Gas Digital Microfluidic Platform: Application to Highly Volatile Compound Preconcentration

Digital microfluidics platforms (DMFPs) have shown their efficiency in sample handling, using elementary operations that may be combined to perform complex applications. In this article, we present a new platform for gaseous samples handling involving a two-step digital preconcentration using the miniaturized preconcentrators of the DMFP. Choosing n-pentane at very low concentrations as a model for highly volatile compounds, poorly retained on the sorbent, the DMFP allowed bypassing the limit set by the breakthrough volume by repeating an elementary operation. It enabled a 5-fold increase of preconcentration factors in comparison to a single preconcentration step and an easier monitoring of the model compound. Promising applications are expected, as this system could be adapted to most volatile compound analysis devices, including micro gas chromatographs, to replace the current single-step preconcentration systems. By switching to two-step preconcentration with a DMFP, i.e., a digital preconcentration, it would be possible to get more concentrated samples through the column for easier trace analysis.

Selective Detection of Volatile Organics in a Mixture Using a Photoionization Detector and Thermal Desorption from a Nanoporous Preconcentrator

The selective detection of individual hazardous volatile organic compounds (VOCs) within a mixture is of great importance in industrial contexts due to environmental and health concerns. Achieving this with inexpensive, portable detectors continues to be a significant challenge. Here, a novel thermal separator system coupled with a photoionization detector has been developed, and its ability to selectively detect the VOCs isopropanol and 1-octene from a mixture of the two has been studied. The system includes a nanoporous silica preconcentrator in conjunction with a commercially available photoionization detector (PID). The PID is a broadband total VOC sensor with little selectivity; however, when used in conjunction with our thermal desorption approach, selective VOC detection within a mixture can be achieved. VOCs are adsorbed in the nanoporous silica over a 5 min period at 5 °C before being desorbed by heating at a fixed rate to 70 °C and detected by the PID. Different VOCs desorb at different times/temperatures, and mathematical analysis of the set of PID responses over time enabled the contributions from isopropanol and 1-octene to be separated. The concentrations of each compound individually could be measured in a mixture with limits of detection less than 10 ppb_v and linearity errors less than 1%. Demonstration of a separation of a mixture of chemically similar compounds, benzene and o-xylene, is also provided.

Room-temperature-ionic-liquid coated graphitized carbons for selective preconcentration of polar vapors

Most adsorbent materials used for preconcentrating and thermally desorbing volatile and semi-volatile organic compounds (S/VOCs) in portable or "micro" gas chromatographic (GC/µGC) instruments preferentially capture non-polar or moderately polar compounds relative to more polar compounds. Here, we explore the use of a known trigonal-tripyramidal room-temperature ionic liquid (RTIL) as a surface modifier for the graphitized carbons, Carbopack B (C-B) and Carbopack X (C-X), with the goal of enhancing their capacity and selectivity for polar S/VOCs. Breakthrough tests were performed by challenging tubes packed with ∼2.5 mg of C-B or RTIL-coated C-B (RTIL/C-B) with 13 individual S/VOCs, including several organophosphorus compounds and reference alkyl and aromatic hydrocarbons of comparable vapor pressures, at concentrations ranging from 14 to 130 mg/m³. The 10% breakthrough volume, V_b10, was used as the measure of capacity. For the RTIL/C-B, the V_b10 values of the five organophosphorus vapors tested were consistently ∼2.5 times larger than those for the untreated C-B, and V_b10 values of the four non-polar reference vapors were 11-26 times smaller for the RTIL/C-B than for the untreated C-B. For compounds of similar vapor pressure the capacity ratios for polar vs. non-polar compounds with the RTIL/C-B ranged from 1.8 to 34. Similar results were obtained with C-X and RTIL/C-X on a smaller set of compounds. Tests at 70% relative humidity or with a binary mixture of a polar and non-polar compound had no effect on the capacity of the RTIL/C-B, and there were no changes in V_b10 values after several months of testing that included cycling from 25 to 250 °C. Capacity was strongly correlated with vapor pressure. Attempts to reconcile the selectivity using models based on linear-solvation-energy relationships were only partially successful. Nonetheless, these results indicate that RTIL coating of carbon adsorbents affords a simple, reliable means of rendering them selective for polar S/VOCs.

Improving thermal desorption aerosol gas chromatography using a dual-trap design

Thermal desorption aerosol gas chromatography (TAG) is an effective tool for in situ analysis of particulate organic molecules. However, the performance of current TAG is limited by the detectability of low volatile compounds and the matrix effect. In this study, a dual-trap TAG system was developed to address these issues. Thermally desorbed effluent is focused by a weakly retained trap (for low volatile compounds) in a 1 m capillary column conditioned in the GC oven, followed by a strongly retained trap (for high volatile compounds). Then, the focused analytes are desorbed in a reverse flow into the GC column for analysis. Detection over a wide volatility range from C10 to C40 n-alkanes is achieved using the dual-trap TAG. We show that it has lower discrimination of injection, better linearity and higher detectability of n-alkanes. The dual-trap TAG was applied for in-situ measurement of ambient fine particles (PM_2.5) in Beijing. Repeatable retention time of n-alkanes was demonstrated during a continuous measurement over two weeks.

Trichloroethylene sensing in water based on SERS with multifunctional Au/TiO2 core-shell nanocomposites

Herein we report on a rapid and highly sensitive scheme to detect trichloroethylene (TCE), an environmental contaminant, by surface enhanced Raman scattering (SERS) with multifunctional Au/TiO2 core-shell nanocomposites as SERS substrates. A facile approach to fabricate TiO2 shell around gold core nanocomposites is proposed as sensors for TCE detection by SERS. During detection, TCE was first oxidized due to the photocatalytic activity of the TiO2 shell and the increase in SERS intensity due to the product of TCE photooxidation can be used to determine the concentration of TCE. It should be noted that the SERS of the Raman label, 4-mercaptopyridine (4-MPy) modified onto the gold nanoparticle (GNP) core is in proportion to the product of TCE photooxidation. After optimizing the sample pH, enrichment of the analyte, and the UV exposure time, the methodology developed accomplishes an excellent limit of detection (LOD) (0.038 μM, i.e.∼5 ppb) for TCE in water. Our unique approach based on the synthesized SERS composite to detect TCE, a chlorinated environmental contaminant directly in water could pave the way for the development of a multifunctional nanosensor platform to monitor TCE and the catalytic reactions in a multiplex format.

A purge and trap integrated microGC platform for chemical identification in aqueous samples

The majority of current micro-scale gas chromatography (μGC) systems focus on air sampling to detect volatile organic compounds (VOCs). However, purging the VOCs from a water sample using microsystems is an unchartered territory. Various organic compounds used in everyday life find their way to water bodies. Some of these water organic compounds (WOCs) persist or degrade slowly, threatening not just human existence but also aquatic life. This article reports the first micro-purge extractor (μPE) chip and its integration with a micro-scale gas chromatography (μGC) system for the extraction and analysis of water organic compounds (WOCs) from aqueous samples. The 2 cm × 3 cm μPE chip contains two inlet and outlet ports and an etched cavity sealed with a Pyrex cover. The aqueous sample is introduced from the top inlet port while a pure inert gas is supplied from the side inlet to purge WOCs from the μPE chip. The outlets are assigned for draining water from the chip and for directing purged WOCs to the micro-thermal preconcentrator (μTPC). The trapped compounds are desorbed from the μTPC by resistive heating using the on-chip heater and temperature sensor, are separated by a 2 m long, 80 μm wide, and 250 μm deep polydimethylsiloxane (OV-1) coated μGC separation column, and are identified using a micro-thermal conductivity detector (μTCD) monolithically integrated with the column. Our experiments indicate that the combined system is capable of providing rapid chromatographic separation (<1.5 min) for quaternary WOCs namely toluene, tetrachloroethylene (PCE), chlorobenzene and ethylbenzene with a minimum detection concentration of 500 parts-per-billion (ppb) in aqueous samples. The proposed method is a promising development towards the future realization of a miniaturized system for sensitive, on-site and real-time field analysis of organic contaminants in water.

Through the years with on-a-chip gas chromatography: a review

In recent years, the need for measurement and detection of samples in situ or with very small volume and low concentration (low and sub-parts per billion) is a cause for miniaturizing systems via microelectromechanical system (MEMS) technology. Gas chromatography (GC) is a common technique that is widely used for separating and measuring semi-volatile and volatile compounds. Conventional GCs are bulky and cannot be used for in situ analysis, hence in the past decades many studies have been reported with the aim of designing and developing chip-based GC. The focus of this review is to follow and investigate the development and the achievements in the field of chip-based GC and its components from the beginning up to the present.

Microfabricated gas chromatograph for rapid, trace-level determinations of gas-phase explosive marker compounds

A prototype microfabricated gas chromatograph (μGC) adapted specifically for the rapid determination of selected gas-phase marker compounds of the explosive 2,4,6-trinitrotoluene (TNT) at sub-parts-per-billion (<ppb) concentrations in complex mixtures is described. Si-microfabricated focuser, separation column, and sensor array components are integrated with a high-volume sampler of conventional construction to reduce analysis time and the limit of detection (LOD). The primary markers selected as target analytes were 2,4-dinitrotoluene (2,4-DNT, a persistent impurity of TNT) and 2,3-dimethyl-2,3-dinitrobutane (DMNB, a taggant), along with 2,6-dinitrotoluene (2,6-DNT, a less-prominent TNT impurity), which was also included in numerous tests. Selective preconcentration, on-column focusing, temperature-programmed chromatographic separation, and sensor array detection/recognition facilitated determinations of the primary markers in the presence of 20 (or more) interferences within ∼2 min under laptop control. Estimated LODs of 2.2, 0.48, and 0.86 ng were achieved for DMNB, 2,6-DNT, and 2,4-DNT, respectively, which correspond to 0.30, 0.067, and 0.12 ppb in each 1-L air sample collected.

Improved performance of micro-fabricated preconcentrators using silica nanoparticles as a surface template

A new approach of enhancing the adsorption capability of the widely used polymer adsorbent Tenax TA poly(2,6-diphenylene oxide) through its deposition on a nano-structured template is reported. The modified Tenax TA-coated silica nanoparticles (SNP) are incorporated as an adsorbent bed in silicon based micro-thermal preconcentrator (μTPC) chips with an array of square microposts embedded inside the cavity and sealed with a Pyrex cover. The interior surface of the chip is first modified by depositing SNP using a layer-by-layer self-assembly technique followed by coating with Tenax TA. The adsorption capacity of the SNP-Tenax TA μTPC is enhanced by as much as a factor of three compared to the one coated solely with thin film Tenax TA for the compounds tested. The increased adsorption ability of the Tenax TA is attributed to the higher surface area provided by the underlying porous SNP coating and the pores between SNPs affecting the morphology of deposited Tenax TA film by bringing nano-scale features into the polymer. In addition, the adsorption ability of the SNP coating as a pseudo-selective inorganic adsorption bed for polar compounds was also observed. The modified Tenax TA-coated SNP μTPC is a promising development toward integrated micro-gas chromatography systems.

Microfabricated gas chromatograph for on-site determinations of TCE in indoor air arising from vapor intrusion. 2. Spatial/temporal monitoring

We demonstrate the use of two prototype Si-microfabricated gas chromatographs (μGC) for continuous, short-term measurements of indoor trichloroethylene (TCE) vapor concentrations related to the investigation of TCE vapor intrusion (VI) in two houses. In the first house, with documented TCE VI, temporal variations in TCE air concentrations were monitored continuously for up to 48 h near the primary VI entry location under different levels of induced differential pressure (relative to the subslab). Concentrations ranged from 0.23 to 27 ppb by volume (1.2-150 μg/m(3)), and concentration trends agreed closely with those determined from concurrent reference samples. The sensitivity and temporal resolution of the measurements were sufficiently high to detect transient fluctuations in concentration resulting from short-term changes in variables affecting the extent of VI. Spatial monitoring showed a decreasing TCE concentration gradient with increasing distance from the primary VI entry location. In the second house, with no TCE VI, spatial profiles derived from the μGC prototype data revealed an intentionally hidden source of TCE within a closet, demonstrating the capability for locating non-VI sources. Concentrations measured in this house ranged from 0.51 to 56 ppb (2.7-300 μg/m(3)), in good agreement with reference method values. This first field demonstration of μGC technology for automated, near-real-time, selective VOC monitoring at low- or subppb levels augurs well for its use in short- and long-term on-site analysis of indoor air in support of VI assessments.

Microfabricated gas chromatograph for on-site determination of trichloroethylene in indoor air arising from vapor intrusion. 1. Field evaluation

Results are presented of inaugural field tests of two identical prototype microfabricated gas chromatographs (μGC) adapted for the in situ determination of trichloroethylene (TCE) in indoor air in support of vapor intrusion (VI) investigations. Each μGC prototype has a pretrap and partially selective high-volume sampler of conventional design, a micromachined-Si focuser for injection, dual micromachined-Si columns for separation, and an integrated array of four microscale chemiresistors with functionalized gold nanoparticle interface films for multichannel detection. Scrubbed ambient air is used as the carrier gas. Field-generated calibration curves were linear for injected TCE masses of 26-414 ng (4.8-77 ppb·L; r(2) > 0.98) and the projected single-sensor detection limit was 0.052 ppb for an 8-L air sample collected and analyzed in 20 min. Consistent performance between the prototypes and good medium-term stability were shown. Above the mitigation action level (MAL) of 2.3 ppb for the field-test site, μGC TCE determinations fell within ±25% of those from the reference method for 21 of 26 measurements, in the presence of up to 37 documented background VOCs. Below the MAL, positive biases were consistently observed, which are attributable to background VOCs that were unresolvable chromatographically or by analysis of the sensor-array response patterns. Results demonstrate that this type of μGC instrument could serve the need for routine TCE determinations in VI-related assessment and mitigation efforts.

Rapid, sensitive, and multiplexed on-chip optical sensors for micro-gas chromatography

We developed and characterized a rapid, sensitive and integrated optical vapor sensor array for micro-gas chromatography (μGC) applications. The sensor is based on the Fabry-Pérot (FP) interferometer formed by a micrometre-thin vapor-sensitive polymer layer coated on a silicon wafer. The thickness and the refractive index of the polymer vary in response to the vapor analyte, resulting in a change in the reflected intensity of the laser impinged on the sensor. In our study, four different polymers were coated on four wells pre-etched on a silicon wafer to form a spatially separated sensor array. A CMOS imager was employed to simultaneously monitor the polymers' response, thus enabling multiplexed detection of a vapor analyte passing through the GC column. A sub-second detection time was demonstrated. In addition, a sub-picogram detection limit was achieved, representing orders of magnitude improvement over the on-chip vapor sensors previously reported.

Microfabricated gas chromatograph for the selective determination of trichloroethylene vapor at sub-parts-per-billion concentrations in complex mixtures

A complete field-deployable microfabricated gas chromatograph (μGC) is described, and its adaptation to the analysis of low- and subparts-per-billion (ppb) concentrations of trichloroethylene (TCE) vapors in complex mixtures is demonstrated through laboratory testing. The specific application being addressed concerns the problem of indoor air contamination by TCE vapor intrusion. The μGC prototype employs a microfabricated focuser, dual microfabricated separation columns, and a microsensor array. These are interfaced to a nonmicrofabricated front-end pretrap and high-volume sampler module to reduce analysis time and limits of detection (LOD). Selective preconcentration and focusing are coupled with rapid chromatographic separation and multisensor detection for the determination of TCE in the presence of up to 45 interferences. Autonomous operation is possible via a laptop computer. Preconcentration factors as high as 500 000 are achieved. Sensitivities are constant over the range of captured TCE masses tested (i.e., 9-390 ng), and TCE is measured in a test atmosphere at 120 parts-per-trillion (ppt), with a projected LOD of 40 ppt (4.2 ng captured, 20 L sample) and a maximum sampling + analytical cycle time of 36 min. Short- and medium-term (1 month) variations in retention time, absolute responses, and response patterns are within acceptable limits.