Characterization of ultrafine particles emitted during laser-based additive manufacturing of metal parts

Review of Visual Measurement Methods for Metal Vaporization Processes in Laser Powder Bed Fusion

Laser powder bed fusion (LPBF) is of great importance for the visual measurement and analysis of the metallization process, which is the process of solid, liquid, and gas phase transformations of metal powders under high-energy laser irradiation due to the low boiling point/high saturated vapor pressure. Since the evaporation of metals involves the interaction of driving forces such as vapor back pressure, surface tension, and gravity, the movement of the melt pool is not stable. At the same time, it also produces vaporization products such as vapor plumes and sprays, which cause defects such as bubbles, porosity, lack of fusion, inclusions, etc., during the manufacturing process of the parts, affecting the performance and manufacturing quality of the parts. More and more researchers are using imaging technologies, such as high-speed X-ray, high-speed visible light cameras, and high-speed schlieren imaging, to perform noncontact visual measurements and analyses of the melt pool, vapor plume, and spatter during the metal evaporation process, and the results show that the metal evaporation process can be suppressed by optimizing the process parameters and changing the processing atmosphere, thereby reducing part defects and improving part performance and built part quality. This paper reviews the research on metal evaporation mechanisms and visual measurement methods of metal evaporation, then discusses the measures of metal evaporation, and finally summarizes and prospects the future research hotspots of LPBF technology, according to the existing scholars' research on numerical simulation analysis and visual measurement methods of the metal evaporation process.

Emissions and Exposures Associated with the Use of an Inconel Powder during Directed Energy Deposition Additive Manufacturing

Additive manufacturing (AM) has been linked to potential exposure-related health risks, however, there is a paucity of sufficient research. This study aimed to supply information regarding emissions and exposure during directed energy deposition (DED) AM using inconel 718, with the main constituents being nickel, chromium, and cobalt. By using standardized occupational hygiene methods, the measurement strategy consisted of a combined approach, including powder characterization, particle emission monitoring, and personal exposure monitoring of AM operators. Powder characterization of virgin and used powder indicated no significant difference in particle size, shape, or elemental composition. Particle number emissions ranged between 102 and 105 p/cm3 for submicron particles (<1 µm in size). There was no significant difference in the particle emission rate between the three phases of AM or the two types of DED machines (p > 0.05). The particle emission rate for submicron particles peaked at 2.8 × 109 p/min. Metals of concern to human health were detected during the AM process but were considerably lower than the relevant exposure limits. This study confirms particle emissions, predominantly in the submicron range, above the background concentration during DED AM and, although insignificant in terms of potential health effects, AM operators are exposed to detectable concentrations of the metal constituents of inconel.

Is Additive Manufacturing an Environmentally and Economically Preferred Alternative for Mass Production?

The manufacturing sector accounts for a large percentage of global energy use and greenhouse gas emissions, and there is growing interest in the potential of additive manufacturing (AM) to reduce the sector's environmental impacts. Across multiple industries, AM has been used to reduce material use in final parts by 35-80%, and recent publications have predicted that AM will enable the fabrication of customized products locally and on-demand, reducing shipping and material waste. In many contexts, however, AM is not a viable alternative to traditional manufacturing methods due to its high production costs. And in high-volume mass production, AM can lead to increased energy use and material waste, worsening environmental impacts compared to traditional production methods. Whether AM is an environmentally and economically preferred alternative to traditional manufacturing depends on several hidden aspects of AM that are not readily apparent when comparing final products, including energy-intensive and expensive material feedstocks, excessive material waste during production, high machine costs, and slow rates of production. We systematically review comparative studies of the environmental impacts and costs of AM in contrast with traditional manufacturing methods and identify the conditions under which AM is the environmentally and economically preferred alternative. We find that AM has lower production costs and environmental impacts when production volumes are relatively low (below ∼1,000 per year for environmental impacts and below 42-87,000 per year for costs, depending on the AM process and part geometry) or the parts are small and would have high material waste if traditionally manufactured. In cases when the geometric freedom of AM enables performance improvements that reduce environmental impacts and costs during a product's use phase, these can counteract the higher production impacts of AM, making it the preferred alternative at larger production volumes. AM's ability to be environmentally and economically beneficial for mass manufacturing in a wider variety of contexts is dependent on reducing the cost and energy intensity of material feedstock production, eliminating the need for support structures, raising production speeds, and reducing per unit machine costs. These challenges are not primarily caused by economies of scale, and therefore, they are not likely to be addressed by the increasing expansion of the AM sector. Instead, they will require fundamental advances in material science, AM production technologies, and computer-aided design software.

Comprehensive Analysis of Two H13-Type Starting Materials Used for Laser Cladding and Aerosol Particles Formed in This Process

Laser cladding with H13 steel powders was performed and the related material transformations were studied for the particles emitted during this process. Fractions of various sizes of the aerosol particles formed during the laser cladding were collected on a cascade impactor, while the electromobility and the aerodynamic size of the particles were measured using a scanning mobility particle spectrometer and an aerodynamic particle sizer, respectively. The aerosol particles deposited onto the impactor plates were analyzed using scanning electron microscopy−energy-dispersive X-ray spectroscopy, as well as total-reflection X-ray fluorescence and X-ray absorption near-edge structure spectroscopy. Both the concentration and mean oxidation state of the major components were correlated with the aerosol particle size. The ultrafine aerosol particles (with a diameter less than about 100 nm) were predominantly oxidized and formed as the result of an evaporation−oxidation−condensation process sequence. The larger particles (>200 nm in geometric diameter) were primarily the residues of the original metal powder and exhibited a composition change as compared to the as-received metal powder. Correlations between the changes in the concentration ratio of the components were detected and explained.

Characterisation of Particles Emitted during Laser Cutting of Various Metal Sheets and an Exposure Assessment for the Laser Operators

Laser cutting is used in many industrial settings to achieve precise cuts of metal sheets. Laser operators may be exposed to particles formed during cutting when opening the cabinet or when metal sheets are exchanged. To characterise the potential exposure, particles formed during laser cutting were studied with scanning electron microscopy equipped with an energy dispersive X-ray detector and an energy backscatter diffraction detector. The total concentration of particles (11-615 nm) was determined online with a scanning mobility particle sizer. The chemical composition of the particles formed during the cutting of the different metal sheets was determined by inductively coupled plasma mass spectrometry (ICP-MS). X-ray diffraction was applied to determine the phase composition. The occupational exposure was assessed gravimetrically and by ICP-MS for five laser operators handling different laser cutters, and materials and were found to be low. Agglomerates and aggregates of condensation particles were formed during laser cutting, independent of the sheet type. Iron, present as both magnetite and α-Fe, was the main element found in the particles formed when cutting steel sheets. The size of the particles generated was mainly below 300 nm. Open laser cutters may lead to higher metal exposures, which is especially relevant when cutting metal sheets containing heavy metals.