Electromagnetic surgical navigation in patients undergoing mandibular surgery

An improved camera model for oblique-viewing laparoscopes: high reprojection accuracy independent of telescope rotation

Objective. Oblique-viewing laparoscopes are popular in laparoscopic surgeries where the target anatomy is located in narrow areas. Their viewing direction can be shifted by telescope rotation without changing the laparoscope pose. This rotation also changes laparoscope camera parameters that are estimated by camera calibration to be able to reproject an anatomical model onto the laparoscopic view, creating augmented reality (AR). The aim of this study was to develop a camera model that accounts for these changes, achieving high reprojection accuracy for any telescope rotation.Approach. Camera parameters were acquired by calibrations encompassing a wide telescope rotation range. For those parameters showing periodic changes upon rotation, interpolation models were created and used to establish an updatable camera model. With this model, corner points of a tracked checkerboard were reprojected onto the checkerboard laparoscopic images, at random rotation angles. Root-mean-square reprojection errors (RMSEs) were calculated between the reprojected and imaged corner points.Main results. Reprojection RMSEs were low and approximately independent on telescope rotation angle, over a wide rotation range of 320°. The mean reprojection RMSE was 2.8±0.7 pixels for a conventional laparoscope and 3.6±0.7 pixels for a chip-on-the-tip (COTT) laparoscope, corresponding to 0.3±0.1 mm and 0.4±0.1 mm in world coordinates respectively. Worst-case reprojection errors were about 9 pixels (0.8 mm) for both laparoscopes.Significance. The camera model developed in this study improves on existing models for oblique-viewing laparoscopes because it provides high reprojection accuracy independent of the telescope rotation angle and is applicable for conventional and chip-on-a-tip oblique-viewing laparoscopes. The work presented here is an important step towards creating accurate AR in image-guided interventions where oblique-viewing laparoscopes are used while simultaneously providing the surgeon the flexibility to rotate the telescope to any desired rotation angle.Acronyms. CC: camera coordinates; CCToolbox: camera calibration toolbox; COTT: chip-on-the-tip; CS: camera sensor; DD: decentering distortion; FL: focal length; OTS: optical tracking system; PP: principal point; RD: radial distortion; SI: supplementary information;tHE:hand-eye translation component.

Preliminary study of the accuracy and safety of robot-assisted mandibular distraction osteogenesis with electromagnetic navigation in hemifacial microsomia using rabbit models

This study aimed to investigate the accuracy and safety of mandibular osteotomy and distraction device positioning in distraction osteogenesis assisted by an electromagnetic navigation surgical robot. Twelve New Zealand white rabbits were randomly divided into two groups after computed tomography. The control group underwent a procedure based on the preoperative three-dimensional design and clinical experience. Animals in experimental group underwent a procedure with robotic assistance after registration. The accuracies of osteotomy and distraction device positioning were analysed based on distance and angular errors. The change in ramus length after a 1 cm-extension of the distraction device was for assessing distraction effect. The preparation, operative and osteotomy times, intraoperative bleeding, and teeth injury were used for safety assessment. In the experimental group, the distance (t = 2.591, p = 0.011) and angular (t = 4.276, p = 0.002) errors of osteotomy plane, and the errors in distraction device position (t = 3.222, p = 0.009) and direction (t = 4.697, p = 0.001) were lower; the distraction effect was better (t = 4.096, p = 0.002). There was no significant difference in the osteotomy time and bleeding; however, the overall operative and preparation times were increased in the experimental group, with a reduced rate of teeth damage. Robot-assisted mandibular distraction osteogenesis with electromagnetic navigation in craniofacial microsomia is feasible, safe, significantly improves surgical precision.

Dynamic 3D images fusion of the temporomandibular joints: A novel technique

OBJECTIVES

To demonstrate a procedure for fusing images from cone-beam computed tomography (CBCT), magnetic resonance imaging (MRI) and optical positioning tracking system to dynamically evaluate the relative motion of the temporomandibular joint (TMJ) for the diagnosis of temporomandibular disorders (TMD).

METHODS

CBCT data was collected from a patient wearing a fixation device with markers in the intercuspal position. The patient's mandibular movements were recorded using an optical positioning tracking system. The CBCT data were imported into a virtual simulation system to reproduce the mandibular movement. Five jaw positions were selected for 3D printing of the occlusal plate that the patient wore to undergo MRI. MRI scans were registered with the CBCT image for fusion and reconstruction.

RESULTS

The anatomical structures of the articular fossa, articular disc, and condyle were clearly displayed in the CBCT-MRI fused images. The spatial posture and relative position of the fossa-disc-condyle during mandibular movement could be reproduced dynamically using the 3D reconstruction model.

CONCLUSIONS

This method can visually display mandibular motion trajectories and the relative TMJ positions. Virtual reproduction provides a comprehensive understanding of the articular disc's morphology and position in different states from a 3D perspective.

CLINICAL SIGNIFICANCE

This method can be used in clinical studies of TMJ as an adjunct to the 3D dynamic diagnosis and assessment for complex patients with TMD and provide relevant data for doctors.

A hybrid registration method using the mandibular bone surface for electromagnetic navigation in mandibular surgery

PURPOSE

To utilize navigated mandibular (reconstructive) surgery, accurate registration of the preoperative CT scan with the actual patient in the operating room (OR) is required. In this phantom study, the feasibility of a noninvasive hybrid registration method is assessed. This method consists of a point registration with anatomic landmarks for initialization and a surface registration using the bare mandibular bone surface for optimization.

METHODS

Three mandible phantoms with reference notches on two osteotomy planes were 3D printed. An electromagnetic tracking system in combination with 3D Slicer software was used for navigation. Different configurations, i.e., different surface point areas and number and configuration of surface points, were tested with a dentate phantom (A) in a metal-free environment. To simulate the intraoperative environment and different anatomies, the registration procedure was also performed with an OR bed using the dentate phantom and two (partially) edentulous phantoms with atypical anatomy (B and C). The accuracy of the registration was calculated using the notches on the osteotomy planes and was expressed as the target registration error (TRE). TRE values of less than 2.0 mm were considered as clinically acceptable.

RESULTS

In all experiments, the mean TRE was less than 2.0 mm. No differences were found using different surface point areas or number or configurations of surface points. Registration accuracy in the simulated intraoperative setting was-mean (SD)-0.96 (0.22), 0.93 (0.26), and 1.50 (0.28) mm for phantom A, phantom B, and phantom C.

CONCLUSION

Hybrid registration is a noninvasive method that requires only a small area of the bare mandibular bone surface to obtain high accuracy in phantom setting. Future studies should test this method in clinical setting during actual surgery.