Novel reusable hydrogel adsorbents for precious metal recycle

Recovery of Ag(I) from Wastewater by Adsorption: Status and Challenges

Untreated or inadequately treated silver-containing wastewater may pose adverse effects on hu-man health and the ecological environment. Currently, significant progress has been made in the treatment of Ag(I) in wastewater using adsorption methods, with adsorbents playing a pivotal role in this process. This paper provides a systematic review of various adsorbents for the recovery and treatment of Ag(I) in wastewater, including MOFs, COFs, transition metal sulfides, metal oxides, biomass materials, and other polymeric materials. The adsorption mechanisms of these materials for Ag(I) are elaborated upon, along with the challenges currently faced. Furthermore, insights into optimizing adsorbents and developing novel adsorbents are proposed in this study.

Valorization of Glucose-Derived Humin as a Low-Cost, Green, Reusable Adsorbent for Dye Removal, and Modeling the Process

Glucose can be isomerized into fructose and dehydrated into key platform biochemicals, following the "bio-refinery concept". However, this process generates black and intractable substances called humin, which possess a polymeric furanic-type structure. In this study, glucose-derived humin (GDH) was obtained by reacting D-glucose with an allylamine catalyst in a deep eutectic solvent medium, followed by a carbonization step. GDH was used as a low-cost, green, and reusable adsorbent for removing cationic methylene blue (MB) dye from water. The morphology of carbonized GDH differs from pristine GDH. The removal efficiencies of MB dye using pristine GDH and carbonized GDH were 52% and 97%, respectively. Temperature measurements indicated an exothermic process following pseudo-first-order kinetics, with adsorption behavior described by the Langmuir isotherm. The optimum parameters were predicted using the response surface methodology and found to be a reaction time of 600 min, an initial dye concentration of 50 ppm, and a GDH weight of 0.11 g with 98.7% desirability. The MB dye removal rate optimized through this model was 96.85%, which was in good agreement with the experimentally obtained value (92.49%). After 10 cycles, the MB removal rate remained above 80%, showcasing the potential for GDH reuse and cost-effective wastewater treatment.

Methacrylate-Based Polymeric Sorbents for Recovery of Metals from Aqueous Solutions

The industrialization and urbanization expansion have increased the demand for precious and rare earth elements (REEs). In addition, environmental concerns regarding the toxic effects of heavy metals on living organisms imposed an urgent need for efficient methods for their removal from wastewaters and aqueous solutions. The most efficient technique for metal ions removal from wastewaters is adsorption due to its reversibility and high efficiency. Numerous adsorbents were mentioned as possible metal ions adsorbents in the literature. Chelating polymer ligands (CPLs) with adaptable surface chemistry, high affinity towards targeted metal ions, high capacity, fast kinetics, chemically stable, and reusable are especially attractive. This review is focused on methacrylate-based magnetic and non-magnetic porous sorbents. Special attention was devoted to amino-modified glycidyl methacrylate (GMA) copolymers. Main adsorption parameters, kinetic models, adsorption isotherms, thermodynamics of the adsorption process, as well as regeneration of the polymeric sorbents were discussed.

Efficient Fluoride Removal by a Fixed-Bed Column of Self-Assembled Zr(IV)-, Fe(III)-, Cu(II)-Complexed Polyvinyl Alcohol Hydrogel Beads

Fixed-bed column adsorption studies are performed with metal-complexed polyvinyl alcohol (PVA) hydrogel beads to remove fluoride from groundwater. The fixed-bed column (bed height = 8 ± 0.2 cm) of copper-zirconium-PVA (PCZH), zirconium-PVA (PZH), and iron-zirconium-PVA (PFZH) hydrogel beads have equilibrium fluoride removal capacities of 17.26 ± 0.05, 31.67 ± 0.05, and 11.84 ± 0.05 mg g^-1 from a 10 ± 0.20 mg L^-1 fluoride solution of pH 6.5 maintained at a flow rate of 1 ± 0.01 mL min^-1. The breakthrough curves for fluoride adsorption are analyzed by non-linear empirical models of Thomas, Bohart-Adams, Yoon-Nelson, and semi-empirical bed depth service time models. The maximum fluoride adsorption capacities obtained from the Thomas model are 25.66 ± 0.05, 38.17 ± 0.05, and 13.75 ± 0.05 mg g^-1 for PCZH, PZH, and PFZH. Moreover, the column of PZH (bed height = 4 ± 0.2 cm) removes about 1.67 ± 0.05 mg g^-1 of fluoride from the alkaline groundwater sample with high total dissolved solids containing 2.84 ± 0.20 mg L^-1 fluoride maintained at a flow rate of 0.5 ± 0.01 mL min^-1. The fluoride removal efficiency decreases marginally (<1 ± 0.02%) in the presence of interfering ions such as chlorides, sulfates, phosphates, bicarbonates, and nitrates. Furthermore, the fixed-bed column (bed height = 4 ± 0.2 cm) of PCZH, PZH, and PFZH remove 7.40 ± 0.05, 14.85 ± 0.05, and 6.53 ± 0.05 mg g^-1 fluoride, respectively, even after the third regeneration cycle. Additionally, the hydrogel beads are effective in the removal of arsenate (≤90 ± 0.02%) and chromate ions (≤96 ± 0.02%) from 100 ± 0.20 mg L^-1 solution in batch adsorption studies. Therefore, the hydrogel beads could be used as potent filters for the removal of fluoride, chromate, and arsenate ions from water.

Facile Synthesis of Hydrogel-Based Ion-Exchange Resins for Nitrite/Nitrate Removal and Studies of Adsorption Behavior

This research aimed to create facile, reusable, hydrogel-based anion exchange resins that have been modified with two different amines to test their ability to adsorb nitrate and nitrite in water using batch and continuous systems. In the batch experiment, maximum adsorption capacities of nitrate and nitrite onto poly (ethylene glycol) diacrylate methacryloxyethyltrimethyl ammonium chloride (PEGDA-MTAC) and poly (ethylene glycol) diacrylate 2-aminoethyl methacrylate hydrochloride (PEGDA-AMHC) adsorbents can be obtained as 13.51 and 13.16 mg NO₃⁻-N/g sorbent; and 12.36 and 10.99 mg NO₂⁻-N/g sorbent respectively through the Langmuir isotherm model. After 15 adsorption/desorption cycles, PEGDA-MTAC and PEGDA-AMHC retained nitrate adsorption efficiencies of 94.71% and 83.02% and nitrite adsorption efficiencies of 97.38% and 81.15% respectively. In a column experiment, modified adsorbents demonstrated adsorption efficiencies greater than 45% after being recycled five times. Proposed hydrogel-based adsorbents can be more effective than several types of carbon-based sorbents for nitrate and nitrite removal in water and have benefits such as reduced waste generation, cost-effectiveness, and a facile synthesis method.