Lerf-Klinowski-type models of graphene oxide and reduced graphene oxide are robust in analyzing non-covalent functionalization with porphyrins

Agarose fibers with glycerol and graphene oxide and functional properties for potential application in biomaterials

Agarose has numerous applications in biochemistry and medical textiles. This study aimed to produce agarose-graphene oxide-glycerol fibers and analyze their properties. The agarose gel was prepared by dissolving the polymer in 9:1 (v/v) dimethyl sulfoxide (DMSO): H2O, followed by spinning in an ethanol bath (1:1 (v/v) ethanol: H2O) at 20 °C. Fibers were obtained using 8 % (m/v) agarose, 2 % (m/v) glycerol, and 0.5 % and 1 % (m/v) graphene oxide (GO). The fibers had a titer of 18.32-32.49 tex and, a tenacity of 1.40-3.35 cN/tex. GO increased the thermal resistance by 79 %. The presence of glycerol and GO was confirmed and analyzed by FTIR and XPS. Fiber water absorption was decreased by 30 % with the GO addition. The weight loss increased by 55 % after glycerol addition, 51 % with GO addition, and 36 % with glycerol and GO simultaneous addition. Furthermore, GO exhibited 100 % inhibition for both S. aureus (gram-positive) and E. coli bacteria (gram-negative). Fiber F1, with only agarose, inhibited S. aureus by 34.93 %, F2 with 2 % glycerol by 48.72 %, F3 with 0.5 % GO by 63.42 %, and F4 with 2 % glycerol and 0.5 % GO by 30.65 %. However, the inhibition increased to 49.43 % with 1 % GO. The agarose fibers showed low inhibition for E. coli, ranging from 3.35 to 12.12 %.

Multi-stage adsorption of methyl orange on the nitrogen-rich biomass-derived carbon adsorbent: DFT and MD evaluation

Dyes that are released into the environment may have negative effects on living organisms. To address this issue, a biomass-derived carbon adsorbent made from Enteromorpha was tested for its ability to remove methyl orange (MO) from wastewater. The adsorbent was found to be effective in removing MO, with a 1:4 impregnation ratio producing an adsorbent that could remove 96.34% of MO from a 200 mg/L solution using only 0.1 g of adsorbent. At higher concentrations, the adsorption capacity increased up to 269.58 mg/g. Through molecular dynamics simulations, it was discovered that after mono-layer adsorption reached saturation, the remaining MO molecules in solution formed hydrogen bonds with the adsorbed MO, which led to further aggregation on the adsorbent surface and increased adsorption capacity. Additionally, theoretical investigations revealed that the adsorption energy of anionic dyes increased with Nitrogen-doped carbon materials, with the pyrrolic-N site having the highest adsorption energy for MO. The carbon material derived from Enteromorpha showed promise in treating wastewater containing anionic dyes, thanks to its high adsorption capacity and strong electrostatic interaction with the sulfonic acid groups of MO.

Elucidating the alkene hydrogenation reaction based on cotton textile reduced graphene oxide under the influence of external electric field: Illustration of new noble method

The hydrogenation reaction of alkene is one of the most used industrial chemical process for various materials of daily life and energy consumption. This is a heterogeneous reaction and traditionally carried out by metallic catalysis. However, these conventional catalytic hydrogenations of alkene suffer from various setbacks such as catalyst poisoning, less recyclability and are environmentally unfriendly. Therefore, in recent years, researchers have been trying to develop the alternatives to metal catalysis hydrogenation of alkene. Heterogeneous catalysis under the external electric field is considered the future of green catalysis. In this paper, we report a comprehensive investigation dealing with the theoretical basis for simulating the phenomenon of heterogeneous catalysis, on a molecular level, under an external electric field. The illustration of the prospect as well as the effects of the mostly used catalytic systems, reduced graphene oxide, under the influence of external electric fields is provided. Moreover, a noble method of alkene hydrogenation reaction based on cotton textile reduced graphene oxide (CT-RGO) under the influence of an external electric field is introduced. The corresponding theoretical investigation was carried out within the framework of the density functional theory (DFT) method using first-principles calculations. The study has been carried out by elucidating DFT calculations for three different proposed catalytic systems, namely without electricity, with electricity and with an external electric field of 2 milli-Atomic unit. The obtained results indicate that adsorption energy of H₂ on the CT-RGO surface is significantly higher when the electric field is applied along the bond axis, suggesting thereby that hydrogenation of alkene can be induced with CT-RGO catalyst support under external electric fields. The obtained results shed light on the effect of the external electricity field on the graphene-hydrogen complex, the activation energy of graphene radicals to achieve the transition states as well as the adsorption of the hydrogen atoms over the graphene surface. Altogether, the theoretical results presented herein suggested that the proposed catalytic system holds promise for facilitating the alkene hydrogenation under external electric fields.

Enhancement of H2S sensing performance of rGO decorated CuO thin films: experimental and DFT studies

We demonstrate a highly selective and sensitive Cupric oxide (CuO) thin film-based low concentration Hydrogen sulfide (H₂S) sensor. The sensitivity was improved around three times by decorating with reduced graphene oxide (rGO) nanosheets. CuO thin films were deposited by Chemical Vapor Deposition followed by inter-digital electrode fabrication by a thermal evaporations system. The crystal structure of CuO was confirmed by x-ray diffraction. The sensing response of pristine CuO was found around 54% at 100 °C to 100 ppm of H₂S. In contrast, the sensing response was enhanced to 167% by decorating with rGO of 1.5 mg ml^-1concentration solution. The sensing was improved due to the formation of heterojunctions between the rGO and CuO. The developed sensor was examined under various gas environments and found to be highly selective towards H₂S gas. The improvement in sensing response has been attributed to increased hole concentration in CuO in the presence of rGO due to the Fermi level alignment and increased absorption of H₂S molecules at the rGO/CuO heterojunction. Further, electronic structure calculations show the physisorption behavior of H₂S molecules on the different adsorption sites. Detailed insight into the gas sensing mechanism is discussed based on experimental results and electronic structure calculations.

Understanding structure-properties relationships of porphyrin linked to graphene oxide through π-π-stacking or covalent amide bonds

Two graphene oxide nanoassemblies using 5-(4-(aminophenyl)-10,15,20-triphenylporphyrin (TPPNH₂) were fabricated by two synthetic methods: covalent (GO-CONHTPP) and noncovalent bonding. GO-CONHTPP was achieved through amide formation at the periphery of GO sheets and the hybrid material was fully characterized by FTIR, XPS, Raman spectroscopy, and SEM. Spectroscopic measurements together with theoretical calculations demonstrated that assembling TPPNH₂ on the GO surface in DMF-H₂O (1:2, v/v) via non-covalent interactions causes changes in the absorption spectra of porphyrin, as well as efficient quenching of its emission. Interestingly, covalent binding to GO does not affect notably neither the porphyrin absorption nor its fluorescence. Theoretical calculations indicates that close proximity and π-π-stacking of the porphyrin molecule with the GO sheet is possible only for the non-covalent functionalization. Femtosecond pump-probe experiments revealed that only the non-covalent assembly of TPPNH₂ and GO enhances the efficiency of the photoinduced electron transfer from porphyrin to GO. In contrast to the non-covalent hybrid, the covalent GO-CONHTPP material can generate singlet oxygen with quantum yields efficiency (ΦΔ = 0.20) comparable to that of free TPPNH₂ (ΦΔ = 0.26), indicating the possible use of covalent hybrid materials in photodynamic/photothermal therapy. The spectroscopic studies combined with detailed quantum-chemical analysis provide invaluable information that can guide the fabrication of hybrid materials with desired properties for specific applications.

Supercapacitance in graphene oxide materials modified with tetrapyrrole dyes: a mechanistic study

The global increase in mobile technology usage has created a need for better energy storage systems. With standard batteries reaching their technological limits, alternate energy storage methods are gaining momentum. In this study, we demonstrate a cheap and efficient way of building from scratch high-performance supercapacitors based on graphene oxide (GO) functionalized with tetrapyrrole derivatives: porphyrins and phthalocyanines. We present supercapacitors with capacitances about 30 times larger than those of the pristine graphene oxide-based counterparts. Experimental characterisation methods including X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), ultraviolet-visible spectroscopy (UV-VIS), electron paramagnetic resonance (EPR), and density functional theory (DFT) calculations revealed correlations between the structural, magnetic, electronic and thermodynamic properties of these materials and their performance as supercapacitors. Electrochemical studies indicate the complex and versatile nature of capacitive effects associated with thin layers of supramolecular composites of graphene oxide. The electrical double layer (EDL) capacitance, cation intercalation and faradaic processes are coupled. Moreover, differences in the electronic interactions between GO and tetrapyrrolic modifiers have a profound effect on the observed capacitance. At the same time, these interactions are sufficiently weak to induce only subtle spectral changes, as well as a small increase of the interlayer distance as determined by XRD measurements. The present work offers a viable strategy for manufacturing high-performance supercapacitive materials that are superior to the state of the art nanocarbon-based supercapacitors using benign electrolytes in terms of capacitance per mass unit and have the potential for application in future green energy storage technologies. Our study provides insight into the multifarious origins of supercapacitance beyond the well-known EDL mechanism.

A Comparative Investigation of Chemically Reduced Graphene Oxide Thin Films Deposited via Spray Pyrolysis

We present a comparative investigation between thin films of graphene oxide (GO) and chemically reduced graphene oxide (rGO) deposited onto glass substrates via spray pyrolysis. Two reduction techniques are investigated: (1) the exposition of a sprayed layer of GO to vapors of hydrazine hydrate to produce rGO_V and (2) the addition of liquid hydrazine hydrate to a suspended GO solution, which is then sprayed onto a substrate to produce rGO_L. Three different spectroscopy techniques, Raman, Fourier transform infrared, and UV-Vis-NIR, show that the two reduced samples have less lattice disorder in comparison to GO, with rGO_L having the highest degree of reduction. Interestingly, topography characterization by atomic force microscopy reveals a morphological change occurring during the exposure to hydrazine hydrate vapors, resulting in a thickness of 110 nm for the rGO_V film, which is a factor of 16 larger than rGO_L and GO. Finally, I-V measurements show a significant decrease of the GO's resistivity after the reduction process, where rGO_L features a resistivity 90 times lower than rGO_V, confirming that rGO_L has the highest degree of reduction. Our results indicate that the reduction process for rGO_V is susceptible to introducing intercalated water molecules in the material while the fabrication technique for rGO_L is a suitable route to obtain a material with minimal lattice disorder and properties approaching those of graphene.

Photocatalytic Degradation of Fluoroquinolone Antibiotics in Solution by Au@ZnO-rGO-gC3N4 Composites

The photocatalytic degradation of two quinolone-type antibiotics (ciprofloxacin and levofloxacin) in aqueous solution was studied, using catalysts based on ZnO nanoparticles, which were synthesized by a thermal procedure. The efficiency of ZnO was subsequently optimized by incorporating different co-catalysts of gC3N4, reduced graphene oxide, and nanoparticles of gold. The catalysts were fully characterized by electron microscopy (TEM and SEM), XPS, XRD, Raman, and BET surface area. The most efficient catalyst was 10%Au@ZnONPs-3%rGO-3%gC3N4, obtaining degradations of both pollutants above 96%. This catalyst has the largest specific area, and its activity was related to a synergistic effect, involving factors such as the surface of the material and the ability to absorb radiation in the visible region, mainly produced by the incorporation of rGO and gC3N4 in the semiconductor. The use of different scavengers during the catalytic process, was used to establish the possible photodegradation mechanism of both antibiotics.

Graphene quantum dots-porphyrins/phthalocyanines multifunctional hybrid systems: from interfacial dialogue to applications

Engineered well-ordered hybrid nanomaterials are at a symbolically pivotal point, just ahead of a long-anticipated human race transformation. Incorporating newer carbon nanomaterials like graphene quantum dots (GQDs) with tetrapyrrolic porphyrins...