Powered knee and ankle prostheses enable natural ambulation on level ground and stairs for individuals with bilateral above-knee amputation: a case study

Controlling Powered Prosthesis Kinematics Over Continuous Inter-Leg Transitions Between Walking and Stair Ascent/Descent

Although powered prosthetic legs have enabled more biomimetic joint kinematics during steady-state activities like walking and stair climbing, transitions between these activities are usually handled by discretely switching controllers without considering biomimicry or the distinct role of the leading leg. This study introduces two data-driven, phase-based kinematic control approaches for seamless inter-leg transitions (i.e., initiated by either the prosthetic or intact leg) between walking and stair ascent/descent, assuming high-level knowledge of the upcoming activity. One approach employs a novel continuously-varying kinematic model that interpolates between steady-state activities as an approximate convex combination, and the other approach employs a simple switching-based model with optimized switching timing and tunable smoothing of kinematic discontinuities. Data-driven analysis indicates the continuously-varying controller remains beneficial over the switching controller for a range of classification delays. Experimental validation with a powered knee-ankle prosthesis used by two high-functioning transfemoral amputees demonstrates the continuous controller can provide more biomimetic and uninterrupted kinematic trajectories for both joints during transitions, irrespective of the initiating leg. This research underscores the potential for enabling more natural locomotion for high-functioning prosthetic leg users.

Design and prototype validation of a laterally mounted powered hip joint prothesis

Prosthetic technology has advanced with the development of powered prostheses to enhance joint function and movement in the absence of native anatomy. However, there are no powered solutions available for hip-level amputees, and most existing hip prostheses are mounted to the front of the prosthetic socket, thereby limiting range of motion. This research introduces a novel laterally mounted powered hip joint (LMPHJ) that augments user movement. The LMPHJ is mounted on the lateral side of the prosthetic socket, positioning the hip joint closer to the anatomical center of rotation while ensuring user safety and stability. The motor and electronics are located in the thigh area, maintaining a low profile while transmitting the required hip moment to the mechanical joint center of rotation. A prototype was designed and manufactured, and static testing was complete by modifying the loading conditions defined in the ISO 15032:2000 standard to failure test levels for a 100 kg person, demonstrating the joint's ability to withstand everyday loading conditions. Functional testing was conducted using a prosthesis simulator that enabled able-bodied participants to successfully walk with the powered prosthesis on level ground. This validates the mechanical design for walking and indicates the LMPHJ is ready for evaluation in the next phase with hip disarticulation amputee participants.

Continuous A-Mode Ultrasound-Based Prediction of Transfemoral Amputee Prosthesis Kinematics Across Different Ambulation Tasks

OBJECTIVE

Volitional control systems for powered prostheses require the detection of user intent to operate in real life scenarios. Ambulation mode classification has been proposed to address this issue. However, these approaches introduce discrete labels to the otherwise continuous task that is ambulation. An alternative approach is to provide users with direct, voluntary control of the powered prosthesis motion. Surface electromyography (EMG) sensors have been proposed for this task, but poor signal-to-noise ratios and crosstalk from neighboring muscles limit performance. B-mode ultrasound can address some of these issues at the cost of reduced clinical viability due to the substantial increase in size, weight, and cost. Thus, there is an unmet need for a lightweight, portable neural system that can effectively detect the movement intention of individuals with lower-limb amputation.

METHODS

In this study, we show that a small and lightweight A-mode ultrasound system can continuously predict prosthesis joint kinematics in seven individuals with transfemoral amputation across different ambulation tasks. Features from the A-mode ultrasound signals were mapped to the user's prosthesis kinematics via an artificial neural network.

RESULTS

Predictions on testing ambulation circuit trials resulted in a mean normalized RMSE across different ambulation modes of 8.7 ± 3.1%, 4.6 ± 2.5%, 7.2 ± 1.8%, and 4.6 ± 2.4% for knee position, knee velocity, ankle position, and ankle velocity, respectively.

CONCLUSION AND SIGNIFICANCE

This study lays the foundation for future applications of A-mode ultrasound for volitional control of powered prostheses during a variety of daily ambulation tasks.

A Unified Controller for Natural Ambulation on Stairs and Level Ground with a Powered Robotic Knee Prosthesis

Powered lower-limb prostheses have the potential to improve amputee mobility by closely imitating the biomechanical function of the missing biological leg. To accomplish this goal, powered prostheses need controllers that can seamlessly adapt to the ambulation activity intended by the user. Most powered prosthesis control architectures address this issue by switching between specific controllers for each activity. This approach requires online classification of the intended ambulation activity. Unfortunately, any misclassification can cause the prosthesis to perform a different movement than the user expects, increasing the likelihood of falls and injuries. Therefore, classification approaches require near-perfect accuracy to be used safely in real life. In this paper, we propose a unified controller for powered knee prostheses which allows for walking, stair ascent, and stair descent without the need for explicit activity classification. Experiments with one individual with an above-knee amputation show that the proposed controller enables seamless transitions between activities. Moreover, transition between activities is possible while leading with either the sound-side or the prosthesis. A controller with these characteristics has the potential to improve amputee mobility.

Prosthetic Rehabilitation of a Female With Bilateral Transfemoral Amputation in Japan: A Case Report

Individuals with bilateral transfemoral (TF) amputation experience difficulties when walking with lower limb prostheses. Walking with prostheses is even more difficult when the cause of the amputation is nontraumatic, or the gender is female. We provided prosthetic rehabilitation to a woman who underwent bilateral TF amputation due to internal disease.  A 42-year-old woman underwent bilateral TF amputation for ischemic necrosis of the lower extremities during septic shock treatment. Upon admission to our convalescent rehabilitation ward 3 months after surgery, the patient weighed 32 kg and was underweight. After admission, she underwent strength training of the trunk and hip muscles, hip joint range of motion exercises, and bottom shuffle exercises on the physical therapy table. The prosthetist created stubby prostheses for standing and standing-up exercises on the floor, as well as gait exercises. We gradually extended the length of her prostheses and subsequently switched her knee joints to Ottobock locking and polycentric knees and eventually to Kenevo, which are microprocessor-controlled prosthetic knees (MPK). During occupational sessions, she practiced household activities such as washing dishes, cleaning, and cooking while wearing her prostheses. Six months after admission, the patient was discharged and could walk outdoors alone with two canes without using a wheelchair. At discharge, the Kenevo modes were Mode C on the right and Mode B + on the left. The patient's weight recovered to 41 kg. The patient completed the 10-meter walk test at 0.50 m/s at a comfortable walking speed, the 6-minute walk test at 180 meters, and the timed up and go (TUG) test in 26 seconds. The motor Functional Independence Measure (FIM) score was improved from 60 on admission to 83 on discharge.  Strengthening the hip and trunk muscles, improving endurance and balance, preventing hip contracture, and maintaining the hip range of motion are necessary for walking with bilateral TF prostheses. In the prosthetic rehabilitation of bilateral TF amputations, stubby prostheses, protocols for gradual extension of the prosthetic length, and Kenevo, a mode-changeable MPK, are helpful. MPK is essential for individuals with bilateral TF amputations to walk independently and use their prostheses daily. This report is a valuable reference for healthcare professionals involved with bilateral TF amputees in the future who need prosthetic rehabilitation.

Volitional EMG Control Enables Stair Climbing with a Robotic Powered Knee Prosthesis

Existing controllers for robotic powered prostheses regulate the prosthesis speed, timing, and energy generation using predefined position or torque trajectories. This approach enables climbing stairs step-over-step. However, it does not provide amputees with direct volitional control of the robotic prosthesis, a functionality necessary to restore full mobility to the user. Here we show that proportional electromyographic (EMG) control of the prosthesis knee torque enables volitional control of a powered knee prosthesis during stair climbing. The proposed EMG controller continuously regulates knee torque based on activation of the residual hamstrings, measured using a single EMG electrode located within the socket. The EMG signal is mapped to a desired knee flexion/extension torque based on the prosthesis knee position, the residual limb position, and the interaction with the ground. As a result, the proposed EMG controller enabled an above-knee amputee to climb stairs at different speeds, while carrying additional loads, and even backwards. By enabling direct, volitional control of powered robotic knee prostheses, the proposed EMG controller has the potential to improve amputee mobility in the real world.

Investigation with able-bodied subjects suggests Myosuit may potentially serve as a stair ascent training robot

Real world settings are seldomly just composed of level surfaces and stairs are frequently encountered in daily life. Unfortunately, ~ 90% of the elderly population use some sort of compensation pattern in order to negotiate stairs. Because the biomechanics required to successfully ascend stairs is significantly different from level walking, an independent training protocol is warranted. Here, we present as a preliminary investigation with 11 able-bodied subjects, prior to clinical trials, whether Myosuit could potentially serve as a stair ascent training robot. Myosuit is a soft wearable exosuit that was designed to assist the user via hip and knee extension during the early stance phase. We hypothesized that clinical studies could be carried out if the lower limb kinematics, sensory feedback via plantar force, and electromyography (EMG) patterns do not deviate from the user's physiological stair ascent patterns while reducing hip and knee extensor demand. Our results suggest that Myosuit conserves the user's physiological kinematic and plantar force patterns. Moreover, we observe approximately 20% and 30% decrease in gluteus maximus and vastus medialis EMG levels in the pull up phase, respectively. Collectively, Myosuit reduces the hip and knee extensor demand during stair ascent without any introduction of significant compensation patterns.

The impact of walking on the perception of multichannel electrotactile stimulation in individuals with lower-limb amputation and able-bodied participants

BACKGROUND

One of the drawbacks of lower-limb prostheses is that they do not provide explicit somatosensory feedback to their users. Electrotactile stimulation is an attractive technology to restore such feedback because it enables compact solutions with multiple stimulation points. This allows stimulating a larger skin area to provide more information concurrently and modulate parameters spatially as well as in amplitude. However, for effective use, electrotactile stimulation needs to be calibrated and it would be convenient to perform this procedure while the subject is seated. However, amplitude and spatial perception can be affected by motion and/or physical coupling between the residual limb and the socket. In the present study, we therefore evaluated and compared the psychometric properties of multichannel electrotactile stimulation applied to the thigh/residual limb during sitting versus walking.

METHODS

The comprehensive assessment included the measurement of the sensation and discomfort thresholds (ST & DT), just noticeable difference (JND), number of distinct intervals (NDI), two-point discrimination threshold (2PD), and spatial discrimination performance (SD). The experiment involved 11 able-bodied participants (4 females and 7 males; 29.2 ± 3.8 years), 3 participants with transtibial amputation, and 3 participants with transfemoral amputation.

RESULTS

In able-bodied participants, the results were consistent for all the measured parameters, and they indicated that both amplitude and spatial perception became worse during walking. More specifically, ST and DT increased significantly during walking vs. sitting (2.90 ± 0.82 mA vs. 2.00 ± 0.52 mA; p < 0.001 for ST and 7.74 ± 0.84 mA vs. 7.21 ± 1.30 mA; p < 0.05 for DT) and likewise for the JND (22.47 ± 12.21% vs. 11.82 ± 5.07%; p < 0.01), while the NDI became lower (6.46 ± 3.47 vs. 11.27 ± 5.18 intervals; p < 0.01). Regarding spatial perception, 2PD was higher during walking (69.78 ± 17.66 mm vs. 57.85 ± 14.87 mm; p < 0.001), while the performance of SD was significantly lower (56.70 ± 10.02% vs. 64.55 ± 9.44%; p < 0.01). For participants with lower-limb amputation, the ST, DT, and performance in the SD assessment followed the trends observed in the able-bodied population. The results for 2PD and JND were however different and subject-specific.

CONCLUSION

The conducted evaluation demonstrates that electrotactile feedback should be calibrated in the conditions in which it will be used (e.g., during walking). The calibration during sitting, while more convenient, might lead to an overly optimistic (or in some cases pessimistic) estimate of sensitivity. In addition, the results underline that calibration is particularly important in people affected by lower-limb loss to capture the substantial variability in the conditions of the residual limb and prosthesis setup. These insights are important for the implementation of artificial sensory feedback in lower-limb prosthetics applications.

Design, Kinematics and Gait Analysis, of Prosthetic Knee Joints: A Systematic Review

The aim of this review article is to appraise the design and functionality of above-knee prosthetic legs. So far, various transfemoral prosthetic legs are found to offer a stable gait to amputees but are limited to laboratories. The commercially available prosthetic legs are not reliable and comfortable enough to satisfy amputees. There is a dire need for creating a powered prosthetic knee joint that could address amputees' requirements. To pinpoint the gap in transfemoral prosthetic legs, prosthetic knee unit model designs, control frameworks, kinematics, and gait evaluations are concentrated. Ambulation exercises, ground-level walking, running, and slope walking are considered to help identify research gaps and areas where existing prostheses can be ameliorated. The results show that above-knee amputees can more effectively manage their issues with the aid of an active prosthesis, capable of reliable gait. To accomplish the necessary control, closed loop controllers and volitional control are integral parts. Future studies should consider designing a transfemoral electromechanical prosthesis based on electromyographic (EMG) signals to better predict the amputee's intent and control in accordance with that intent.

Can a powered knee-ankle prosthesis improve weight-bearing symmetry during stand-to-sit transitions in individuals with above-knee amputations?

BACKGROUND

After above-knee amputation, the missing biological knee and ankle are replaced with passive prosthetic devices. Passive prostheses are able to dissipate limited amounts of energy using resistive damper systems during "negative energy" tasks like sit-down. However, passive prosthetic knees are not able to provide high levels of resistance at the end of the sit-down movement when the knee is flexed, and users need the most support. Consequently, users are forced to over-compensate with their upper body, residual hip, and intact leg, and/or sit down with a ballistic and uncontrolled movement. Powered prostheses have the potential to solve this problem. Powered prosthetic joints are controlled by motors, which can produce higher levels of resistance at a larger range of joint positions than passive damper systems. Therefore, powered prostheses have the potential to make sitting down more controlled and less difficult for above-knee amputees, improving their functional mobility.

METHODS

Ten individuals with above-knee amputations sat down using their prescribed passive prosthesis and a research powered knee-ankle prosthesis. Subjects performed three sit-downs with each prosthesis while we recorded joint angles, forces, and muscle activity from the intact quadricep muscle. Our main outcome measures were weight-bearing symmetry and muscle effort of the intact quadricep muscle. We performed paired t-tests on these outcome measures to test for significant differences between passive and powered prostheses.

RESULTS

We found that the average weight-bearing symmetry improved by 42.1% when subjects sat down with the powered prosthesis compared to their passive prostheses. This difference was significant (p = 0.0012), and every subject's weight-bearing symmetry improved when using the powered prosthesis. Although the intact quadricep muscle contraction differed in shape, neither the integral nor the peak of the signal was significantly different between conditions (integral p > 0.01, peak p > 0.01).

CONCLUSIONS

In this study, we found that a powered knee-ankle prosthesis significantly improved weight-bearing symmetry during sit-down compared to passive prostheses. However, we did not observe a corresponding decrease in intact-limb muscle effort. These results indicate that powered prosthetic devices have the potential to improve balance during sit-down for individuals with above-knee amputation and provide insight for future development of powered prosthetics.