Anodic electron transfer mechanisms in microbial fuel cells and their energy efficiency

Acceleration mechanism of riboflavin on Fe0-to-microbe electron transfer in corrosion of EH36 steel by Pseudomonas aeruginosa

Riboflavin (RF), as a common electron mediator that can accelerate extracellular electron transfer (EET), is usually used as a probe to confirm EET-microbiologically influenced corrosion (MIC). However, the acceleration mechanism of RF on EET-MIC is still unclear, especially the effect on gene expression in bacteria. In this study, a 13-mer antimicrobial peptide E6 and tetrakis hydroxymethyl phosphonium sulfate (THPS) were used as new tools to investigate the acceleration mechanism of RF on Fe0-to-microbe EET in corrosion of EH36 steel caused by Pseudomonas aeruginosa. 60 min after 20 ppm (v/v) THPS and 20 ppm THPS & 100 nM E6 were injected into P. aeruginosa 1 and P. aeruginosa 2 (two glass bottles containing P. aeruginosa with different treatments) at the 3-d incubation, respectively, P. aeruginosa 1 and P. aeruginosa 2 had a similar planktonic cell count, whereas the sessile cell count in P. aeruginosa 1 was 1.3 log higher than that in P. aeruginosa 2. After the 3-d pre-growth and subsequent 7-d incubation, the addition of 20 ppm (w/w) RF increased the weight loss and maximum pit depth of EH36 steel in P. aeruginosa 1 by 0.7 mg cm-2 and 4.1 μm, respectively, while only increasing those in P. aeruginosa 2 by 0.4 mg cm-2 and 1.7 μm, respectively. This suggests that RF can be utilized by P. aeruginosa biofilms since the corrosion rate should be elevated by the same value if it only acts on the planktonic cells. Furthermore, the EET capacity of P. aeruginosa biofilm was enhanced by RF because the protein expression of cytochrome c (Cyt c) gene in sessile cells was significantly increased in the presence of RF, which accelerated EET-MIC by P. aeruginosa against EH36 steel.

A critical review of approaches to enhance the performance of bio-electro-Fenton and photo-bio-electro-Fenton systems

The development of sustainable advanced energy conversion technologies and efficient pollutant treatment processes is a viable solution to the two global crises of the lack of non-renewable energy resources and environmental harm. In recent years, the interaction of biological and chemical oxidation units to utilize biomass has been extensively studied. Among these systems, bio-electro-Fenton (BEF) and photo-bio-electro-Fenton (PBEF) systems have shown prospects for application due to making rational and practical conversion and use of energy. This review compared and analyzed the electron transfer mechanisms in BEF and PBEF systems, and systematically summarized the techniques for enhancing system performance based on the generation, transfer, and utilization of electrons, including increasing the anode electron recovery efficiency, enhancing the generation of reactive oxygen species, and optimizing operational modes. This review compared the effects of different methods on the electron flow process and fully evaluated the benefits and drawbacks. This review may provide straightforward suggestions and methods to enhance the performance of BEF and PBEF systems and inspire the reader to explore the generation and utilization of sustainable energy more deeply.

Optimization strategies for CO2 biological fixation

Global sustainable development faces a significant challenge in effectively utilizing CO2. Meanwhile, CO2 biological fixation offers a promising solution. CO2 has the highest oxidation state (+4 valence state), whereas typical multi‑carbon chemicals have lower valence states. The Gibbs free energy (ΔG) changes of CO2 reductive reactions are generally positive and this renders it necessary to input different forms of energy. Although biological carbon fixation processes are friendly to operate, the thermodynamic obstacles must be overcome. To make this reaction occur favorably and efficiently, diverse strategies to enhance CO2 biological fixation efficiency have been proposed by numerous researchers. This article reviews recent advances in optimizing CO2 biological fixation and intends to provide new insights into achieving efficient biological utilization of CO2. It first outlines the thermodynamic characteristics of diverse carbon fixation reactions and proposes optimization directions for CO2 biological fixation. A comprehensive overview of the catalytic mechanisms, optimization strategies, and challenges encountered by common carbon-fixing enzymes is then provided. Subsequently, potential routes for improving the efficiency of biological carbon fixation are discussed, including the ATP supply, reducing power supply, energy supply, reactor design, and carbon enrichment system modules. In addition, effective artificial carbon fixation pathways were summarized and analyzed. Finally, prospects are made for the research direction of continuously improving the efficiency of biological carbon fixation.

Enhancing microbial fuel cell performance through microbial immobilization

Bio-electrochemical Systems (BES), particularly Microbial Fuel Cells (MFC), have emerged as promising technologies in environmental biotechnology. This study focused on optimizing the anode bacterial culture immobilization process to enhance BES performance. The investigation combines and modifies two key immobilization methods: covalent bonding with glutaraldehyde and inclusion in a chitosan gel in order to meet the criteria and requirements of the bio-anodes in MFC. The performance of MFCs with immobilized and suspended cultures was compared in parallel experiments. Both types showed similar substrate utilization dynamics with slight advantage of the immobilized bio-anode considering the lower concentration of biomass. The immobilized MFC exhibited higher power generation and metabolic activity, as well. Probably, this is due to improved anodic respiration and higher coulombic efficiency of the reactor. Analysis of organic acids content supported this conclusion showing significant inhibition of the fermentation products production in the MFC reactor with immobilized anode culture.

Promotion of Humic Acid Transformation by Abiotic and Biotic Fe Redox Cycling in Nontronite

The redox activity of Fe-bearing minerals is coupled with the transformation of organic matter (OM) in redox dynamic environments, but the underlying mechanism remains unclear. In this work, a Fe redox cycling experiment of nontronite (NAu-2), an Fe-rich smectite, was performed via combined abiotic and biotic methods, and the accompanying transformation of humic acid (HA) as a representative OM was investigated. Chemical reduction and subsequent abiotic reoxidation of NAu-2 produced abundant hydroxyl radicals (thereafter termed as ·OH) that effectively transformed the chemical and molecular composition of HA. More importantly, transformed HA served as a more premium electron donor/carbon source to couple with subsequent biological reduction of Fe(III) in reoxidized NAu-2 by Geobacter sulfurreducens, a model Fe-reducing bacterium. Destruction of aromatic structures and formation of carboxylates were mechanisms responsible for transforming HA into an energetically more bioavailable substrate. Relative to unaltered HA, transformed HA increased the extent of the bioreduction by 105%, and Fe(III) reduction was coupled with oxidation and even mineralization of transformed HA, resulting in bleached HA and formation of microbial products and cell debris. ·OH transformation slightly decreased the electron shuttling capacity of HA in bioreduction. Our results provide a mechanistic explanation for rapid OM mineralization driven by Fe redox cycling in redox-fluctuating environments.

In situ self-induced electrical stimulation to plants: Modulates morphogenesis, photosynthesis and gene expression in Vigna radiata and Cicer arietinum

Specific stimuli to plants influence intracellular and intercellular communications, activation of ion channels, gene expression, growth and development. The functional role of self-induced in situ electrical stimuli at the rhizosphere of the plant by placing electrode assembly in a defined circuit mode was studied on the growth and development of Vigna radiata and Cicer arietinum plants. Experiments were designed with three-circuit mode configurational variations (CC-P, OC-P and SC-P) and compared with the relative performance of control system (non-potential). The plants cultivated under the in situ electrical stimuli (low-current) showed a marked influence on growth and photosynthetic performance of the plants. CC-P operation showed improved vegetative growth, characterized by increased roots, shoots and biomass along with accelerated plant growth from seed germination to vegetation, flowering and pod formation leading towards earlier and more robust flowering compared to control system. Plants also showed higher aquaporin gene expression levels in CC-P operation. The control operation showed 10 days additional maturation time compared to CC-P operation. The strategy can be beneficially applied to augment the bioremediation capacity of complex pollutants with reference to phytoremediation or constructed wetland systems where the plant and its roots are the main enabler apart from agriculture applications specific to nursery-raised or transplanted plants.

Co-culturing Chlorella vulgaris and Cystobasidium oligophagum JRC1 in the microbial fuel cell cathode for lipid biosynthesis

This study investigated the effect of co-culturing the photobiont and mycobiont in the microbial fuel cell (MFC) cathode on biomass production, lipid generation, and power output. Chlorella vulgaris provides oxygen and nutrients for the yeast Cystobasidium oligophagum JRC1, while the latter offers CO2 and quench oxygen for higher algal growth. The MFC with co-culture enhanced the lipid output of biomass by 28.33%, and the total yield and productivity were 1.47 ± 0.18 g/l and 0.123 g/l/day, respectively. Moreover, with co-culture, the open circuit voltage of 685 ± 11 mV was two times higher than algae alone. The specific growth rate (day-1) at the cathode was 0.367 ± 0.04 in co-culture and 0.288 ± 0.05 with C. vulgaris only. The power density of the system was 5.37 ± 0.21 mW/m2 with 75.88 ± 1.89% of COD removal. The co-culture thus proved beneficial at the MFC cathode in terms of total energy output as 11.5 ± 0.035 kWh/m3, which was 1.4-fold higher than algae alone.

Examining current trends and future outlook of bio-electrochemical systems (BES) for nutrient conversion and recovery: an overview

Nutrient-rich waste streams from domestic and industrial sources and the increasing application of synthetic fertilizers have resulted in a huge-scale influx of reactive nitrogen and phosphorus in the environment. The higher concentrations of these pollutants induce eutrophication and foster degradation of aquatic biodiversity. Besides, phosphorus being non-renewable resource is under the risk of rapid depletion. Hence, recovery and reuse of the phosphorus and nitrogen are necessary. Over the years, nutrient recovery, low-carbon energy, and sustainable bioremediation of wastewater have received significant interest. The conventional wastewater treatment technologies have higher energy demand and nutrient removal entails a major cost in the treatment process. For these issues, bio-electrochemical system (BES) has been considered as sustainable and environment friendly wastewater treatment technologies that utilize the energy contained in the wastewater so as to recovery nutrients and purify wastewater. Therefore, this article comprehensively focuses and critically analyzes the potential sources of nutrients, working mechanism of BES, and different nutrient recovery strategies to unlock the upscaling opportunities. Also, economic analysis was done to understand the technical feasibility and potential market value of recovered nutrients. Hence, this review article will be useful in establishing waste management policies and framework along with development of advanced configurations with major emphasis on nutrient recovery rather than removal from the waste stream.

Enhanced detoxification of Cr6+ by Shewanella oneidensis via adsorption on spherical and flower-like manganese ferrite nanostructures

Maximizing the safe removal of hexavalent chromium (Cr6+) from waste streams is an increasing demand due to the environmental, economic and health benefits. The integrated adsorption and bio-reduction method can be applied for the elimination of the highly toxic Cr6+ and its detoxification. This work describes a synthetic method for achieving the best chemical composition of spherical and flower-like manganese ferrite (MnxFe3-xO4) nanostructures (NS) for Cr6+ adsorption. We selected NS with the highest adsorption performance to study its efficiency in the extracellular reduction of Cr6+ into a trivalent state (Cr3+) by Shewanella oneidensis (S. oneidensis) MR-1. MnxFe3-xO4 NS were prepared by a polyol solvothermal synthesis process. They were characterised by powder X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectrometry (XPS), dynamic light scattering (DLS) and Fourier transform-infrared (FTIR) spectroscopy. The elemental composition of MnxFe3-xO4 was evaluated by inductively coupled plasma atomic emission spectroscopy. Our results reveal that the oxidation state of the manganese precursor significantly affects the Cr6+ adsorption efficiency of MnxFe3-xO4 NS. The best adsorption capacity for Cr6+ is 16.8 ± 1.6 mg Cr6+/g by the spherical Mn0.22+Fe2.83+O4 nanoparticles at pH 7, which is 1.4 times higher than that of Mn0.8Fe2.2O4 nanoflowers. This was attributed to the relative excess of divalent manganese in Mn0.22+Fe2.83+O4 based on our XPS analysis. The lethal concentration of Cr6+ for S. oneidensis MR-1 was 60 mg L-1 (determined by flow cytometry). The addition of Mn0.22+Fe2.83+O4 nanoparticles to S. oneidensis MR-1 enhanced the bio-reduction of Cr6+ 2.66 times compared to the presence of the bacteria alone. This work provides a cost-effective method for the removal of Cr6+ with a minimum amount of sludge production.

Methane emission reduction oriented extracellular electron transfer and bioremediation of sediment microbial fuel cell: A review

Sediment is the internal and external source of water environment pollution, so sediment remediation is the premise of water body purification. Sediment microbial fuel cell (SMFC) can remove the organic pollutants in sediment by electroactive microorganisms, compete with methanogens for electrons, and realize resource recycling, methane emission inhibiting and energy recovering. Due to these characteristics, SMFC have attracted wide attention for sediment remediation. In this paper, we comprehensively summarized the recent advances of SMFC in the following areas: (1) The advantages and disadvantages of current applied sediment remediation technologies; (2) The basic principles and influencing factors of SMFC; (3) The application of SMFC for pollutant removal, phosphorus transformation and remote monitoring and power supply; (4) Enhancement strategies for SMFC in sediments remediation such as SMFC coupled with constructed wetland, aquatic plant and iron-based reaction. Finally, we have summarized the drawback of SMFC and discuss the future development directions of applying SMFC for sediment bioremediation.

Over-expressing NadA quinolinate synthase in Escherichia coli enhances the bioelectrochemistry in microbial fuel cells

The microbial fuel cell (MFC), which converts biomass energy into electricity through microbial metabolism, is one of the important devices for generating new bioenergy. However, low power production efficiency limits the development of MFCs. One possible method to solve this problem is to genetically modify the microbial metabolism pathways to enhance the efficiency of MFCs. In this study, we over-expressed the nicotinamide adenine dinucleotide A quinolinate synthase gene (nadA) in order to increase the NADH/+ level in Escherichia coli and obtain a new electrochemically active bacteria strain. The following experiments showed an enhanced performance of the MFC, including increased peak voltage output (70.81 mV) and power density (0.29 μW/cm2), which increased by 361% and 20.83% compared to the control group, respectively. These data suggest that genetic modification of electricity producing microbes could be a potential way to improve MFC performance.

New Application of Polyoxometalate Salts as Cathode Materials in Single Chamber MFC Using Wastewater for Bioenergy Production

Microbial fuel cells (MFCs) are a promising technology that can be applied in a bifunctional process in which wastewater treatment is used for renewable electric power generation. In this study, novel transition metal-modified Keggin-type lacunar polyoxometalate salts (L-POMs) Cs5PMo11M(H2O)O39 (M = Fe, Co), were synthesized and characterized by X-ray diffraction, SEM, EDX, IR, TGA/DSC, and UV-Vis/DSR spectroscopies to be tested, for the first time, as a cathode component in wastewater-fed air chamber MFCs. Both materials were tested in the presence and absence of light to evaluate their photocatalytic behavior. The best performance in terms of electricity production was obtained for the MFC containing the Co-modified POM-based cathode, which showed a maximum power of 418.15 mW/m2 equivalent to 331 mW per cubic meter of treated wastewater, and a maximum COD removal percentage of 97% after 96 h of MFC operation. Co- and Fe-modified POMs had outstanding optical behavior with lower energy gap values, 1.71 and 2.68 eV, respectively. The newly developed materials can be considered as promising alternative cathode catalysts in a new generation of MFC devices integrating full carbon removal from wastewater and a fast reduction of oxygen.

Bioelectrocatalysis for CO2 reduction: recent advances and challenges to develop a sustainable system for CO2 utilization

Activation and turning CO₂ into value added products is a promising orientation to address environmental issues caused by CO₂ emission. Currently, electrocatalysis has a potent well-established role for CO₂ reduction with fast electron transfer rate; but it is challenged by the poor selectivity and low faradic efficiency. On the other side, biocatalysis, including enzymes and microbes, has been also employed for CO₂ conversion to target C_n products with remarkably high selectivity; however, low solubility of CO₂ in the liquid reaction phase seriously affects the catalytic efficiency. Therefore, a new synergistic role in bioelectrocatalysis for CO₂ reduction is emerging thanks to its outstanding selectivity, high faradic efficiency, and desirable valuable C_n products under mild condition that are surveyed in this review. Herein, we comprehensively discuss the results already obtained for the integration craft of enzymatic-electrocatalysis and microbial-electrocatalysis technologies. In addition, the intrinsic nature of the combination is highly dependent on the electron transfer. Thus, both direct electron transfer and mediated electron transfer routes are modeled and concluded. We also explore the biocompatibility and synergistic effects of electrode materials, which emerge in combination with tuned enzymes and microbes to improve catalytic performance. The system by integrating solar energy driven photo-electrochemical technics with bio-catalysis is further discussed. We finally highlight the significant findings and perspectives that have provided strong foundations for the remarkable development of green and sustainable bioelectrocatalysis for CO₂ reduction, and that offer a blueprint for C_n valuable products originate from CO₂ under efficient and mild conditions.

Probing the robustness of Geobacter sulfurreducens against fermentation hydrolysate for uses in bioelectrochemical systems

In this study, impacts of toxic ions/acids found in real fermentation-hydrolysate on the model exoelectrogenic G. sulfurreducens were investigated. Initially, different concentrations of acetate, butyrate, propionate, Na⁺, and K⁺ were tested, individually and in combination, for effects on the planktonic growth, followed by validation with diluted-hydrolysate. Meanwhile, it could be shown that (1) excess Na⁺ (≥100 mM) causes inhibition that can be reduced by K⁺ replacement, (2) butyrate (≥10 mM) induces higher toxicity than propionate, and (3) hydrolysate induces synergistic inhibition to G. sulfurreducens where organic constituents contributed more than Na⁺. Afterwards, compared with impacts on planktonic cells, the pre-enriched anodic biofilm of G. sulfurreducens in BESs showed higher robustness against diluted-hydrolysate, achieving current densities of 1.4-1.7 A/m² (at up to ∼30 mM butyrate and propionate as well as ∼240 mM Na⁺). As a conclusion, using G. sulfurreducens in BESs dealing with fermentation-hydrolysate can be regulated for efficacious energy recovery.

Microbial fuel cell: A green eco-friendly agent for tannery wastewater treatment and simultaneous bioelectricity/power generation

This review paper emphasised on the origin of hexavalent chromium toxicity in tannery wastewater and its remediation using novel Microbial Fuel Cell (MFC) technology, including electroactive bacteria, which are known as exoelectrogens, to simultaneously treat wastewater and its action in the production of bioenergy and the mechanism of Cr⁶⁺ reduction. Also, there are various parameters like electrode, pH, mode of operation, time of operation, and type of exchange membrane used for promising results shown in enhancing MFC production and remediation of Cr⁶⁺. Destructive anthropological activities, such as leather making and electroplating industries are key sources of hexavalent chromium contamination in aquatic repositories. When Cr⁶⁺ enters the food chain and enters the human body, it has the potential to cause cancer. MFC is a green innovation that generates energy economically through the reduction of toxic Cr⁶⁺ to less toxic Cr³⁺. The organic substrates utilized at the anode of MFC act as electrons (e^-) donors. This review also highlighted the utilization of cheap substrates to make MFCs more economically suitable and the energy production at minimum cost.

Employing conductive carrier for establishing spontaneous microbial galvanic cell and accelerating denitrification

It is well-known that metal corrosion is accelerated by formation of galvanic cell. In this study, we reported the acceleration of denitrification by using conductive carrier through formation of microbial galvanic cell (MGC). Electrically conductive graphite plate (GP) was used as biofilm carrier and compared with the non-conductive polypropylene (PP) plate carrier. Cyclic voltametric analyses showed that biofilms with bidirectional electron transfer functions of bioelectrochemical denitrification (BEDN) and acetate oxidation could be enriched spontaneously onto the GP carrier, hinting the establishment of MGC. Further analysis using differential pulse voltammetry revealed that the redox mediator related to extracellular electron transfer was detected in both media of the GP and PP carrier. Microbial community analysis showed that the biofilms in both GP and PP carrier had identical microbial composition but varied in abundance. The genus of Comamonas, Pseudomonas, Paracoccus and Thauera were the dominance of electroactive denitrifiers responsible for BEDN in both the GP and PP carrier. The GP carrier had a 75.9% higher abundant enrichment of electroactive denitrifiers than the PP carrier. Denitrification performance analyses showed that the GP carrier had a denitrification rate constant (k_DN) of 1.25 and 2.66 h^-1 at 15 °C and 30 °C, respectively, which was nearly 76.1% and 92.7% higher than the non-conductive PP carrier with corresponding values of about 0.71 and 1.38 h^-1. Further, the result of conductive carrier accelerating denitrification was confirmed in scaled-up denitrification bioreactors with volume of 104 L using brush-like biofilm carriers. The acceleration of denitrification was attributed to the spontaneously established MGC, which promoted the direct and mediated electron transfer of the electroactive denitrifiers grown onto the conductive carriers and speeded up the BEDN. The result of this study demonstrated that the BEDN could be integrated to traditional biological denitrification system to accelerate denitrification in the form of MGC by simply employment of conductive carrier.

The effect of anode potential on electrogenesis, methanogenesis and sulfidogenesis in a simulated sewer condition

Methane emissions from the sewer system are considered to be a non-negligible source of aggravating the greenhouse effect. Meanwhile, the sewer system has long been plagued by sulfide-induced corrosion problems. This study explored the possibility of using a bioelectrochemical system to intensify the competition between electroactive bacteria, methanogens and sulfate-reducing bacteria, thereby reducing the production of methane and sulfide. Dual-chamber bioelectrochemical reactors were constructed and operated in fed-batch mode with the coexistence of Electroactive bacteria, Methanogenic archaea and Sulfate-reducing bacteria. Acetate was supplied as the sole carbon source. The results indicated that electrogenesis induced by the anode potentials of -0.42 V and -0.2 V (vs. Ag/AgCl) had advantages over methanogenesis and sulfidogenesis in consuming acetate. The stimulated electrogenesis by anode potentials resulted in a decrease in pH. Methane production was suppressed in the reactors with anode potentials of -0.42 and -0.2 V compared to open circuit controls. In contrast to methane, the capacity for sulfide production was facilitated in the reactors with the anode potentials of -0.42 V and -0.2 V compared to open circuit controls. 16s rRNA gene analysis showed that Geobacter was the most abundant genus on the anode biofilm in the anode potential-controlled reactor, while acetoclastic methanogens dominated in open circuit controls. Methanosaeta and Methanosarcina were the most abundant methanogens in open circuit controls. Collectively, our study demonstrates that the use of electrodes with anode potential control can help to control methane emissions, but could not yet prevent sulfide production, which requires further research.

Bio-Electrochemical Performance of a Ceramic Microbial Fuel Cell Treating Kitchen Waste Leachate: Effect of Organic Loading Rate and Anode Electrode Surface Area

Performance evaluation of a ceramic microbial fuel cell (CMFC) by varying organic strength, hydraulic retention time (HRT) and anode electrode surface area (AESA) to treat leachate generated from acidogenesis of kitchen waste (KW) was studied by the central composite design of experiment. The increase in organic loading rate (OLR) positively affected power density (PD) while negatively influencing organic removal and coulombic efficiency (CE). This behavior is possible due to substrate inhibition and the coercive effect of low HRT, i.e., substrate washout, biofilm abrasion, and reduced contact period, while at high HRT, the volatile fatty acid (VFA) degradation improved. Since acetic acid is the final product of long-chain VFAs degradation, a pseudo consumption order for VFAs was obtained: butyric > propionic > acetic. The AESA aided organics removal and PD but had a negligible effect on CE. According to ANOVA, the COD removal was linearly modeled, while PD and CE were quadratic. The validation runs (VR) proved efficient as the highest COD removal was for VR2 (83.7 ± 3.6%), while maximum PD and CE values obtained were 0.224 ± 0.02 W/m3 and 2.62 ± 0.33%, respectively, for VR3, supported by the lower anode potential.

Investigating the interaction between Shewanella oneidensis and phenazine 1-carboxylic acid in the microbial electrochemical processes

Many exoelectrogens utilize small redox mediators for extracellular electron transfer (EET). Notable examples include Shewanella species, which synthesize flavins, and Pseudomonas species, which produce phenazines. In natural and engineered environments, redox-active metabolites from different organisms coexist. The interaction between Shewanella oneidensis and phenazine 1-carboxylic acid (PCA, a representative phenazine compound) was investigated to demonstrate exoelectrogens utilizing metabolites secreted by other organisms as redox mediators. After 24 h in a reactor with and without added PCA (1 μM), the anodic current generated by Shewanella was 235 ± 11 and 51.7 ± 2.8 μA, respectively. Shewanella produced oxidative current approximately three times as high with medium containing PCA as with medium containing the same concentration of riboflavin. PCA also stimulated inward EET in Shewanella. The strong effect of PCA on EET was attributed to its enrichment at the biofilm/electrode interface. The PCA voltammetric peak heights with a Shewanella bioanode were 25-30 times higher than under abiotic conditions. The electrochemical properties of PCA were also altered by the transition from two-electron to single-electron electrochemistry, which suggests PCA was bound between the electrode and cell surface redox proteins. This behavior would benefit electroactive bacteria, which usually dwell in open systems where mediators are present in low concentrations. Like flavins, PCA can be immobilized under both bioanode and biocathode conditions but not under metabolically inactive conditions. Shewanella rapidly transfers electrons to PCA via its Mtr pathway. Compared with wild-type Shewanella, the PCA reduction ability was decreased in gene knockout mutants lacking Mtr pathway cytochromes, especially in the mutants with severely undermined electrode-reduction capacities. These strains also lost the ability to immobilize PCA, even under current-generating conditions.

Bioelectrochemical systems-based metal removal and recovery from wastewater and polluted soil: Key factors, development, and perspective

Bioelectrochemical systems (BES) are considered efficient and sustainable technologies for bioenergy generation and simultaneously removal/recovery metal (loid)s from soil and wastewater. However, several current challenges of BES-based metal removal and recovery, especially concentrating target metals from complex contaminated wastewater or soil and their economic feasibility of engineering applications. This review summarized the applications of BES-based metal removal and recovery systems from wastewater and contaminated soil and evaluated their performances on electricity generation and metal removal/recovery efficiency. In addition, an in depth review of several key parameters (BES configurations, electrodes, catalysts, metal concentration, pH value, substrate categories, etc.) of BES-based metal removal and recovery was carried out to facilitate a deep understanding of their development and to suggest strategies for scaling up their specific application fields. Finally, the future intervention on multifunctional BES to improve their performances of mental removal and recovery were revealed.

Microbiomics for enhancing electron transfer in an electrochemical system

In microbial electrochemical systems, microorganisms catalyze chemical reactions converting chemical energy present in organic and inorganic molecules into electrical energy. The concept of microbial electrochemistry has been gaining tremendous attention for the past two decades, mainly due to its numerous applications. This technology offers a wide range of applications in areas such as the environment, industries, and sensors. The biocatalysts governing the reactions could be cell secretion, cell component, or a whole cell. The electroactive bacteria can interact with insoluble materials such as electrodes for exchanging electrons through colonization and biofilm formation. Though biofilm formation is one of the major modes for extracellular electron transfer with the electrode, there are other few mechanisms through which the process can occur. Apart from biofilm formation electron exchange can take place through flavins, cytochromes, cell surface appendages, and other metabolites. The present article targets the various mechanisms of electron exchange for microbiome-induced electron transfer activity, proteins, and secretory molecules involved in the electron transfer. This review also focuses on various proteomics and genetics strategies implemented and developed to enhance the exo-electron transfer process in electroactive bacteria. Recent progress and reports on synthetic biology and genetic engineering in exploring the direct and indirect electron transfer phenomenon have also been emphasized.

The integration of bio-catalysis and electrocatalysis to produce fuels and chemicals from carbon dioxide

The dependence on fossil fuels has caused excessive emissions of greenhouse gases (GHGs), leading to climate changes and global warming. Even though the expansion of electricity generation will enable a wider use of electric vehicles, biotechnology represents an attractive route for producing high-density liquid transportation fuels that can reduce GHG emissions from jets, long-haul trucks and ships. Furthermore, to achieve immediate alleviation of the current environmental situation, besides reducing carbon footprint it is urgent to develop technologies that transform atmospheric CO₂ into fossil fuel replacements. The integration of bio-catalysis and electrocatalysis (bio-electrocatalysis) provides such a promising avenue to convert CO₂ into fuels and chemicals with high-chain lengths. Following an overview of different mechanisms that can be used for CO₂ fixation, we will discuss crucial factors for electrocatalysis with a special highlight on the improvement of electron-transfer kinetics, multi-dimensional electrocatalysts and their hybrids, electrolyser configurations, and the integration of electrocatalysis and bio-catalysis. Finally, we prospect key advantages and challenges of bio-electrocatalysis, and end with a discussion of future research directions.

3D Conducting Polymeric Membrane and Scaffold Saccharomyces cerevisiae Biofilms to Enhance Energy Conversion in Microbial Fuel Cells

Microbial fuel cells (MFCs) can spontaneously convert chemical energy into electricity using biocatalytic microorganisms and organic matter as fuel feedstocks. Three-dimensional cross-linked poly(vinyl alcohol)-based membranes were produced by a sol-gel method under homogeneous catalysis and used as the electrolyte to facilitate effective proton conduction. Under dry conditions, these polymeric membranes showed high water uptake (120%) and ionic conductivity (2.815 mS cm^-1). In the anode compartment, the scaffold Saccharomyces cerevisiae film biocatalysts were used to improve electron transfer to the cathode, using three major configurations to generate a higher power output. It was found that the graphene anchoring, red light (RL) stimulation, and methylene blue (MB) mediation-enhanced device performance. The electrochemically derived graphene improved the power and current density by 40% because of its high conductivity. The RL stimulation increased the power density by 80% because of a shortened electron flow path to complex III. The MB mediation also yielded a higher current density by 340% because MB can bypass the electron flow from complex II to cytochrome c and transfer electrons directly to complex III. The individual and collective increase in power output was due to more efficient electron flow from the electronic network permeating the biofilm. The generated electrons were transferred either to graphene as an energy-efficient direct transfer mode or to methylene blue as a long-range redox mediator for indirect transfer. Red light stimulation enhanced oxygen utilization efficiency and stimulated electrons in redox proteins enhancing electron flux. These processes generated higher power through the more efficient generation of electrons and faster transport to the external circuit. As society migrates from gasoline consumption to low carbon-based fuels, the MFCs become important in producing electrical energy with low net emissions.

Genome analysis of Pseudomonas chlororaphis subsp. aurantiaca mutant strains with increased production of phenazines

Genomes of three strains-phenazine producers-Pseudomonas chlororaphis subsp. aurantiaca (B-162 (wild type), mutant strain B-162/255, and its derivative B-162/17) were sequenced and compared. Comparison of a wild-type strain and B-162/255 mutant genomes revealed 32 mutations. 19 new mutations were detected in the genome of B-162/17. Further bioinformatics analysis allowed us to predict mutant protein functions and secondary structures of five gene products, mutations which might potentially influence phenazine synthesis and secretion in Pseudomonas bacteria. These genes encode phenylalanine hydroxylase transcriptional activator PhhR, type I secretion system permease/ATPase, transcriptional regulator MvaT, GacA response regulator, and histidine kinase. Amino acid substitutions were found in domains of studied proteins. One deletion in an intergenic region could affect a potential transcription factor binding site that participates in the regulation of gene that encodes ABC transporter.

Extracellular Electron Transfer by Pseudomonas aeruginosa in Biocorrosion: A Review

Microorganisms with extracellular electron transfer (EET) capability have gained significant attention for their different biotechnological applications, like biosensors, bioremediation, and microbial fuel cells. Current research affirmed that microbial EET potentially promotes corrosion of iron structures, termed microbiologically influenced corrosion (MIC). The sulfate-reducing (SRB) and nitrate-reducing (NRB) bacteria are the most investigated among the different MIC-promoting bacteria. Unlike extensively studied SRB corrosion, NRB corrosion has received less attention from researchers. Hence, this review focuses on EET by Pseudomonas aeruginosa, a pervasive bacterium competent for developing biofilms in marine habitats and oil pipelines. A comprehensive discussion on the fundamentals of EET mechanisms in MIC is provided first. After that, the review offers state-of-the-art insights into the latest research on the EET-assisted MIC by Pseudomonas aeruginosa. The role of electron transfer mediators has also been discussed to understand the mechanisms involved in a better way. This review will be beneficial to open up new opportunities for developing strategies for combating biocorrosion.

Synchronous Cr(VI) Remediation and Energy Production Using Microbial Fuel Cell from a Subsurface Environment: A Review

Applying microbial fuel cell (MFC) technology for eco-remediation of Cr(VI) pollution from a subsurface environment has great scientific value and practical significance due to its promising advantages of pollutant remediation and renewable energy generation. The aim of the current review is to summarize the migration characteristics of Cr(VI) in a subsurface soil/water environment and investigate the factors affecting the MFC performance for synchronous Cr(VI) remediation and power generation, and sequentially highlight diverse challenges of MFC technology for in situ remediation of subsurface groundwater and soils. The critical review put forward that Cr(VI) removal efficiency and energy production of MFC can be improved by enhancing the adjustability of cathode pH, setting potential, modifying electrode, and incorporating other technologies into MFC. It was recommended that designing typical large-scale, long-term continuous flow MFC systems, adding electron shuttle media or constructing artificial electron according to actual groundwater/soil and Cr(VI) pollution characteristics, site geology, and the hydrogeology condition (hydrochemical conditions, colloid type, and medium) are essential to overcome the limitations of the small size of the laboratory experiments and improve the application of technology to in situ Cr(VI) remediation. This review provided reference and ideas for future research of MFC-mediated onsite Cr(VI) remediation.

A high-sensitive and durable electrochemical sensor based on Geobacter-dominated biofilms for heavy metal toxicity detection

A highly sensitive electrochemical sensor for detecting low concentrations of heavy metals (Cd²⁺, Ni²⁺, Pb²⁺ and Cu²⁺) based on Geobacter-dominated biofilms was developed. The biosensor showed a high sensitivity for the determination of Cd²⁺ (109.7 μAμM^-1cm^-2) and the determination of Pb²⁺ (161.7 μAμM^-1cm^-2). The performance of three fitting models for biosensor response to heavy metal toxicity was investigated based on the relationship between total coulomb yield and heavy metal concentration. The full-area model (Equation a) provided the best fit, and the response times tended to be the fastest based on the peak current model (Equation c). Recovery methods were proposed to ensure the electrical activity of the biofilm for long-term monitoring. 16S rRNA gene sequence analysis showed that the most dominant genus in the anodic biofilm was Geobacter (44.1%-45.8%), indicating a stable community structure after continuous toxicity shock for 22 days. The confocal laser scanning microscope (CLSM) further proved the restorable and reusability of the biosensor. Thanks to the thin and electrically active Geobacter-dominated biofilms, it could be a good alternative biosensor for groundwater analysis etc. The results of this study contribute to the development of a highly sensitive and accurate biosensor with long-term usage towards on-site monitoring of heavy metals at low concentrations, improving the test performance of the biosensor for practical application.

Bio-electrochemical frameworks governing microbial fuel cell performance: technical bottlenecks and proposed solutions

Microbial fuel cells (MFCs) are recognized as a future technology with a unique ability to exploit metabolic activities of living microorganisms for simultaneous conversion of chemical energy into electrical energy. This technology holds the promise to offer sustained innovations and continuous development towards many different applications and value-added production that extends beyond electricity generation, such as water desalination, wastewater treatment, heavy metal removal, bio-hydrogen production, volatile fatty acid production and biosensors. Despite these advantages, MFCs still face technical challenges in terms of low power and current density, limiting their use to powering only small-scale devices. Description of some of these challenges and their proposed solutions is demanded if MFCs are applied on a large or commercial scale. On the other hand, the slow oxygen reduction process (ORR) in the cathodic compartment is a major roadblock in the commercialization of fuel cells for energy conversion. Thus, the scope of this review article addresses the main technical challenges of MFC operation and provides different practical approaches based on different attempts reported over the years.

Sustainable operation requires addressing key MFC-bottleneck issues. Enhancing extracellular electron transfer is the key to elevated MFC performance.

An integrated anaerobic digestion and microbial electrolysis system for the enhancement of methane production from organic waste: Fundamentals, innovative design and scale-up deliberation

In the foreseeable future, renewable energy generation from electromethanogenesis to be more cost-effective energy. Electromethanogenesis system is a recent and efficient CO₂ to methane technology to upgrade biogas to 100% methane for power generation. And this can be attained through by integrating anaerobic digestion with microbial electrolysis system. Microbial electrolysis system can able to support carbon reduction on cathode and oxidation on anode by CO₂ capture thereby provides more CH₄ production from an integrated anaerobic digestion system. Scale-up the recent advance technique of microbial electrolysis system in the anaerobic digestion process for 100% methane production for power generation is need of the hour. The overall objective of this review is to facilitate the recent technology of microbial electrolysis system in the anaerobic digestion process. At first, the function of electromethanogenesis system and innovative integrated design method are outlined. Secondly, different external parameters such as applied voltage, operating temperature, pH etc are examined for the significance on process optimization. Eventually, electrode selections, electrode spacing, surface chemistry and surface area are critically reviewed for the scale-up considerations of integration process.

Recent advancements in microbial fuel cells: A review on its electron transfer mechanisms, microbial community, types of substrates and design for bio-electrochemical treatment

The development in urbanization, growth in industrialization and deficiency in crude oil wealth has made to focus more for the renewable and also sustainable spotless energy resources. In the past two decades, the concepts of microbial fuel cell have caught more considerations among the scientific societies for the probability of converting, organic waste materials into bio-energy using microorganisms catalyzed anode, and enzymatic/microbial/abiotic/biotic cathode electro-chemical reactions. The added benefit with MFCs technology for waste water treatment is numerous bio-centered processes are available such as sulfate removal, denitrification, nitrification, removal of chemical oxygen demand and biological oxygen demand and heavy metals removal can be performed in the same MFC designed systems. The various factors intricate in MFC concepts in the direction of bioenergy production consists of maximum coulombic efficiency, power density and also the rate of removal of chemical oxygen demand which calculates the efficacy of the MFC unit. Even though the efficacy of MFCs in bioenergy production was initially quietly low, therefore to overcome these issues few modifications are incorporated in design and components of the MFC units, thereby functioning of the MFC unit have improvised the rate of bioenergy production to a substantial level by this means empowering application of MFC technology in numerous sectors including carbon capture, bio-hydrogen production, bioremediation, biosensors, desalination, and wastewater treatment. The present article reviews about the microbial community, types of substrates and information about the several designs of MFCs in an endeavor to get the better of practical difficulties of the MFC technology.

Optimization of microbial fuel cell process using a novel consortium for aromatic hydrocarbon bioremediation and bioelectricity generation

Microbial Fuel Cell (MFC) is an innovative bio-electrochemical approach which converts biochemical energy inherent in wastewater into electrical energy, thus contributing to circular economy. Five electrogenic bacteria, Kocuria rosea (GTPAS76), two strains of Bacillus circulans (GTPO28 and GTPAS54), and two strains of Corynebacterium vitaeruminis (GTPO38 and GTPO42) were isolated from a common effluent treatment plant (CETP) and were used individually as well as in consortium form to run double chambered "H" type microbial fuel cell. Individually they could produce voltage in the range of 0.4-0.7 V in the MFC systems. Consortium developed using GTPO28, GTPO38, GTPAS54 and GTPAS76 were capable of producing voltage output of 0.8 V with 81.81 % and 64 % COD and BOD reduction, respectively. The EPS production capacity and electricity generation by the isolated bacteria correlated significantly (r = 0.72). Various parameters like, effect of preformed biofilm, length of salt bridge and its reuse, aeration, substrate concentration and external resistance were studied in detail. The study emphasizes on improving the commercialization aspect of MFC with repeated use of salt bridge and improving wastewater treatment potential after optimization of MFC system. Polarization curve and power density trends were studied in optimized MFC. A maximum power density and current density achieved were 18.15 mW/m² and 370.37 mA/m², respectively using 5 mM sodium benzoate. This study reports the use of sodium benzoate as a substrate along with reusing of the salt bridge in MFC study with promising results for BOD and COD reduction, proving it to be futuristic technology for bio-based circular ecosystem development.

Management of Cattle Dung and Novel Bioelectricity Generation Using Microbial Fuel Cells: An Ingenious Experimental Approach

Microbial fuel cells (MFCs) are the rising modern equipment for the generation of bioelectricity from organic matters. In this study, MFCs in two formats are assembled and concurrently operated for a 30-day period in a batch mode manner. Natural biowaste cattle dung slurry with mediators is used as a substrate persistently for the enhancement of electron transfer rate and additionally for the augmentation of required electrical parameters. Under similar conditions, the MFC setups are experimented with a variety of anode-cathode material combinations, namely carbon-carbon, copper-carbon, and zinc-carbon. The performance of these MFCs during the testing period is evaluated independently and compared by plotting polarization data generated by them. It is revealed that maximum current and power densities are achieved from all these MFCs and the best attained values are 1858 mA/m2 and 1465 mW/m2, respectively, for the novel single-chamber zinc-carbon electrode MFC. The corresponding findings present that the MFC with zinc-carbon electrodes has the better power density than other MFCs. Being conductive and higher standard potential metal electrodes have improved the capability to act in place of carbon family electrodes for MFC-based power applications. Although the MFC power generation is low, but modifications in configurations, electrodes, microbe-rich biowaste, mediators, and power management may enhance the power output to a significant level for commercialization of this technology. The unique feature of this research is to explore the pertinent use of conductive metal electrodes to enhance the power generation capability of MFCs through biowaste as an alternative power source for small applications. The novelty of this research is presented through usage of conductive metal electrodes for the performance analysis of MFCs.

Performance of Yeast Microbial Fuel Cell Integrated with Sugarcane Bagasse Fermentation for COD Reduction and Electricity Generation

The purpose of this analysis is to evaluate the efficiency of the Microbial Fuel Cell (MFC) system incorporated with the fermentation process, with the aim of reducing COD and generating electricity, using sugarcane bagasse extract as a substrate, in the presence and absence of sugarcane fibers. There is a possibility of turning bagasse extract into renewable bioenergy to promote the sustainability of the environment and energy. As a result, the integration of liquid fermentation (LF) with MFC has improved efficiency compared to semi-solid state fermentation (S-SSF). The maximum power generated was 14.88 mW/m2, with an average COD removal of 39.68% per cycle. The variation margin of the liquid fermentation pH readings remained slightly decrease, with a slight deflection of +0.14 occurring from 4.33. With the absence of bagasse fibers, biofilm can grow freely on the anode surface so that the transfer of electrons is fast and produces a relatively high current. Experimental data showed a positive potential after an effective integration of the LF and MFC systems in the handling of waste. The product is then simultaneously converted into electrical energy. Copyright © 2021 by Authors, Published by BCREC Group. This is an open access article under the CC BY-SA License (https://creativecommons.org/licenses/by-sa/4.0). 

The Implications of Membranes Used as Separators in Microbial Fuel Cells

Microbial fuel cells (MFCs) are electrochemical devices focused on bioenergy generation and organic matter removal carried out by microorganisms under anoxic environments. In these types of systems, the anodic oxidation reaction is catalyzed by anaerobic microorganisms, while the cathodic reduction reaction can be carried out biotically or abiotically. Membranes as separators in MFCs are the primary requirements for optimal electrochemical and microbiological performance. MFC configuration and operation are similar to those of proton-exchange membrane fuel cells (PEMFCs)-both having at least one anode and one cathode split by a membrane or separator. The Nafion® 117 (NF-117) membrane, made from perfluorosulfonic acid, is a membrane used as a separator in PEMFCs. By analogy of the operation between electrochemical systems and MFCs, NF-117 membranes have been widely used as separators in MFCs. The main disadvantage of this type of membrane is its high cost; membranes in MFCs can represent up to 60% of the MFC's total cost. This is one of the challenges in scaling up MFCs: finding alternative membranes or separators with low cost and good electrochemical characteristics. The aim of this work is to critically review state-of-the-art membranes and separators used in MFCs. The scope of this review includes: (i) membrane functions in MFCs, (ii) most-used membranes, (iii) membrane cost and efficiency, and (iv) membrane-less MFCs. Currently, there are at least 20 different membranes or separators proposed and evaluated for MFCs, from basic salt bridges to advanced synthetic polymer-based membranes, including ceramic and unconventional separator materials. Studies focusing on either low cost or the use of natural polymers for proton-exchange membranes (PEM) are still scarce. Alternatively, in some works, MFCs have been operated without membranes; however, significant decrements in Coulombic efficiency were found. As the type of membrane affects the performance and total cost of MFCs, it is recommended that research efforts are increased in order to develop new, more economic membranes that exhibit favorable properties and allow for satisfactory cell performance at the same time. The current state of the art of membranes for MFCs addressed in this review will undoubtedly serve as a key insight for future research related to this topic.

Using structure-function relationships to understand the mechanism of phenazine-mediated extracellular electron transfer in Escherichia coli

Phenazines are redox-active nitrogen-containing heterocyclic compounds that can be produced by either bacteria or synthetic approaches. As an electron shuttles (mediators), phenazines are involved in several biological processes facilitating extracellular electron transfer (EET). Therefore, it is of great importance to understand the structural and electronic properties of phenazines that promote EET in microbial electrochemical systems. Our previous study experimentally investigated a phenazine-based library as an exogenous mediator system to facilitate EET in Escherichia coli. Herein, we combine our experimental data with density functional theory (DFT) calculations and multivariate linear regression modeling to understand the structure-function relationships in phenazine-based mediated EET. These calculations demonstrate that the computed redox properties of phenazines in lipophilic environments (e.g., cell membrane) correlate to experimental mediated current densities. Additional DFT-derived molecular properties were considered to develop a predictive model, which could be used in metabolic engineering approaches to introduce phenazines as endogenous mediators into bacteria.

Emerging technologies for conversion of sustainable algal biomass into value-added products: A state-of-the-art review

Concerns regarding high energy demand and gradual depletion of fossil fuels have attracted the desire of seeking renewable and sustainable alternatives. Similar to but better than the first- and second-generation biomass, algae derived third-generation biorefinery aims to generate value-added products by microbial cell factories and has a great potential due to its abundant, carbohydrate-rich and lignin-lacking properties. However, it is crucial to establish an efficient process with higher competitiveness over the current petroleum industry to effectively utilize algal resources. In this review, we summarize the recent technological advances in maximizing the bioavailability of different algal resources. Following an overview of approaches to enhancing the hydrolytic efficiency, we review prominent opportunities involved in microbial conversion into various value-added products including alcohols, organic acids, biogas and other potential industrial products, and also provide key challenges and trends for future insights into developing biorefineries of marine biomass.

Investigating the response of electrogenic metabolism to salinity in saline wastewater treatment for optimal energy output via microbial fuel cells

In the current study, MFCs treating saline wastewater with the different conductivities of 5.0 ± 0.2, 7.7 ± 0.6, 10.5 ± 0.9, 13.0 ± 1.0, 15.3 ± 1.0, and 16.0 ± 0.1 mS/cm were investigated. Increasing salinity drives a considerable shift of microbial communities, and it also affects metabolic pathways in MFCs. Overwhelming acetate oxidizing electron transfer with moderate conductivities between 7.7 and 13.0 mS/cm led to high energy outputs. Power generation at the low conductivities of less than 7.7 mS/cm was restricted by the competition between fermentative bacteria (e.g., Lactobacillus) and exoelectrogens (e.g., Pseudomonas and Shewanella) for substrate utilization. Increasing salinity beyond 13 mS/cm suppressed the fermentation of glucose to butyrate. It also induced sulfidogenesis; sulfide oxidizing bacteria Desulfovibrio (5.2%), Desulfuromonas (3.7%) and exoelectrogen Pseudomonas (1.1%) formed a sulfur-driven current production, thereby resulting in low energy outputs. The present study revealed the effects of ionic conductivity on electrical energy production and provided insights into the dynamics of the MFCs substrate utilization.

Tuning of Electrode Surface for Enhanced Bacterial Adhesion and Reactions: A Review on Recent Approaches

The study of bacterial adhesion and its consequences has great significance in different fields such as marine science, renewable energy sectors, soil and plant ecology, food industry, and the biomedical field. Generally, the adverse effects of microbial surface interactions have attained wide visibility. However, herein, we present distinct approaches to highlight the beneficial aspects of microbial surface interactions for various applications rather than deal with the conventional negative aspects or prevention strategies. The surface microbial reactions can be tuned for useful biochemical or bio-electrochemical applications, which are otherwise unattainable through conventional routes. In this context, the present review is a comprehensive approach to highlight the basic principles and signature parameters that are responsible for the useful microbial-electrode interactions. It also proposes various surface tuning strategies, which are useful for tuning the electrode characteristics particularly suitable for the enhanced bacterial adhesion and reactions. The tuning of surface characteristics of electrodes is discussed with a special reference to the Microbial Fuel Cell as an example.

Bioelectrochemical systems for environmental remediation of estrogens: A review and way forward

Globally estrogenic pollutants are a cause of concern in wastewaters and water bodies because of their high endocrine disrupting activity leading to extremely negative impacts on humans and other organisms even at very low environmental concentrations. Bioremediation of estrogens has been studied extensively and one technology that has emerged with its promising capabilities is Bioelectrochemical Systems (BESs). Several studies in the past have investigated BESs applications for treatment of wastewaters containing toxic recalcitrant pollutants with a primary focus on improvement of performance of these systems for their deployment in real field applications. But the information is scattered and further the improvements are difficult to achieve for standalone BESs. This review critically examines the various existing treatment technologies for the effective estrogen degradation. The major focus of this paper is on the technological advancements for scaling up of these BESs for the real field applications along with their integration with the existing and conventional wastewater treatment systems. A detailed discussion on few selected microbial species having the unusual properties of heterotrophic nitrification and extraordinary stress response ability to toxic compounds and their degradation has been highlighted. Based on the in-depth study and analysis of BESs, microbes and possible benefits of various treatment methods for estrogen removal, we have proposed a sustainable Hybrid BES-centered treatment system for this purpose as a choice for wastewater treatment. We have also identified three pipeline tasks that reflect the vital parts of the life cycle of drugs and integrated treatment unit, as a way forward to foster bioeconomy along with an approach for sustainable wastewater treatment.

Biocatalyst physiology and interplay: a protagonist of MFC operation

Microbial fuel cells (MFC) have been foreseen as a sustainable renewable energy resource to meet future energy demand. In the past, several studies have been executed in both benchtop and pilot scale to produce electrical energy from wastewater. The key role players in this technology that leads to the operation are microbes, mainly bacteria. The dominant among them is termed as "exoelectrogens" that have the capability to produce and transport electron by utilizing waste source. The current review focuses on such electrogenic bacteria's involvement for enhanced power generation of MFC. The pathway of electron transfer in their cell along and its conduction to the extracellular environment of the MFC system are critically discussed. The interaction of the microbes in various MFC operational conditions, including the role of substrate and solid electron acceptors, i.e., anode, external resistance, temperature, and pH, was also discussed in depth along with biotechnological advancement and future research perspective.