Whole ceramic-like microreactors from inorganic polymers for high temperature or/and high pressure chemical syntheses

Fabrication of Ceramic Microchannels with Periodic Corrugated Microstructures as Catalyst Support for Hydrogen Production via Diamond Wire Sawing

Hydrogen energy is the clean energy with the most potential in the 21st century. The microchannel reactor for methanol steam reforming (MSR) is one of the effective ways to obtain hydrogen. Ceramic materials have the advantages of high temperature resistance, corrosion resistance, and high mechanical strength, and are ideal materials for preparing the catalyst support in microchannel reactors. However, the structure of ceramic materials is hard and brittle, and the feature size of microchannel is generally not more than 1 mm, which is difficult to process using traditional processing methods. Diamond wire saw processing technology is mainly used in the slicing of hard and brittle materials such as sapphire and silicon. In this paper, a microchannel with a periodic corrugated microstructure was fabricated on a ceramic plate using diamond wire sawing, and then as a catalyst support when used in a microreactor for MSR hydrogen production. The effects of wire speed and feed speed on the amplitude and period size of the periodic corrugated microstructure were studied using a single-factor experiment. The microchannel surface morphology was observed via SEM and a 3D confocal laser microscope under different processing parameters. The microchannel samples obtained under different processing parameters were supported by a multiple impregnation method. The loading strength of the catalyst was tested via a strong wind purge experiment. The experimental results show that the periodic corrugated microstructure can significantly enhance the load strength of the catalyst. The microchannel catalyst support with the periodic corrugated microstructure was put into the microreactor for a hydrogen production experiment, and a good hydrogen production effect was obtained. The experimental results have a positive guiding effect on promoting ceramic materials as the microchannel catalyst support for the development of hydrogen energy.

Design, Fundamental Principles of Fabrication and Applications of Microreactors

This study highlights the development of small-scale reactors, in the form of microstructures with microchannel networking. Microreactors have achieved an impressive reputation, regarding chemical synthesis ability and their applications in the engineering, pharmaceutical, and biological fields. This review elaborates on the fabrication, construction, and schematic fundamentals in the design of the microreactors and microchannels. The materials used in the fabrication or construction of the microreactors include silicon, polymer, and glass. A general review of the application of microreactors in medical, biological, and engineering fields is carried out and significant improvements in these areas are reported. Finally, we highlight the flow patterns, mixing, and scaling-up of multiphase microreactor developments, with emphasis on the more significant industrial applications.

Multilayered film microreactors fabricated by a one-step thermal bonding technique with high reproducibility and their applications

We report the versatile uses of multilayered polyimide (PI) film microreactors with various functions including pressure tolerance, three-dimensional mixing and multistep membrane emulsification. Such PI film microreactors were fabricated by a simple one-step thermal bonding technique with high reproducibility. Upon bonding at 300 °C for 1 hour, the thin and flexible film microdevices could withstand pressure up to 8.6 MPa and 16.3 MPa with PI adhesive film or fluoropolymer adhesive, respectively, due to differences in wettability. The hydrophilic and hydrophobic microchannel devices were used to generate monodisperse oil-in-water (O/W) and water-in-oil (W/O) droplets, and polymer micro/nanoparticles at a high generation frequency. A monolithic and chemical resistant film microreactor with a three-dimensional serpentine microchannel was used for the selective reduction of ester to aldehyde by efficient mixing and quenching in a flash chemistry manner, within a several 10(1) millisecond time scale. Furthermore, a novel multilayered film microreactor for organic-aqueous biphasic interfacial reactions was devised by embedding a membrane layer to induce chaotic mixing in both the interface and emulsified phase by flowing through multiple numbers of meshed structures along the hydrophobic channel. This simple and economic fabrication technique significantly facilitates mass production of multilayered film devices that could be useful as a platform for various microfluidic applications in chemistry and biology.

A pressure-tolerant polymer microfluidic device fabricated by the simultaneous solidification-bonding method and flash chemistry application

Pressure-tolerant polymer-glass microfluidic reactors with excellent bonding strength have been fabricated by the simultaneous solidification-bonding (SSB) method, in which a viscous and reactive matrix polymer was cast on the glass substrate with pre-patterned wax as a sacrificial template. Elaborate interfacial chemistry between the matrix polymer and the functionalized glass surface was designed to achieve simultaneous solidification and chemical bonding under UV or/and mild thermal conditions (<200 °C with no pressure). Highly pressure-tolerant microchannels were obtained by complete removal of the liquid wax template at 80 °C. Versatility was demonstrated by fabricating microreactors from various polymers with different interfacial chemistry, which were all stable at 1000 psi with the highest burst pressure of 2000 psi. In particular, the fluoropolymer-glass microreactor can withstand a burst pressure that is two orders of magnitude higher than that of the microchannel made by the conventional method. Finally, the polymer-glass microfluidic device was used for the synthesis of a natural product, tryptanthrin, by flash chemistry under high pressure induced conditions (synthetic yield: 90%, flow rate: 10.5 mL min(-1), reaction time: 14 ms). The transparent microfluidic device can be used as a useful platform for miniaturizing spectroscopic tools for chemical analysis studies under high pressure conditions.

Solvent immersion imprint lithography

We present Solvent Immersion Imprint Lithography (SIIL), a technique for polymer functionalization and microsystem prototyping. SIIL is based on polymer immersion in commonly available solvents. This was experimentally and computationally analyzed, uniquely enabling two practical aspects. The first is imprinting and bonding deep features that span the 1 to 100 μm range, which are unattainable with existing solvent-based methods. The second is a functionalization scheme characterized by a well-controlled, 3D distribution of chemical moieties. SIIL is validated by developing microfluidics with embedded 3D oxygen sensors and microbioreactors for quantitative metabolic studies of a thermophile anaerobe microbial culture. Polystyrene (PS) was employed in the aforementioned applications; however all soluble polymers - including inorganic ones - can be employed with SIIL under no instrumentation requirements and typical processing times of less than two minutes.