addition, the synthesized composite nanofiber, with 66.82 kN/mm toughness, 200% swelling ratio, and 60% porosity, exhibited excellent properties to meet the requirements of the ideal wound dressing. Green cross-linking with citric acid prevented the destruction of the nanofiber even after prolonged immersion in biological solutions. ζ potential studies demonstrated that the synthesized nanofiber has a negative surface charge (∼-30) at physiological pH. The pK_a of the temporin-Ra peptide is about 10, and as a result the peptide molecules have a net positive charge in physiological conditions. Therefore, peptide molecules immobilized on the synthesized scaffold based on surface adsorption. In vivo evaluation has proven that the wound bed has an alkaline environment, facilitating peptide release from the nanofiber scaffold. Electrospun nanofibers can imitate the architecture of the extracellular matrix for accelerating wound healing. In vitro investigation showed better adhesion, proliferation, migration, and fibroblast cell growth on peptide-loaded nanofiber samples than other groups. In vivo studies on full-thickness wounds in the mouse model indicated that the designed nanofiber was gradually absorbed without causing dryness or infection. On day 6, the peptide-loaded nanofiber revealed 60% wound closure compared to the control group (17%). In addition, based on histological studies, the composite nanofiber demonstrated excellent tissue repair ability, hence these active nanofiber mats can be a good alternative to existing wound dressings. Gene expression studies show that the antimicrobial peptide promotes the inflammatory phase of wound healing in a shorter time frame by accelerating the tumor necrosis factor-α cytokine response.

PCL/Gelatin/Graphene Oxide Electrospun Nanofibers: Effect of Surface Functionalization on In Vitro and Antibacterial Response

The emergence of resistance to pathogenic bacteria has resulted from the misuse of antibiotics used in wound treatment. Therefore, nanomaterial-based agents can be used to overcome these limitations. In this study, polycaprolactone (PCL)/gelatin/graphene oxide electrospun nanofibers (PGO) are functionalized via plasma treatment with the monomeric groups diallylamine (PGO-M1), acrylic acid (PGO-M2), and tert-butyl acrylate (PGO-M3) to enhance the action against bacteria cells. The surface functionalization influences the morphology, surface wettability, mechanical properties, and thermal stability of PGO nanofibers. PGO-M1 and PGO-M2 exhibit good antibacterial activity against Staphylococcus aureus and Escherichia coli, whereas PGO-M3 tends to reduce their antibacterial properties compared to PGO nanofibers. The highest proportion of dead bacteria cells is found on the surface of hydrophilic PGO-M1, whereas live cells are colonized on the surface of hydrophobic PGO-M3. Likewise, PGO-M1 shows a good interaction with L929, which is confirmed by the high levels of adhesion and proliferation with respect to the control. All the results confirm that surface functionalization can be strategically used as a tool to engineer PGO nanofibers with controlled antibacterial properties for the fabrication of highly versatile devices suitable for different applications (e.g., health, environmental pollution).

Surface grafting of sericin onto thermoplastic polyurethanes to improve cell adhesion and function

Thermoplastic polyurethane (TPU) membrane has super physical-mechanical properties and biocompatibility, but the surface is inert and lack of active groups which limit its application in cell culture. Silk sericin (SS) can improve cell adhesion, proliferation, growth and metabolism. In this paper, SS was grafted onto the surface of TPU membrane by -NH₂ bridge to build a high efficiency cell culture membrane. The FT-IR spectrum results indicated SS was grafted by chemical bond. According to the SEM and AFM results, we found that the grafting of SS reduced the water contact angle by 43.31% and increased the surface roughness by about four times. When TPU-SS was used for HepG2 cell culture, the cell adhesion rate of TPU-SS was significantly higher than that of the general TCPS cell culture plate, and the cell proliferation rate was close to that of TCPS. FDA/EB staining showed that HepG2 cells remained a better cellular growth behavior. HepG2 cells had higher cell vitality including the albumin secretion and the intracellular total protein synthesis. Grafting SS maintained the stability of cell and significantly decreased the cytotoxicity by decreased LDH release. In conclusion, SS grafting is beneficial to cell culture in vitro, and provides a key material for bioartificial liver culture system.

Fabrication Strategies Towards Hydrogels for Biomedical Application: Chemical and Mechanical Insights

This review aims at giving selected chemical and mechanical insights on design criteria that should be taken into account in hydrogel production for biomedical applications. Particular emphasis will be given to the chemical aspects involved in hydrogel design: macromer chemical composition, cross-linking strategies and chemistry towards "conventional" and smart/stimuli responsive hydrogels. Mechanical properties of hydrogels in view of regenerative medicine applications will also be considered.

Antimicrobial cryogel dressings towards effective wound healing

Cryogels are macroporous hydrogels that have been widely utilized in a variety of biomedical applications including wound dressings. Cryogels reveal superior mechanical and swelling properties as well as large and interconnected porosity. As traditional hydrogel wound dressings generally show undesirable mechanical and swelling characteristics, cryogels, due to their toughness and superfast swelling, offer an outstanding platform to address the growing number of various types of wounds. Moreover, recently, cryogel wound dressings loaded with an antimicrobial agent emerged as a feasible option to reduce infection, and thus improve the wound healing process. However, a comprehensive review of antimicrobial cryogels as a wound dressing is still lacking in the literature. In this review, we summarize the progress of cryogels in the area of wound dressings and provide an overview of the various polymers, namely, natural and synthetic which have been employed in cryogel wound dressing preparation. Furthermore, the most prominent antimicrobial agents incorporated in cryogel wound dressings are provided. Finally, the future directions of cryogel wound dressings for wound healing are also discussed.

Evaluation of PEEK-TiO2- SiO2 nanocomposite as biomedical implants with regard to in-vitro biocompatibility and material characterization

Polyether Ether Ketone (PEEK) exhibits superior mechanical and biological safety characteristics, and its biological inertness significantly restricts its applicability in biomedical applications. Recent researches included active ceramic particles to enhance biological activity and broaden the application range of bioactive composites in medical implants. During the current investigation, acrylic acid-functionalized ceramic TiO₂ and SiO₂ nanoparticles (NP) were used to reinforce the PEEK matrix. The PEEK/TiO₂/SiO₂ (PTS) nanocomposite was fabricated using plastic injection moulding process. Different functional groups and crystal plane orientations of the composite were found through FTIR and XRD. The morphological and elemental analysis were carried out using FESEM and the EDAX mapping technique. The thermal stability of the composite was investigated through TGA and DSC analysis. The mean diameter of the inhibition zone of PTS polymer composite is 18.125 mm and 16.375 mm against E. coli and B. subtilis, respectively, which is higher than that of the mean diameter of the inhibition zone of PEEK. In-vitro direct and indirect cytotoxicity studies were carried using the MG-63 cell line and found the cell viability as 94.30% and cytotoxicity as 5.70% on PTS nanocomposite. Cell adhesion study was carried out using MG-63 cell line on the composite surface. That demonstrated the good cell adherence and cell proliferation those were observed through SEM morphologies. Thus, the newly developed composite serves as a potential candidate in biomedical applications.

Bioconjugation Strategy for Ceramic Membranes Decorated with Candida Antarctica Lipase B-Impact of Immobilization Process on Material Features

A strategy for the bioconjugation of the enzyme Candida antarctica lipase B onto titania ceramic membranes with varied pore sizes (15, 50, 150, and 300 kDa) was successfully performed. The relationship between the membrane morphology, i.e.,the pore size of the ceramic support, and bioconjugation performance was considered. Owing to the dimension of the enzyme (~33 kDa), the morphology of the ceramics allowed (50, 150, and 300 kDa) or did not allow (15 kDa) the entrance of the enzyme molecules into the porous structure. Such a strategy made it possible to better understand the changes in the material (morphology) and physicochemical features (wettability, adhesiveness, and surface charge) of the samples, which were systematically examined. The silane functionalization and enzyme immobilization were accomplished via the covalent route. The samples were characterized after each stage of the modification, which was very informative from the material point of view. As a consequence of the modification, significant changes in the contact angle, roughness, adhesion, and zeta potential were observed. For instance, for the 50 kDa membrane, the contact angle increased from 29.1 ± 1.5° for the pristine sample to 72.3 ± 1.5° after silane attachment; subsequently, it was reduced to 57.2 ± 1.5° after the enzyme immobilization. Finally, the contact angle of the bioconjugated membrane used in the enzymatic process rose to 92.9 ± 1.5°. By roughness (S_q) controlling, the following amendments were noticed: for the pristine 50 kDa membrane, S_q = 1.87 ± 0.21 µm; after silanization, S_q = 2.33 ± 0.30 µm; after enzyme immobilization, S_q = 2.74 ± 0.26 µm; and eventually, after the enzymatic process, S_q = 2.37 ± 0.27 µm. The adhesion work of the 50 kDa samples was equal to 136.41 ± 2.20 mN m⁻¹ (pristine membrane), 94.93 ± 2.00 mN m⁻¹ (with silane), 112.24 ± 1.90 mN m⁻¹ (with silane and enzyme), and finally, 69.12 ± 1.40 mN m⁻¹ (after the enzymatic process). The materials and physicochemical features changed substantially, particularly after the application of the membrane in the enzymatic process. Moreover, the impact of ceramic material morphology on the zeta potential value is here presented for the first time. With an increase in the ceramic support cut-off, the amount of immobilized lipase rose, but the specific productivity was higher for membranes possessing smaller pores, owing to the higher grafting density. For the enzymatic process, two modes of accomplishment were selected, i.e., stirred-tank and cross-flow. The latter method was characterized by a much higher effectiveness, with a resulting productivity equal to 99.7 and 60.3 µmol h⁻¹ for the 300 and 15 kD membranes, respectively.

Application of plasma polymerized pyrrole nanoparticles to prevent or reduce de-differentiation of adult rat ventricular cardiomyocytes

Cardiovascular diseases are the leading cause of death in the world, cell therapies have been shown to recover cardiac function in animal models. Biomaterials used as scaffolds can solve some of the problems that cell therapies currently have, plasma polymerized pyrrole (PPPy) is a biomaterial that has been shown to promote cell adhesion and survival. The present research aimed to study PPPy nanoparticles (PPPyN) interaction with adult rat ventricular cardiomyocytes (ARVC), to explore whether PPPyN could be employed as a nanoscaffold and develop cardiac microtissues. PPPyN with a mean diameter of 330 nm were obtained, the infrared spectrum showed that some pyrrole rings are fragmented and that some fragments of the ring can be dehydrogenated during plasma synthesis, it also showed the presence of amino groups in the structure of PPPyN. PPPyN had a significant impact on the ARVC´s shape, delaying dedifferentiation, necrosis, and apoptosis processes, moreover, the cardiomyocytes formed cell aggregates up to 1.12 mm² with some aligned cardiomyocytes and generated fibers on its surface similar to cardiac extracellular matrix. PPPyN served as a scaffold for adult ARVC. Our results indicate that PPPyN-scaffold is a biomaterial that could have potential application in cardiac cell therapy (CCT).

Engineering 3D Cortical Spheroids for an In Vitro Ischemic Stroke Model

Three-dimensional (3D) spheroids composed of brain cells have shown great potential to mimic the pathophysiology of the brain. However, a 3D spheroidal brain-disease model for cerebral ischemia has not been reported. This study investigated an ultralow attachment (ULA) surface-mediated formation of 3D cortical spheroids using primary rat cortical cells to recapitulate the cerebral ischemic responses in stroke by oxygen-glucose deprivation-reoxygenation (OGD-R) treatment. Comparison between two-dimensional (2D) and 3D cell culture models confirmed the better performance of the 3D cortical spheroids as normal brain models. The cortical cells cultured in 3D maintained their healthy physiological morphology of a less activated state and suppressed mRNA expressions of pathological stroke markers, S100B, IL-1β, and MBP, selected based on in vivo stroke model. Interestingly, the spheroids formed on the ULA surface exhibited striking aggregation dynamics involving active cell-substrate interactions, whereas those formed on the agarose surface aggregated passively by the convective flow of the media. Accordingly, ULA spheroids manifested a layered arrangement of neurons and astrocytes with higher expressions of integrin β1, integrin α5, N-cadherin, and fibronectin than the agarose spheroids. OGD-R-induced stroke model of the ULA spheroids successfully mimicked the ischemic response as evidenced by the upregulated mRNA expressions of the key markers for stroke, S100B, IL-1β, and MBP. Our study suggested that structurally and functionally distinct cortical spheroids could be generated by simply tuning the cell-substrate binding activities during dynamic spheroidal formation, which should be an essential factor to consider in establishing a brain-disease model.

Bioactive and biopassive treatment of poly(ethylene terephthalate) multifilament textile yarns to improve/prevent fibroblast viability

To modulate the physicochemical features of poly(ethylene terephthalate) (PET) multifilaments surface composing a complex textile structure (core and shell system), intended to improve upon current implants for high extension injuries of the Achilles tendon or even for its total replacement, two surface treatments with different purposes (bioactive and biopassive) were studied. The first treatment is based on amino groups grafting using ethylenediamine molecules to be applied in the structure core to improve cell adhesion and proliferation. The other treatment relates to a polytetrafluoroethylene (PTFE) coating to be applied in the structure shell to decrease its coefficient of friction and avoid adhesions. Both treatments were optimized to reach their purposed goals without harming the tensile properties of PET yarns, which were evaluated by static tensile tests. The resazurin assay and scanning electron microscopy analysis showed that the purposed goals related to fibroblast adhesion were achieved for both treatments and in the case of PTFE coating, the abrasion resistance was also improved according to the yarn-on-yarn abrasion tests.

Bone Marrow Mesenchymal Stromal Cells on Silk Fibroin Scaffolds to Attenuate Polymicrobial Sepsis Induced by Cecal Ligation and Puncture

Suitable scaffolds with appropriate mechanical and biological properties can improve mesenchymal stromal cell (MSC) therapy. Because silk fibroins (SFs) are biocompatible materials, they were electrospun and applied as scaffolds for MSC therapy. Consequently, interferon (IFN)-primed human bone marrow MSCs on SF nanofibers were administered into a polymicrobial sepsis murine model. The IL-6 level gradually decreased from 40 ng/mL at 6 h after sepsis to 35 ng/mL at 24 h after sepsis. The IL-6 level was significantly low as 5 ng/mL in primed MSCs on SF nanofibers, and 15 ng/mL in primed MSCs on the control surface. In contrast to the acute response, inflammation-related factors, including HO-1 and COX-2 in chronic liver tissue, were effectively inhibited by MSCs on both SF nanofibers and the control surface at the 5-day mark after sepsis. An in vitro study indicated that the anti-inflammatory function of MSCs on SF nanofibers was mediated through enhanced COX-2-PGE₂ production, as indomethacin completely abrogated PGE₂ production and decreased the survival rate of septic mice. Thus, SF nanofiber scaffolds potentiated the anti-inflammatory and immunomodulatory functions of MSCs, and were beneficial as a culture platform for the cell therapy of inflammatory disorders.

Biomaterial-directed cell behavior for tissue engineering

Successful tissue regeneration strategies focus on the use of novel biomaterials, structures, and a variety of cues to control cell behavior and promote regeneration. Studies discovered how biomaterial/ structure cues in the form of biomaterial chemistry, material stiffness, surface topography, pore, and degradation properties play an important role in controlling cellular events in the contest of in vitro and in vivo tissue regeneration. Advanced biomaterials structures and strategies are developed to focus on the delivery of bioactive factors, such as proteins, peptides, and even small molecules to influence cell behavior and regeneration. The present article is an effort to summarize important findings and further discuss biomaterial strategies to influence and control cell behavior directly via physical and chemical cues. This article also touches on various modern methods in biomaterials processing to include bioactive factors as signaling cues to program cell behavior for tissue engineering and regenerative medicine.

Behaviour of Vascular Smooth Muscle Cells on Amine Plasma-Coated Materials with Various Chemical Structures and Morphologies

Amine-coated biodegradable materials based on synthetic polymers have a great potential for tissue remodeling and regeneration because of their excellent processability and bioactivity. In the present study, we have investigated the influence of various chemical compositions of amine plasma polymer (PP) coatings and the influence of the substrate morphology, represented by polystyrene culture dishes and polycaprolactone nanofibers (PCL NFs), on the behavior of vascular smooth muscle cells (VSMCs). Although all amine-PP coatings improved the initial adhesion of VSMCs, 7-day long cultivation revealed a clear preference for the coating containing about 15 at.% of nitrogen (CPA-33). The CPA-33 coating demonstrated the ideal combination of good water stability, a sufficient amine group content, and favorable surface wettability and morphology. The nanostructured morphology of amine-PP-coated PCL NFs successfully slowed the proliferation rate of VSMCs, which is essential in preventing restenosis of vascular replacements in vivo. At the same time, CPA-33-coated PCL NFs supported the continuous proliferation of VSMCs during 7-day long cultivation, with no significant increase in cytokine secretion by RAW 264.7 macrophages. The CPA-33 coating deposited on biodegradable PCL NFs therefore seems to be a promising material for manufacturing small-diameter vascular grafts, which are still lacking on the current market.

Biointerface Materials for Cellular Adhesion: Recent Progress and Future Prospects

While many natural instances of adhesion between cells and biological macromolecules have been elucidated, understanding how to mimic these adhesion events remains to be a challenge. Discovering new biointerface materials that can provide an appropriate environment, and in some cases, also providing function similar to the body’s own extracellular matrix, would be highly beneficial to multiple existing applications in biomedical and biological engineering, and provide the necessary insight for the advancement of new technology. Such examples of current applications that would benefit include biosensors, high-throughput screening and tissue engineering. From a mechanical perspective, these biointerfaces would function as bioactuators that apply focal adhesion points onto cells, allowing them to move and migrate along a surface, making biointerfaces a very relevant application in the field of actuators. While it is evident that great strides in progress have been made in the area of synthetic biointerfaces, we must also acknowledge their current limitations as described in the literature, leading to an inability to completely function and dynamically respond like natural biointerfaces. In this review, we discuss the methods, materials and, possible applications of biointerface materials used in the current literature, and the trends for future research in this area.