One-step packing of anti-voltage photonic crystals into microfluidic channels for ultra-fast separation of amino acids and peptides

Electrophoretic Determination of L-Carnosine in Health Supplements Using an Integrated Lab-on-a-Chip Platform with Contactless Conductivity Detection

The health supplement industry is one of the fastest growing industries in the world, but there is a lack of suitable analytical methods for the determination of active compounds in health supplements such as peptides. The present work describes an implementation of contactless conductivity detection on microchip technology as a new strategy for the electrophoretic determination of L-carnosine in complex health supplement formulations without pre-concentration and derivatization steps. The best results were obtained in the case of +1.00 kV applied for 20 s for injection and +2.75 kV applied for 260 s for the separation step. Under the selected conditions, a linear detector response of 5 × 10-6 to 5 × 10-5 M was achieved. L-carnosine retention time was 61 s. The excellent reproducibility of both migration time and detector response confirmed the high precision of the method. The applicability of the method was demonstrated by the determination of L-carnosine in three different samples of health supplements. The recoveries ranged from 91 to 105%. Subsequent analysis of the samples by CE-UV-VIS and HPLC-DAD confirmed the accuracy of the obtained results.

Effect of Hydrophobic Moieties on the Assembly of Silica Particles into Colloidal Crystals

To boost the implementation of colloidal crystals (CCs) in separation science, the effects of the most common chromatographic reversed phases, that is, butyl and octadecyl, on the assembly of silica particles into CCs and on the optical properties of CCs are investigated. Interestingly, particle surface modification can cause phase separation during sedimentation because the assembly is highly sensitive to minute changes in surface characteristics. Solvent-induced surface charge generation through acid-base interactions of acidic residual silanol groups with the solvent is enough to promote colloidal crystallization of modified silica particles. In addition, solvation forces at small interparticle distances are also involved in colloidal assembly. The characterization of CCs formed during sedimentation or via evaporative assembly revealed that C4 particles can form CCs more easily than C18 particles because of their low hydrophobicity; the latter can only form CCs in tetrahydrofuran when C18 chains with a high bonding density have extra hydroxyl side groups. These groups can only be hydrolyzed from trifunctional octadecyl silane but not from a monofunctional one. Moreover, after evaporative assembly, CCs formed from particles with different surface moieties exhibit different lattice spacings because their surface hydrophobicity and chemical heterogeneity can modulate interparticle interactions during the two main stages of assembly: the wet stage of crystal growth and the late stage of nano dewetting (evaporation of interparticle solvent bridges). Finally, short, alkyl-modified CCs were effectively assembled inside silica capillaries with a 100 μm inner diameter, laying the foundation for future chromatographic separation using capillary columns.

Submicron Nonporous Silica Particles for Enhanced Separation Performance in pCEC

Applications of submicron-scale particles are of rising interest in separation science due to their favorable surface-to-volume ratio and their fabrication of highly ordered structures. The uniformly dense packing beds in columns assembled from nanoparticles combined with an electroosmotic flow-driven system has great potential in a highly efficient separation system. Here, we packed capillary columns using a gravity method with synthesized nanoscale C18-SiO₂ particles having diameters of 300-900 nm. The separation of small molecules and proteins was evaluated in the packed columns on a pressurized capillary electrochromatography platform. The run-to-run reproducibility regarding retention time and peak area for the PAHs using a column packed with 300 nm C18-SiO₂ particles were less than 1.61% and 3.17%, respectively. Our study exhibited a systematic separation analysis of small molecules and proteins based on the columns packed with submicron particles combined with the pressurized capillary electrochromatography (pCEC) platform. This study may provide a promising analytical approach with extraordinary column efficiency, resolution, and speed for the separation of complex samples.

Dendritic Mesoporous Silica Nanospheres: Toward the Ultimate Minimum Particle Size for Ultraefficient Liquid Chromatographic Separation

Use of smaller particle size of packing materials in liquid chromatography leads to faster separation and higher efficiency. This basic law has driven the evolution of packing materials for several generations. However, the use of nanoscale packing materials has been severely hampered by extremely high back pressure. Here, we report a new possibility of solving this issue via introducing novel nanomaterials with highly favorable structures. n-Octyl-modified monodispersed dendritic mesoporous silica nanospheres (DMSNs) with an unprecedentedly small diameter (ca. 170 nm) and appropriate pore size (5.6 nm) were controllably synthesized and demonstrated to be a practically applicable packing material offering ultrahigh efficiency. The center-radial centrosymmetric mesopore channels significantly improved the permeability of packed capillaries, enabling column packing and capillary electrochromatographic separation on regular instruments. Due to the unique morphology, very tiny particle size, and highly uniform packing, the packed column exhibited ultrahigh efficiency up to 3 500 000 plates/m. Powerful separation capability was demonstrated with glycan profiling of cancerous and normal cells, which revealed that cancerous cells exhibited characteristic N-glycans. Because DMSNs with tunable particle size and mesopores can be controllably prepared, DMSNs hold great potential to be a new record toward the ultimate generation of packing materials for ultraefficient liquid chromatographic separation.

A substantial increase of analytical throughput in capillary electrophoresis throughput by separation-interrupted sequential injections

How to further improve the throughput of capillary electrophoresis (CE) is a fascinating question. Herein an idea to substantially increase the throughput of CE has been proposed together with theory and experimental demonstration. The key is to introduce samples for CE, one after another, by a short suspension of voltage application, which was hence termed separation-interrupted sequential injections (Sisi). The idea was demonstrated to be feasible on a laboratory-built CE instrument coupled with tandem C4D (contactless capacitively-coupled conductivity) detectors. At least 50 injections of a testing sample (mixture of NH4+, K+, Ca2+, Na+ and Mg2+) were successfully separated in only a single run. The separation took 145 min in total, equivalent to 2.9 min per analysis which is only 21% of that of normal CE. Quantification of the separated ions was performed, with a limit of detection of 1.1-2.6 μM, a limit of quantification of 3.2-8.9 μM, and a linear range up to 1000 μM (R2 > 0.99). The recovery was between 88% and 112% measured by spiking standards into samples at low, middle and high levels. The real applicability of Sisi-CE was evaluated by direct injection and analysis of 45 mineral water samples also in a single run. Its clinical application potential was demonstrated by high throughput assay of the calcium and zinc gluconate oral solution formula, and the blood potassium of hyperkalemia and hypokalemia from patients with renal failure disease. This method can be extended to other applications such as omics studies through the use of more suitable detectors. The theory proposed may also be applicable to other high throughput methods.

Preparation of Monolayer Photonic Crystals from Ag Nanobulge-Deposited SiO2 Particles as Substrates for Reproducible SERS Assay of Trace Thiol Pesticide

Surface-enhanced Raman scattering (SERS) greatly increases the detection sensitivity of Raman scattering. However, its real applications are often degraded due to the unrepeatable preparation of SERS substrates. Herein presented is a very facile and cost-effective method to reproducibly produce a novel type of SERS substrate, a monolayer photonic crystal (PC). With a building block of laboratory-prepared monodisperse SiO₂ particles deposited with space-tunable silver nanobulges (SiO₂@nAg), a PC substrate was first assembled at the air-water interface through needle tip flowing, then transferred onto a silicon slide by a pulling technique. The transferred monolayer PCs were characterized by SEM and AFM to have a hexagonal close-packed lattice. They could increase Raman scattering intensity by up to 2.2 × 10⁷-fold, as tested with p-aminothiophenol. The relative standard deviations were all below 5% among different substrates or among different locations on the same substrate. The excellent reproducibility was ascribed to the highly ordered structure of PCs, while the very high sensitivity was attributed to the strong hotspot effect caused by the appropriately high density of nanobulges deposited on SiO₂ particles and by a closed lattice. The PC substrates were validated to be applicable to the SERS assay of trace thiol pesticides. Thiram pesticide is an example determined in apple juice samples at a concentration 10²-fold lower than the food safety standard of China. This method is extendable to the analysis of other Raman-active thiol chemicals in different samples, and the substrate preparation approach can be modified for the fabrication of more PC substrates from other metallic nanobulge-deposited particles rather than silica only.

Separation-cooperated assembly of liquid photonic crystals from polydisperse particles

Easy and cost-effective production of high-quality photonic crystals (PCs) remains challenging but attractive, not just because they are a type of gemstone but more for their scientific applications (e.g., serving as lossless waveguides, visual sensors, novel pigments and novel separation media). Herein presented is a separation-cooperated assembly (SCA) strategy able to organize cheap polydisperse particles into PCs. Its feasibility was validated through sink-induced SCA of poorly disperse (size variation up to 56%) particles into iridescent liquid PCs in 3 days or more. Strikingly, with a sharp photonic band gap down to 10 nm (ca. 1/7 of the reported 66 nm), the liquid PCs are able to cyclically recover their iridescent color in ca 20 s after agitation, and keep their structural order after dryness, making them practicable to write and paint directly. Also significant is that SCA yielded uniform particles with size variation down to 0.7%. It is thus an easy way to isolate homogeneous particles from disperse ones.

Multi-functional organosilane-polymerized carbon dot inverse opals

This paper demonstrates multi-functional optical properties of organosilane-polymerized carbon dot inverse opals, such as tricolor-fluorescence, fluorescence enhancement, multi-color micro-patterns for anti-fake applications and a thermally-induced blueshift of bandgaps. It is of significance for the design and fabrication of novel optical devices.

Hierarchically structured photonic crystals for integrated chemical separation and colorimetric detection

A SiO₂ colloidal photonic crystal film with a hierarchical porous structure is fabricated to demonstrate an integrated separation and colorimetric detection of chemical species for the first time. This new photonic crystal based thin layer chromatography process requires no dyeing, developing and UV irradiation compared to the traditional TLC. The assembling of mesoporous SiO₂ particles via a supersaturation-induced-precipitation process forms uniform and hierarchical photonic crystals with micron-scale cracks and mesopores, which accelerate the diffusion of developers and intensify the adsorption/desorption between the analytes and silica for efficient separation. Meanwhile, the chemical substances infiltrated to the voids of photonic crystals cause an increase of the refractive index and a large contrast of structural colors towards the unloaded part, so that the sample spots can be directly recognized with the naked eye before and after separation.

Analysis of proteins and peptides by electromigration methods in microchips

This review presents the developments and applications of microchip electromigration methods in the separation and analysis of peptides and proteins in the period 2011-mid-2016. The developments in sample preparation and preconcentration, microchannel material, and surface treatment are described. Separations by various microchip electromigration methods (zone electrophoresis in free and sieving media, affinity electrophoresis, isotachophoresis, isoelectric focusing, electrokinetic chromatography, and electrochromatography) are demonstrated. Advances in detection methods are reported and novel applications in the areas of proteomics and peptidomics, quality control of peptide and protein pharmaceuticals, analysis of proteins and peptides in biomatrices, and determination of physicochemical parameters are shown.

Integrated microfluidic device for the spherical hydrogel pH sensor fabrication

A type of inverse opal hydrogel pH sensor with homogeneous structural colour were generated from an integrated microfluidic chip.

Fast assembly of anti-voltage photonic crystals in microfluidic channels for ultrafast separation of amino acids and peptides

Photonic crystals (PCs) with periodically ordered particle beds are ideal media for high-performance separation but hard to be stably and crack-freely assembled in various microfluidic channels. Here we describe a facile method to fast assemble crack-free and high-voltage-sustainable PCs into the micro channels. The key is to speed up an evaporation-induced assembly by heating up (at 70 °C) and blowing away the solvent vapor from one end of a channel and supplying silica suspension at the other end. Crack-free PCs can be prepared at a speed of 0.2 cm/min. The heat also accelerates the silica particles to gel with solvent water and in turn to form a particle network by linking each other through their gelled surface. PCs with two pieces of particle network at their ends are capable of resistance to electrical fields up to 2,000 V/cm. Ultrafast separation of amino acids can be achieved along a 2.5-mm PC in 4 s and peptides along a 10-mm PC in 12 s.

Present state of microchip electrophoresis: state of the art and routine applications

Microchip electrophoresis (MCE) was one of the earliest applications of the micro-total analysis system (μ-TAS) concept, whose aim is to reduce analysis time and reagent and sample consumption while increasing throughput and portability by miniaturizing analytical laboratory procedures onto a microfluidic chip. More than two decades on, electrophoresis remains the most common separation technique used in microfluidic applications. MCE-based instruments have had some commercial success and have found application in many disciplines. This review will consider the present state of MCE including recent advances in technology and both novel and routine applications in the laboratory. We will also attempt to assess the impact of MCE in the scientific community and its prospects for the future.

Simultaneous determination of electrophoretic and dielectrophoretic mobilities of human red blood cells

Electrophoresis and dielectrophoresis of cells can reveal many distinct cellular properties but are often conducted separately. Herein a simultaneous strategy was proposed, and a simple method was established by making cells migrate through a cross channel under a micro video for real-time observation. The experiment can be performed within 0.044-1 s. In combination with digital calculation based on electromagnetic theory, the method was validated to be applicable to the determination of electrophoretic and dielectrophoretic mobilities, μEP and μDEP , of human blood erythrocytes, giving μEP = -(0.87 ± 0.16)× 10(-4) cm(2) ·V(-1) · s(-1) and μDEP = -(4.5 ± 1.3) × 10(-8) cm(4) ·V(-2) ·s(-1) by vector decomposition, or μEP = -(0.89 ± 0.14) × 10(-4) cm(2) ·V(-1) · s(-1) and μDEP = -(4.6 ±1.2) × 10(-8) cm(4) ·V(-2) · s(-1) by least squares fitting, all agreeing with published data. Hydrodynamic and EOFs were eliminated for better measurement. It was found that the location of cells had a serious impact on the measurement precision, and the upstream of the cross channel along the electric field was chosen for precise measurement. The method is also extendable to the study of other cells and particles.