Cleaning of LTCC, PEN, and PCB Au electrodes towards reliable electrochemical measurements

A plug-and-play, easy-to-manufacture fluidic accessory to significantly enhance the sensitivity of electrochemical immunoassays

Earlier access to patients' biomarker status could transform disease management. However, gold-standard techniques such as enzyme-linked immunosorbent assays (ELISAs) are typically not deployed at the point-of-care due to their cumbersome instrumentation and complexity. Electrochemical immunosensors can be disruptive in this sector with their small size and lower cost but, without further modifications, the performance of these sensors in complex media (e.g., blood) has been limited. This paper presents a low-cost fluidic accessory fabricated using widely accessible materials and processes for boosting sensor sensitivity through confinement of the detection media next to the electrode surface. Liquid confinement first highlighted a spontaneous reaction between the pseudoreference electrode and ELISA detection substrate 3,3',5,5'-tetramethylbenzidine (TMB) that decreases the amount of oxTMB available for detection. Different strategies are investigated to limit this and maximize reliability. Next, flow cell integration during the signal amplification step of sensor preparation was shown to substantially enhance the detection of cytokine interleukin-6 (IL-6) with the best sensitivity boost recorded for fresh human plasma (x7 increase compared to x5.8 in purified serum and x5.5 in PBS). The flow cell requires no specialized equipment and can be seamlessly integrated with commercial sensors, making an ideal companion for electrochemical signal enhancement.

Insulator-on-Conductor Fouling Amplifies Aqueous Electrolysis Rates

The chemical industry is a major consumer of fossil fuels. Several chemical reactions of practical value proceed with the gain or loss of electrons, opening a path to integrate renewable electricity into chemical manufacturing. However, most organic molecules have low aqueous solubility, causing green and cheap electricity-driven reactions to suffer from intrinsically low reaction rates in industry's solvent of choice: water. Here, we show that a strategic, partial electrode fouling with hydrophobic insulators (oils and plastics) offsets kinetic limitations caused by poor reactant solubility, opening a new path for the direct integration of renewable electricity into the production of commodity chemicals. Through electrochemiluminescence microscopy, we reveal for the oxidation of organic reactants up to 6-fold reaction rate increase at the "fouled" oil-electrolyte-electrode interface relative to clean electrolyte-electrode areas. Analogously, electrodes partially masked (fouled) with plastic patterns, deposited either photolithographically (photoresists) or manually (inexpensive household glues and sealants), outperform clean electrodes. The effect is not limited to reactants of limited water solubility, and, for example, net gold electrodeposition rates are up to 22% larger at fouled than clean electrodes. In a system involving a surface-active reactant, rate augmentation is driven by the synergy between insulator-confined reactant enrichment and insulator-induced current crowding, whereas only the latter and possibly localized decrease in iR drop near the insulator are relevant in a system composed of non-surface-active species. Our counterintuitive electrode design enhances electrolysis rates despite the diminished area of intimate electrolyte-electrode contact and introduces a new path for upscaling aqueous electrochemical processes.

Validation of a platinum bioelectrode model for preclinical electrical and biological performance evaluation. ANNUAL INTERNATIONAL CONFERENCE OF THE IEEE ENGINEERING IN MEDICINE AND BIOLOGY SOCIETY. IEEE ENGINEERING IN MEDICINE AND BIOLOGY SOCIETY. ANNUAL INTERNATIONAL CONFERENCE 2023;2023:1-4. [PMID: 38083526 DOI: 10.1109/embc40787.2023.10340761] [Citation(s) in RCA: 0] [Impact Index Per Article: 0]

High throughput testing of clinically representative Pt electrodes requires an inexpensive, efficient method of production. The aim of this study was to develop a facile platinum (Pt) model electrode (PME) and assess its production process, stability, and reproducibility. In this study a new model electrode was developed using representative substrates and dimensions as state-of-the-art electrode arrays used for neural stimulation. It was found that the PME is a highly reproducible robust system with similar electrochemical performance but with lower variability than other neural prosthetic arrays.Clinical Relevance- As an estimate these novel model electrodes cost 300 times less than a cochlear implant, can be manufactured in a tenth of the time and with a less than 10% failure rate. It is expected that model electrodes with low variability of electrical properties will significantly improve preclinical validation testing of electrochemical stimulation, surface modifications, and coatings.