High-Luminescence Electrospun Polymeric Microfibers In Situ Embedded with CdSe Quantum Dots with Excellent Environmental Stability for Heat and Humidity Wearable Sensors

In this paper, hydrophobic luminescent CdSe quantum dots are successfully dispersed in a mixture of styrene and methyl methacrylate through the oleic to methacrylic acid ligand exchange. Further in situ solution polymerization of the quantum dots in a mixture of styrene and methyl methacrylate followed by electrospinning allowed us to prepare luminescence hybrid styrene-co-methyl methacrylate fibers embedded with quantum dots. CdSe@P(S+MMA) hybrid fibers with 27% quantum yield showed excellent moisture, heat and salt resistance with a photoluminescence output below 120 °C. When dry heated, the hybrid fibers of the fluorescence signals decreased with temperature to 79%, 40%, 28%, 20% and 13% at 120 °C, 140 °C, 160 °C, 180 °C and 200 °C, respectively, due the to the chemical degradation of CdSe QDs. Such hybrid fibers show the potential to manufacture wearable moisture- and heat-sensing protective clothing in a 120–200 °C range due to the thermal-induced quenching of quantum dot photoluminescence.

Response surface methodological optimization of batch Cu(II) sorption onto succinic acid functionalized SiO2 nanoparticles

Functionalizing nanosilica (n-SiO2) particles with suitable active organic moiety leads to the formation of surfaces with precisely controlled physical and chemical characteristics. In this work, a novel nanosorbent (31 ± 2.4 nm), namely succinic acid functionalized nanosilica (n-SiO2@SA), was synthesized via a simple protocol using microwave irradiation to remove Cu(II) ions from aqueous media. The successful functionalization of n-SiO2 was confirmed by FTIR, and the thermal stability of n-SiO2@SA was investigated by TGA study. Other techniques, including HRTEM, DLS and zeta-potential, were utilized to investigate the chemical, surface, and morphological properties of the fabricated n-SiO2@SA. The response surface methodology (RSM) combined with three-level, three-factorial Box–Behnken design (BBD) was applied to optimize the multivariable sorption system using data obtained from 17 batch runs to reach 98.9% of Cu(II) ion removal. The predicted optimal conditions were as follows: contact time = 30 min, pH = 7.1, initial Cu(II) concentration = 317.5 mg L−1, and sorbent dose = 15 mg at which the maximum sorption capacities for n-SiO2 and n-SiO2@SA were 209.3 and 386.4 mg g−1, respectively, at 25 °C, thus supporting the validity of functionalization process. Non-linear regression and linear least-squares methods confirm the suitability of Langmuir model to describe the experimental endothermic, feasible, and chemisorption data, whereas the normalized standard deviation Δq% recommends the pseudo second-order kinetic model to represent the kinetic data. Real Cu-contaminated wastewaters were used to examine n-SiO2@SA nanosorbent for removing Cu(II) ions.

A polydopamine layer as the nucleation center of MOF deposition on “inert” polymer surfaces to fabricate hierarchically structured porous films

Polydopamine could be used as an effective nucleation center for MOF deposition on “inert” polymer membranes, affording hierarchically structured porous films.

Conjugated polymer dots-on-electrospun fibers as a fluorescent nanofibrous sensor for nerve gas stimulant

A novel chemical warfare agent sensor based on conjugated polymer dots (CPdots) immobilized on the surface of poly(vinyl alcohol) (PVA)-silica nanofibers was prepared with a dots-on-fibers (DoF) hybrid nanostructure via simple electrospinning and subsequent immobilization processes. We synthesized a polyquinoxaline (PQ)-based CP as a highly emissive sensing probe and employed PVA-silica as a host polymer for the elctrospun fibers. It was demonstrated that the CPdots and amine-functionalized electrospun PVA-silica nanofibers interacted via an electrostatic interaction, which was stable under prolonged mechanical force. Because the CPdots were located on the surface of the nanofibers, the highly emissive properties of the CPdots could be maintained and even enhanced, leading to a sensitive turn-off detection protocol for chemical warfare agents. The prepared fluorescent DoF hybrid was quenched in the presence of a chemical warfare agent simulant, due to the electron transfer between the quinoxaline group in the polymer and the organophosphorous simulant. The detection time was almost instantaneous, and a very low limit of detection was observed (∼1.25 × 10(-6) M) with selectivity over other organophosphorous compounds. The DoF hybrid nanomaterial can be developed as a rapid, practical, portable, and stable chemical warfare agent-detecting system and, moreover, can find further applications in other sensing systems simply by changing the probe dots immobilized on the surface of nanofibers.

Organic-Inorganic Hybrid Polymers as Adsorbents for Removal of Heavy Metal Ions from Solutions: A Review

Over the past decades, organic-inorganic hybrid polymers have been applied in different fields, including the adsorption of pollutants from wastewater and solid-state separations. In this review, firstly, these compounds are classified. These compounds are prepared by sol-gel method, self-assembly process (mesopores), assembling of nanobuilding blocks (e.g., layered or core-shell compounds) and as interpenetrating networks and hierarchically structures. Lastly, the adsorption characteristics of heavy metals of these materials, including different kinds of functional groups, selectivity of them for heavy metals, effect of pH and synthesis conditions on adsorption capacity, are studied.