Ultraviolet Absorption Cross Sections of KOH and KCl for Nonintrusive Species-Specific Quantitative Detection in Hot Flue Gases

An understanding of potassium chemistry in energy conversion processes supports the development of complex biomass utilization with high efficiency and low pollutant emissions. Potassium exists mainly as potassium hydroxide (KOH), potassium chloride (KCl), and atomic potassium (K) in combustion and related thermochemical processes. We report, for the first time, the measurement of the ultraviolet (UV) absorption cross sections of KOH and KCl at temperatures between 1300 K and 1800 K, using a newly developed method. Using the spectrally resolved UV absorption cross sections, the concentrations of KOH and KCl were measured simultaneously. In addition, we measured the concentrations of atomic K using tunable diode laser absorption spectroscopy, both at 404.4 and 769.9 nm. The 404.4 nm line was utilized to expand the measurement dynamic range to higher concentrations. A constant amount of KCl was seeded into premixed CH4/air flames with equivalence ratios varied from 0.67 to 1.32, and the concentrations of KOH, KCl, and atomic K in the hot flue gas were measured nonintrusively. The results indicate that these techniques can provide comprehensive data for quantitative understanding of the potassium chemistry in biomass combustion/gasification.

Spectrally Resolved Ultraviolet (UV) Absorption Cross-Sections of Alkali Hydroxides and Chlorides Measured in Hot Flue Gases

Spectrally resolved ultraviolet (UV) absorption cross-sections of gas-phase sodium chloride (NaCl), potassium hydroxide (KOH), and sodium hydroxide (NaOH) were measured, for the first time, in hot flue gases at different temperatures. Homogenous gas-phase NaCl, KCl (potassium chloride), NaOH, and KOH at temperatures 1200 K, 1400 K, 1600 K, and 1850 K were prepared in the post-flame zone of laminar flames by seeding nebulized droplets out of aqueous solution of corresponding alkali species. The amount of droplets seeded into the flame was kept constant, so the relative concentration of different alkali species can be derived. The broadband UV absorption cross-section of KCl vapor reported by Leffler et al. was adopted to derive the absorption cross-section curves of NaCl, NaOH, and KOH with the corresponding measured spectrally resolved absorbance spectra. No significant changes in the spectral structures in the absorption cross-sections were found as the temperature varied between 1200 K and 1850 K, except for NaOH at around 320 nm. The difference between the absorption spectral curves of alkali chlorides and hydroxides is significant at wavelengths above 300 nm, which thus can be used to distinguish and obtain the concentrations of alkali chlorides and hydroxides in the broadband UV absorption measurements.

Laser-Induced Photofragmentation Fluorescence Imaging of Alkali Compounds in Flames

Laser-induced photofragmentation fluorescence has been investigated for the imaging of alkali compounds in premixed laminar methane-air flames. An ArF excimer laser, providing pulses of wavelength 193 nm, was used to photodissociate KCl, KOH, and NaCl molecules in the post-flame region and fluorescence from the excited atomic alkali fragment was detected. Fluorescence emission spectra showed distinct lines of the alkali atoms allowing for efficient background filtering. Temperature data from Rayleigh scattering measurements together with simulations of potassium chemistry presented in literature allowed for conclusions on the relative contributions of potassium species KOH and KCl to the detected signal. Experimental approaches for separate measurements of these components are discussed. Signal power dependence and calculated fractions of dissociated molecules indicate the saturation of the photolysis process, independent on absorption cross-section, under the experimental conditions. Quantitative KCl concentrations up to 30 parts per million (ppm) were evaluated from the fluorescence data and showed good agreement with results from ultraviolet absorption measurements. Detection limits for KCl photofragmentation fluorescence imaging of 0.5 and 1.0 ppm were determined for averaged and single-shot data, respectively. Moreover, simultaneous imaging of KCl and NaCl was demonstrated using a stereoscope with filters. The results indicate that the photofragmentation method can be employed for detailed studies of alkali chemistry in laboratory flames for validation of chemical kinetic mechanisms crucial for efficient biomass fuel utilization.

A novel multi-jet burner for hot flue gases of wide range of temperatures and compositions for optical diagnostics of solid fuels gasification/combustion

A novel multi-jet burner was built to provide one-dimensional laminar flat flames with a wide range of variable parameters for multipurpose quantitative optical measurements. The burner is characterized by two independent plenum chambers, one supporting a matrix of 181 laminar jet flames and the other supporting a co-flow from a perforated plate with small holes evenly distributed among the jets. A uniform rectangular burned gas region of 70 mm × 40 mm can be generated, with a wide range of temperatures and equivalence ratios by controlling independently the gas supplies to the two plenum chambers. The temperature of the hot gas can be adjusted from 1000 K to 2000 K with different flame conditions. The burner is designed to seed additives in gas or liquid phase to study homogeneous reactions. The large uniform region can be used to burn solid fuels and study heterogeneous reactions. The temperature was measured using two-line atomic fluorescence thermometry and the temperature profile at a given height above the burner was found to be flat. Different types of optical diagnostic techniques, such as line of sight absorption or laser-induced fluorescence, can be easily applied in the burner, and as examples, two typical measurements concerning biomass combustion are demonstrated.

Development of an alkali chloride vapour-generating apparatus for calibration of ultraviolet absorption measurements

A novel design of alkali chloride vapour-generating cell has been developed, which can serve as a calibration cell for quantitative ultraviolet absorption concentration measurements and meticulous spectral investigations of alkali compounds. The calibration cell was designed to provide alkali vapour of well-controlled concentrations and temperatures, and consisted of a sealed quartz cell measuring 0.4 m in length with a temperature-controlled reservoir containing solid alkali salt. The cell was placed in a furnace and the alkali vapours generated from the reservoir have direct access to the measuring chamber. Investigations of potassium chloride (KCl) were made on sublimated vapour at temperatures 650, 700, 750, 780, and 800 °C while the reservoir temperature was kept 50 °C lower to avoid condensation. The cell provides stable KCl vapour pressures, and the furnace provides a homogenous temperature profile along the cell. KCl vapour pressures are well characterised and conform the base for determination of the KCl concentration in the cell. The alkali chloride levels matched the concentration range of the absorption setup and indicated a previously employed calibration method to overestimate KCl concentrations. The KCl absorption cross sections for wavelengths λ=197.6 nm and λ=246.2 nm were calculated to be 3.4 × 10^-17 and 2.9 × 10^-17 cm²/molecule, respectively. The absorption cross section spectra did not show any structural differences with increasing temperature, which could indicate influence of dimers or significant changes of the population in the KCl vibrational states. The KCl absorption cross sections thus did not show any temperature dependence in the temperature region of 700-800 °C. Moreover, the applicability of the calibration cell for measurement of other alkali chlorides and hydroxides is discussed.

Reaction Kinetics of Meteoric Sodium Reservoirs in the Upper Atmosphere

The gas-phase reactions of a selection of sodium-containing species with atmospheric constituents, relevant to the chemistry of meteor-ablated Na in the upper atmosphere, were studied in a fast flow tube using multiphoton ionization time-of-flight mass spectrometry. For the first time, unambiguous observations of NaO and NaOH in the gas phase under atmospheric conditions have been achieved. This enabled the direct measurement of the rate constants for the reactions of NaO with H2, H2O, and CO, and of NaOH with CO2, which at 300-310 K were found to be (at 2σ confidence level): k(NaO + H2O) = (2.4 ± 0.6) × 10(-10) cm(3) molecule (-1) s(-1), k(NaO + H2) = (4.9 ± 1.2) × 10(-12) cm(3) molecule (-1) s(-1), k(NaO + CO) = (9 ± 4) × 10(-11) cm(3) molecule (-1) s(-1), and k(NaOH + CO2 + M) = (7.6 ± 1.6) × 10(-29) cm(6) molecule (-2) s(-1) (P = 1-4 Torr). The NaO + H2 reaction was found to make NaOH with a branching ratio ≥ 99%. A combination of quantum chemistry and statistical rate theory calculations are used to interpret the reaction kinetics and extrapolate the atmospherically relevant experimental results to mesospheric temperatures and pressures. The NaO + H2O and NaOH + CO2 reactions act sequentially to provide the major atmospheric sink of meteoric Na and therefore have a significant impact on the underside of the Na layer in the terrestrial mesosphere: the newly determined rate constants shift the modeled peak to about 93 km, i.e., 2 km higher than observed by ground-based lidars. This highlights further uncertainties in the Na chemistry cycle such as the unknown rate constant of the NaOH + H reaction. The fast Na-recycling reaction between NaO and CO and a re-evaluated rate constant of the NaO + CO2 sink should be now considered in chemical models of the Martian Na layer.

In situ measurement technique for simultaneous detection of K, KCl, and KOH vapors released during combustion of solid biomass fuel in a single particle reactor

A quantitative and simultaneous measurement of K, KCl, and KOH vapors from a burning fuel sample combusted in a single particle reactor was performed using collinear photofragmentation and atomic absorption spectroscopy (CPFAAS) with a time resolution of 0.2 s. The previously presented CPFAAS technique was extended in this work to cover two consecutive fragmentation pulses for the photofragmentation of KCl and KOH. The spectral overlapping of the fragmentation spectra of KCl and KOH is discussed, and a linear equation system for the correction of the spectral interference is introduced. The detection limits for KCl, KOH, and K with the presented measurement arrangement and with 1 cm sample length were 0.5, 0.1, and 0.001 parts per million, respectively. The experimental setup was applied to analyze K, KCl, and KOH release from 10 mg spruce bark samples combusted at the temperatures of 850, 950, and 1050 °C with 10% of O2. The combustion experiments provided data on the form of K vapors and their release during different combustion phases and at different temperatures. The measured release histories agreed with earlier studies of K release. The simultaneous direct measurement of atomic K, KCl, and KOH will help in the impact of both the form of K in the biomass and fuel variables, such as particle size, on the release of K from biomass fuels.

Structures and heats of formation of simple alkali metal compounds: hydrides, chlorides, fluorides, hydroxides, and oxides for Li, Na, and K

Geometry parameters, frequencies, heats of formation, and bond dissociation energies are predicted for simple alkali metal compounds (hydrides, chlorides, fluorides, hydroxides and oxides) of Li, Na, and K from coupled cluster theory [CCSD(T)] calculations including core-valence correlation with the aug-cc-pwCVnZ basis set (n = D, T, Q, and 5). To accurately calculate the heats of formation, the following additional correction were included: scalar relativistic effects, atomic spin-orbit effects, and vibrational zero-point energies. For calibration purposes, the properties of some of the lithium compounds were predicted with iterative triple and quadruple excitations via CCSDT and CCSDTQ. The calculated geometry parameters, frequencies, heats of formation, and bond dissociation energies were compared with all available experimental measurements and are in excellent agreement with high-quality experimental data. High-level calculations are required to correctly predict that K(2)O is linear and that the ground state of KO is (2)Sigma(+), not (2)Pi, as in LiO and NaO. This reliable and consistent set of calculated thermodynamic data is appropriate for use in combustion and atmospheric simulations.