A three-layer PMMA electrophoresis microchip with Pt microelectrodes insulated by a thin film for contactless conductivity detection

Rapid Detection of AGs using Microchip Capillary Electrophoresis Contactless Conductivity Detection

Background:

In order to realize current aminoglycosides supervision in food and environment, our team improved the sensitivity and separation efficiency of the portable ITO detector, based on the technology of microchip capillary electrophoresis and contactless conductivity detection.

Experiment:

Parameters (the separation voltage, buffer concentration, electrodes gap, elicitation frequency, elicitation voltage) were optimized for the detection of three aminoglycosides, gentamicin, kanamycin and streptomycin and the separation of their mixture in background electrolyte consists of 2-(N-Morpholino) ethanesulfonic acid (MES) and L-Histidine (His). The enhanced method was also applied to other types of aminoglycosides.

Results:

Under optimal conditions, the monitoring of three types of aminoglycosides obtained such a sensitive response that the limits of detection of gentamicin sulfate, kanamycin sulfate and streptomycin sulfate were calculated as 3.1 µg/ml, 0.89 µg/ml and 0.96 µg/ml, at signal-to-noise ratio 3, respectively. In addition they got separated completely from each other only in 40 s. The results of other varieties of aminoglycosides including tobramycin sulfate and amikacin sulfate also met the standard.

Conclusion:

We successfully proposed here an unprecedentedly portable, miniaturized and rapid microchip capillary electrophoresis contactless conductivity detection system to realize current aminoglycosides supervision in food and environment.

Biochemical sensing by nanofluidic crystal in a confined space

Electrokinetics at nanoscale has attracted broad attention as a promising conductivity based biochemical sensing principle with a good selectivity. The nanoparticle crystal, formed by self-assembling nanoparticles inside a microstructure, has been utilized to fulfill a nanoscale electrokinetics based biochemical sensing platform, named nanofluidic crystal in our previous works. This paper introduces a novel nanofluidic crystal scheme by packing nanoparticles inside a well-designed confined space to improve the device-to-device readout consistency. A pair of electrodes was patterned at the bottom of this tunnel-shaped confined space for ionic current recording. The readout from different chips (n = 16) varied within 8.4% under the same conditions, which guaranteed a self-calibration-free biochemical sensing. Biotin and Pb(2+) were successfully detected by using nanofluidic crystal devices packed with streptavidin and DNAzyme modified nanoparticles, respectively. The limits of detection (LODs) were both 1 nM. This electrically readable nanofluidic crystal sensing approach may find applications in low cost and fast disease screening in limited resource environments.

Photoelectrocatalytic microfluidic reactors utilizing hierarchical TiO2 nanotubes for determination of chemical oxygen demand

A novel and highly sensitive microfluidic device which integrated hierarchical TiO₂ nanotubes exhibited an improved detection efficiency for determination of COD.

A real time affinity biosensor on an insulated polymer using electric impedance spectroscopy in dielectric microchips

This paper demonstrates how a contactless microelectrode allows monitoring of the electric impedance changes provoked by the association of two protein ligands.

In-plane alloy electrodes for capacitively coupled contactless conductivity detection in poly(methylmethacrylate) electrophoretic chips

A simple method for producing PMMA electrophoresis microchips with in-plane electrodes for capacitively coupled contactless conductivity detection is presented. One PMMA plate (channel plate) is embossed with the microfluidic and electrode channels and lamination bonded to a blank PMMA cover plate of equal dimensions. To incorporate the electrodes, the bonded chip is heated to 80 °C, above the melting point of the alloy (≈ 70 °C) and below the glass transition temperature of the PMMA (≈ 105 °C), and the molten alloy drawn into the electrode channels with a syringe before being allowed to cool and harden. A 0.5 mm diameter stainless steel pin is then inserted into the alloy filled reservoirs of the electrode channels to provide external connection to the capacitively coupled contactless conductivity detection detector electronics. This advance provides for a quick and simple manufacturing process and negates the need for integrating electrodes using costly and time-consuming thin film deposition methods. No additional detector cell mounting structures were required and connection to the external signal processing electronics was achieved by simply slipping commercially available shielded adaptors over the pins. With a non-optimised electrode arrangement consisting of a 1 mm detector gap and 100 μm insulating distance, rapid separations of ammonium, sodium and lithium (<22 s) yielded LODs of approximately 1.5-3.5 ppm.

Ultrafast amplification of DNA on plastic microdevices for forensic short tandem repeat analysis

The majority of microfluidic devices used as a platform for low-cost, rapid DNA analysis are glass devices; however, microchip fabrication in glass is costly and laborious, enhancing the interest in polymeric substrates, such as poly (methyl methacrylate) (PMMA), as an inexpensive alternative. Here, we report amplification in PMMA polymerase chain reaction (PCR) microchips providing full short tandem repeat profiles (16 of 16 loci) in 30-40 min, with peak height ratios and stutter percentages that meet literature threshold requirements. In addition, partial profiles (15 of 16 loci) were generated using an ultrafast PCR method in 17.1 min, representing a ~10-fold reduction in reaction time as compared to current amplification methods. Finally, a multichamber device was demonstrated to simultaneously amplify one positive, one negative, and five individual samples in 39 min. Although there were instances of loci dropout, this device represents a first step toward a microfluidic system capable of amplifying more than one sample simultaneously.

Real-time monitoring of strand-displacement DNA amplification by a contactless electrochemical microsystem using interdigitated electrodes

This paper reports the design and implementation of a contactless conductivity detection system which combines a thermal control cell, a data processing system and an electrochemical (EC) cell for label-free isothermal nucleic acid amplification and real-time monitoring. The EC cell consists of a microchamber and interdigitated electrodes as the contactless conductivity biosensor with a cover slip as insulation. In our work, contactless EC measurements, the effects of trehalose on amplification, and chip surface treatment are investigated. With the superior performance of the biosensor, the device can detect the amount of pure DNA at concentrations less than 0.1 pg μl(-1). The EC cell, integrated with a heater and a temperature sensor, has successfully implemented nicking-based strand-displacement amplification at an initial concentration of 2.5 μM and the yields are monitored directly (dismissing the use of probes or labels) on-line. This contactless detector carries important advantages: high anti-interference capability, long detector life, high reusability and low cost. In addition, the small size, low power consumption and portability of the detection cell give the system the potential to be highly integrated for use in field service and point of care applications.

Electrochemical methods in conjunction with capillary and microchip electrophoresis

Electromigrative techniques such as capillary and microchip electrophoresis (CE and MCE) are inherently associated with various electrochemical phenomena. The electrolytic processes occurring in the buffer reservoirs have to be considered for a proper design of miniaturized electrophoretic systems and a suitable selection of buffer composition. In addition, the control of the electroosmotic flow plays a crucial role for the optimization of CE/MCE separations. Electroanalytical methods have significant importance in the field of detection in conjunction with CE/MCE. At present, amperometric detection and contactless conductivity detection are the predominating electrochemical detection methods for CE/MCE. This paper reviews the most recent trends in the field of electrochemical detection coupled to CE/MCE. The emphasis is on methodical developments and new applications that have been published over the past five years. A rather new way for the implementation of electrochemical methods into CE systems is the concept of electrochemically assisted injection which involves the electrochemical conversions of analytes during the injection step. This approach is particularly attractive in hyphenation to mass spectrometry (MS) as it widens the range of CE-MS applications. An overview of recent developments of electrochemically assisted injection coupled to CE is presented.