An improved method for determining dermal exposure to polycyclic aromatic hydrocarbons

Many workers are occupationally exposed to polycyclic aromatic hydrocarbons (PAHs), which may cause various health problems, and some PAHs are known or suspected carcinogens. PAH exposure is primarily monitored by air sampling, but contamination may also occur through dermal exposure. PAHs adsorbed to the skin can be sampled by tape-stripping, but subsequent extraction of sampling tapes in organic solvent also releases diverse co-eluting substances that are difficult to remove before analysis of the PAHs by gas chromatography/mass spectrometry (GC/MS). The objective of this study was to optimise a procedure for analytical clean-up after extraction of 32 PAHs from tape-strips, by dialysis in organic solvent using semipermeable membranes. With triplicate subsamples, the developed method yields acceptable precision and repeatability for both the 32 PAHs, across the concentration range 10-160 ng per sample, and for a certified reference material (urban dust). The optimized clean-up procedure and GC/MS methodology was used to assess PAHs on skin from the lower part of the ventral side of the wrist and just below the collar bone of three firefighters and seven controls (office workers). Several gaseous and particle-bound PAHs were detected in all samples, including controls. Thus, the optimized procedure using semipermeable membranes for clean-up of tape-strip extracts can be used to assess the dermal exposure of both occupational and general populations to multiple PAHs. The results also show that both gaseous and particle-bound PAHs, including alkylated species, may be present on skin.

Potential Occupational Exposures and Health Risks Associated with Biomass-Based Power Generation

Biomass is increasingly being used for power generation; however, assessment of potential occupational health and safety (OH&S) concerns related to usage of biomass fuels in combustion-based generation remains limited. We reviewed the available literature on known and potential OH&S issues associated with biomass-based fuel usage for electricity generation at the utility scale. We considered three potential exposure scenarios--pre-combustion exposure to material associated with the fuel, exposure to combustion products, and post-combustion exposure to ash and residues. Testing of dust, fungal and bacterial levels at two power stations was also undertaken. Results indicated that dust concentrations within biomass plants can be extremely variable, with peak levels in some areas exceeding occupational exposure limits for wood dust and general inhalable dust. Fungal spore types, identified as common environmental species, were higher than in outdoor air. Our review suggests that pre-combustion risks, including bioaerosols and biogenic organics, should be considered further. Combustion and post-combustion risks appear similar to current fossil-based combustion. In light of limited available information, additional studies at power plants utilizing a variety of technologies and biomass fuels are recommended.

Dermal and inhalation exposure to methylene bisphenyl isocyanate (MDI) in iron foundry workers

Diisocyanates are a group of chemically reactive agents, which are used in the production of coatings, adhesives, polyurethane foams, and parts for the automotive industry and as curing agents for cores in the foundry industry. Dermal and inhalation exposure to methylene bisphenyl isocyanate (MDI) is associated with respiratory sensitization and occupational asthma. However, limited research has been performed on the quantitative evaluation of dermal and inhalation exposure to MDI in occupationally exposed workers. The objective of this research was to quantify dermal and inhalation exposure levels in iron foundry workers. Workers involved in mechanized moulding and mechanized production of cores were monitored: 12 core makers, 2 core-sand preparers, and 5 core installers. Personal breathing-zone levels of MDI were measured using impregnated filter sampling. Dermal exposure to MDI was measured using a tape-strip technique. Three or five consecutive tape-strip samples were collected from five exposed skin areas (right and left forefingers, left and right wrists, and forehead). The average personal air concentration was 0.55 microg m(-3), 50-fold lower than the Swedish occupational exposure limit of 30 microg m(-3). The core makers had an average exposure of 0.77 microg m(-3), which was not significantly different from core installers' and core-sand preparers' average exposure of 0.16 microg m(-3) (P = 0.059). Three core makers had a 10-fold higher inhalation exposure than the other core makers. The core makers' mean dermal exposure at different skin sites varied from 0.13 to 0.34 microg while the two other groups' exposure ranged from 0.006 to 0.062 microg. No significant difference was observed in the MDI levels between the skin sites in a pairwise comparison, except for left forefinger compared to left and right wrist (P < 0.05). In addition, quantifiable but decreasing levels of MDI were observed in the consecutive tape strip per site indicating MDI penetration into the skin. This study indicates that exposure to MDI can be quantified on workers' skin even if air levels are close to unquantifiable. Thus, the potential for uncured MDI to deposit on and penetrate into the skin is demonstrated. Therefore, dermal exposure along with inhalation exposure to MDI should be measured in the occupational settings where MDI is present in order to shed light on their roles in the development of occupational isocyanate asthma.